4238-63.75 - Weinschel

Programmable Attenuators
Model 4238
GaAs Switched Programmable
Attenuator
10 MHz to 2.5 GHz
1 Watt
RoHS
Low Insertion Loss, High IP3
INCREMENTAL ATTENUATION ACCURACY:
CELL
0.25
0.50
dB
+0.15
+0.15 +0.2 +0.2
1
2
4
8
16
+0.2 +0.2 +0.3
24
32
48
+0.4 +0.6 +0.8
MAXIMUM INSERTION LOSS (dB):
Frequency Range (GHz)
4238-X
0.01 - 1.0
1.0 - 2.0
2.0 - 2.5
Features
Ideal for use in Wireless/Cellular, RF Simulation/Emulation,
& Communication Test Applications.
o Broadband Performance - 10 MHz to 2.5 GHz
usable dc to 10 MHz with reduced specifications
o High IP3 and High Power Rating
- Utilizes MESFET Switching
o Flexible DC Voltage (+5 to +15 V)
o Low DC Power Consumption - Ideal for portable
battery powered equipment.
o Custom Configurations including bus controlled
attenuator subsystems
Specifications
NOMINAL IMPEDANCE: 50 Ω
FREQUENCY RANGE: 10 MHz to 2.5 GHz
MAXIMUM SWR:
Frequency Range (GHz)
0.01 - 0.25
0.25 - 2.5
SWR
1.75
1.40
CELL CONFIGURATIONS:
Model
NO.
Attenuation
Number
Cells Range/Steps
(dB)
Cell
Increments
(dB)
4238-63.75
8
63.75/0.25
0.25, 0.5, 1, 2, 4, 8,
16, 32
4238-103
8
103/1
1, 2, 4, 8, 16, 24, 48
6.75
8.25
9.75
MONOTONICITY: 10 MHz to 2.5 GHz
(minimum 1 dB change)
3rd ORDER INTERMODULATION (IM3): -60 dBm typical,
measured with two +27 dBm tones @ 869 MHz (f1) and
894 MHz (f2), the IM3 frequency being 847 MHz (2fl-f2).
IP3 (input) = +65 dBm
The input IP3 is derived from the following relationship:
IP3 = 3(Pin-α)-IM3 + α
2
where α = the insertion loss (dB) at the IM3 frequency;
Pin=single tone input power (dBm).
INPUT POWER RATING: +30 dBm
SWITCHING TIME: 5 μsec. maximum
OPERATING VOLTAGE: + 5 to +15 V
OPERATING CURRENT: 25 mA typical
TEMPERATURE RANGE (Operating): 0°C to +70°C
TEMPERATURE COEFFICIENT: <0.002/dB/dB/°C
CONNECTORS: SMA female connectors - mate nondestructively with MIL-C-39012 connectors.
CONTROL CONNECTOR: AMP-Latch 10 pin ribbon cable
connector mates with AMP P/N 746285-1 (supplied with
each unit)
WEIGHT:
4238-X
150 g (5.3 oz)
CONTROL CONFIGURATION: Units are supplied with a
built-in TTL interface. Each unit is supplied with a mating 10
pin connector (Amp 746285-1). Refer to Physical
Dimensions for mating connector pin/wiring details. Two
wires are specified for supply voltage and ground. The
remaining wires will accept TTL control signals to activate
or de-activate a particular attenuation cell. A TTL high will
energize a cell to the high attenuation state, whereas a TTL
low will maintain a cell in its zero attenuation state.
243
5305 Spectrum Drive, Frederick, MD 21703-7362 s TEL: 301-846-9222, 800-638-2048 s Fax: 301-846-9116
web: www.aeroflex.com/weinschel s email: [email protected]
Revision Date: 3/6/2013
Programmable Attenuators
PHYSICAL DIMENSIONS:
Model 4238:
Aeroflex / Weinschel
J1
J2
J3
Control Connector J3 Pin Locations:
TTL Conn
PIN No. (J3)
4238-103
dB (Cell)
4238-63.75
dB (Cell)
1
1
0.25
1. All dimensions are given in mm (inches) and are maximum, unless
otherwise specified.
2
2
0.50
2. Unit available with RoHS compliant materials, specify when ordering.
3
4
1
4
8
2
5
16
4
6
24
8
7
48
16
8
NC*
32
9
+5 to 15V
+5 to 15V
10
COM
COM
NOTE:
NC = Not Connected
* For Factory use only.
244
5305 Spectrum Drive, Frederick, MD 21703-7362 s TEL: 301-846-9222, 800-638-2048 s Fax: 301-846-9116
web: www.aeroflex.com/weinschel s email: [email protected]
Revision Date: 3/6/2013