DM632B - Silicon Touch Technology Inc.

DM632B
Version
: PRE.001
Issue Date : 2008/07/31
File Name : SP-DM632B-PRE.001.doc
Total Pages : 31
16-CHANNEL CONSTANT CURRENT LED DRIVER
WITH 16-bit PROGRAMMABLE PWM OUTPUTS
新竹市科學園區展業一路 9 號 7 樓之 1
SILICON TOUCH TECHNOLOGY INC.
9-7F-1, Prosperity Road I, Science Based Industrial Park,
Hsin-Chu, Taiwan 300, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
DM632B
16-CHANNEL CONSTANT CURRENT LED DRIVER
WITH 16-bit PROGRAMMABLE PWM OUTPUTS
General Description
DM632B is a 16-channel constant current sink LED driver. Each channel has independent
16-bits (65536 steps) grayscale PWM control current outputs. It incorporates shift registers, data
latches, constant current circuitry with current value set by an external resistor, and built-in LED
open detection circuit to detect error status. It combines the selections with rising / falling edge
serial out, auto-reload/one-shot PWM output, internal/external grayscale clock source. It is
specifically designed for LED display or lighting applications.
Features
z
Constant-current outputs: 5mA to 60mA adjustable by one external resistor
z
16-bit linear PWM control current outputs for each channel
z
Maximum output voltage: 17V
z
Maximum clock frequency: 25MHz
z
Auto-Reload / One-Shot Mode selection.
z
Serial out clock edge selection – Rising / Falling edge selection
z
Internal / External PWM clock mode selection
z
Built-in real-time open detection
z
Package and pin assignment compatible to conventional LED drivers
(DM134/5/6, DM13C)
z
Power supply voltage: 3.3V to 5V
z
Schmitt Trigger input
z
Output channel delay
Applications
z
Indoor/Outdoor LED Video Display
z
LED Variable Message Signs (VMS) System
z
LED Decorative Lighting
Package Types
z
DIP24B, SOP24B, SSOP24, TSSOP24E (with exposed pad)
16-channel 16-bit PWM Constant Current LED Driver
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 1
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Block Diagram
OUT 0
OUT 1
OUT 15
LED Open Detector
(0)
LED Open Detector
(1)
LED Open Detector
(15)
Internal
Oscillator
Constant Current Driver
(0)
Constant Current Driver
(1)
Constant Current Driver
(15)
REXT
16-bit
Counter
16-bit PWM Generator
(0)
16-bit PWM Generator
(1)
16-bit PWM Generator
(15)
GCK
VCC
GND
16
LAT
16-bit Latch Register
(0)
16
16-bit Latch Register
(1)
16
DAI
16-bit Shift Register
(0)
16
16-bit Latch Register
(15)
16
16
16-bit Shift Register
(1)
16-bit Shift Register
(15)
DAO
DCK
16-channel 16-bit PWM Constant Current LED Driver
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 2
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Pin Connection
GND
DAI
DCK
LAT
OUT0
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
1
24
2
DIP24B
3
4
SOP24
5
22
21
20
6
SOP24B
7
8
23
19
18
TSSOP24E
9
16
10
11
17
15
( top view )
12
14
13
VCC
REXT
DAO
GCK
OUT 15
OUT 14
OUT 13
OUT 12
OUT 11
OUT 10
OUT 9
OUT 8
Pin Description
PIN No.
PIN
NAME
FUNCTION
SOP24B/SSOP24/TSSOP24E: 1
TSSOP24E: exposed pad
GND
Ground terminal.
SOP24B/SSOP24/TSSOP24E: 2
DAI
Serial data input terminal.
SOP24B/SSOP24/TSSOP24E: 3
DCK
Synchronous clock input terminal for serial data transfer.
Data is sampled at the rising edge of DCK.
LAT
Input terminal of data strobe:
‘H’ means data on shift register goes through latch
(level trigger), all outputs off and counter reset
immediately
‘L’ means data is latched.
SOP24B/SSOP24/TSSOP24E: 4
SOP24B/SSOP24/TSSOP24E: 5~20
OUT0~15 Sink constant-current outputs (open-drain).
Gray Scale Clock (GCK) :
Input terminal for PWM operation.
SOP24B/SSOP24/TSSOP24E: 21
GCK
SOP24B/SSOP24/TSSOP24E: 22
DAO
Serial data output terminal.
Data shift out at the rising edge of DCK in REM∗1 (default),
or data shift out at the falling edge of DCK in FEM∗2.
SOP24B/SSOP24/TSSOP24E: 23
REXT
External resistors connected between REXT and GND for
output current value setting.
SOP24B/SSOP24/TSSOP24E: 24
VCC
Supply voltage terminal.
∗
1 Rising Edge Mode
2 Falling Edge Mode
∗
16-channel 16-bit PWM Constant Current LED Driver
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 3
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Equivalent Circuit of Inputs and Outputs
1. DCK, DAI, LAT , GCK terminals
2. DAO terminals
PCB Layout Consideration
To connect an external resistor to REXT pin and ground can determine the maximum output
current. If there is any disturbance occurred to REXT pin, the constant current output may be
unstable or has noise happened. Since REXT (pin23), DAO (pin22), and GCK (pin21) are next to
each other, the most possible interference is caused by DAO or GCK signal. Accordingly, it is
recommended that adding some shielding area within the above pins in PCB layout, or laying the
signal line of above pins on different PCB layer will prevent the noise problems effectively.
