Datasheet

PI3VDP612
High Bandwidth 6-differential Channel, 1:2 Demux
for DisplayPortTM rev 1.1a Signal Switching
Features
Description
• 4 Differential Channel, 1:2 DeMux that will support
2.7Gbps DP rev 1.1a signals
• 1-channel 1:2 demux for DP_HPD signal
• 1-differential channel 1:2 demux for DP_Aux signal
• Insertion Loss for high speed channels @ 2.7 Gbps: -1.5dB
• Hot Insertion Cable
• -3dB Bandwith for high speed channels of 3.25 Ghz
• Low Bit-to-Bit Skew , 7ps max (between '+' and '-' bits)
• Low Crosstalk for high speed channels: [email protected] Gbps
• Low Off Isolation for high speed channels: [email protected] Gbps
• VDD Operating Range: 3.3V +/-10%
• ESD Tolerance: 8kV contact on all data I/O pins per IEC61000-4-2 Specification
• Low channel-to-channel skew, 35ps max
• Packaging (Pb-free & Green):
-42 TQFN (ZHE)
Pericom Semiconductor’s PI3VDP612, one to two Demux is
targeted for next generation digital video signals. This device
can be used to connect a Display Port Source to two Independent
Display Port Sinks.
The newly released Display Port spec requires a data rate of
2.7 Gbps with AC coupled I/Os. Pericom's solution has been
specifically designed around this standard and will support such
signals.
Block Diagram
Pin Description - 42-Pin
LE
SEL
11-0002
Logic
Control
1
D1- A
VDD
40
39
D0-A
D1+ A
41
35
5
34
6
33
7
32
GND
8
31
9
30
10
29
11
28
12
27
13
26
14
25
15
24
16
23
17
22
AUX+B
SEL
LE
AUX+ B
AUX- B
HPD B
CAB_DETB/LEDB
36
4
D2+A
D2-A
D3+A
D3-A
D0+B
D0-B
D1+B
D1-B
D2+B
D2-B
D3+B
D3-B
VDD
AUX+A
AUX-A
HPD_ A
CAB_DETA/LED_A
21
AUX+ A
AUX- A
HPD A
CAB_DETA/LEDA
3
20
AUX+
AUXHPD
CAB_DET/LED
AUX+
AUXHPD
CAB_DET/LED
VDD
37
AUX-B
D2+B
D2-B
D3+B
D3-B
38
2
16
D0+B
D0-B
D1+B
D1-B
1
18
D0+A
D0+
D0D1+
D1VDD
D2+
D2D3+
D3-
D2+A
D2-A
D3+A
D3-A
HPD_B
D2+
D2D3+
D3-
42
D0+A
D0-A
D1+A
D1-A
CAB_DETB/LED_B
D0+
D0 D1+
D1 -
Application
Routing of Display Port signals with low signal attenuation between notebook DP connector and docking station DP connector.
PS8928D
11/03/10
PI3VDP612
High Bandwidth 6-differential channel, 1:2 Demux
for DisplayPortTM rev 1.1a Signal Switching
Pin Description
Pin #
Pin Name
Signal Type
Description
GND
Power
Ground
2
D0+
I/O
Positive Lane0 signal for common port
3
D0-
I/O
Negative Lane0 signal for common port
4
D1+
I/O
Positive Lane1 signal for common port
5
D1-
I/O
Negative Lane1 signal for common port
6
VDD
Power
3.3V Power Supply
7
D2+
I/O
Positive Lane2 signal for common port
8
D2-
I/O
Negative Lane2 signal for common port
9
D3+
I/O
Positive Lane3 signal for common port
10
D3-
I/O
Negative Lane3 signal for common port
GND
Power
Ground
11
AUX+
I/O
Positive AUX signal for common port
12
AUX-
I/O
Negative AUX signal for common port
13
HPD
I/O
HPD for common port
14
CAB_DET/LED
I/O
common port pin13 from dual mode DP connector or LED common
port
GND
Power
Ground
15
VDD
Power
3.3V Power Supply
16
SEL
Input
Port Selection Control. If LOW, then port A is active. If HIGH, then
port B is active
17
LE
Input
Latch Control. If LOW, then SEL pin will control port selection. If
HIGH, then controllability is Latched.
