High Isolation Power Transformers EP7 Platform SMD Push Pull Converter Transformer Reinforced insulation for isolated power supply driver Compatible with MAXIM™ MAX253 to power RS-485/RS232 transceiver and other communication interfaces 8mm creepage, 5KVrms isolation UL and TUV certification 4 Electrical Specifications @ 25°C - Operating Temperature -40°C to +125°C Inductance (1-3) (µH ±45%) DCR (1-3) 1 (Ω MAX) DCR (4-6) (Ω MAX) MAX (1-3) 1 (V-µsec Max) Turns Ratio (1:3) (6:4) PH9185.011NL 750 0.50 0.55 66 1CT : 1CT PH9185.012NL 450 0.40 0.80 52 1CT : 2CT PH9185.013NL 200 0.35 0.95 36 1CT : 3CT PH9185.021NL 1800 0.75 0.45 100 2CT : 1CT PH9185.034NL 750 0.50 0.75 66 3CT : 4CT PH9185.038NL 310 0.44 1.00 44 3CT : 8CT PH9185.043NL 1260 0.70 0.56 89 4CT : 3CT PH9185.083NL 2350 0.90 0.40 110 8CT : 3CT Part 2, 3, 4 Number Notes: 1. The maximum volt-usec rating limits the peak flux density to 3600 gauss when used in bi-polar drive application with 200KHz. For unipolar drive applications or a bi-polar drive with 350kHz, a maximum volt-usec could be 60% of the listed value. For Push-Pull topology, where the voltage is applied across half the primary winding turns, the maximum volts-use needs to be derated by 50%. 2. PH9185.13NL not UL/TUV certified PH9185.XXXXNL Schematic 4 4 6 1 .100[2.54] PH9185.XXXNL .100X2[2.54X2] .370 [9.40] R C US E119132 F2 DATE CODE .520 [13.21] Secondary Primary Secondary 5 3 3 1 6 Primary 2 .047[1.20] CTRY MFG 1 4 3 SCHEMATIC SUGGESTED LAND PATTERN (.394) ([10.00]) .394MAX[10.00] 1 2X.100[2.54] =.200±.008[5.08±.20] 3 .079 REF [2.00] REF USA 858 674 8100 1 3 .100±.008 [2.54±.20] .079 REF [2.00] REF Germany 49 7032 7806 0 1 (.378) [9.60] .512 MAX [13.00 MAX] Singapore 65 6287 8998 pulseelectronics.com Weight ...................2.6grams Tape & Reel ...............150/reel Tray .............................80/tray Dimensions: Inches mm Unless otherwise specified, all tolerances are ± .010 0,25 .492 MAX [12.50 MAX] .016±.002 [.40±.05] 5000 3. Optional Tape & Reel packing can be ordered by adding a “T” suffix to the part number (i.e. PH9185.012NL becomes PH9185.012NLT). Pulse complies to industry standard tape and reel specification EIA481. 4. The “NL” suffix indicates an RoHS-compliant part number. 5. The temperature of the component (ambient plus the temperature rise) must be within the stated operating temperature range. Mechanical 6 Isolated Voltage (Vrms) .005[.13] 6 PLACES 6 Shanghai 86 21 62787060 4 China 86 755 33966678 Taiwan 886 3 4356768 P708.D (03/15) High Isolation Power Transformers EP7 Platform SMD Application PH9185NL is a series of high isolation power supply transformer drivers. Intended to operate in a fixed duty cycle Push Pull topology, it is a part of a low cost solution for delivering lower power (up to 3W) from a low voltage source. A typical implementation would be an isolated RS-485/RS-232 power supply driver circuit, the design is compatible with the MAXIM™ MAX253 IC. A schematic diagram for the Push Pull converter topology is given below. VIN PH9185 VCC D1 V OUT DRIVER IC D2 GND For a fixed 50% duty cycle mode of operation, the output voltage is simply determined by the input voltage and turns ratio. So, with the available turns ratios, a variety of output voltages can be selected. This transformer design has been certified by UL to comply with UL60950-1 2nd edition, and CAN/CSA C22.2 NO. 60950-1-07 2 ndedition; and by TUV to comply with EN61558-1 and EN61558-2-16 with reinforced insulation for a working voltage up to 400V 8mm creepage and 5000Vrms isolation voltage is guaranteed to meet this requirement. The design also complies with the Pulse’s class F insulation system. Cost reduced versions without UL/TUV certification available, please contact Pulse Electronics for more information. MAXIM is a registered trademark of Maxim Integrated Products. For More Information Pulse Worldwide Headquarters 12220 World Trade Drive San Diego, CA 92128 U.S.A. Pulse Europe Einsteinstrasse 1 D-71083 Herrenberg Germany Pulse China Headquarters Pulse North China Pulse South Asia Pulse North Asia B402, Shenzhen Academy of Room 2704/2705 135 Joo Seng Road 3F, No. 198 Aerospace TechnolSuper Ocean Finance #03-02 Zhongyuan Road ogy Bldg. Ctr. PM Industrial Bldg. Zhongli City 10th Kejinan Road 2067 Yan An Road Singapore 368363 Taoyuan County 320 High-Tech Zone West Taiwan R. O. C. Nanshan District Shanghai 200336 Tel: 886 3 4356768 Shenzen, PR China China Tel: 65 6287 8998 Fax: 886 3 4356823 (Pulse) Tel: 858 674 8100 Tel: 49 7032 78060 518057 Fax: 65 6287 8998 Fax: 886 3 4356820 (FRE) Fax: 858 674 8262 Fax: 49 7032 7806 135 Tel: 86 755 33966678 Tel: 86 21 62787060 Fax: 86 755 33966700 Fax: 86 2162786973 Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. © Copyright, 2015. Pulse Electronics, Inc. All rights reserved. 2 pulseelectronics.com P708.D (03/15)