16-channel 16-bit PWM Constant Current LED Driver
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 4
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Maximum Ratings (Ta=25°C, Tj(max) = 150°C)
CHARACTERISTIC
SYMBOL
RATING
UNIT
Supply Voltage
VCC
-0.3 ~ 7.0
V
Input Voltage
VIN
-0.3 ~ VCC+0.3
V
Output Current
IOUT
70
mA
Output Voltage
VOUT
-0.3 ~ 17
V
Input Clock Frequency
FDCK
25
MHz
GND Terminal Current
IGND
1120
mA
4.17 ( TSSOP24E exposed pad)
Power Dissipation
(4 layer PCB, at Ta=25℃)
2.19 ( SOP24B)
PD
W
1.87 (DIP24B)
1.79 ( SSOP24 )
30 ( TSSOP24E exposed pad)
Thermal Resistance
(4 layer PCB, at Ta=25℃)
57 (SOP24B)
Rth(j-a)
°C/W
67 (DIP24B)
70 (SSOP24 )
Operating Temperature
Top
-40 ~ 85
°C
Storage Temperature
Tstg
-55 ~ 150
°C
Recommended Operating Condition
CHARACTERISTIC
Supply Voltage
Output Voltage
Output Voltage
Output Current
Input Voltage
SYMBOL
CONDITION
MIN.
TYP.
MAX.
UNIT
VCC
⎯
3.3
5.0
5.5
V
1.0
⎯
0.5VCC
⎯
⎯
17
VOUT
VOUT
*1
Driver On
*2
Driver Off
IO
OUTn
5
⎯
60
IOH
VOH = VCC – 0.4 V
⎯
⎯
+1.5
IOL
VOL = 0.2 V
⎯
⎯
-1.5
VIH
VIL
VCC = 3.3 V ~ 5.5V
0.8VCC
⎯
VCC
0.0
⎯
0.2VCC
Input Clock Frequency
FDCK
Single Chip Operation
⎯
⎯
25
Input PWM Frequency
FGCK
3.3V~5.5V
⎯
⎯
25
LAT Pulse Width
tw LAT
15
⎯
⎯
DCK Pulse Width
tw DCK
15
⎯
⎯
10
⎯
⎯
10
⎯
⎯
10
⎯
⎯
⎯
⎯
Set-up Time for DAI
tsetup(D)
Hold Time for DAI
thold(D)
Set-up Time for LAT
tsetup(L)
Hold Time for LAT
VCC = 5.0V
thold(L)
*3
360
V
mA
V
MHz
ns
*1
Notice that the power dissipation is limited to its package and ambient temperature.
The driver output voltage including any overshoot stress has to be compliant with the maximum voltage (17V).
*3
Due to open detection operation and output channel delay consideration.
*2
16-channel 16-bit PWM Constant Current LED Driver
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 5
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Electrical Characteristics (VCC = 5.0 V, Ta = 25°C unless otherwise noted)
CHARACTERISTIC
Output Leakage Current
SYMBOL
CONDITION
MIN.
TYP.
MAX.
UNIT
IOL
VOH = 17 V
⎯
⎯
±1.0
uA
VOL
IOL = 1.25 mA
⎯
⎯
0.4
VOH
IOH= 1.4 mA
VCC-0.2
⎯
⎯
⎯
⎯
±3
%
TBD
TBD
TBD
mA
Rrext = 2.2 KΩ
VOUT = 1 V ~ 3 V
⎯
±0.1
±0.5
% / VCC
Rrext = 2.2 KΩ
⎯
±1
±4
V(od)
all outputs turn on
⎯
0.2
⎯
IDD(off)
power on
all pins are open
unless VCC and GND
(internal GCK mode
⎯
5.5
⎯
IDD(off)
power on
all pins are open
unless VCC and GND
(external GCK mode)
⎯
5.0
⎯
IDD(on)
input signal is static
Rrext = 12.4 KΩ
all outputs turn off
⎯
6.0
⎯
IDD(on)
input signal is static
Rrext = 2.2 KΩ
all outputs turn off
⎯
8.5
⎯
IDD(on)
input signal is static
Rrext = 570 Ω
all outputs turn off
⎯
17.5
⎯
Output Voltage (S-OUT)
Output Current Skew
(Channel-to-Channel)
IOL1
*1
VOUT = 1.0 V
Rrext = 2.2 KΩ
Output Current Skew
(Chip-to-Chip)
IOL2
*2
Output Voltage Regulation
% / VOUT
Supply Voltage Regulation
LED Open Detection Threshold
Supply Current
V
*3
%/V
V
mA
*1
Channel-to-channel skew is defined as the ratio between (any Iout – average Iout) and average Iout, where average
Iout = (Imax + Imin) / 2.
*2
Chip-to-Chip skew is defined as the range into which any output current of any IC falls.
*3
IO excluded.
16-channel 16-bit PWM Constant Current LED Driver
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 6
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Electrical Characteristics (VCC = 3.3 V, Ta = 25°C unless otherwise noted)
CHARACTERISTIC
Output Leakage Current
SYMBOL
CONDITION
MIN.
TYP.
MAX.
