TABLE 1: ELECTRICAL SPECIFICATIONS AT 25 OC FIGURE 1: SCHEMATIC DIAGRAM SWITCHING TRANSFORMER DESIGNED FOR USE WITH POWER INTEGRATIONS PWR-TOP214YAI. REFER TO APPLICATION CIRCUIT OF FIGURE 3. PARAMETER MIN. SPEC LIMITS TYP. PRIMARY INDUCTANCE (2-1) VOLTAGE = 0.250Vrms FREQUENCY = 100 KHZ 486 540 PRI LEAKAGE IND. (SEC'S SHORT) 0.250Vrms @ 100KHz APP CIRCUIT PARAMETERS: (1) AC LINE VOLTAGE 47/400 Hz SEC #1 OUTPUT VOLTAGE SEC #1 OUTPUT mA CONTINUOUS SEC #1 LOAD REGULATION 10-100% SEC #2 OUTPUT VOLTAGE (2) SEC #2 OUTPUT mA CONTINUOUS SEC #2 LOAD REGULATION 10-100% LINE REGULATION (85 TO 265Vac) RIPPLE EACH OUTPUT TRANSFORMER TEMPERATURE RISE 6 594 µHY 1 ---------------------- 1: 2.17 1:14.29 1: 6.25 -------- 15.0 ---------------------- + 3% + 3% + 3% 25.0 µHY 1 2 3000 1500 --------------- --------------- Vrms Vrms 85 28.0 20 -------- -------30.0 -------8.0 (3) 5.0 -------0.50 0.20 100.0 20.0 265 Vac Vdc mA +% Vdc mA +% +% +mV O C 200 ----------------------------- 2 7 3 6 500 -------1000 ----------------------------- 5 NOTE1: DESIGNED TO MEET UL1950, IEC950, & CSA-950 REQUIREMENTS: A) ALL MATERIALS MEET "UL", "CSA" & "IEC" REQUIREMENTS B) MARGIN WOUND FOR >6.2mm CREEPAGE REQUIREMENTS. C)VARNISH FINISHED ASSEMBLY. D)130 (B) INSULATION SYSTEM PM130-N1, PM130-P1, TABLE II (UL #E177139) (1) REFER TO APPLICATION CIRCUIT OF FIGURE 3. (2) SEC #2 IS REGULATED OUTPUT. (3) SEC #1 IS INTENDED TO FEED A 24V LINEAR REGULATOR 4 CORE TAPED 18.00 (.709) MAX .157 (4.0) MIN MYLAR TAPE 7mm WIDE 31.24 (1.23) MAX 2 SECONDARY #1 NOTE2: A) BOTTOM HALF OF CORE IS CUFF WRAPPED PRIOR TO ASSEMBLY. THIS GAURANTEES 6.2mm CREEPAGE PIN-CORE-PIN 23.00 (.906) MAX 1 SECONDARY #2 FIGURE 2: PHYSICAL DIMENSIONS mm (INCHES) 5 3 8 BIAS P TSD-988 M YYWW PIN #1 WHITE DOT WHITE DOT DENOTES PIN #1 4 HIPOT: PRIMARY & BIAS TO SECONDARY'S SECONDARY #1 TO SECONDARY #2 7 UNITS PRIMARY TURN RATIO'S: SEC #1 (6-5) : PRIMARY (2-1) SEC #2 (8-7) : PRIMARY (2-1) BIAS (3-4) : PRIMARY (2-1) 8 MAX. 3 5.00 (.197) CUFF WRAP BOTTOM HALF OF CORE UL INSULATION SYMBOL AND MANUFACTURER IDENTIFICATION HERE 0.8 DIA. (.032) 4 4.0 (.157) MIN 12.50 (.492) BOTTOM HALF OF CORE IS CUFF WRAPPED WITH MYLAR TO GUARANTEE 6.2mm PIN-CORE-PIN CREEPAGE REV. 02/11/98 03/17/98 03/24/98 04/26/99 DESCRIPTION OF CHANGES COMPLETLEY REVISED TO MAXIMIZE PRIMARY IND. IN TOP226 APP. INCREASED TURNS SEC #1 (+3T) & BIAS +2T INCREASE SEC#1 TURNS UPDATE TO UL CLASS (B) 130 INSULATION SYSTEM TO TO TO TO MD EE22/29/6, 8-PIN VERTICAL BOBBIN P Premier M Magnetics Inc. UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MM