Series FR01 Toggles General Specifications Rockers Electrical Capacity (Resistive Load) Switching Rating: 100mA @ 5V DC Pushbuttons 10mm DIP Rotaries Other Ratings Programmable Illuminated PB Materials & Finishes G Actuators: Bushing : Outer Case: Housing & Base: Movable Contacts: Stationary Contacts: Terminals: Terminal Cover: Bracket: Accessories Indicators Touch Tilt Tactiles Environmental Data Supplement 100mA @ 50V DC Contact Resistance: 100 milliohms maximum; 30 milliohms maximum for contact point Insulation Resistance: 1,000 megohms minimum @ 250V DC Dielectric Strength: 250V AC minimum for 1 minute minimum Mechanical Life: 10,000 detent operations minimum Electrical Life: 10,000 detent operations minimum Notes: A detent operation is one actuator position operation or stepping. A cycle is one 360° rotation. 10,000 detent operations equal 625 cycles for hexadecimal devices or 1,000 cycles for decimal devices. Nominal Operating Torque: Metal Shaft: 0.009Nm for decimal devices; 0.011Nm for hexadecimal devices All other Actuator types: 0.008Nm for decimal devices; 0.01Nm for hexadecimal devices Contact Timing: Nonshorting Keylocks Rotaries Slides Nonswitching Rating: Operating Temperature Range: Humidity: Vibration: Shock: Screwdriver and Plastic Shaft - Glass fiber reinforced polyamide (UL94V-0); Dial - Polyoxymethylene; Metal Shaft - Brass with nickel plating Brass with nickel plating (for Metal Shaft model) Glass fiber reinforced PBT (for Metal Shaft model) Glass fiber reinforced polyamide (UL94V-0) Copper alloy with gold plating Phosphor bronze with gold plating Phosphor bronze with gold plating Polyamide (Right angle model only) Phospher bronze with tin plating (for Metal Shaft model) –25°C through +85°C (–13°F through +185°F) 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 5 minutes; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Processing Soldering: Wave Soldering Recommended. See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. Note: During soldering process, set the switch to the following position: FR01FR10P, FR01FR16P, FR01KR10P, FR01KR16P, FR01SR10P, FR01SR16P, FR01AR10PB, FR01AR16PB, FR01AR10HB, FR01AR16HB: 0 position; FR01FC10P, FR01KC10P, FR01FC10H, FR01KC10H, FR01SC10P, FR01AC10PB, FR01AC10HB: 7 position; FR01FC16P, FR01KC16P, FR01FC16H, FR01KC16H, FR01SC16P, FR01AC16PB, FR01AC16HB: F position Cleaning: These devices are not process sealed. Hand clean locally using alcohol based solution. Custom process sealed version available; contact factory. Standards & Certifications Flammability Standards: G4 UL94V-0 rated actuator, housing and base The FR01 Series rotaries have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current circuit. When used as intended, the results do not produce hazardous energy. www.nkk.com Series FR01 10mm DIP Rotaries Rockers Toggles Distinctive Characteristics Pushbuttons Compact dimensions and low profile allow high density mounting and close stacking of PC boards. Programmable Illuminated PB Highly visible legends and choice of screwdriver, shaft or dial actuators with arrow position indication provide trouble-free code setting. Knob actuator also available. Detent mechanism gives crisp, positive action for accurate switch setting. Slides G Rotaries Keylocks Real or complement code setting identified by color-keyed actuator. Tactiles Crimped terminals ensure secure PC mounting and prevent dislodging during soldering. Tilt Cam activated movable contact and gold contacts assure contact reliability and continuity. Indicators Actual Size Supplement Accessories Contact factory for custom models with .200” (5.08mm) terminal spacing. Touch Surface mount model with screwdriver actuation available and shown in the surface