UNIT
IOL
VOH = 17 V
-1.0
⎯
+1.0
uA
VOL
IOL = 1.25 mA
⎯
⎯
0.4
VOH
IOH= 1.4 mA
VCC-0.2
⎯
⎯
⎯
⎯
±3
%
TBD
TBD
TBD
mA
Rrext = 2.2 KΩ
VOUT = 1 V ~ 3 V
⎯
±0.1
±0.5
% / VCC
Rrext = 2.2 KΩ
⎯
±1
±4
V(od)
all outputs turn on
⎯
0.2
⎯
IDD(off)
power on
all pins are open
unless VCC and GND
(internal GCK mode)
⎯
4.5
⎯
IDD(off)
power on
all pins are open
unless VCC and GND
(external GCK mode)
⎯
4.2
⎯
IDD(on)
input signal is static
Rrext = 12.4 KΩ
all outputs turn off
⎯
5.5
⎯
IDD(on)
input signal is static
Rrext = 2.2 KΩ
all outputs turn off
⎯
7.0
⎯
IDD(on)
input signal is static
Rrext = 570 Ω
all outputs turn off
⎯
15.0
⎯
Output Voltage (S-OUT)
Output Current Skew
(Channel-to-Channel)
IOL1
*1
VOUT = 1.0 V
Rrext = 2.2 KΩ
Output Current Skew
(Chip-to-Chip)
IOL2
*2
Output Voltage Regulation
% / VOUT
Supply Voltage Regulation
LED Open Detection Threshold
Supply Current
V
*3
%/V
V
mA
*1
Channel-to-channel skew is defined as the ratio between (any Iout – average Iout) and average Iout, where average
Iout = (Imax + Imin) / 2.
*2
Chip-to-Chip skew is defined as the range into which any output current of any IC falls.
*3
IO excluded.
16-channel 16-bit PWM Constant Current LED Driver
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 7
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Switching Characteristics (VCC = 5.0V, Ta = 25°C unless otherwise noted)
CHARACTERISTIC
SYMBOL
DCK(rising edge)-to-DAO
tpLH
DCK(falling edge)-to-DAO
Propagation Delay
(‘H’ to ‘L’)
MIN.
TYP.
MAX.
⎯
45.7
⎯
VIH = VCC
⎯
36
⎯
VIL = GND
⎯
16
⎯
⎯
23.8
⎯
⎯
28
⎯
⎯
14
⎯
⎯
18
⎯
GCK-to-OUT
Propagation Delay
(‘L’ to ‘H’)
CONDITION
GCK-to-OUT
DCK(rising edge)-to-DAO
Rrext = 2.2 KΩ
tpHL
VL = 5.0 V
DCK(falling edge)-to-DAO
CL = 13 pF
Output Current Rise Time
tor
Output Current Fall Time
tof
⎯
7.0
⎯
Output Delay Time Unit
Td
⎯
20
⎯
UNIT
ns
Switching Characteristics (VCC = 3.3V, Ta = 25°C unless otherwise noted)
CHARACTERISTIC
0Propagation Delay
(‘L’ to ‘H’)
CONDITION
MIN.
TYP.
MAX.
⎯
48.8
⎯
VIH = VCC
⎯
23
⎯
VIL = GND
⎯
23
⎯
⎯
29.6
⎯
⎯
21
⎯
⎯
20
⎯
⎯
20
⎯
GCK-to-OUT
DCK(rising edge)-to-DAO
tpLH
DCK(falling edge)-to-DAO
Propagation Delay
(‘H’ to ‘L’)
SYMBOL
GCK-to-OUT
Rrext = 2.2 KΩ
DCK(rising edge)-to-DAO
tpHL
VL = 3.3 V
DCK(falling edge)-to-DAO
CL = 13 pF
Output Current Rise Time
tor
Output Current Fall Time
tof
⎯
8.3
⎯
Output Delay Time Unit
Td
⎯
30
⎯
UNIT
ns
VL
VCC
A
DAI
DCK
LAT
GCK
CL
CL
CL
OUTn
REXT
DAO
Rrext
CL
CL
GND
Switching Characteristics Test Circuit
16-channel 16-bit PWM Constant Current LED Driver
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 8
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Constant-Current Output
Constant-current value (Iout*1) of each output channel is set by an external resistor connected
between the REXT pin and GND. The current scale ranging can be adjusted from 5mA to 60mA by
varying the resistor value. The reference voltage of REXT terminal (Vrext) is approximately 1.23V.
The output current value is calculated by the following equation:
Iout(mA)
5
10
20
30
40
50
60
M
37.11
36.29
37.55
39.03
40.36
40.4
41.28
Output current as a function of Rext value
70
60
Iout (mA) ~
Iout(mA)
50
Vrext (V)
× M
Rrext (KΩ)
40
30
20
10
0
0
1000
2000
3000
4000
5000
6000
7000
8000
1.4
1.6
9000
10000
Rext
Output Current as a function of Output Voltage
70
60
Iout(A)
50
40
30
20
10
0
0
0.2
0.4
0.6
0.8
1
1.2
1.8
2
Vout(V)
In order to obtain a good performance of constant-current output, a suitable output voltage is
necessary. Users can get related information about the minimum output voltage above.
*1
Iout is typical current value setting under 100% PWM duty cycle .
16-channel 16-bit PWM Constant Current LED Driver
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 9
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Serial Data Interface
The serial-in data (DAI) data will be clocked into 16 × 16 bit shift registers synchronized on
the rising edge of the clock (DCK). The data will be transferred into the 16 × 16 bit latch registers
when the strobe signal ( LAT ) is kept at high level (level trigger); Otherwise, the data will be held.
