OKI-78SR Series

OKI-78SR Series
www.murata-ps.com
Fixed Output 1.5 Amp SIP DC/DC Converters
Typical units
FEATURES
PRODUCT OVERVIEW

Ultra wide 7 to 36 VDC input range
Fabricated on a 0.41 by 0.65 inch (10.4 by 16.5
mm) Single Inline Package (SIP) module, the OKI78SR series are non-isolated switching regulator
(SR) DC/DC power converters for embedded applications. The fixed single output converters offer
both tight regulation and high efficiency directly
at the power usage site and are a direct plug-in
replacement for TO-220 package 78xx series linear
regulators. Typically, no extra outside components
are required.

Fixed Outputs of 3.3 or 5 VDC up to 1.5 Amps

Vertical or horizontal SIP-mount, small footprint
package

“No heat sink” direct replacement for 3-terminal
78xx-series linear regulators

High efficiency with no external components

Short circuit protection
Two nominal output voltages are offered (3.3
and 5 VDC), each with 1.5 Amp maximum output.
Based on fixed-frequency buck switching topology,
the high efficiency means very low heat and little
electrical noise, requiring no external components.
The ultra wide input range is 7 to 36 Volts DC.
Protection features include short circuit current
limit protection. The OKI-78SR is designed to meet
all standards approvals. RoHS-6 (no lead) hazardous material compliance is specified as standard.

Outstanding thermal derating performance

UL/EN/IEC 60950-1, 2nd Edition safety approvals
Connection Diagram
+Vin
+Vout
t4XJUDIJOH
F1
Controller
t'JMUFST
t$VSSFOU4FOTF
External
DC
Power
Source
Reference and
Error Amplifier
Common
Common
Figure 1. OKI-78SR
Note: Murata Power Solutions strongly recommends an external input fuse, F1.
See specifications.
For full details go to
www.murata-ps.com/rohs
www.murata-ps.com/support
MDC_OKI-78SR-W36.C03 Page 1 of 12
OKI-78SR Series
Fixed Output 1.5 Amp SIP DC/DC Converters
FUNCTIONAL SPECIFICATIONS SUMMARY AND ORDERING GUIDE
Output
VOUT
(Volts)
Root Model
IOUT
(Amps Power
max) (Watts)
R/N (mVp-p)
Max.
Input
Regulation (Typ.)
Line
VIN Nom. Range
(Volts) (Volts)
Load
Efficiency
IIN,
IIN,
no load full load
(mA)
(Amps)
Package
Min.
➀
Typ.
OKI-78SR-3.3/1.5-W36-C
3.3
1.5
4.95
40
±0.25%
±0.25%
24
7-36
5
0.48
84%
85.5%
OKI-78SR-5/1.5-W36-C
5
1.5
7.5
75
±0.25%
±0.25%
24
7-36
5
0.69
89%
90.5%
0.41 x 0.65 x 0.3
(10.4 x 16.5 x 7.62)
0.41 x 0.65 x 0.3
(10.4 x 16.5 x 7.62)
➀ Dimensions are in inches (mm).
➁ All specifications are at nominal line voltage, Vout = nominal and full load, +25 ˚C., with no external capacitor,
unless otherwise noted.
PART NUMBER STRUCTURE
OKI - 78SR 3.3 / 1.5 - W36 H - C
RoHS-6 Hazardous
Substance Compliance
Okami Non-Isolated PoL
Blank: Vertical Mount
H Suffix: Horizontal Mount
78SR Series
Note:
Some model number combinations
may not be available.
Contact Murata Power Solutions.
Maximum Rated Output in Volts
Maximum Rated Output
Current in Amps
Input Voltage Range
7-36V
Product Label
The manufacturing date code is four characters:
Because of the small size of these products, the product label contains a
character-reduced code to indicate the model number and manufacturing date
code. Not all items on the label are always used. Please note that the label differs from the product photograph on page 1. Here is the layout of the label:
The label contains three rows of information:
Mfg.
date
code
XXXXXX
Product code
YMDX Rev.
