SHOULDER ELECTRONICS LIMITED CERAMIC FILTER Data Sheet PRODUCT 产 品: CERAMIC MODEL NO 型 号: LTM…W PREPARED 编 制: Fengyu CHECKED 审 核: York APPROVED 批 准: Lijiating DATE Http://www.shoulder.cn 日 期: FILTER 2008-01-25 Page: 1 SHOULDER ELECTRONICS LIMITED 1. LTM 455(450)…W SERIES Part Number Center Insertion Pass Band 6dB 40dB Stop Band Att. I/O Frequency Loss Ripple Bandwidth Bandwidth ±100 KHz Impedance min max min (KHz) (dB) (dB) (KHz) (KHz) (dB) (Ohm) LTM450BU 450±2.0 4 2 ±15 ±30 40 1500 LTM455BW 455±2.0 4 2 ±15 ±30 40 1500 LTM450CW 450±2.0 4 2 ±12.5 ±24 40 1500 LTM455CW 455±2.0 4 2 ±12.5 ±24 40 1500 LTM450DW 450±1.5 4 2 ±10 ±20 40 1500 LTM455DW 455±1.5 4 2 ±10 ±20 40 1500 LTM450EW 450±1.5 6 2 ±7.5 ±15 40 1500 LTM455EW 455±1.5 6 2 ±7.5 ±15 40 1500 LTM450FW 450±1.5 6 2 ±6 ±12.5 40 2000 LTM455FW 455±1.5 6 2 ±6 ±12.5 40 2000 LTM450GW 450±1.5 6 2 ±4.5 ±10 40 2000 LTM455GW 455±1.5 6 2 ±4.5 ±10 40 2000 LTM450HW 450±1.0 6 2 ±3 ±9 40 2000 LTM455HW 455±1.0 6 2 ±3 ±9 40 2000 LTM450IW 450±1.0 6 2 ±2 ±7.5 40 2000 LTM455IW 455±1.0 6 2 ±2 ±7.5 40 2000 LTM450HTW 450±1.0 6 2 ±3 ±9 60 2000 LTM455HTW 455±1.0 6 2 ±3 ±9 60 2000 2. PART NUMBERING : LTM455HTW 3. ELECTRONICAL SPECIFICATIONS A. CENTRE FREQUENCY (f。) : B. BAND WIDTH AT 6 dB : C. BAND WIDTH AT 50 dB : D. STOP BAND ATTENUATION : E. RIPPLE : F. INSERTION LOSS : G. TEMPRATURE COEFFICIENT OF CENTER FRENQUENCY : 455KHz±1.0KHz. ±3.0 KHz MIN.(TO 455KHz) ±9.0 KHz MAX.(TO 455KHz) 45.0 dB MIN.(AT f。±100KHz) 2.0 dB MAX.(AT f。±5.0KHz) 5.0 dB MAX (AT THE SMALLEST LOSS) ±50PPM/℃ Max.(-20 TO +80℃) H. INPUT/OUTPUT IMPEDANCE : 1.5KΩ NOTE : A) CENTER FREQUENCY SHALL BE DEFIED AS THE CENTRAL VALUE OF THE BAND WITH AT 6 dB B) TEMPRATURE COEFFICIENT OF CENTER FREQUENCY SHALL BE DEFINED AS THE AVERAGE OF THE CENTRAL FREQUECY. 4. MEASUREMENT A. ENVIRONMENTAL CONDITION MEASUREMENT SHALL BE Http://www.shoulder.cn CARRIED OUT AT THE REFERENCE Page: 2 SHOULDER ELECTRONICS LIMITED TEMPERATURE OF 25℃ ±2℃. IT SHALL AT 5℃TO 35℃UNLESS IT IS QUESTIONABLE. B. MEASURING CIRCUIT BE POSSIBLY DONE #S.S.G. (STANDARD SIGNAL GENERATION) R.F.V.M. (RADIO FREQUENCY VOLTAGE METER) Rg+R1=R2=1.5 KΩ C<=50 PF 5. DIMENSIONS(mm) 6. ENVIRONMENTAL CHARACTERISTICS 6-1 HIGH TEMPERATURE EXPOSURE SUBJECT THE FILTER TO +80℃ FOR 96 HOURS. THEN RELEASE THE FILTER INTO THE ROOM CONDITIONS FOR 2 HOURS PRIOR TO THE MEASUREMENT. IT SHALL FULFILL THE SPECIFICATIONS IN TABLE 1. 