mount section. www.nkk.com G5 Series FR01 Toggles 10mm DIP Rotaries TYPICAL SWITCH ORDERING EXAMPLE Pushbuttons Rockers FR Mounting Programmable Illuminated PB 01 Through-hole Actuation Screwdriver K Plastic Shaft S Dial (for Straight Terminals only) *A Metal Shaft (for Optional Knobs) Keylocks F 16 R Circuits S P PC Terminals R Real Coded (Orange Actuator) C Complement Coded (Yellow Actuator) P Straight H Right Angle Packaging Stick-Tubes: FR01F, FR01K, FR01S 50 Pieces/Stick FR01A 25 Pieces/Stick S Color not applicable to Actuator A Bracket Positions *Must be used with Bracket 10 Decimal 16 Hexadecimal No Code *B No Bracket With Bracket * For Actuator A only DESCRIPTION FOR TYPICAL ORDERING EXAMPLE G FR01KR16P-S Plastic Shaft Slides Rotaries K 01 Hexadecimal Positions Real Coded Tactiles Packaged in Stick-Tube Straight PC Terminals Tilt MOUNTING 01 Through-hole Touch ACTUATION Indicators F Screwdriver Accessories Adjusted with a flat tipped screwdriver Supplement Actuators are fully rotational either clockwise or counterclockwise. Actuator Colors:Orange for real coded devices; Yellow for complement coded devices. G6 AT4180 Optional Snap-on Knob Polyamide Black knob with transparent flange (2.1) .083 (9.6) .378 (0.8) .031 (6.7) .264 (4.0) .157 (0.8) .031 (1.1) .043 Install knob before mounting on PCB for right angle type; it should not be removed once mounted. When mounting, align slit in knob with arrowhead on actuator. www.nkk.com Series FR01 Toggles 10mm DIP Rotaries ACTUATION Rockers Metal Shaft Programmable Illuminated PB Pushbuttons Knob options illustrated below with color choices Adjusted by hand or with flat tipped screwdriver Actuators are fully rotational and operate either clockwise or counterclockwise. Colors for Actuators K and S: Orange for real coded devices; Yellow for complement coded devices Mounting hardware is available if needed for models with Actuator A: Hexagon Nut AT513M, Locking Ring AT515M, and Lockwasher AT509; all are shown in the Accessories and Hardware section. AT4103 Small Color Tipped AT433 Plain Black (19.0) Dia .748 (11.0) Dia .433 Material: Polyacetal Color: Black (13.0) .512 AT4104 Large Color Tipped (16.0) Dia .630 (9.5) Dia .374 Polyester Base: Black Polyamide Tip Colors: (9.5) .374 (14.3) .563 A, B, C, E, F, G, H (0.5) .020 Keylocks OPTIONAL KNOBS FOR METAL SHAFT (18.0) Dia .709 (11.0) Dia .433 Polyester Base: Black (9.5) .374 (15.8) .622 Polyamide Tip Colors: A, B, C, E, F, G, H (0.5) .020 G (9.5) .374 (0.5) .020 A Black B White C Red E Yellow F Green G Blue Tactiles Knob Orientation: When installed with shaft flat rotated 180° from bushing flat as shown in “Typical Switch Dimensions,” white line on cap points to Actuator Position 0 noted in truth tables below. Color Codes: H Gray 10 Decimal Tilt TRUTH TABLES (CIRCUITS & POSITIONS) Actuator Position x = ON Terminal No. (Output) 16 Hexadecimal 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 A B C D E F 1 C Complement Coded Model Numbers: FR01FC, FR01KC FR01SC, FR01AC Indicators 2 4 8 1 Accessories Model Numbers: FR01FR, FR01KR, FR01SR, FR01AR 2 4 8 Supplement R Real Coded Rotaries Adjusted by hand or with flat tipped screwdriver A Dial Slides S Plastic Shaft Touch K Terminal numbers are actually on the switch. Above sequence shown for clockwise rotation. www.nkk.com G7 Series FR01 Toggles 10mm DIP Rotaries TYPICAL SWITCH DIMENSIONS (0.2) .008 BCD Pushbuttons 78 3 45 23 (3.8) Dia .150 (3.8) Dia .150 1 (2.1) .083 (0.2) Typ .008 (2.54) .100 (10.0) .394 Decimal Hexadecimal (7.62) .300 (1.27) .050 C 1 2 4 8 (0.8 ~ 1.0) Dia Typ .031 ~ .039 2 4 (2.54) Typ .100 8 C (2.54) .100 (0.8 ~ 1.0) Dia Typ .031 ~ .039 (1.27) .050 (3.3) .130 (0.5) Typ .020 (2.54) Typ .100 (3.25) .128 BCD 78 (10.0) .394 