The latch pulse should be sent after the falling edge of the last clock within one frame data. The
serial-out data (DAO) will be shifted out on synchronization of the clock (DCK).
Input Data clock-in sequence
The sequence of the grayscale PWM luminous data of a driver showed as following diagram.
The input data sequence of input data is from the MSB of OUT15 (D15 [15:0]) to the LSB of OUT0
(D0 [15:0]) by time passing.
Serial-out Data clock-out sequence
The data serial out from DAO include latched grayscale data and the LSB of each output data
covered by detection message (ERR) after LAT pulse be active. The serial out sequence of the
data is from the MSB of OUT15 (D15 [15:0]) to the LSB of OUT0 (D0 [15:0]) by time passing.
shift out first
OUT 15
D15 [15]
D15 [14]
D15[13]
D15 [12]
D15[11]
D15 [10]
D15 [9]
MSB
D14 [15]
D15[8]
D15[7]
D15 [6]
D15[5]
D15[4]
D 15[3]
D15 [2]
D15[1]
LSB
OUT 14
D14[14]
D14 [13]
D14 [12]
D14[11]
D14 [10]
D14[9]
D14[8]
D14 [7]
ERR [15]
D14[6]
D14[5]
D 14[4]
D14 [3]
D14[2]
D 14[1]
ERR[14]
LSB
MSB
OUT 0
D0 [15]
D0 [14]
D0 [13]
D0[12]
D0 [11]
D0[10]
D0 [9]
D0 [8]
D0[7]
D0 [6]
D0 [5]
D0[4]
D 0[3]
D0 [2]
D0 [1]
ERR[0]
LSB
MSB
* ERR[15], ERR[14], … EER[0] are Error Message of LED Open Detection. `1'is normal, and `0'is abnormal.
16-channel 16-bit PWM Constant Current LED Driver
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 10
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Rising/Falling Edge Mode selection
The luminous data serial out from DAO by data clock (DCK) as following waveform. In rising
edge mode (REM), the data serial out by the rising edge of DCK.
256
1
2
255
256
DCK
DAO
D[255]
D[254]
D [253 ]
ERR[0]
E [255]
LAT
Rising Edge Mode (REM)
DAO serial out by DCK rising edge.
In falling edge mode (FEM), the data serial out by the falling edge of DCK.
256
1
2
255
256
DCK
DAO
D[255]
D[254]
ERR[0]
E [255]
LAT
Falling Edge Mode (FEM) :
DAO serial out by DCK falling edge.
*D[255], D[254],…D[0], E[255] are clock-in data in Shift data register of driver
16-channel 16-bit PWM Constant Current LED Driver
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 11
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
The default mode is the Rising-Edge Mode (REM*1) after power-on. Users could do mode
select between REM and FEM*2 by following timing sequence. The option 1 shows two rising edge
of latch pulses ( LAT ) when the data-input clock (DCK) kept at high level then sending one rising
edge of DCK pulses when LAT kept at high level. Then we can receive serial-out data from the
data-output signal (DAO) at falling edge of DCK after the falling edge of LAT . The option 2
shows three rising edge of LAT when DCK kept at high level then sending two rising edge of
DCK, while LAT kept high level at the same time. After the falling edge of LAT , we receive
serial-out data from DAO at rising edge of DCK (REM). Notice that when internal RESET at low
level, all the shift registers in DM632B will be cleared (Kept at Low level).
1
1
DCK
2
DCK
GCK
X
GCK
X
1
X
2
X
1
LAT
2
3
LAT
RESET
(internal)
RESET
(internal)
t
Option 1 : Timing Combination to set up
Falling-Edge Mode (FEM)
t
Option 2 : Timing Combination to set up
Rising-Edge Mode (REM)
Auto-Reload/One-Shot Mode selection
The Auto-Reload mode (ARM) in DM632B means outputs can repeat the grayscale PWM
cycle over and over. It can decrease the data amount greatly compare to non-PWM function driver
operated in grayscale PWM application.
Counter
reset
high
LAT
l ow
1
GCK
( internal or
external )
OUT0
(current)
0
65536 GCK
65536 GCK
on
Frame Data B
Frame Data B
off
Auto-Reload Mode (ARM).
The One-Shot Mode in DM632B means each output shows one grayscale PWM cycle
following one latch pulse. The grayscale PWM cycle starts with the falling edge of LAT signal.
The first GCK pulse after LAT increases the grayscale counter by one and switches on all outputs
with grayscale value. It makes driver synchronous control easily.
*1 REM switch to FEM timing diagram please refer to page 16.
*2 FEM switch to REM timing diagram please refer to page 17.
16-channel 16-bit PWM Constant Current LED Driver
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 12
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Counter
reset
high
LAT
l ow
1
GCK
( internal or
external )
65536 GCK
OUT0
Frame Data B
0
on
(current)
off
One-Shot Mode (OSM)
The default mode is the Auto-Reload Mode (ARM*1) after power-on. Users could do mode
select between ARM and One-Shot Mode (OSM*2 ) by following timing sequence. The gray scale
clock signal (GCK) should keep at low during this mode selection process. The option 1 shows four
rising edges of latch pulse ( LAT ) when the data-input clock (DCK) kept at high level then three
rising edges of DCK when LAT kept at high level. Then DM632B starts OSM after the falling
edge of LAT . The option 2 shows five rising edges of LAT when DCK kept at high level then
sending four rising edges of DCK signal, while LAT signal kept high level . After falling edge of
LAT , DM632B switch to ARM . Notice that when internal RESET at low level, all the shift
registers in DM632B will be cleared (Kept at Low level) .
