IS01BCCF Version (1) DISTINCTIVE CHARACTERISTICS Enhanced LED Illumination with: • Broad and even light distribution • Consistent bright backlighting • Lower energy consumption Programmable to display graphics, alphanumeric characters and animated sequences. SMARTDISPLAY can be used alone or in conjunction with electromechanical switches. Integrated liquid crystal display provides wide viewing angle with high contrast and clarity. Viewing area 13.9mm x 10.6mm (horizontal x vertical) at 36 x 24 pixels. Epoxy sealed terminals prevent entry of solder flux and other contaminants. Optional accessories available to enhance panel design and simplify production process. Built-in red/green LED backlighting enhances display and enables multifunctional uses. PRECAUTIONS FOR HANDLING & STORAGE ATTENTION ELECTROSTATIC SENSITIVE DEVICES Handling 1. 2. 3. 4. 5. 6. 7. The VLC voltage should not be applied before logic voltage. If VLC voltage is present before logic voltage, it may cause the driver logic to freeze and damage the LCD, and the driver logic itself may become damaged. The IS Series devices are electrostatic sensitive. Recommended soldering time and temperature limits are 5 seconds maximum @ 270°C maximum. Do not exceed 60°C at the LCD level. The IS series devices are not process sealed. If the LCD is accidentally broken, avoid contact with the liquid and wash off any liquid spills to the skin or clothing. Clean cap surface with dry cloth. If further cleaning is needed, wipe with dampened cloth using neutral cleanser and dry with clean cloth. Do not use organic solvent. Storage 1. Store away from direct sunlight. 2. Keep away from static electricity. 3. Avoid extreme temperatures, high humidity, gaseous substances, and all forms of chemical contamination. NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkksmartswitch.com 1 SMARTDISPLAY TM LCD SPECIFICATIONS Characteristics of Display Display Operation Mode STN positive Display Condition Transflective with built-in LED backlight Viewing Angle Adjustable Driving Method 1/24 duty. 1/5 bias (built-in driving circuit) Viewing Area 13.9mm x 10.6mm (horizontal x vertical) Pixel Format 36 x 24 dots (horizonal x vertical) Pixel Size 0.32mm x 0.32mm (horizontal x vertical) Operating Temperature Range 0°C through 40°C (32°F through 104°F) Storage Temperature Range –10°C through 60°C (14°F through 140°F) Backlight LED Red/Green Red/Green Bicolor LED with Yellow LCD Mode Absolute Maximum Ratings (Temperature at 25°C) Recommended Operating Conditions (Temperature at 25°C) Items Symbols Ratings Items Symbols Minimum Typical Maximum 5.5V Supply Voltage for Logics VDD – 0 .3V to +7.0V Supply Voltage for Logics VDD 4.5V 5.0V Supply Voltage for LCD VL C – 0 .3V to +12.0V Supply Voltage LCD VL C –– 7.3V –– Input Voltage VI – 0 .3V to VDD +0.3V Input Voltage VI 0V –– VDD Output Voltage VO – 0 .3V to VDD +0.3V Driving Frequency f FLM –– 150Hz –– DC Characteristics of LCD Drive IC (Temperature at 0°C to 40°C and VD D = 5.0V ±10%) Items Symbols High Level Input Voltage Test Conditions Minimum Typical V IH 0.7V DD 0 Maximum Unit V DD V Low Level Input Voltage V I L 0.3 V DD V High Level Input Leakage Current I L I H V I = V DD 10 μA Low Level Input Leakage Current I LIL V I = 0V –10 μA High Level Output Voltage VOH I O H = – 500μA Low Level Output Voltage VOL I O L = 500μA 0.5 V V DD – 0. 