PI49FCT805T PI49FCT2805T Fast CMOS Clock Driver/Buffer Features Description • • • • • • • • • Pericom Semiconductor’s PI49FCT805T and PI49FCT2805T are non-inverting clock drivers. Each clock driver consists of two banks of drivers, driving five outputs each from a standard TTL-compatible CMOS input. Extremely low output skew: 0.5ns Monitor output pin Clock busing with Hi-Z state control TTL input and CMOS output compatible Extremely low static power (1mW, typ.) Hysteresis on all inputs Device models available on request Industrial Operation at -40ºC to +85ºC Packaging (Pb-free & Green): – 20-pin 209-mil wide SSOP (H) – 20-pin 300-mil wide SOIC (S) – 20-pin 150-mil wide QSOP (Q) The PI49FCT2805T features a 25-Ohm on-chip resistor for lower noise. Block Diagram Pin Configuration VccA OA0 OA1 OA2 GNDA OA3 OA4 GNDB OEA INA OEA INA INB 5 5 OA0–4 OB0–4 OEB MON 10-0208 1 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 VccB OB0 OB1 OB2 GNDB OB3 OB4 MON OEB INB PS7007K 08/27/2010 PI49FCT805T PI49FCT2805T Fast CMOS Clock Driver/Buffer Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature................................................................ –65°C to +150°C Ambient Temperature with Power Applied.............................. –40°C to +85°C Supply Voltage to Ground Potential (Inputs & Vcc Only)......... –0.5V to +7.0V Supply Voltage to Ground Potential (Outputs & D/O Only)...... –0.5V to +7.0V DC Input Voltage........................................................................ –0.5V to +7.0V DC Output Current................................................................................... 120mA Power Dissipation....................................................................................... 0.5W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 5.0V ± 5%) Parameters Voh Description Output HIGH Voltage Vol Output LOW Current Vih Vil Iih Iil Iozh Iozl Ii Vik Ios Vh Input HIGH Voltage Input LOW Voltage Input HIGH Current Input LOW Current High Impedance Output Current Input HIGH Current Clamp Diode Voltage Short Circuit Current Input Hysteresis 10-0208 Test Conditions(1) Vcc = Min., Vin = Vih or Vil Vcc = Min., Vin = Vih or Vil Ioh = –24.0mA Iol = 64mA Iol = 12mA (25W) Guaranteed Logic HIGH Level Guaranteed Logic LOW Level Vcc = Max. Vin = Vcc Vcc = Max. Vin = GND Vcc = Max. Vout = Vcc Vout = GND Vcc = Max., Vin =Vcc (Max.) Vcc = Min., Iin = –18mA Vcc = Max.(3), Vout = GND Vcc = 5 V 2 Min. Typ(2) 2.4 3.3 0.3 0.3 Max. V 0.55 0.50 V V 0.8 1 –1 1 –1 20 –1.2 –225 V V µA µA µA µA µA V mA mV 2.0 –60 –0.7 –120 200 Units PS7007K 08/27/2010 PI49FCT805T PI49FCT2805T Fast CMOS Clock Driver/Buffer Capacitance Parameters CIN COUT Description Input Capacitance Output Capacitance Test Conditions VIN = 0V VOUT = 0V Typ 6 8 Max. 10 12 Units pF pF Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 5.0V, +25°C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. This parameter is determined by device characterization but is not production tested. Power Supply Characteristics Parameters Description Test Conditions Icc Quiescent Power Supply Current Supply Current per Input @ TTL HIGH Supply Current per Input per MHz(4) Vcc = Max. DIcc Iccd Ic Notes: 1. 2. 3. 4. 5. 