1
2 3
1
DCK
GCK
2 3 4
DCK
X
GCK
X
1
2 3 4
X
X
1
LAT
2 3 4 5
LAT
RESET
(internal)
RESET
(internal)
t
Option 1 : Timing Combination to set up
One-Shot Mode (OSM)
*1
*2
t
Option 2 : Timing Combination to set up
Auto-Reload Mode (ARM)
ARM switch to OSM timing diagram please refer to page 18.
OSM switch to ARM timing diagram please refer to page 19.
16-channel 16-bit PWM Constant Current LED Driver
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 13
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Internal/External Clock Mode selection
Grayscale luminous of each channel comes from comparisons of grayscale PWM luminous
data and grayscale counter value. In internal-clock mode, DM632B provides build-in oscillator for
counter operation. In external-clock mode, the clock source of counter is from control system
through GCK pin. The default mode is the Internal-Clock Mode(ICM*1) after power-on. Users
could do mode select between ICM and External-Clock Mode (ECM∗2 ) by following timing
sequence. The option 1 shows four rising edges of latch pulses ( LAT ) when the data clock (DCK)
kept at high level and the grayscale clock (GCK) kept at low then sending three rising edges of DCK
when LAT and GCK both kept at high level. Then we can input external gray scale clock from
GCK pin to operate grayscale PWM function after the falling edge of LAT . The option 2 shows
five rising edges of LAT when DCK kept at high level and GCK at low level then sending four
rising edges of DCK , while LAT and GCK kept at high level . After the falling edge of LAT ,
grayscale PWM function operates by internal gray scale clock generator. Notice that when internal
RESET at low level, all the shift registers in DM632B will be cleared (Kept at Low level).
1
2
3
1
DCK
GCK
2
3
4
DCK
X
GCK
X
1
2
3
4
X
X
1
LAT
2
3
4 5
LAT
RESET
(internal)
RESET
(internal)
t
Option 1 :
Timing Combination to set up
External-Clock Mode (ECM)
t
Option 2 : Timing Combination to set up
Internal-Clock Mode (ICM)
LED Open Detection
DM632B provides a real time monitor of LED open detection function without extra
components or circuit design. It will be identified as a LED open failure when the output is turned
on but the output voltage is below 0.2V. The test result of each channel will write to its
correspondent shift register which is in LSB position (ERR[15], ERR[14], …., ERR[0]) while strobe
signal is active. User can refer to timing diagram on page11. Detecting report could be retrieved
from serial-out (DAO) data. If the system reads ‘1’ back, that indicates LED is in normal status. But
if ‘0’ was retrieved then LED open failure has occurred. In order to make sure LED open detection
function is in well operating condition, thold(L)*3 should larger then 360n sec(typ) due to the
build-in delay between outputs. And it is recommended that all the luminance data wrote to ‘1’
during detection.
*
1 ICM switch to ECM timing diagram please refer to page 20.
2 ECM switch to ICM timing diagram please refer to page 21
*
3 Hold time between LAT and DCK, please refer to page 15.
∗
16-channel 16-bit PWM Constant Current LED Driver
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 14
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Timing Diagram
1. DCK-DAI, DAO
tw DCK
tw DCK
50%
50%
50%
50%
DCK
t setup(D)
thold(D)
50%
50%
DAI
50%
DAO
50%
tpLH
tpHL
2. DCK-LAT
50%
50%
DCK
t setup(L)
t hold(L)
50%
50%
LAT
twLAT
3. GCK-OUT0
50%
50%
GCK
ON
50%
OUT0
50%
OFF
tpLH
tpHL
4. Output Delay Time Unit (N=0, 4, 8, 12)
ON
50%
OUT N
OFF
td
ON
50%
OUTN+1
OFF
td
ON
50%
OUTN+2
OFF
td
ON
OUTN+3
50%
OFF
16-channel 16-bit PWM Constant Current LED Driver
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 15
*3
*1
Frame Data I
Counter
reset
256
J [0]
ERR[ 0]*2
255
254
I [1]
J [1]
J [2]
Frame Data J
J [255]
Don'care
t
J [254 ]
Don'care
t
Mode switch period
1
L[255]
16-channel 16-bit PWM Constant Current LED Driver
LAT is level trigger, not edge trigger.
Iout turn off when LAT is high level ,and turn on at the first GCK rising edge when LAT is low level.
J[255],J[2],J[1],J[0],I[1],I[1],L[255].L[254],… L[0],M[255],M[254],… are serial data for DM632B.
*4
*5
256
L[ 0 ]
Frame Data L
1
M[255]
65536 GCK
*5
L [255]
Don'care
t
L [253]
3
M[253]
Frame Data L
L [254]
2
M[254]
Grayscale data clock-in period
*3
*1
2
L[254]
REM, ARM, IGM is configered by default. They can switch to FEM, OSM, EGM accordingly.
All registers in DM632B with be reset when any switch procees occur.
*2 ERR[0] is the error message of LED open detection.
