规格书编号 SPEC NO : 产品 规 格书 SPECIFICATION CUSTOMER 客 户： PRODUCT 产 品： SAW FILTER MODEL NO 型 号： HDF165M SMD-4 MARKING 印 字： HDF4165 PREPARED 编 制： CHECKED 审 核： APPROVED 批 准： D A T E 日 期： 2009-03-03 客户确认 CUSTOMER RECEIVED: 审核 CHECKED 批准 APPROVED 日期 DATE 无锡市好达电子有限公司 Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 1 of 9 SAW FILTER HDF165M S-4 更改历史记录 History Record 更改日期 Date www.shoulder.cn 规格书编号 Spec. No. 产品型号 Part No. 客户产品型号 Customer No. Tel:0755-82916880 Fax:0755-82916881 更改内容描述 Modify Content E-mail:[email protected] 备注 Remark Page 2 of 9 SAW FILTER HDF165M S-4 1. SCOPE This specification shall cover the characteristics of SAW filter With HDF165M used for the page system. 2. ELECTRICAL SPECIFICATION Parameter Operating Temperature Range Storage Temperature DC Voltage Max. Input CW Power (Continuous stress) Ratings -40 ~ 85 ℃ -50 ~ 125 ℃ 0V 25 dBm 2-1. Electrical characteristics Parameter Center Frequency ( f0 ) Pass Bandwidth Insertion Loss (Passband) Insertion Loss (Passband) Variation Over Operating Temperature Range Passband Ripple (Passband) From 10 MHz to 110MHz From 127 MHz to 149MHz From 190MHz to 450MHz Absolute Delay at Passband Group Delay Variation (Passband) Input Impedance Output Impedance Input Return Loss Output Return Loss Operating Temperature Range www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 Min 20 Typ 165 22 9 Max 10 1 35 10 35 9.0 9.0 -40 E-mail:[email protected] 0.8 40 15 40 0.33 40 50 50 12.0 12.0 25 1.2 Units MHz MHz dB dB dB p-p dBc 80 85 us ns p-p ohm ohm dB dB ℃ Page 3 of 9 SAW FILTER HDF165M S-4 2-2. Typical frequency response 3.TEST CIRCUIT L1 = 150nH , L2 = 68nH C1 = 15pF , C2 = 6.8pF www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 4 of 9 SAW FILTER HDF165M S-4 3. DIMENSION Marking：HDF4165 HD: Brand F : Filter 4 : SMD-4 165 : No. 5. ENVIRONMENTAL CHARACTERISTICS 5-1 Temperature cycling Subject the device to a low temperature of -45℃ for 30 minutes. Following by a high temperature of +25℃ for 5 Minutes and a higher temperature of +85℃ for 30 Minutes. Then release the device into the room conditions for 1 to 2 hours prior to the measurement. It shall meet the specifications in 2-1. 5-2 Resistance to solder heat Submerge the device terminals into the solder bath at 260℃ ±5℃ for 10±1 sec. Then release the device into the room conditions for 4 hours. It shall meet the specifications in 2-1. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 5 of 9 SAW FILTER HDF165M S-4 5-3 Solderability Submerge the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95% area of the soldering pad must be covered with new solder. It shall meet the specifications in 2-1. 5-4 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1 m 3 times. the filter shall fulfill the specifications in 2-1. 5-5 Vibration Subject the device to the vibration for 2 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. The filter shall fulfill the specifications in 2-1. 6. REMARK 6.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 6.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 6.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component. 7. Packing 7.1 Dimensions (1) Carrier Tape: Figure 1 (2) Reel: Figure 2 (3) The product shall be packed properly not to be damaged during transportation and storage. 7.2 Reeling Quantity 1000 pcs/reel 7’’ 3000 pcs/reel 13’’ 7.3 Taping Structure (1) The tape shall be wound around the reel in the direction shown below. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 6 of 9 SAW FILTER HDF165M S-4 (2) Label Device Name User Product Name Quantity Lot No. (3) Leader part and vacant position specifications. 8. TAPE SPECIFICATIONS 8.1 Tensile Strength of Carrier Tape: 4.4N/mm width 8.2 Top Cover Tape Adhesion (See the below figure) (1) pull off angle: 0~15º (2) speed: 300mm/min. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 7 of 9 SAW FILTER HDF165M S-4 (3) force: 20~70g [Figure 1] Carrier Tape Dimensions [Unit:mm] W F E P0 P1 P2 D0 D1 t1 t2 A B 12.00 ±0.30 5.50 ±0.10 1.75 ±0.10 4.00 ±0.10 8.00 ±0.10 2.00 ±0.10 Ø1.50 Ø1.0 ±0.25 0.25 ±0.05 1.65 ±0.10 4.04 ±0.10 4.10 ±0.10 [Figure 2] www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 8 of 9 SAW FILTER HDF165M S-4 [Unit:mm] www.shoulder.cn A B C D E W t r Ø330 ±1.0 Ø100 ±0.5 Ø13 ±0.5 Ø21 ±0.8 2 ±0.5 13 ±0.3 3 max. 1.0 max. Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 9 of 9