6. Total Power Supply Current Min Vcc = Max. Vcc = Max., Outputs Open, OEa = OEb = GND, Per Output Toggling, 50% Duty Cycle Vcc = Max., Outputs Open fI = 10MHz 50% Duty Cycle OEA = OEB = GND Five Outputs Toggling Vcc = Max., Outputs Open fI = 10MHz 50% Duty Cycle OEA = OEB = GND Typ Max. Units 3 30 µA 0.5 2.0 mA 0.15 0.25 mA/ MHz Vin = Vcc, Vin = GND 7.7 8.0 14.05 15.05 mA Vin = 3.4V, Vin = GND 4.3 4.8 8.45 10.45 Vin = GND or Vcc Vin = 3.4V(3) Vin = Vcc, Vin = GND For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. Typical values are at Vcc = 5.0V, +25°C ambient. Per TTL driven input (Vin = 3.4V); all other inputs at Vcc or GND. This parameter is not directly testable, but is derived for use in Total Power Supply Calculations. Values for these conditions are examples of the Icc formula. These limits are guaranteed but not tested. Ic =Iquiescent + Iinputs + Idynamic Ic = Icc + DIcc DhNt + Iccd (fcp/2 + fiNi) Icc = Quiescent Current DIcc = Power Supply Current for a TTL High Input (Vin = 3.4V) Dh = Duty Cycle for TTL Inputs High Nt = Number of TTL Inputs at Dh Iccd = Dynamic Current Caused by an Input Transition Pair (HLH or LHL) fcp = Clock Frequency for Register Devices (Zero for Non-Register Devices) fi = Input Frequency Ni = Number of Inputs at fi All currents are in milliamps and all frequencies are in megahertz. 10-0208 3 PS7007K 08/27/2010 PI49FCT805T PI49FCT2805T Fast CMOS Clock Driver/Buffer Switching Characteristics over Operating Range Parameters Description Test Conditions(1) 805T/2805T 805AT 805BT 805CT Com. Min. Max. Com. Min. Max. Com. Min. Max. Com. Min. Max. 1.5 6.5 1.5 5.8 1.5 5.0 1.5 4.5 1.5 8.0 1.5 8.0 1.5 8.5 1.5 6.2 Output Disable Time(4) OEA to OAN, OEB to OBN Skew twx two outputs of CL = 50pF the same package RL = 500W (same transition) 1.5 7.0 1.5 7.0 1.5 6.0 1.5 5.0 _ 0.7 _ 0.5 _ 0.4 _ 0.4 tSKEW(p)(3) Skew twx two opposite transition (tPHL - tPLH) of same output _ 1.0 _ 0.7 _ 0.5 _ 0.5 tSKEW(t)(3) Skew twx two outputs of the different package at same temperature (same transition) _ 1.5 _ 1.0 _ 1.0 _ 1.0 Propagation Delay INA to OAN, INB to OBN Output Enable Time OEA to OAN, OEB to OBN tPLH tPHL tPZH tPZL tPHZ tPLZ tSKEW(o)(3) Units ns Notes: 1.See test circuit and wave forms. 2.Minimum limits are guaranteed but not tested on Propagation Delays. 3.Skew measured at worse cast temperature (max. temp). 4.This parameter is guaranteed but not production tested. Tests Circuits For All Outputs(1) Switch Position VCC 7.0V 500Ω Pulse Generator VIN VOUT 10-0208 50pF CL Switch Open Drain Enable LOW Disable LOW Closed All other inputs Open Definitions: CL = Load capacitance: includes jig and probe capacitance. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator. D.U.T. RT Test 500Ω 4 PS7007K 08/27/2010 PI49FCT805T PI49FCT2805T Fast CMOS Clock Driver/Buffer Switching Waveforms Propagation Delay Output Skew – tsk(o) 3V 3V Input Input 1.5V 1.5V tPLHx 0V tPHL tPLH VOH VOH Ox 1.5V 1.5V Output 0V tPHLx tSK(o) VOL tSK(o) Oy VOL VOH 1.5V tPLHy tPHLy VOL tSK(o) = | tPLHy – tPLHx | or | tPHLy – tPHLx | Enable and Disable Times Pulse Skew – tsk(p) Enable Disable 3V OE 3V Input 1.5V tPZL Output Normally Low Switch Closed 3.5V 0.3V tPHZ Switch Open tPLH 3.5V 1.5V tPZH Output Normally High 0V tPLZ 0.3V 1.5V 0V 1.5V tPHL Output 0V VOH 1.5V VOL VOL VOH tSK(p) = | tPHL – tPLH | 0V