SS2406 Hall Latch - High Sensitivity Packages Features and Benefits – 3 pin SOT23 (suffix SO) – – – – – – – – 3 pin SIP (suffix UA) Functional Block Diagram Application Examples VDD Voltage Regulator Wide operating voltage range from 2.5V to 24V High magnetic sensitivity – Multi-purpose DMOS technology Low current consumption Chopper-stabilized amplifier stage Open drain output Superior temperature stability Insensitive to physical stress SOT23 3L and flat SIP 3L both RoHS Compliant packages OUT Chopper – – – – – – – Automotive, Consumer and Industrial Solid-state switch Brushless DC motor commutation Speed detection Angular position detection Linear position detection Proximity detection Hall Plate General Description GND SIP Package Pin 1 – VDD Pin 2 – GND Pin 3 – OUT The SS2406 is a Hall-effect sensor IC fabricated from mixed signal DMOS technology. The device integrates a voltage regulator, Hall sensor with dynamic offset cancellation system, Schmitt trigger and an open-drain output driver, all in a single package. SOT Package Pin 1 – VDD Pin 2 – OUT Pin 3 – GND It incorporates advanced chopper stabilization techniques to provide accurate and stable magnetic switch points. There are many applications for this HED - Hall Electronic Device - in addition to those listed above. The design, specifications and performance have been optimized for commutation applications in 5V and 12V brushless DC motors. Thanks to its wide operating voltage range and extended choice of temperature range, it is quite suitable for use in automotive, industrial and consumer applications. The device is delivered in a Small Outline Transistor (SOT) for surface mount process or in a Plastic Single In Line (TO92) for through- hole mount. Both 3-lead packages are RoHS compliant. 1 V3.10 Nov 1, 2013 SS2406 Hall Latch - High Sensitivity Glossary of Terms MilliTesla (mT), Gauss RoHS SOT ESD BLDC Operating Point (BOP) Release Point (BRP) Units of magnetic flux density: 1mT = 10 Gauss Restriction of Hazardous Substances Small Outline Transistor (SOT package) – also referred with the package code “SO” Electro-Static Discharge Brush-Less Direct-Current Magnetic flux density applied on the branded side of the package which turns the output driver ON (VOUT = VDSon) Magnetic flux density applied on the branded side of the package which turns the output driver OFF (VOUT = high) Unique Features Based on mixed signal DMOS technology, the SS2406 is a Hall-effect device with high magnetic sensitivity. This multi-purpose latch meets most of the application requirements. The chopper-stabilized amplifier uses switched capacitor technique to suppress the offset generally observed with Hall sensors and amplifiers. The DMOS technology makes this advanced technique possible and contributes to smaller chip size and lower current consumption than bipolar technology. The small chip size is also an important factor to minimize the effect of physical stress. This combination results in more stable magnetic characteristics and enables faster and more precise design. The wide operating voltage from 3.5V to 24V, low current consumption and large choice of operating temperature range according to “E”, “K” and “L” specification make this device suitable for automotive, industrial and consumer applications. Pin Definitions and Descriptions SOT Pin № SIP Pin № 1 2 3 1 3 2 Name Type Function VDD OUT GND Supply Output Ground Supply Voltage Pin Open Drain Output Pin Ground Pin 2 V3.10 Nov 1, 2013 SS2406 Hall Latch - High Sensitivity Absolute Maximum Ratings Parameter Supply Voltage Supply Current Output Voltage Output Current Storage Temperature Range Maximum Junction Temperature Symbol VDD IDD VOUT IOUT TS TJ Value 28 50 28 50 -65 to 150 165 Units V mA V mA °C °C Operating Temperature Range Temperature Suffix “E” Temperature Suffix “K” Temperature Suffix “L” Symbol TA TA TA Value -40 to 85 -40 to 125 -40 to 150 Units °C °C °C Exceeding the absolute maximum ratings may cause permanent damage. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. General Electrical Specifications DC Operating Parameters TA = 25°C, VDD= 2.5V to 24V (unless otherwise specified) Parameter Symbol Supply Voltage Supply Current Output Saturation Voltage Output Leakage Current Output Rise Time Output Fall Time Maximum Switching Frequency Electro-Static Discharge Package Thermal Resistance VDD IDD VDSon IOFF tr tf FSW HBM RTH Test Conditions Min Operating B < BRP IOUT = 20mA, B > BOP B < BRP VOUT = 24V RL = 1kΩ, CL = 20pF RL = 1kΩ, CL = 20pF ----Single layer (1S) Jedec board 2.5 Typ 1 0.04 0.18 10 Max Units 24 5 0.4 10 0.45 0.45 V mA V µA µs µs KHz KV °C/W 4 301 Note: The output of SS2406 will be switched after the supply voltage is over 2.2V, but the magnetic characteristics will not be normal until the supply is over 2.5V. Magnetic Specifications DC Operating Parameters TA = 25°C, VDD =12V (unless otherwise specified) Package Parameter Symbol Operating Point BOP Test Conditions Min Typ Max Units 5 15 25 G -25 -15 -5 G Ta=25°C UA Release Point BRP Hysteresis BHYST Operating Point BOP Vdd=5V DC 30 G -25 -15 -5 G 5 15 25 G Ta=25°C SO Release Point Hysteresis BRP Vdd=5V DC BHYST 30 3 G V3.10 Nov 1, 2013 SS2406 Hall Latch - High Sensitivity Output Behavior versus Magnetic Pole DC Operating Parameters TA = -40°C to 150°C, VDD = 2.5 to 24V (unless otherwise specified) Test Conditions (UA) Test Conditions (SO) OUT B < BRP B > BRP High B > BOP B < BOP Low The SOT-23 device is reversed from the UA package. The SOT-23 output transistor will be turned on(drops low) in the presence of a sufficiently strong North pole magnetic field applied to the marked face and turned off(hoists high) in the presence of a sufficiently strong South pole magnetic field. Detailed General Description The SS2406 exhibits latch magnetic switching characteristics. Therefore, it requires both south and north poles to operate properly. The OUT pin of these devices switches low (turns on) when a magnetic field perpendicular to the Hall sensor exceeds the operate point threshold, BOP. After turn-on, the output voltage is VDSon. Note that the device latches, that is, a south pole of sufficient strength towards the branded surface of the device turns the device on. The device remains on if the south pole is removed (B→0). This latching property defines the device as a magnetic memory. When the magnetic field is reduced below the release point, BRP, the OUT pin turns off (goes high). The difference in the magnetic operating and release points is the hysteresis, BHYST, of the device. This built-in hysteresis prevents output oscillation near the switching point, and allows clean switching of the output even in the presence of external mechanical vibration and electrical noise. The device behaves as a latch with symmetric operating and release switching points (BOP=|BRP|). This means magOutput level Output level OUT = High OUT = High BHYS BHYS OUT = Low OUT = Low BRP -15Gs typ 0mT BOP 15Gs typ BRP -15Gs typ Flux density UA package - Latch characteristic 0mT BOP 15Gs typ Flux density SE package - Latch characteristic 4 V3.10 Nov 1, 2013 SS2406 Hall Latch - High Sensitivity netic fields with equivalent strength and opposite direction drive the output high and low. Powering-on the device in the hysteresis region (less than BOP and higher than BRP) allows an indeterminate output state. The correct state