VER:00 1 / 2 • 0.75 WATT UNREGULATED OUTPUT POWER • SINGLE-IN-LINE PACKAGE (SIP) • HIGH EFFICIENCY FOR LOW POWER APPLICATION • UL 94-V0 NON-CONDUCTED CASE • INTERNAL INPUT & OUTPUT FILTER • INPUT / OUTPUT ISOLATION UP TO 3KVDC The DUP75 series are the standard building blocks for on-board distributed power systems. They are ideally suited to providing single and dual supplies on primarily digital boards with added benefit of galvanic isolation to reduce switching noise. All of the rated power may be drawn from a single pin provided the total load does not exceed 0.75 watt. T E C H N I C A L S P E C I F I C AT I O N All specifications are typical at nominal input, full load and 25ºC otherwise noted OUTPUT SPECIFICATIONS GENERAL SPECIFICATIONS Output power Voltage accuracy 0.75 Watt max Full load and nominal Vin Minimum load (Note 1) ± 5% 10% of FL Line regulation LL to HL at Full Load Load regulation 10% to 100% FL Ripple and noise 20MHz bandwidth 1.2% / 1% of Vin 5V output others Temperature coefficient ± 10% ± 6% 50mVp-p ±0.1% / ºC, max Short circuit protection Short term INPUT SPECIFICATIONS Input voltage range Input filter Efficiency Isolation voltage See table Input to Output Standard Suffix-3KV 9 Isolation resistance 10 ohms, min Isolation capacitance 30pF, max Switching frequency Design meet safety standard Case material 100KHz, typ IEC60950, UL1950, EN60950 Non-conductive black plastic Potting material Epoxy (UL94-V0) 0.77 X 0.24 X 0.40 Inch (19.6 X 6.0 X 10.2 mm) Dimensions 5V nominal input 12V nominal input 15V nominal input 24V nominal input 4.5 – 5.5VDC 10.8 – 13.2VDC 13.5 – 16.5VDC 21.6 – 26.4VDC Capacitor 750VDC, min 3000VDC, min Weight 2.0g (0.071oz) MTBF (Note 2) 1.343 x 10 hrs 7 ENVIRONMENTAL SPECIFICATIONS Operating temperature range Cold start -40ºC ~ +85ºC (Non-derating) Above -25ºC Storage temperature range -55ºC ~ +105ºC Thermal shock MIL-STD-810D Vibration Relative humidity 10~55Hz, 2G, 30minutes along X,Y and Z 5% to 95% RH VER:00 Model Number Input Range Output Voltage Output Current Input Current (3) Eff (4) (%) Capacitor Load max(5) DUP75-05S05(-3KV) DUP75-05S12(-3KV) DUP75-05S15(-3KV) DUP75-05D05(-3KV) DUP75-05D12(-3KV) DUP75-05D15(-3KV) DUP75-12S05(-3KV) DUP75-12S12(-3KV) DUP75-12S15(-3KV) DUP75-12D05(-3KV) DUP75-12D12(-3KV) DUP75-12D15(-3KV) DUP75-15S05 DUP75-15S12 DUP75-15S15 DUP75-15D05 DUP75-15D12 DUP75-15D15 DUP75-24S05 DUP75-24S12 DUP75-24S15 DUP75-24D05 DUP75-24D12 DUP75-24D15 4.5 – 5.5 VDC 4.5 – 5.5 VDC 4.5 – 5.5 VDC 4.5 – 5.5 VDC 4.5 – 5.5 VDC 4.5 – 5.5 VDC 10.8 – 13.2 VDC 10.8 – 13.2 VDC 10.8 – 13.2 VDC 10.8 – 13.2 VDC 10.8 – 13.2 VDC 10.8 – 13.2 VDC 13.5 – 16.5 VDC 13.5 – 16.5 VDC 13.5 – 16.5 VDC 13.5 – 16.5 VDC 13.5 – 16.5 VDC 13.5 – 16.5 VDC 21.6 – 26.4 VDC 21.6 – 26.4 VDC 21.6 – 26.4 VDC 21.6 – 26.4 VDC 21.6 – 26.4 VDC 21.6 – 26.4 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC 150mA 62mA 50mA ± 75mA ± 30mA ± 25mA 150mA 62mA 50mA ± 75mA ± 30mA ± 25mA 150mA 62mA 50mA ± 75mA ± 30mA ± 25mA 150mA 62mA 50mA ± 75mA ± 30mA ± 25mA 231mA 213mA 211mA 227mA 212mA 214mA 96mA 89mA 88mA 93mA 85mA 88mA 78mA 71mA 70mA 75mA 68mA 70mA 49mA 45mA 45mA 47mA 43mA 45mA 69 74 75 70 72 74 69 74 75 71 75 75 68 74 75 71 75 75 68 70 71 70 69 72 4.7uF 4.7uF 4.7uF 2.2uF 2.2uF 2.2uF 4.7uF 4.7uF 4.7uF 2.2uF 2.2uF 2.2uF 4.7uF 4.7uF 4.7uF 2.2uF 2.2uF 2.2uF 4.7uF 4.7uF 4.7uF 2.2uF 2.2uF 2.2uF 0.77(19.6) Note 1. 2. 3. 4. 5. 2 / 2 The DUP75 series required a minimum 10% loading on the output to maintain specified regulation. Operation under no-load condition will not damage these devices, however they may not meet all listed specification BELLCORE TR-NWT-000332. Case I: 50% Stress, Temperature at 40ºC. (Ground fixed and controlled environment). Maximum value at nominal input voltage and full load of standard type. Typical value at nominal input voltage and full load. Test by minimum Vin and constant resistor load. 0.016(0.4) FRONT VIEW 0.40(10.2) 0.01x 0.02 ( 0.25 x 0.5) Rectangular Pin 0.10(2.54) 0.14(3.6) 0.085(2.16) 0.20(5.08) 0.24(6.1) 1 BOTTOM VIEW 2 4 5 6 7 0.053(1.35) 1. All dimensions in Inches (mm) 2. Pin pitch tolerance ±0.014(0.35) STANDARD “3KV” Models PIN SINGLE DUAL PIN SINGLE DUAL 1 2 4 5 6 7 + INPUT - INPUT - OUTPUT NC + OUTPUT No Pin + INPUT - INPUT 1 2 4 5 6 7 + INPUT - INPUT No Pin - OUTPUT NC + OUTPUT + INPUT - INPUT 2006_02_22. Änderungen vorbehalten / subject to change without notice. - OUTPUT COMMON + OUTPUT No Pin No Pin - OUTPUT COMMON + OUTPUT