Revision level
Figure 2. Label Artwork Layout
First row – Murata Power Solutions logo
Second row – Model number product code (see table)
Third row – Manufacturing date code and revision level
Model Number
Product Code
OKI-78SR-3.3/1.5-W36-C
I33115
OKI-78SR-5/1.5-W36-C
I50115
OKI-78SR-3.3/1.5-W36H-C
I33115H
OKI-78SR-5/1.5-W36H-C
I50115H
First character – Last digit of manufacturing year, example 2009
Second character – Month code (1 through 9 = Jan-Sep;
O, N, D = Oct, Nov, Dec)
Third character – Day code (1 through 9 = 1 to 9, 10 = 0 and
11 through 31 = A through Z)
Fourth character – Manufacturing information
www.murata-ps.com/support
MDC_OKI-78SR-W36.C03 Page 2 of 12
OKI-78SR Series
Fixed Output 1.5 Amp SIP DC/DC Converters
Performance and Functional Specifications
All specifications are typical unless noted. See Note 1
Input
Input Voltage Range
See Ordering Guide.
Recommended External Fuse
2 Amps fast blow
Reverse Polarity Protection (Note 9) None. Install an external fuse.
Not isolated. The input and output share a
Isolation (note 5)
common return.
Start-Up Voltage
NA
Undervoltage Shutdown
NA
Overvoltage Shutdown
None
Internal Input Filter Type
Capacitive
Input Current:
Full Load Conditions
See Ordering Guide
Inrush Transient
0.16 A2Sec.
Shutdown Mode (Off, UV, OT)
1 mA
Output in Short Circuit
5 mA
No Load
5 mA
0.8 Amps (OKI-78SR-3.3/1.5-W36)
Low Line (Vin=Vmin, Vout=nom)
1.16 Amps (OKI-78SR-5/1.5-W36)
Reflected (Back) Ripple Current
10 mA pk-pk (OKI-78SR-3.3/1.5-W36)
(Note 2)
49 mA pk-pk (OKI-78SR-5/1.5-W36)
Output Voltage
Output Current Range
Minimum Loading (Note 11)
Maximum Output Power
Accuracy (50% load)
Overvoltage Protection (Note 7)
Temperature Coefficient
Ripple/Noise (20 MHz bandwidth)
Line/Load Regulation
Efficiency
Maximum Capacitive Loading
Cap-ESR=0.001 to 0.01 Ohms
Cap-ESR >0.01 Ohms
Current Limit Inception (98% of Vout
setting, after warm up)
Short Circuit Mode (Notes 6, 11)
Short Circuit Current Output
Protection Method
Short Circuit Duration
Prebias Startup
Output
See Ordering Guide
0 to 1.5 Amps
No minimum load
5.15 Watts (OKI-78SR-3.3/1.5-W36)
7.8 Watts (OKI-78SR-5/1.5-W36)
±4 % of Vnom
None
±0.02% per °C. of Vout range
See Ordering Guide and note 11
See Ordering Guide and note 10
See Ordering Guide and performance graphs
300 μF
3300 μF
3.5 Amps
10 mA
Hiccup autorecovery upon overload removal.
(Note 8)
Continuous, no damage (output shorted to
ground)
The converter will start up if the external output
voltage is less than Vnominal.
Dynamic Characteristics
Dynamic Load Response (50% to 100% load step, no external caps)
di/dt = 1 A/μSec
25 μSec settling time to within ±2% of final value
Peak deviation
100 mV
Switching Frequency
500 KHz
Environmental
Calculated MTBF (Note 4)
Ambient Temp.
Hours
+25°C
78,721,000
OKI-78SR-3.3/1.5-W36-C
Telecordia method (4a)
+40°C
59,017,000
+25°C
14,587,000
OKI-78SR-3.3/1.5-W36-C
MIL-HDBK-217N2 method (4b)
+40°C
9,814,000
Operating Ambient Temperature Range
Full power, with derating [3]
-40 to +85°C. see derating curves.
