Ordering number : ENA2074 LA6681MC Monolithic Linear IC Single-phase Full-wave Fan Motor IC http://onsemi.com Overview The LA6681MC drives the single-phase bipolar fan motor, through low-saturation BTL output linear drive, silently and at high efficiency with suppressed reactive power while saving power. This product is the most suitable for the CPU cooler fan motor operating on 5V power for notebook PC, which is required to be compactness and low noise. Functions • Single-phase full-wave linear drive by BTL output. : Linear drive for further silence and the most suitable for fan motor for the notebook PC. • Operable at low voltage and over a wide operation voltage range (2.0 to 7.0V) • Low saturation output (Upper + lower saturation voltages: VOsat (total) = 0.32V typ, IO = 400mA) : High coil efficiency and small current drain. Small heat generation from IC itself • FG output (Rotation detection output: Open collector output) • High impedance of Hall input pin • Heat protection circuit : The heat protection circuit suppresses the drive current to prevent burn or damage of IC when the large current flows due to output short-circuit and the IC chip temperature exceeds 180°C. • Small package with high heat capacity Specifications Absolute Maximum Ratings at Ta = 25°C Parameter Supply voltage Symbol Conditions Ratings Unit VCC max 8 Output current IOUT max 1.0 A Output withstand voltage VOUT max 8 V FG output withstand voltage VFG max 8 V FG output current IFG max Allowable dissipation Pd max Operating temperature Topr Storage temperature Tstg Mounted on a specified board. *1 *2 V 5 mA 750 mW -30 to +110 °C -55 to +150 °C *1: Mounted on a specified board: 114.3×76.1×1.6 mm3, glass epoxy board. *2: Tjmax = 150°C max must not be exceeded. Caution 1) Absolute maximum ratings represent the value which cannot be exceeded for any length of time. Caution 2) Even when the device is used within the range of absolute maximum ratings, as a result of continuous usage under high temperature, high current, high voltage, or drastic temperature change, the reliability of the IC may be degraded. Please contact us for the further details. Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Semiconductor Components Industries, LLC, 2013 May, 2013 62012 SY 20120222-S00004 No.A2074-1/4 LA6681MC Recommended Operating Conditions at Ta = 25°C Parameter Symbol Conditions Ratings Unit Supply voltage VCC 2.0 to 7.0 V Common-phase input voltage VICM 0.3 to VCC–1.5 V range of Hall input Electrical Characteristics at Ta = 25°C, VCC = 5V, unless otherwise specified. Parameter Symbol Circuit current Ratings Conditions ICC min typ IN-=1.0V, IN+=2.0V, RL=∞ 14 19 0.25 V 0.30 V OUT saturation voltage L VOsatL IO = 400mA 0.17 OUT saturation voltage H VOsatH IO = 400mA 0.21 Input offset voltage VOFST Zero peak value Hall bias voltage VHB Hall amplifier gain Vg Hall amplifier input current VINR IHB = 5mA FG output L voltage VFG FG output leakage current IFGL VFG = 7V Overheat protection circuit Th 0 5 1.4 1.5 V 42 46 47 dB 150 * Design guarantee mA 1.3 mV -2 10 μA 0.2 0.3 V 30 μA 180 210 °C -10 IFG = 3mA Unit max Truth Table IN- IN+ OUT1 H L H L H L - - OFF OFF - OUT2 FG Mode L L During rotation H OFF Overheat protected -:Don’t care. Package Dimensions unit : mm (typ) 3424 4.9 8 0.2 Allowable power dissipation, Pd max -- W 0.835 0.375 6.0 3.9 0.42 1.75 MAX 1.27 2 Mounted on specified board: 114.3×76.1×1.6mm3 glass epoxy board. 0.8 0.6 0.4 0.24 0.2 0 -30 0.175 1 Pd max -- Ta 1.0 0 30 60 90 120 Ambient temperature, Ta -- °C SANYO : SOIC8 No.A2074-2/4 LA6681MC Pin Assignment IN+ 1 HB 2 8 FG 7 VCC LA6681MC IN- 3 6 OUT2 OUT1 4 5 GND Top View Block Diagram VCC FG 1.3V REG HB IN+ H IN- OUT1 OUT2 GND Timing chart Hall Signal OUTPUT Coil Current FG Pulse No.A2074-3/4 LA6681MC Application Circuit Examples *1 Di *4 Cr VCC HB R2 *2 H HB FG IN- OUT1 IN+ OUT2 *3 R2 H ININ+ GND Element in the board *1: When Di to prevent breakdown in case of reverse connection is used, it is necessary to insert a capacitor Cr to secure the regenerative current route. Similarly, Cr is necessary to enhance the reliability when there is no capacitor near the fan power line. *2: Basically, by taking the bias from HB 1.3V constant-output voltage, stable Hall and coil outputs can be obtained at high temperature. When taking the Hall bias from VCC, insert the limiting resistor R2 on the VCC side as shown in the figure, for biasing. (The use together with HB bias is recommended.) *3: Linear drive is made by amplifying the Hall output to perform voltage control of the coil. When the Hall element output is high, the starting performance and efficiency are improved. By adjusting (R3) the Hall element, the operation becomes more silent. *4: Keep this open when not using. ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PS No.A2074-4/4