GND
Power
Ground
GND
Power
Ground
VDD
Power
3.3V Power Supply
18
CAB_DETB/LEDB
I/O
PortB pin13 from dual mode DP connector or LED from port B
19
HPD_B
I/O
HPD for port B
20
AUX-B
I/O
Negative AUX signal for Port B
21
AUX+B
I/O
Positive AUX signal for Port B
VDD
Power
3.3V Power Supply
GND
Power
Ground
GND
Power
Ground
22
CAB_DETA/LEDA
I/O
PortA pin13 from dual mode DP connector or LED from port A
23
HPD_A
I/O
HPD for port A
24
AUX-A
I/O
Negative AUX signal for Port A
25
AUX+A
I/O
Positive AUX signal for Port A
(Continued)
11-0002
2
PS8928D
11/03/10
PI3VDP612
High Bandwidth 6-differential channel, 1:2 Demux
for DisplayPortTM rev 1.1a Signal Switching
Pin #
Pin Name
Signal Type
Description
26
VDD
Power
3.3V Power Supply
GND
Power
Ground
27
D3-B
I/O
Negative Lane3 signal for Port B
28
D3+B
I/O
Positive Lane3 signal for Port B
29
D2-B
I/O
Negative Lane2 signal for Port B
30
D2+B
I/O
Positive Lane2 signal for Port B
31
D1-B
I/O
Negative Lane1 signal for Port B
32
D1+B
I/O
Positive Lane1 signal for Port B
33
D0-B
I/O
Negative Lane0 signal for Port B
34
D0+B
I/O
Positive Lane0 signal for Port B
35
D3-A
I/O
Negative Lane3 signal for Port A
36
D3+A
I/O
Positive Lane3 signal for Port A
37
D2-A
I/O
Negative Lane2 signal for Port A
38
D2+A
I/O
Positive Lane2 signal for Port A
GND
Power
Ground
GND
Power
Ground
39
VDD
Power
3.3V Power Supply
40
D1-A
I/O
Negative Lane1 signal for Port A
41
D1+A
I/O
Positive Lane1 signal for Port A
42
D0-A
I/O
Negative Lane0 signal for Port A
1
D0+A
I/O
Positive Lane0 signal for Port B
VDD
Power
3.3V Power Supply
GND
Power
Ground
11-0002
3
PS8928D
11/03/10
PI3VDP612
High Bandwidth 6-differential channel, 1:2 Demux
for DisplayPortTM rev 1.1a Signal Switching
Truth Table (SEL control)
Truth Table (Latch control)
Function
SEL
LE
SEL
Port A is active
L
0
Responds to changes on SEL
Port B is active
H
1
Latched
Application Example for single mode DP support
Min Vswing
0V
Vbias_Tx
DISPLAY
PORT TX
+
-
50
Ω
+
-
5-Differential
PI3VDP612
HPD
50
Ω
Note: if the Max Vswing (in single-ended mode) of the signals to
PI3VDP612 exceeds 1.2V, then AC coupling capacitors are needed
between the 50ohm terminations and PI3VDP612.
HPD
LED
Driver
1-Differential (Aux)
HPD
1.2V Max Vswing
1-Differential (Aux)
VDD
DISPLAY
PORT
4-Differential
LED
4-Differential
Notebook
DOCKING
CONNECTOR
GND/3.3V
100kΩ
x2
GND/3.3V
100kΩ
x2
LED
Application Example for Dual Mode Display Port Support
PI3VDP612
Intel Chipset
Dual Mode DP #1
Dual Mode DP
CAB_DET1
AUX/DDC #1
DDC
Driver
AUX/DDC
AUX
Driver
CAB_DET
CAB_DET2
Dual Mode DP #2
PI3C3306
11-0002
Dual
Mode
DP
1Mohm
Dual
Mode
DP
AUX/DDC #2
4
PS8928D
11/03/10
PI3VDP612
High Bandwidth 6-differential channel, 1:2 Demux
for DisplayPortTM rev 1.1a Signal Switching
Maximum Ratings
(Above which useful life may be impaired. For user guidelines, not tested.)