Package Skew – tsk(t) 3V Input 1.5V tPLH1 0V tPHL1 VOH Package 1 Output 1.5V tSK(t) tSK(t) Package 2 Output VOL VOH 1.5V tPLH2 tPHL2 VOL tSK(t) = | tPLH2 – tPLH1 | or | tPHL2 – tPHL1 | 10-0208 5 PS7007K 08/27/2010 PI49FCT805T PI49FCT2805T Fast CMOS Clock Driver/Buffer Packaging Mechanical: 20-pin SSOP (H20) 1 DATE: 04/10/08 DESCRIPTION: 20-Pin, 209-Mil Wide, SSOP PACKAGE CODE: H20 DOCUMENT CONTROL #: PD-1240 REVISION: E 08-0140 Note: • For latest package info, please check: http://www.pericom.com/products/packaging/mechanicals.php 10-0208 6 PS7007K 08/27/2010 PI49FCT805T PI49FCT2805T Fast CMOS Clock Driver/Buffer Packaging Mechanical: 20-pin QSOP (Q20) DOCUMENT CONTROL NO. PD - 1202 20 REVISION: H .008 0.20 MIN. .150 .157 3.81 3.99 Guage Plane .010 0.254 1 .041 1.04 REF .015 x 45˚ 0.38 .053 1.35 .069 1.75 Detail A 1 SEATING PLANE .025 BSC 0.635 0˚-6˚ .016 .035 0.41 0.89 Detail A .337 8.56 .344 8.74 .058 REF 1.47 DATE: 10/22/07 .008 .013 0.20 0.33 .008 0.203 .012 0.305 .004 0.101 .010 0.254 .007 .010 0.178 0.254 .228 .244 5.79 6.19 X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS Pericom Semiconductor Corporation 3545 N. 1st Street, San Jose, CA 95134 1-800-435-2335 • www.pericom.com Note: 1) Controlling dimensions in inches. 2) Ref: JEDEC MO-137B/AD 3) Dimensions do not include mold flash, protrusions or gate burrs DESCRIPTION: 20-Pin, 150-Mil Wide, QSOP PACKAGE CODE: Q Note: • For latest package info, please check: http://www.pericom.com/products/packaging/mechanicals.php 10-0208 7 PS7007K 08/27/2010 PI49FCT805T PI49FCT2805T Fast CMOS Clock Driver/Buffer Packaging Mechanical: 20-pin SPIC (S20) DOCUMENT CONTROL NO. PD - 1006 20 REVISION: D .2914 .2992 DATE: 03/09/05 7.40 7.60 .010 .029 0.254 x 45˚ 0.737 1 .496 12.60 .511 12.99 .020 0.508 REF .030 0.762 0.23 0.32 0.41 .016 1.27 .050 1 .0926 .1043 2.35 2.65 SEATING PLANE .050 BSC 1.27 .0091 .0125 0-8˚ .013 .020 0.33 0.51 .0040 .0118 .394 .419 10.00 10.65 0.10 0.30 X.XX DENOTES CONTROLLING X.XX DIMENSIONS IN MILLIMETERS Pericom Semiconductor Corporation 3545 N. 1st Street, San Jose, CA 95134 1-800-435-2335 • www.pericom.com Notes: 1) Controlling dimensions in millimeters. 2) Ref: JEDEC MS-013D/AC DESCRIPTION: 20-Pin, 300-Mil Wide, SOIC PACKAGE CODE: S Note: • For latest package info, please check: http://www.pericom.com/products/packaging/mechanicals.php 10-0208 8 PS7007K 08/27/2010 PI49FCT805T PI49FCT2805T Fast CMOS Clock Driver/Buffer Ordering Information(1-3) Ordering Code Package Code Speed Grade PI49FCT805TQE Q Blank Pb-free & Green, 20-pin 150-mil QSOP PI49FCT805ATSE S A Pb-free & Green, 20pin 300-mil SOIC PI49FCT805CTHE H C Pb-free & Green, 20-pin 209-mil SOIC PI49FCT805CTQE Q C Pb-free & Green, 20-pin 150-mil QSOP Package Type Notes: 1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ 2. E = Pb-free and Green 3. Adding an X suffix = Tape/Reel Ordering Information for PI49FCT2805T Ordering Code Package Code Speed Grade PI49FCT2805TSE S Blank Pb-free & Green, 20-pin 300-mil SOIC PI49FCT2805TQE Q Blank Pb-free & Green, 20-pin 150-mil QSOP Package Type Notes: 1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ 2. E = Pb-free and Green 3. Adding an X suffix = Tape/Reel Pericom Semiconductor Corporation • 1-800-435-2336 • www.pericom.com 10-0208 9 PS7007K 08/27/2010