Storage Temperature Range
-55 to +125 °C.
Relative Humidity
to 85%/+85 °C.
Outline Dimensions
Weight
Safety
Physical
See Mechanical Specifications [11]
0.07 ounces (2 grams)
Certified to UL/cUL 60950-1
CSA-C22.2 No. 60950-1
IEC/EN 60950-1, 2nd Edition
Absolute Maximum Ratings
Input Voltage, Continuous or transient 36 Volts max.
Input Reverse Polarity Protection
None. Install external fuse.
Current-limited. Devices can withstand sustained
Output Current
short circuit without damage.
Storage Temperature
-40 to +125 deg. C.
Specification Notes:
(1)
All specifications are typical unless noted. General conditions for Specifications are +25 deg.C ambient
temperature, Vin=nominal, Vout=nominal, full rated load. Adequate airflow must be supplied for extended
testing under power. See Derating curves.
All models are tested and specified with no external capacitors. All models are stable and regulate within
spec under no-load conditions.
(2)
Input Back Ripple Current is tested and specified over a 5 Hz to 20 MHz bandwidth. Input filtering is Cin=2 x
100 μF, Cbus=1000 μF, Lbus=1 μH. All caps are low ESR types.
(3)
Note that Maximum Power Derating curves indicate an average current at nominal input voltage. At higher
temperatures and/or lower airflow, the DC/DC converter will tolerate brief full current outputs if the total
RMS current over time does not exceed the Derating curve. All Derating curves are presented near sea level
altitude. Be aware of reduced power dissipation with increasing altitude.
(4a) Mean Time Before Failure is calculated using the Telcordia (Belcore) SR-332 Method 1, Case 3, ground fixed
conditions, Tpcboard=+25 ˚C, full output load, natural air convection.
(4b) Mean Time Before Failure is calculated using the MIL-HDBK-217N2 method, ground benign, +25ºC., full
output load, natural convection.
(5)
The input and output are not isolated. They share a single COMMON power and signal return.
(6)
Short circuit shutdown begins when the output voltage degrades approximately 2% from the selected
setting. Output current limit and short circuit protection are non-latching. When the overcurrent fault is
removed, the converter will immediately recover.
(7)
The output is not intended to sink appreciable reverse current.
(8)
“Hiccup” overcurrent operation repeatedly attempts to restart the converter with a brief, full-current output.
If the overcurrent condition still exists, the restart current will be removed and then tried again. This short
current pulse prevents overheating and damaging the converter.
(9)
Input Fusing: If reverse polarity is accidentally applied to the input, to ensure reverse input protection,
always connect an external input fast-blow fuse in series with the +Vin input. Use approximately twice the
full input current rating with nominal input voltage.
(10) Regulation specifications describe the deviation as the line input voltage or output load current is varied
from a nominal midpoint value to either extreme.
(11) Output noise may be further reduced by installing an external filter. Do not exceed the maximum output
capacitance. At zero output current and no external capacitor, the output may contain low frequency
components which exceed the ripple specification. The output may be operated indefinitely with no load.
www.murata-ps.com/support
MDC_OKI-78SR-W36.C03 Page 3 of 12
OKI-78SR Series
Fixed Output 1.5 Amp SIP DC/DC Converters
PERFORMANCE DATA – OKI-78SR-3.3/1.5-W36
Efficiency vs. Line Voltage and Load Current @ +25˚C. (Vout = Vnom.)
Maximum Current Temperature Derating at sea level (Vin=7V. to 36V.)