Storage Temperature .....................................................–65°C to +150°C
Supply Voltage to Ground Potential ................................–0.5V to +3.6V
DC Input Voltage ............................................................... –0.7V to 3.6V
DC Output Current ....................................................................... 120mA
Power Dissipation ............................................................................ 0.5W
Note: Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the device. This
is a stress rating only and functional operation of the device
at these or any other conditions above those indicated in the
operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended
periods may affect reliability.
DC Electrical Characteristics for Switching over Operating Range (TA = –40°C to +85°C, VDD =
3.3V +/-10%)
Paramenter
Description
Test Conditions(1)
Min
Typ(2)
VIH
Input HIGH Voltage
Guaranteed HIGH level
1.6
VIL
Input LOW Voltage
Guaranteed LOW level
VIK
Clamp Diode Voltage
VDD = Max., IIN = –18mA
IIH
Input HIGH Current
VDD = Max., VIN = VDD
±5
IIL
Input LOW Current
VDD = Max., VIN = GND
±5
RON
On resistance between input
to output
VDD = 3.0V, -0.6V<VINPUT<0.6V
7
Ohm
VDD = 3.0V, 1.0V<VINPUT<1.5V
10
Ohm
–0.7
Max
Units
0.75
V
–1.2
µA
Power Supply Characteristics
Parameters
Description
ICC
Quiescent Power Supply Current
Test Conditions(1)
VDD = Max., VIN = GND or VDD
Min.
Typ.(2)
Max.
Units
40
100
µA
Dynamic Electrical Characteristics Over the Operating Range (TA= -40º to +85ºC, VDD = 3.3V
+/-10%, GND=0V)
Typ.(2)
Parameter
Description
Test Conditions
XTALK
Crosstalk on High Speed Channels
See Fig. 1 for Measurement
Setup
OIRR
OFF Isolation on High Speed Channels
See Fig. 2 for Measurement
Setup,
ILOSS
Differential Insertion Loss on High
Speed Channels
@2.7Gbps (see figure 3)
-1.5
dB
BW_Dx±
Bandwidth -3dB for Main high speed
path (Dx±)
See figure 3
3.25
GHz
BW_AUX/HPD
-3dB BW for AUX and HPD signals
See figure 3
1.5
GHz
f= 1.35 GHz
-33dB
f = 100 MHz
-48dB
f= 1.35 GHz
-33dB
f = 100 MHz
-56dB
Units
dB
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VDD = 3.3V, Ta = 25°C ambient and maximum loading.
11-0002
5
PS8928D
11/03/10
PI3VDP612
High Bandwidth 6-differential channel, 1:2 Demux
for DisplayPortTM rev 1.1a Signal Switching
BALANCED
PORT1
BALANCED
PORT2
+
+
50
–
–
50
+
+
50
–
–
50
DUT
Fig 1. Crosstalk Setup
BALANCED
PORT1
+
+
50
–
–
50
+
BALANCED
PORT2
–
DUT
Fig 2. Off-isolation setup
BALANCED
PORT1
+
+
–
–
BALANCED
PORT2
DUT
Fig 3. Differential Insertion Loss
11-0002
6
PS8928D
11/03/10
PI3VDP612
High Bandwidth 6-differential channel, 1:2 Demux
for DisplayPortTM rev 1.1a Signal Switching
Fig 4. Crosstalk
11-0002
7
PS8928D
11/03/10
PI3VDP612
High Bandwidth 6-differential channel, 1:2 Demux
for DisplayPortTM rev 1.1a Signal Switching
Fig 5. Off Isolation
11-0002
8
PS8928D
11/03/10
PI3VDP612
High Bandwidth 6-differential channel, 1:2 Demux
for DisplayPortTM rev 1.1a Signal Switching
Fig 6. Insertion Loss
11-0002
9
PS8928D
11/03/10
PI3VDP612
High Bandwidth 6-differential channel, 1:2 Demux
for DisplayPortTM rev 1.1a Signal Switching
Fig 7. Ron Curve for high speed signal path only (Dx+/-)
11-0002
10
PS8928D
11/03/10
PI3VDP612
High Bandwidth 6-differential channel, 1:2 Demux
for DisplayPortTM rev 1.1a Signal Switching
Switching Characteristics (TA= -40º to +85ºC, VDD = 3.3V±10%)
Paramenter
Description
Min.
