63 MHz SAW Filter 0.55 MHz Bandwidth Part Number: SF0063BA03106S DESCRIPTION • • 63 MHz SAW bandpass filter with 0.55 MHz bandwidth in 19 x 6.55 mm SMP. RoHS compliant. TYPICAL PERFORMANCE 61 63 Vertical from top: S11 (61-65 MHz) Relative Magnitude : Relative magnitude : Group Delay Deviation : 65 10 1 500 dB/div dB/div ns/div S22 (61-65 MHz) Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0063BA03106S Rev A 9-Feb-2010 ECN 36650 Page 1 of 3 63 MHz SAW Filter 0.55 MHz Bandwidth Part Number: SF0063BA03106S SPECIFICATION Parameter Center Frequency, FC 1 Insertion Loss at 63 MHz 1 dB Bandwidth 2 3 dB Bandwidth 2 35 dB Bandwidth 2 Relative Attenuation (61 to 62.25 MHz) Relative Attenuation (63.75 to 65 MHz) Relative Attenuation (10 to 61 MHz) Relative Attenuation (65 to 140 MHz) Passband Ripple Group Delay Ripple (Fc +/- 0.2 MHz) Absolute Delay Source/Load Impedance Notes: Min 62.95 0.35 0.55 35 35 43 43 - Typ 63 8.35 0.41 0.58 1.35 42 38 55 49 0.2 300 1.95 50 Max 63.05 9 1.4 1.0 520 - Units MHz dB MHz MHz MHz dB dB dB dB dB p-p ns p-p us ohms 1. Defined as the average of the lower and upper 3 dB frequencies. 2. All dB levels are defined relative to the insertion loss at 63 MHz. MAXIMUM RATINGS Parameter Storage Temperature Range Operating Temperature Range Input Power Level Min Max -40 -40 85 8 10 Units ˚C ˚C dBm MATCHING CIRCUIT 10 5 Input 50 Ω Single-ended Output 50 Ω Single-ended All others GND GND Typical component values: (Minimum inductor Q = 40) Ls1 Cp1 = = 540 100 nH pF Ls2 = Cp2 = 616 82 nH pF Notes: 1. Recommend use of 2% tolerance matching components. 2. Component values are for reference only and may change depending on board layout. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0063BA03106S Rev A 9-Feb-2010 ECN 36650 Page 2 of 3 63 MHz SAW Filter 0.55 MHz Bandwidth Part Number: SF0063BA03106S PACKAGE OUTLINE SUGGESTED FOOTPRINT Units: mm Tolerances are ±0.15 mm except for the overall length, width and pad dimensions, which are nominal values. Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 µm min, over a 1.3-8.9 µm Ni plating Pad Configuration: Input: 10 Input return: 1 Output: 5 Output return: 6 Ground: 2,3,4,7,8,9 ISO 9001 Registered All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves the right to make changes without notice. © 2010 All rights reserved. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0063BA03106S Rev A 9-Feb-2010 ECN 36650 Page 3 of 3