is attained after the first excursion beyond BOP or BRP. The SOT-23 device is reversed from the UA package. The SOT-23 output transistor will be latched on in the presence of a sufficiently strong North pole magnetic field applied to the marked face. Application Information It is strongly recommended that an external bypass capacitor be connected (in close proximity to the Hall sensor) between the supply (VDD Pin) and ground (GND Pin) of the device to reduce both external noise and noise generated by the chopper stabilization technique. As is shown in the following two figures in next page, a 0.1μF capacitor is typical. Typical Three-Wire Application Circuit VDD C1 SS2406 R2 OUT C2 GND For reverse voltage protection, it is recommended to connect a resistor or a diode in series with the VDD pin. When using a resistor, three points are important: - the resistor has to limit the reverse current to 50mA maximum (VCC / R1 ≤ 50mA) - the resulting device supply voltage VDD has to be higher than VDD min (VDD = VCC – R1*IDD) - the resistor has to withstand the power dissipated in reverse voltage condition (PD = VCC2/R1) When using a diode, a reverse current cannot flow and the voltage drop is almost constant (≈0.7V). Therefore, a 100Ω/0.25W resistor for 5V application and a diode for higher supply voltage are recommended. Both solutions provide the required reverse voltage protection. When a weak power supply is used or when the device is intended to be used in noisy environment, it is recommended the following figure is used. The low-pass filter formed by R1 and C1 and the Zener diode Z1 bypass the disturbances or voltage spikes occurring on the device supply voltage VDD. The diode D1 provides additional reverse voltage protection. Automotive and Severe Environment Protection Circuit R1:100 VDD C1 D1 Z1 SS2406 R2 OUT C2 GND 5 V3.10 Nov 1, 2013 SS2406 Hall Latch - High Sensitivity The SS2406 have been optimized for commutation applications in 5V and 12V brushless DC motors. The following figure in the next page is the typical application circuit for 3 phase brushless DC motors. ESD Precautions Electronic semiconductor products are sensitive to Electro Static Discharge (ESD). Always observe Electro Static Discharge control procedures whenever handling semiconductor products. 6 V3.10 Nov 1, 2013 SS2406 Hall Latch - High Sensitivity Package Information 2.13 1.87 0.75 ± 0.05 1.52 ± 0.1 Package UA, 3-Pin SIP: 3° ± 1° 1.00 1.20 45° ± 1° 4.0 ± 0.01 1 2 3 3.0 ± 0.01 Sensor Location Active Area Depth: 0.84(Nom) 3° ± 1° 6° ± 1° 3° ± 1° 6° ± 1° 1 2 0.05 ± 0.01 3 1.6.± 0.1 0.44± 0.01 0.38 ± 0.01 14 .5 ± 1 0.39± 0.01 Notes: 1). Controlling dimension : mm ; 2). Leads must be free of flash and plating voids ; 3). Do not bend leads within 1 mm of lead to package interface ; 4). PINOUT: Pin 1 VDD Pin 2 GND Pin 3 Output 1.27 2.54 7 V3.10 Nov 1, 2013 SS2406 Hall Latch - High Sensitivity Package SO, 3-Pin SOT-23: Notes 1). PINOUT: Top 3 2.60 1.50 3.00 1.80 1 Pin 1 VDD Pin 2 Output Pin 3 GND 2). All dimensions are in millimeters; 2 1.70 2.10 Side Vie End 2.70 3.10 0.10 0.25 1.00 1.30 0.70 0.90 0.20 Min 0.00 0.10 0.35 0.50 SOT-23 Package Hall Location: Bottom View of SOT-23 Package 3 Chip 0.56 0.66 0.95 2 1 1.50 Ordering Information Part No. Pb-free Temperature Code Package Code Packing SS2406ESOT YES -40°C to 85°C SOT-23 7-in. reel, 3000 pieces/reel SS2406EUA YES -40°C to 85°C TO-92 Bulk, 1000 pieces/bag SS2406KSOT YES -40°C to 125°C SOT-23 7-in. reel, 3000 pieces/reel SS2406KUA YES -40°C to 125°C TO-92 Bulk, 1000 pieces/bag SS2406LSOT YES -40°C to 150°C SOT-23 7-in. reel, 3000 pieces/reel SS2406LUA YES -40°C to 150°C TO-92 Bulk, 1000 pieces/bag 8 V3.10 Nov 1, 2013