2.00
100
90
80
VIN = 7V
VIN = 12V
VIN = 36V
60
Output Current (Amps)
Efficiency (%)
70
50
40
30
0.33 m/s (65 LFM)
1.00
20
10
0
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
Load Curre nt (Amps)
Output Ripple and Noise (Vin=7V, Vout=nominal, Iout=1.6A, Cload=0, Ta=+25˚C.,
ScopeBW=100MHz)
0.00
20
25
30
35
40
45
50
55
60
65
70
75
80
85
Ambient Temperature (ºC)
Output Ripple and Noise (Vin=12V, Vout=nominal, Iout=1.6A, Cload=0, Ta=+25˚C.,
ScopeBW=100MHz)
Output Ripple and Noise (Vin=36V, Vout=nominal, Iout=1.6A, Cload=0, Ta=+25˚C.,
ScopeBW=100MHz)
www.murata-ps.com/support
MDC_OKI-78SR-W36.C03 Page 4 of 12
OKI-78SR Series
Fixed Output 1.5 Amp SIP DC/DC Converters
PERFORMANCE DATA – OKI-78SR-3.3/1.5-W36
Step Load Transient Response (Vin=7V, Vout=nominal, Cload=0, Iout=0.75A to 1.5A,
Slew=1A/μS, Ta=+25˚C.) Trace 2=Vout, 100 mV/div. Trace 4=Iout, 0.5A/div
Step Load Transient Response (Vin=7V, Vout=nominal, Cload=0, Iout=1.5A to 0.75A,
Slew=1A/μS, Ta=+25˚C.) Trace 2=Vout, 100 mV/div. Trace 4=Iout, 0.5A/div.
Step Load Transient Response (Vin=12V, Vout=nominal, Cload=0, Iout=0.75A to 1.5A,
Slew=1A/μS, Ta=+25˚C.) Trace 2=Vout, 100 mV/div. Trace 4=Iout, 0.5A/div.
Step Load Transient Response (Vin=12V, Vout=nominal, Cload=0, Iout=1.5A to 0.75A,
Slew=1A/μS, Ta=+25˚C.) Trace 2=Vout, 100 mV/div. Trace 4=Iout, 0.5A/div.
Step Load Transient Response (Vin=36V, Vout=nominal, Cload=0, Iout=0.75A to 1.5A,
Slew=1A/μS, Ta=+25˚C.) Trace 2=Vout, 100 mV/div. Trace 4=Iout, 0.5A/div.
Step Load Transient Response (Vin=36V, Vout=nominal, Cload=0, Iout=1.5A to 0.75A,
Slew=1A/μS, Ta=+25˚C.) Trace 2=Vout, 100 mV/div. Trace 4=Iout, 0.5A/div.
www.murata-ps.com/support
MDC_OKI-78SR-W36.C03 Page 5 of 12
OKI-78SR Series
Fixed Output 1.5 Amp SIP DC/DC Converters
PERFORMANCE DATA – OKI-78SR-5/1.5-W36
Efficiency vs. Line Voltage and Load Current @ +25˚C. (Vout = Vnom.)
Maximum Current Temperature Derating at sea level (Vin=7V. to 36V.)
2.00
100
90
80
Efficiency (%)
60
Output Current (Amps)
VIN = 7V
VIN = 12V
VIN = 36V
70
50
40
30
0.33 m/s (65 LFM)
1.00
20
10
0
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
Load Curre nt (Amps)
Output Ripple and Noise (Vin=7V, Vout=nominal, Iout=1.6A, Cload=0, Ta=+25˚C.,
ScopeBW=100MHz)
0.00
20
25
30
35
40
45
50
55
60
65
70
75
80
85
Ambient Temperature (ºC)
Output Ripple and Noise (Vin=12V, Vout=nominal, Iout=1.6A, Cload=0, Ta=+25˚C.,
ScopeBW=100MHz)
Output Ripple and Noise (Vin=36V, Vout=nominal, Iout=1.6A, Cload=0, Ta=+25˚C.,
ScopeBW=100MHz)
www.murata-ps.com/support
MDC_OKI-78SR-W36.C03 Page 6 of 12
OKI-78SR Series
Fixed Output 1.5 Amp SIP DC/DC Converters
PERFORMANCE DATA – OKI-78SR-5/1.5-W36
Step Load Transient Response (Vin=7V, Vout=nominal, Cload=0, Iout=0.75A to 1.5A,
Slew=1A/μS, Ta=+25˚C.) Trace 2=Vout, 100 mV/div. Trace 4=Iout, 0.5A/div.