Max.
Units
tPZH, tPZL
Line Enable Time
0.5
15.0
tPHZ , tPLZ
Line Disable Time
0.5
15.0
Tpd
Propagation delay (input pin to output pin)
200
ps
tb-b
Bit-to-bit skew within the same differential pair
7
ps
tch-ch
Channel-to-channel skew
50
ps
ns
Test Circuit for Electrical Characteristics(1-5)
6.0V
VDD
200-ohm
Pulse
Generator
VIN
D.U.T
VOUT
4pF
CL
RT
200-ohm
Notes:
1. CL = Load capacitance: includes jig and probe capacitance.
2. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator
3. Output 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
output 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
4. All input impulses are supplied by generators having the following characteristics: PRR ≤ MHz, ZO = 50Ω, t R ≤ 2.5ns, t F ≤ 2.5ns.
5. The outputs are measured one at a time with one transition per measurement.
Switching Waveforms
SEL
VDD/2
VDD/2
VDD
0V
Output 1
tPZL
tPLZ
VDD/2
VOH
VOL + 0.3V
tPHZ
tPZH
VOH – 0.3V
VDD/2
VOL
VOH
VOL
Output 2
Voltage Waveforms Enable and Disable Times
Switch Positions
Test
Switch
tPLZ , tPZL (output on B-side)
6.0V
tPHZ , tPZH (output on B-side)
GND
Prop Delay
Open
11-0002
11
PS8928D
11/03/10
PI3VDP612
High Bandwidth 6-differential channel, 1:2 Demux
for DisplayPortTM rev 1.1a Signal Switching
Test Circuit for Dynamic Electrical Characteristics
Agilent N5230A 300kHz-20GHz PNA-L Network Analyzer
PI3VDP612
HP11667A
Application Section
Pre-emphasis waveforms
Input Pre-emphasis = 9.5dB; Red waveform is input of PI3VDP612 and Black is output of PI3VDP612
11-0002
12
PS8928D
11/03/10
PI3VDP612
High Bandwidth 6-differential channel, 1:2 Demux
for DisplayPortTM rev 1.1a Signal Switching
Input Pre-emphasis = 6dB; Red waveform is input of PI3VDP612 and Black is output of PI3VDP612
11-0002
13
PS8928D
11/03/10
PI3VDP612
High Bandwidth 6-differential channel, 1:2 Demux
for DisplayPortTM rev 1.1a Signal Switching
Input Pre-emphasis = 3.5dB; Red waveform is input of PI3VDP612 and Black is output of PI3VDP612
11-0002
14
PS8928D
11/03/10
PI3VDP612
High Bandwidth 6-differential channel, 1:2 Demux
for DisplayPortTM rev 1.1a Signal Switching
Packaging Mechanical: 42-Pin TQFN (ZH)
1
DATE: 02/17/09
Notes:
1. All dimensions are in millimeters, angles in degrees.
2. Coplanarity applies to the exposed thermal pad as well as the terminals.
3. Refer JEDEC MO-220
4. Recommended Land Pattern is for reference only.
5. Thermal Pad Soldering Area
DESCRIPTION: 42-contact Thin Fine Pitch Quad Flat No-Lead (TQFN)
PACKAGE CODE: ZH (ZH42)
REVISION: C
DOCUMENT CONTROL #: PD-2035
09-0116
Ordering Information
Ordering Code
Package Code
Package Description
PI3VDP612ZHE
ZH
Pb-free & Green, 42-contact TQFN
Notes:
• Thermal characteristics can be found on the company web site at www.pericom.com/packaging/
• "E" denotes Pb-free and Green
• Adding an "X" at the end of the ordering code denotes tape and reel packaging
Pericom Semiconductor Corporation • 1-800-435-2336 • www.pericom.com
11-0002
15
PS8928D
11/03/10