(current )
OUTn*4
(internal)
GCK
(external)
GCK
LAT
DAO
DCK
DAI
Grayscale data clock-in period
L [252]
4
M[252]
off
on
l ow
high
0
1
l ow
high
0
1
low
high
0
1
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Timing Diagram (Rising-Edge Mode switch to Falling-Edge Mode)
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Version:PRE.001
Preliminary
Page 16
*3
*1
16-channel 16-bit PWM Constant Current LED Driver
ERR[ 0]*2
256
M[0]
Frame Data L
L [1]
255
254
L [2]
M[1]
M[2]
Counter
reset
M [255]
Frame Data M
Don'care
t
M[254 ]
Don'care
t
N [253 ]
Mode switch period
1
O[255]
M[255],M[254],… M[0],L[2],L[1],O[255].O[254],… O[0],P[255],P[254],… are serial data for DM632B.
*5
*4
LAT is level trigger, not edge trigger.
Iout turn off when LAT is high level ,and turn on at the first GCK rising edge when LAT is low level.
2
O[254]
256
O[0]
O[255]
Frame Data O
65536 GCK
Don'care
t
1
3
4
P [252]
O[252]*5
P [253]
O[253]
Frame Data O
2
P [254]
O[254]
P [255]
Grayscale data clock-in period
*3
*1
REM, ARM, IGM is configered by default. They can switch to FEM, OSM, EGM accordingly.
All registers in DM632B with be reset when any switch procees occur.
*2 ERR[0] is the error message of LED open detection.
(current )
OUTn*4
(internal)
GCK
(external)
GCK
LAT
DAO
DCK
DAI
Grayscale data clock-in period
off
on
l ow
high
0
1
l ow
high
0
1
low
high
0
1
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Timing Diagram (Falling-Edge Mode switch to Rising-Edge Mode)
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Version:PRE.001
Preliminary
Page 17
Frame Data C
256
D[0]
Frame Data D
65536 GCK
Counter
reset
D[255]
t care
Don'
Frame Data D
D[254]
t care
Don'
D[253]
Mode switch period
D[252]
1
F[255 ]
2
F [254]
256
F[0 ]
Frame Data F
Refresh Rate (Hz) =
Input GCK Frequency (Hz)
Total PWM resolution (216)
D[255],D[254],… D[0],F[255],F[254],...F[0],G[255],G[254],… are serial data for DM632B.
LAT is level trigger, not edge trigger.
Iout turn off when LAT is high level ,and turn on at the first GCK rising edge when LAT is low level.
Preliminary
*4
Version:PRE.001
*3
1
2
3
F [252]
G [253]
F [253]
G[254]
F [254]
G [255]
65536 GCK
Counter
reset
F[255] *5
t
Don'care
Grayscale data clock-in period
For example, if the refresh rate in display system is higher than 60Hz, the input GCK frequency must be higher than 4MHz.
16-channel 16-bit PWM Constant Current LED Driver
*5
*1
REM, ARM, IGM is configered by default. They can switch to FEM, OSM, EGM accordingly.
All registers in DM632B with be reset when any switch procees occur.
*2 ERR[0] is the error message of LED open detection.
(current)
OUTn*4
(internal)
GCK
(external)
GCK
LAT*3
DAO*1
DCK
DAI
Grayscale data clock-in period
off
on
l ow
high
0
1
l ow
high
0
1
low
high
0
1
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Timing Diagram (Auto-Reload Mode switch to One-Shot Mode)
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 18
*3
*1
16-channel 16-bit PWM Constant Current LED Driver
F[1]
256
255
Fr ame Data F
65536 GCK
ERR[0]*2
G[0]
G[1]
G[255]
t
Don'care
Fr ame Data G
G[254 ]
Don'care
t
G[253 ]
Mode switch period
G[253 ]
G[252 ]
LAT is level trigger, not edge trigger.
Iout turn off when LAT is high level ,and turn on at the first GCK rising edge when LAT is low level.
F[1],G[255],G[1],G[0],I[255],I[254],...I[0],J[255],J[254],… are serial data for DM632B.
*4
*5
1
I [255]
*3
*1
REM, ARM, IGM is configered by default. They can switch to FEM, OSM, EGM accordingly.
All registers in DM632B with be reset when any switch procees occur.
*2 ERR[0] is the error message of LED open detection.
(current )
OUTn*4
(inernal)
GCK
(external)
GCK
LAT
DAO
DCK
DAI
Grayscale data clock-in period
2
I [254]
256
I [0]
I [255]*5
Frame Data I
1
Frame Data I
2
J[254]
I [254]
J[255]
65536 GCK
Don'care
t
Grayscale data clock-in period
off
on
l ow
high
0
1
l ow
high
0
1
low
high
0
1
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Timing Diagram (One-Shot Mode switch to Auto-Reload Mode)
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Version:PRE.001
Preliminary
Page 19
*3
*1
16-channel 16-bit PWM Constant Current LED Driver
Frame Data O
ERR[ 0]*2
256
255
254
O[1]
P [0]
P [1]
P [2]
Counter
reset
P [255]
Don'care
t
Frame Data P
P [254 ]
P [253 ]
Don'care
t
Mode switch period
P [252 ]
1
Q[255]
P[255],P[254],… P[0],O[1],Q[255].Q[254],… Q[0],R[255],R[254],… are serial data for DM632B.
*5
*4
LAT is level trigger, not edge trigger.
Iout turn off when LAT is high level ,and turn on at the first GCK rising edge when LAT is low level.
2
Q[254]
256
Q [0]
*5
Q [255]
1
Frame DataQ
2
R[254]
Q[254]
R[255]
65536 GCK
Don'care
t
Grayscale data clock-in period
*3
*1
REM, ARM, IGM is configered by default. They can switch to FEM, OSM, EGM accordingly.