Step Load Transient Response (Vin=7V, Vout=nominal, Cload=0, Iout=1.5A to 0.75A,
Slew=1A/μS, Ta=+25˚C.) Trace 2=Vout, 100 mV/div. Trace 4=Iout, 0.5A/div.
Step Load Transient Response (Vin=12V, Vout=nominal, Cload=0, Iout=0.75A to 1.5A,
Slew=1A/μS, Ta=+25˚C.) Trace 2=Vout, 100 mV/div. Trace 4=Iout, 0.5A/div.
Step Load Transient Response (Vin=12V, Vout=nominal, Cload=0, Iout=1.5A to 0.75A,
Slew=1A/μS, Ta=+25˚C.) Trace 2=Vout, 100 mV/div. Trace 4=Iout, 0.5A/div.
Step Load Transient Response (Vin=36V, Vout=nominal, Cload=0, Iout=0.75A to 1.5A,
Slew=1A/μS, Ta=+25˚C.) Trace 2=Vout, 100 mV/div. Trace 4=Iout, 0.5A/div.
Step Load Transient Response (Vin=36V, Vout=nominal, Cload=0, Iout=1.5A to 0.75A,
Slew=1A/μS, Ta=+25˚C.) Trace 2=Vout, 100 mV/div. Trace 4=Iout, 0.5A/div.
www.murata-ps.com/support
MDC_OKI-78SR-W36.C03 Page 7 of 12
OKI-78SR Series
Fixed Output 1.5 Amp SIP DC/DC Converters
MECHANICAL SPECIFICATIONS, VERTICAL MOUNT
0.30 (7.6)
0.41
(10.4)
0.205
(5.2)
REF
0.16 (4.1)
CL
0.06
(1.5)
REF
0.65
(16.5)
Pin #3
0.13 (3.3)
Pin #1
0.030±0.002
0.100 (2.5)
0.05 (1.3)
0.200 (5.1)
Pin #1
PIN MATERIAL: COPPER ALLOY
PIN FINISH: PURE MATTE TIN 100-300 u"
OVER 75-150 u" NICKEL
Pin #1
INPUT/OUTPUT CONNECTIONS
OKI-78SR
Pin
1
2
3
Function
Positive Input
Common (Ground)
Positive Output
Dimensions are in inches (mm shown for ref. only).
Third Angle Projection
Tolerances (unless otherwise specified):
.XX ± 0.02 (0.5)
.XXX ± 0.010 (0.25)
Angles ± 1˚
Components are shown for reference only.
www.murata-ps.com/support
MDC_OKI-78SR-W36.C03 Page 8 of 12
OKI-78SR Series
Fixed Output 1.5 Amp SIP DC/DC Converters
MECHANICAL SPECIFICATIONS, HORIZONTAL MOUNT
0.30 (7.6)
0.41
(10.4)
0.205
(5.2)
REF
0.65
(16.5)
Pin #1
0.100 (2.5)
0.16 (4.1)
CL
0.06
(1.5)
REF
.025 (0.635)
(3 PLS)
Pin #3
0.17 +.01
(4.318) - .02
.05 (1.3)±.01
0.200 (5.1)
Pin #1
PIN MATERIAL: COPPER ALLOY
PIN FINISH: PURE MATTE TIN 100-300 u"
OVER 75-150 u" NICKEL
Pin #1
INPUT/OUTPUT CONNECTIONS
OKI-78SR
Pin
1
2
3
Function
Positive Input
Common (Ground)
Positive Output
Dimensions are in inches (mm shown for ref. only).
Third Angle Projection
Tolerances (unless otherwise specified):
.XX ± 0.02 (0.5)
.XXX ± 0.010 (0.25)
Angles ± 1˚
Components are shown for reference only.
www.murata-ps.com/support
MDC_OKI-78SR-W36.C03 Page 9 of 12
OKI-78SR Series
Fixed Output 1.5 Amp SIP DC/DC Converters
STANDARD PACKAGING
Each static dissipative polyethylene foam tray
accommodates 120 converters
2.5±.25 (63.5)
Closed height
10.00 ±.25
(254.0)
10.00±.25
(254.0)
Carton accommodates three (3) trays of 120 yielding 360 converters per carton.