5 V High Level Output Leakage Current I L OH VO = V D D 10 μA Low Level Output Leakage Current I L OL VO = 0V –10 μA Supply Current I DD f SC P = 1.0MHz 500 μA LCD Drive Current I LC f L P = 2.4kHz V LC = 7.3V 2,000 μA Timing Characteristics of LCD Drive IC Timing Diagram (Temperature at 0°C to 40°C and VDD = 5.0V ±10%) Items Symbols Minimum Maximum Clock Operation Frequency f S CP 6.0MHz Latch Pulse Frequency f L P 50kHz Clock High Level Pulse Width t CWH 70ns Clock Low Level Pulse Width t CWL 70ns Data Setup Time t DS D 45ns Data Hold Time t DHD 50ns Data Output Delay Time t P D O Latch Setup Time t DS L 50ns Latch Hold Time t DHL 50ns Latch High Level Width t LW H 200ns FLM Setup Time t DS F 50ns FLM Hold Time t DHF 50ns SCP, LP Rise/Fall Time t r/t f 500 tr SCP Din tCWH tCWL tDSD tf tDHD tPDO *1 Dout 25ns LP FLM 15ns *2 tDSL tr *3 tLWH tDSF tDHL tf tDHF *1 Last data on first line *2 Beginning data on second line *3 Location of LP signal on first line NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkksmartswitch.com 2 SMARTDISPLAY TM BLOCK DIAGRAM & PIN CONFIGURATIONS 6 7 5 3 10 Pin No. Symbol FLM SCP Com24 9 Com1 4 V LC V DD Common Driver 1 NC D 24bit CK Shift Register 12 36 x 24 Dot Matrix LCD Panel seg1 Timing Control LP seg36 Segment Driver CK 40bit Latch CK 40bit D Shift RegisterQ Din 11 Dout 8 BL-LED (–) 2 BL-LED (–) GND BL-LED (+) Name 1 VLC 2 BL-LED (–) 3 GND Ground 4 VDD Power Function Power Power source for LCD drive Terminal of Backlight LED Cathode: green Power source for logic circuit 5 Din Data Input Display serial data bit. Note: to map the display data, because of the difference between the number of internal shift register data (40) and the single line of LCD pixels (36), the first four bits of data shifted will be dummy bits. 6 SCP Serial Clock Pulse Clock used by 40-bit internal shift register of the switch, shifting the display data bit presented at Din at falling edge. 7 LP Latch Pulse Line data latch pulse will latch content of internal 40-bit shift register at falling edge for one line of display. LP will also increment the display line by one. 8 BL-LED (–) Terminal of Backlight LED 9 FLM First Line Marker 10 BL-LED (+) Terminal of Backlight LED 11 Dout Data Output 12 NC None Cathode: red The marking signal for the first line data of LCD display. The first line of LCD will be selected by the falling edge of LP signal during the high level (FLM). Anode for common Display serial output. Can be used to connect to Din of the next SMARTDISPLAY. As a result, many SMARTDISPLAYS can be controlled with one clock and data signal. No connection NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkksmartswitch.com 3 SMARTDISPLAY TM SUPER BRIGHT LED SPECIFICATIONS Typical Electrical Characteristics (Temperature at 25°C) Backlight Color Symbols Red/Green Unit Forward Current IF 15/15 mA Forward Voltage VF 2.1/3.3 V ABSOLUTE MAXIMUM FOR LEDS Electrical Characteristics (Temperature at 25°C) Backlight Color Symbols Forward Current IF Reverse Voltage VR Current Reduction Rate Above 25°C ∆ I F( D C ) Power Dissipation* PD Red/Green Unit 20 mA 4.0 V – 0.26 mA/°C 130 maximum mW *For uniform light emission, Power Dissipation should not exceed the Absolute Maximum Rating. TYPICAL DISPLAY DIMENSIONS See Pixel Detail (3.7) .146 (13.9) .547 (12.57) .495 (0.4) Typ .016 (0.8) Dia .031 (10.0) .394 (0.65) Typ .026 Key 2 (10.7) .421 (8.37) .3295 (10.6) .417 (17.2) .677 Part No. (14.4) .567 (17.8) .701 1 (2.0) Typ (16.8) .079 .661 (10.0) .394 (0.5) Sq Typ .020 (8.6) .339 (9.9) .390 12 (0.7) Typ .028 (3.0) .118 (14.7) .579 11 (2.0) Typ .079 (2.0) .079 (15.0) .591 Terminal numbers are not on the device. (0.32) Sq .013 (0.03) Typ .001 1 (10.0) .394 (2.0) .079 Pixel Detail (2.0) Typ .079 CL 3x (0.9) Dia .035 Landless 2 (14.7) (16.8) .579 .661 11 12 (10.0) .394 (15.0) .591 16x (0.9) Dia .035 Footprint NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkksmartswitch.com 4