DIMENSIONAL TOLERANCES ARE: DECIMALS ANGLES .X + .25 +0 O 30' .XX + .15 DO NOT SCALE DRAWING FLYBACK TRANSFORMER CONTROL DRAWING PREMIER P/N: TSD-988 REVISION: 04/26/99 DRAWN BY: TOM O'NEIL REF: TOP214/TOP226 SCALE: NONE SHEET: 1 OF 4 APPLICATION NOTES Premier Magnetic's TSD-988 Switch Mode Transformer was designed for use with Power Integrations, Inc. TOP214Y or TOP226Y three terminal off-line PWM switching regulator in the Flyback Buck-Boost circuit configuration. This conversion topology can provide isolated multiple outputs with efficiencies up to 90%. Premier's TSD-983 transformer has been optimized to provide maximum power throughput. The PWR-TOPXXX series from Power Integrations, Inc. are self contained 100KHz three terminal voltage controlled PWM switching regulators. This series contains all necessary functions for an off-line switched mode control DC power source. These switching regulators provide a very simple solution to off-line designs. The inductors and transformer used with the PWR-TOPXXX are critical to the performance of the circuit. They define the overall efficiency, output power and overall physical size. Below is a universal input Dual Output 19 watt application circuit utilizing Power Integrations PWR-TOP214YAI switching regulator in the flyback buck-boost configuration. The component values listed are intended for reference purposes only. The 27.5V output is intended to feed a 24V linear regulator. FIGURE 3: TYPICAL APPLICATION CIRCUIT F1 3.15A LINE 1 L1 PMCU-0100 10mHY ~ 2 +71 to 375Vdc + C1 47 uF 400V C6 0.1uF 4 NEUT 3 ~ T1 TSD-988 5 + 85-265Vac 50/60Hz BR1 DF06M 600V, 1.0A EMI FILTER 27.5V_RTN - C11 100uF + 50V C6 = 0.1uF 250Vac X2-Saftey Cap L3 VTP-01001 SEC#1 CLAMP NETWORK 6 1 VR1 P6KE200A 5 MOC8101 8 C4 0.1uF PROPERLY SIZED HEAT SINK SOURCE D2 MBR360 C5 47uF C R1 510 KELVIN CONNECT C10 0.1uF +5Vdc @ 1.0A R2 200 1/2W 2 R1 6.2 CONTROL + A 4 E R4 10.0K 1% 1 4 + DRAIN 1/2 OF U3 L2 VTP-01001 C3 220uF 16V 1/2 OF U3 MOC8101 BIAS U1 POWER INT. PWR-TOP214YAI 5V_RTN R5 10.0K 1% SEC #2 3 C +27.5Vdc @ 500mA D2 MUR120 C2 1000uF + 25V 2 D2 1N4148 U3 + 7 PRI D1 MUR160 C12 100uF 50V C7 & C8 = 250Vac Y-SAFTEY CAPACITORS EMI FILTER C7 2.2nF C8 2.2nF 1 U2 C TL431 R A C9 0.1uF 8 6 HIGH VOLTAGE RETURN P Premier M Magnetics Inc. UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MM DIMENSIONAL TOLERANCES ARE: DECIMALS ANGLES .X + .25 +0 O 30' .XX + .15 DO NOT SCALE DRAWING FLYBACK TRANSFORMER CONTROL DRAWING PREMIER P/N: TSD-988 REVISION: 04/26/99 DRAWN BY: TOM O'NEIL REF: TOP214/TOP226 SCALE: NONE SHEET: 2 OF 4