All registers in DM632B with be reset when any switch procees occur.
*2 ERR[0] is the error message of LED open detection.
(current )
OUTn*4
(internal)
GCK
(external)
GCK
LAT
DAO
DCK
DAI
Grayscale data clock-in period
l ow
high
l ow
high
0
1
l ow
high
0
1
low
high
0
1
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Timing Diagram (Internal-Clock Mode switch to External-Clock Mode)
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Version:PRE.001
Preliminary
Page 20
*3
*1
16-channel 16-bit PWM Constant Current LED Driver
Fr ame Data Q
ERR[ 0]*2
256
255
254
Q[1]
R[0]
R[1]
R[2]
Frame Data R
Counter
reset
R [255]
Don'care
t
R [254 ]
Don'care
t
R[253 ]
Mode switch period
R[253 ]
R[252 ]
1
S[255]
2
S[254]
*4
*3
256
S[0]
*5
S [255]
2
T[254]
S [254]
65536 GCK
1
T[255]
Frame Data S
Don'care
t
Grayscale data clock-in period
LAT is level trigger, not edge trigger.
Iout turn off when LAT is high level ,and turn on at the first GCK rising edge when LAT is low level.
*5
R[255],R[254],… R[0],S[255].S[254],… S[0],T[255],T[254],… are serial data for DM632B.
REM, ARM, IGM is configered by default. They can switch to FEM, OSM, EGM accordingly.
All registers in DM632B with be reset when any switch procees occur.
*2 ERR[0] is the error message of LED open detection.
*1
(current )
OUTn*4
(internal)
GCK
(external)
GCK
LAT
DAO
DCK
DAI
Grayscale data clock-in period
off
on
l ow
high
0
1
l ow
high
0
1
low
high
0
1
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Timing Diagram (External-Clock Mode switch to Internal-Clock Mode)
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Version:PRE.001
Preliminary
Page 21
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Output Modulation Technique
DM632B provides a new LED drive technique of output modulation. It mixes traditional Pulse
Width Modulation (PWM) represented by LSB 12 bit with Sequential Split Modulation (SSM)
represented by MSB 4 bit. The main benefits of SSM are to drive LED with an equivalent higher
refresh rate (up to 380Hzn in DM632B when FGCK = 25MHz) and change bit to next bit smoothly.
The relationships between PWM and SSM in time domain can be refer to the diagram (not to scale)
below:
Bit[11:0] (PWM)
Bit[15:0]
A complete modulation cycle
MSB
LSB
0000 XXXX,XXXXXXXX
MSB
LSB
on
off
Bit[7:0] (PWM)
Bit[11:8] (PWM)
on
0001 XXXX,XXXXXXXX
off
Bit[11:8] (PWM)
Bit[7:0] (PWM)
on
MSB
LSB
0110 XXXX,XXXXXXXX
off
Bit[11:0] (PWM)
Bit[7:0] (PWM)
on
MSB
LSB
0111 XXXX,XXXXXXXX
off
Bit[7:0] (PWM)
Bit[11:0] (PWM)
on
MSB
LSB
1000 XXXX,XXXXXXXX
off
Bit [7:0] (PWM)
Bit[11:0] (PWM)
on
MSB
LSB
1001 XXXX,XXXXXXXX
off
Bit[7:0] (PWM)
Bit[11:0] (PWM)
on
MSB
LSB
1110 XXXX,XXXXXXXX
off
Bit[7:0] (PWM)
Bit[11:0] (PWM)
on
MSB
LSB
1111 XXXX,XXXXXXXX
65536 clocks
off
t
Ultra High Resolution Current Outputs
DM632B could provide 16-bit linear PWM control current outputs for each channel. There are
two advantages for system design. One is DM632B has sufficient bit resolution (65536 steps), not
only LED color information but additional data such as global brightness, dot correction, and
gamma correction can be represented by the proper algorithms. The other is to reduce a lot of clock
and data rate compared to conventional ON-OFF type LED drivers.
16-channel 16-bit PWM Constant Current LED Driver
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 22
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Global Brightness Control
DM632B has no built-in global brightness control feature. In order to obtain a lower resolution
of global brightness control effect, two methods could be utilized. Here show different ways to
adjust the Rrext value or voltage drop across the external resistor. Please see the reference circuit
below:
Output to Output Delay
DM632B has build-in output to output delay with a special arrangement. This arrangement help
chip avoid noise cause by large current during channels switching. The arrangement details are
shown as following table.