01 EF 2 (0.2) Typ .008 (7.62) .300 3 45 901 23 456 Tactiles (2.1) .083 (0.2) .008 (2.54) Typ .100 8 4 2 1 Tilt Decimal FR01KR16P CL 1 2 4 8 C (7.0) (3.8) .276 .150 (0.5) Typ .020 (2.54) Typ .100 (7.62) .300 C (3.8) .150 (10.0) .394 (10.0) .394 Touch (2.54) Typ .100 8 CL (3.3) .130 (1.27) .050 (0.8 ~ 1.0) Dia Typ .031 ~ .039 Hexadecimal Right Angle PC • Plastic Shaft Accessories 3 45 23 901 FR01KC16H (10.0) .394 01 EF 2 (0.2) .008 89 67 A (10.0) .394 Decimal Hexadecimal CL (2.1) .083 (3.8) .150 (0.2) .008 (10.0) .394 (2.75) .108 1 BCD (10.0) .394 456 78 Indicators (3.8) .150 Supplement 4 Straight PC • Plastic Shaft (10.0) .394 G8 2 C 1 (10.0) .394 (0.2) .008 H CL (2.75) .108 89 67 A 89 67 A Programmable Illuminated PB Keylocks 901 Slides (3.8) .150 (0.2) .008 FR01FR10H P Hexadecimal (0.2) .008 1 (0.5) Typ .020 BCD G Decimal (10.0) .394 2 (3.8) .150 (10.0) .394 456 4 (3.3) .130 (3.8) Dia .150 Right Angle PC • Screwdriver (10.0) .394 8 C (10.0) .394 78 Rotaries 456 H (2.54) Typ .100 (7.62) .300 3 45 (3.8) Dia .150 FR01FC10P 01 EF 2 (10.0) .394 23 (10.0) .394 901 (0.2) Typ .008 (2.1) .083 (0.2) .008 01 EF 2 Rockers Straight PC • Screwdriver 89 67 A P www.nkk.com (7.0) .276 (0.2) Typ .008 (2.54) .100 (3.25) .128 2 4 (2.54) Typ .100 8 C C 1 2 4 8 (1.27) .050 (3.3) .130 (0.5) Typ .020 (2.54) Typ .100 (2.54) .100 (0.8 ~ 1.0) Dia Typ .031 ~ .039 Series FR01 Toggles 10mm DIP Rotaries TYPICAL SWITCH DIMENSIONS (3.4) .134 (10.0) .394 8 (7.62) .300 4 2 (2.54) Typ .100 2 4 8 1 (7.62) .300 C C (1.27) .050 (3.3) .130 (7.2) .284 Pushbuttons 1 (0.8 ~ 1.0) Dia Typ .031 ~ .039 (0.5) Typ .020 Hexadecimal FR01SR10P (0.4) Typ .016 (2.54) Typ .100 8 (11.0) .433 (7.62) .300 (11.6) .457 (13.1) .516 (2.28) .090 4 2 (6.1) .240 (0.2) Typ .008 C 4 8 (7.62) .300 C (1.27) .050 (12.7) .500 (0.5) Typ .020 (12.7) .500 (3.3) .130 (11.95) .470 2 1 M6 P0.75 (10.0) .394 (2.54) Typ .100 CL 1 (0.8 ~ 1.0) Dia Typ .031 ~ .039 G FR01AR10PB Shown in Position 0 with shaft flat rotated 180° from bushing flat Right Angle PC • Metal Shaft C 1 2 (5.5) .217 (2.28) .090 (11.6) .457 (13.1) .516 1 4 8 (10.0) .394 (7.62) .300 (13.9) .547 (0.2) Typ .008 (2.54) .100 (3.3) .130 (12.7) .500 2 4 8 (7.62) .300 C Flat (0.6) Typ .024 (3.03) .119 (6.1) .240 (2.54) Typ .100 CL Tilt (11.0) .433 (0.4) Typ .016 M6 P0.75 H (0.5) Typ .020 (2.54) Typ .100 Shown in Position 0 with shaft flat rotated 180° from bushing flat (1.27) .050 (12.7) .500 (2.54) .100 (0.8 ~ 1.0) Dia Typ .031 ~ .039 Touch (3.1) Dia .122 Slides (0.6) Typ .024 Flat Tactiles (3.1) Dia .122 P Keylocks Straight PC • Metal Shaft Indicators Decimal CL (2.54) Typ .100 Programmable Illuminated PB (9.8) Dia .386 (2.1) .083 (0.2) Typ .008 Rotaries (10.0) .394 123 4 5 67 (3.0) .118 (0.2) .008 P Rockers Straight PC • Dial Supplement Accessories FR01AC16HB www.nkk.com G9 Series FR01 Toggles 10mm DIP Rotaries PACKAGING Rockers S Pushbuttons FR01F, FR01K & FR01S Each stick-tube contains 50 switches. Switches must be ordered in 50-piece increments. Programmable Illuminated PB FR01A Each stick-tube contains 25 switches. Switches must be ordered in 25-piece increments. Note: Transport and storage temperatures should not exceed 50°C (122°F). Store stick tubes on flat surface. FR01F with Screwdriver Actuation & Straight PC Keylocks Rotaries Stick-Tube G FR01K with Plastic Shaft & Right Angle PC (16.6) .654 (15.9) .626 (15.6) .614 (540.0) 21.260 (530.0) 20.866 Slides (16.2) .638 (14.1) .555 (12.5) .492 Tilt Tactiles FR01S with Dial Actuation & Straight PC Touch FR01A with Metal Shaft & Straight PC FR01A with Metal Shaft & Right Angle PC (18.2) .717 (35.5) 1.398 (33.6) 1.323 Accessories Indicators (528.0) 20.787 Supplement (13.1) .516 G10 (390.0) 15.354 www.nkk.com (390.0) 15.354 Notes www.nkk.com G11