9.92
(252.0)
0.49
(12.5)
6.5 X 45°
x4
0.63 (16.0)
0.39 (10.0)
0.94
(24.0)
9.92
(252.0)
0.2
(5.0)
0.33
(8.5)
0.43
(11.0)
0.2
(5.0)
Dimensions are in inches (mm shown for ref. only).
Third Angle Projection
Notes:
1. Material: Dow 220 antistat ethafoam
(Density: 34-35 kg/m3)
2. Dimensions: 252 x 252 x 16 mm
8 x 15 array (120 per tray)
Tolerances (unless otherwise specified):
.XX ± 0.02 (0.5)
.XXX ± 0.010 (0.25)
Angles ± 2˚
Components are shown for reference only.
www.murata-ps.com/support
MDC_OKI-78SR-W36.C03 Page 10 of 12
OKI-78SR Series
Fixed Output 1.5 Amp SIP DC/DC Converters
TECHNICAL NOTES
Input Fusing
Certain applications and/or safety agencies may require fuses at the inputs of
power conversion components. Fuses should also be used when there is the
possibility of sustained input voltage reversal which is not current-limited. For
greatest safety, we recommend a fast blow fuse installed in the ungrounded
input supply line.
TO
OSCILLOSCOPE
+VIN
VIN
The installer must observe all relevant safety standards and regulations. For
safety agency approvals, install the converter in compliance with the end-user
safety standard.
Recommended Input Filtering
The user must assure that the input source has low AC impedance to provide
dynamic stability and that the input supply has little or no inductive content,
including long distributed wiring to a remote power supply. The converter will
operate with no additional external capacitance if these conditions are met.
For best performance, we recommend installing a low-ESR capacitor
immediately adjacent to the converter’s input terminals. The capacitor should
be a ceramic type such as the Murata GRM32 series or a polymer type. Initial
suggested capacitor values are 10 to 22 μF, rated at twice the expected maximum input voltage. Make sure that the input terminals do not go below the
undervoltage shutdown voltage at all times. More input bulk capacitance may
be added in parallel (either electrolytic or tantalum) if needed.
Recommended Output Filtering
The converter will achieve its rated output ripple and noise with no additional
external capacitor. However, the user may install more external output capacitance to reduce the ripple even further or for improved dynamic response.
Again, use low-ESR ceramic (Murata GRM32 series) or polymer capacitors.
Initial values of 10 to 47 μF may be tried, either single or multiple capacitors in
parallel. Mount these close to the converter. Measure the output ripple under
your load conditions.
CURRENT
PROBE
+
–
+
–
LBUS
CBUS
CIN
-VIN
CIN = 2 x 100μF, ESR < 700mΩ @ 100kHz
CBUS = 1000μF, ESR < 100mΩ @ 100kHz
LBUS = 1μH
Figure 3 Measuring Input Ripple Current
+VOUT
C1
C2
SCOPE
RLOAD
-VOUT
C1 = 1μF
C2 = 10μF
LOAD 2-3 INCHES (51-76mm) FROM MODULE
Figure 4. Measuring Output Ripple and Noise (PARD)
Use only as much capacitance as required to achieve your ripple and noise
objectives. Excessive capacitance can make step load recovery sluggish or
possibly introduce instability. Do not exceed the maximum rated output capacitance listed in the specifications.
Input Ripple Current and Output Noise
All models in this converter series are tested and specified for input reflected
ripple current and output noise using designated external input/output components, circuits and layout as shown in the following figures. The Cbus and Lbus
components simulate a typical DC voltage bus. Please note that the values of
Cin, Lbus and Cbus will vary according to the specific converter model.
www.murata-ps.com/support
MDC_OKI-78SR-W36.C03 Page 11 of 12
OKI-78SR Series
Fixed Output 1.5 Amp SIP DC/DC Converters
Minimum Output Loading Requirements
All models regulate within specification and are stable under no load to full
load conditions. Operation under no load might however slightly increase
output ripple and noise.