Channel
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15
Delay units 0
1
2
3
0
1
2
3
0
1
16-channel 16-bit PWM Constant Current LED Driver
2
3
0
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
1
2
3
Preliminary
Page 23
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Power Dissipation
The power dissipation of a semiconductor chip is limited to its package and ambient
temperature, in which the device requires the maximum output current calculated for given
operating conditions. The maximum allowable power consumption can be calculated by the
following equation:
Pd(max)(Watt) =
Tj(junction temperature)(max)(°C)– Ta(ambient temperature)(°C)
Rth(junction-to-air thermal resistance)(°C/Watt)
The relationship between power dissipation and operating temperature can be refer to the figure
below:
PD - Ta curve
4.5
Tj(max)=150°C
Power Dissipation Pd(W)
4
TSSOP24E
Rth(TSSOP24E=30°C/Watt
3.5
Rth(SOP24B)=57°C/Watt
3
2.5
2
1.5
SOP24B
Rth(DIP24B)=67°C/Watt
DIP24B
Rth(SSOP24)=70°C/Watt
SSOP24
1
0.5
0
0
20
40
60
80
100
120
140
160
Ambient Temperature Ta ( ℃ )
The power consumption of IC can be determined by the following equation and should be less than
the maximum allowable power dissipation:
16-channel 16-bit PWM Constant Current LED Driver
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 24
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Typical Application
DM632B
DM632B
DM632B
DM632B
DM632B
DM632B
DM632B
16-channel 16-bit PWM Constant Current LED Driver
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 25
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Package Outline Dimension
DM632B-DIPB
13
1
12
A
A2
E
E1
24
E2
D
L
A1
SEATING PLANE
e
b1
b
DIMENSIONS IN INCH
SYMBOLS
MIN.
MAX.
DIMENSIONS IN MM
MIN.
MAX.
A
-
0.210
-
5.334
A1
0.015
-
0.381
-
A2
0.125
0.135
3.175
b
0.040
b1
D
E
0.018
0.457
0.880
0.920
22.352
0.300BSC
E1
0.245
E2
0.335
e
3.429
1.016
23.368
7.620BSC
0.255
6.223
0.375-
8.509
0.070
6.477
9.525
1.778
L
0.115
0.150
2.921
3.810
Θ
0°
15°
0°
15°
16-channel 16-bit PWM Constant Current LED Driver
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 26
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Package Outline Dimension
DM632B-SSOP
12
A
C
A2
1
SEATING PLANE
b
e
L
0.004
L1
DIMENSIONS IN INCH
MIN.
MAX.
MIN.
MAX.
A
0.053
0.069
1.346
1.753
A1
0.004
0.010
0.102
0.254
A2
-
0.059
-
1.499
b
0.008
0.012
0.203
0.305
C
0.007
0.010
0.178
0.254
D
0.337
0.344
8.560
8.738
E
0.228
0.244
5.791
6.198
E1
0.150
0.157
3.810
3.988
L
L1
Θ
0.025 BSC.
0.016
0.050
0.041 BSC
0°
16-channel 16-bit PWM Constant Current LED Driver
8°
DETAIL A
DIMENSIONS IN MM
SYMBOLS
e
A1
GAUGE PLANE
A
13
E
24
E1
D
0.635 BSC
0.406
1.270
1.041 BSC
0°
8°
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 27
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Package Outline Dimension
DM632B-SOPB
DIMENSIONS IN INCH
DIMENSIONS IN MM
SYMBOLS
MIN.
MAX.
MIN.
MAX.
A
-
0.075
-
1.900
A1
0.002
0.008
0.050
0.200
A2
0.051
0.067
1.300
1.700
b
0.012
0.020
0.300
0.500
c
0.004
0.010
0.100
0.250
D
0.504
0.520
12.800
13.200
E
0.303
0.327
7.700
8.300
e
0.0394 BSC
1.000 BSC
E1
0.228
0.244
5.800
6.200
L
0.010
0.026
0.250
0.650
θ
0°
10°
0°
10°
16-channel 16-bit PWM Constant Current LED Driver
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 28
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
Package Outline Dimension
DM632B-TSSOPE
(exposed pad)
D1
24
E2
E
E1
13
12
1
e
b
0.25mm
S
GAUGE PLANE
SEATING PLANE
A
A2
D
L
L1
A1
0.05
DIMENSIONS IN INCH
DIMENSIONS IN MM
SYMBOLS
MIN.
MAX.
MIN.
MAX.
A
-
0.047
-
1.20
A1
0.000
0.006
0.00
0.15
A2
0.031
0.041
0.80
1.05
b
0.007
0.012
0.19
0.30
D
0.303
0.311
7.70
7.90
E1
0.169
0.177
4.30
4.50
E
0.252 BSC
e
0.026 BSC
0.650 BSC
L1
0.039 REF
1.000 REF.
L
0.018
6.400 BSC
0.030
0.45
0.75
S
0.008
-
0.20
-
Θ
0°
8°
0°
8°
E2
0.0898
0.1122
2.280
2.850
D1
0.146
1.819
3.700
4.620
16-channel 16-bit PWM Constant Current LED Driver
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 29
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC.
新竹市科學園區展業一路 9 號 7 樓之 1
9-7F-1, Prosperity RoadⅠ, Hsin-Chu, Taiwan, R.O.C.
Tel:886-3-5645656
Fax:886-3-5645626
DM632B
The products listed herein are designed for ordinary electronic applications, such as
electrical appliances, audio-visual equipment, communications devices and so on. Hence,
it is advisable that the devices should not be used in medical instruments, surgical
implants, aerospace machinery, nuclear power control systems, disaster/crime-prevention
equipment and the like. Misusing those products may directly or indirectly endanger
human life, or cause injury and property loss.
Silicon Touch Technology, Inc. will not take any responsibilities regarding the misusage
of the products mentioned above. Anyone who purchases any products described herein
with the above-mentioned intention or with such misused applications should accept full
responsibility and indemnify. Silicon Touch Technology, Inc. and its distributors and all
their officers and employees shall defend jointly and severally against any and all claims
and litigation and all damages, cost and expenses associated with such intention and
manipulation.
16-channel 16-bit PWM Constant Current LED Driver
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Preliminary
Page 30