Temperature Derating Curves
The graphs in this data sheet illustrate typical operation under a variety of
conditions. The Derating curves show the maximum continuous ambient air
temperature and decreasing maximum output current which is acceptable
under increasing forced airflow measured in Linear Feet per Minute (“LFM”).
Note that these are AVERAGE measurements. The converter will accept brief
increases in current or reduced airflow as long as the average is not exceeded.
Note that the temperatures are of the ambient airflow, not the converter
itself which is obviously running at higher temperature than the outside air.
Also note that “natural convection” is defined as very flow rates which are not
using fan-forced airflow. Depending on the application, “natural convection” is
usually about 30-65 LFM but is not equal to still air (0 LFM).
Output Fusing
The converter is extensively protected against current, voltage and temperature
extremes. However your output application circuit may need additional protection. In the extremely unlikely event of output circuit failure, excessive voltage
could be applied to your circuit. Consider using an appropriate fuse in series
with the output.
Output Current Limiting
Current limiting inception is defined as the point at which full power falls below
the rated tolerance. See the Performance/Functional Specifications. Note particularly that the output current may briefly rise above its rated value in normal
operation as long as the average output power is not exceeded. This enhances
reliability and continued operation of your application. If the output current is
too high, the converter will enter the short circuit condition.
Murata Power Solutions makes Characterization measurements in a closed
cycle wind tunnel with calibrated airflow. We use both thermocouples and an
infrared camera system to observe thermal performance. As a practical matter,
it is quite difficult to insert an anemometer to precisely measure airflow in
most applications. Sometimes it is possible to estimate the effective airflow if
you thoroughly understand the enclosure geometry, entry/exit orifice areas and
the fan flowrate specifications.
Output Short Circuit Condition
When a converter is in current-limit mode, the output voltage will drop as the
output current demand increases. If the output voltage drops too low (approximately 98% of nominal output voltage for most models), the bias voltage may
shut down the PWM controller. Following a time-out period, the PWM will
restart, causing the output voltage to begin rising to its appropriate value. If the
short-circuit condition persists, another shutdown cycle will initiate. This rapid
on/off cycling is called “hiccup mode”. The hiccup cycling reduces the average
output current, thereby preventing excessive internal temperatures and/or
component damage.
CAUTION: If you routinely or accidentally exceed these Derating guidelines,
the converter may have an unplanned Over Temperature shut down. Also, these
graphs are all collected at near Sea Level altitude. Be sure to reduce the derating for higher altitude.
The “hiccup” system differs from older latching short circuit systems
because you do not have to power down the converter to make it restart. The
system will automatically restore operation as soon as the short circuit condition is removed.
Soldering Guidelines
Murata Power Solutions recommends the specifications below when installing these converters. These specifications vary depending on the solder type. Exceeding these specifications may cause damage to the product. Your production environment may differ; therefore please thoroughly review these guidelines with your process engineers.
Wave Solder Operations for through-hole mounted products (THMT)
For Sn/Ag/Cu based solders:
Maximum Preheat Temperature
For Sn/Pb based solders:
115° C.
Maximum Preheat Temperature
105° C.
Maximum Pot Temperature
270° C.
Maximum Pot Temperature
250° C.
Maximum Solder Dwell Time
7 seconds
Maximum Solder Dwell Time
6 seconds
Murata Power Solutions, Inc.
11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A.
ISO 9001 and 14001 REGISTERED
This product is subject to the following operating requirements
and the Life and Safety Critical Application Sales Policy:
Refer to: http://www.murata-ps.com/requirements/
Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other
technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply
the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without
notice.
© 2014 Murata Power Solutions, Inc.
www.murata-ps.com/support
MDC_OKI-78SR-W36.C03 Page 12 of 12