6-2 MOISUTRE KEEP THE FILTER AT 40℃ AND 95% RH FOR 96 HOURS.THEN RELEASE THE FILTER INTO THE ROOM CONDITIONS FOR 2 HOURS PRIOR TO THE MEASUREMENT. IT SHALL FULFILL THE Http://www.shoulder.cn Page: 3 SHOULDER ELECTRONICS LIMITED 6-3 6-4 6-5 6-6 6-7 6-8 SPECIFICATIONS IN TABLE 1. LOW TEMPERATURE EXPOSURE SUBJECT THE FILTER TO -20℃ FOR 96 HOURS. THEN RELEASE THE FILTER INTO THE ROOM CONDITIONS FOR 2 HOURS PRIOR TO THE MEASUREMENT. IT SHALL FULFILL THE SPECIFICATIONS IN TABLE 1. TEMPERATURE CYCLING SUBJECT THE FILTER TO A LOW TEMPERATURE OF -20℃ FOR 30 MINUTES. FOLLOWSING BY A HIGH TEMPERATURE OF +80℃ FOR 30 MINUTES. THEN RELEASE THE FILTER INTOTHE ROOM CONDITIONS FOR 2 HOURS PRIOR TO THE MESUREMENT. IT SHALL MEET THE SPECIFICATIONS IN TABLE 1. RESISTANCE TO SOLDER HEAT DIP THE FILTER TERMINALS NO CLOSER THAN 1.5mm INTO THE SOLDER BATH AT 260℃ ±10℃ FOR 10±1 SEC. THEN RELEASE THE FILTER INTO THE ROOM CONDITIONS FOR 2 HOURS. THE FILTER SHALL MEET THE SPECIFICATIONS IN TABLE 1. MECHANICAL SHOCK DROP THE FILTER RANDOMLY ONTO THE CONCRETE FLOOR FROM THE HEIGHT OF 30cm 3 TIMES.THE FILTER SHALL FULFILL THE SPECIFICATIONS IN TABLE 1. VIBRATION SUBJECT THE FILTER TO THE VIBRATION FOR 1 HOUR EACH IN X,Y AND Z AXES WITH THE AMPLITUDE OF 1.5 mm AT 10 TO 55 Hz. THE FILTER SHALL FULFILLTHE SPECIFICATIONS IN TABLE 1. LEAD FATIGUE 6-8-1 PULLING TEST WEIGHT ALONG WITH THE DIRECTION OF LEAD WITHOUT AN SHOCK 3 KG. THE FILTER SHALL SATISFY ALL THE INITIALL CHARACTERISTICS. 6-8-2 BENDING TEST LEAD SHALL BE SUBJECT TO WITHSTAND AGAINST 90° BENDING IN THE DERECTION OF THICKNESS. THIS OPERATION SHALL BE DONE TOWARD BOTH DIRECTION. THE FILTER SHALL SHOW NO EVIDENCE OF DAMAGE AND SHALL SATISFY ALL THE INITIAL ELECTRICAL CHARACTERISTICS. TABLE 1 ITEM CENTRE FREQUENCY(f。) BAND WIDTH(6 dB) SELECTIVITY(40dB) STOP BAND ATTENUATION RIPPLE INSERTION LOSS Http://www.shoulder.cn SPECIFICATION 455±1.0 KHz ±3.0 KHz Min ±9.0 KHz Max 60.0 dB Min 2.0 dB Max 6.0 dB Max Page: 4 SHOULDER ELECTRONICS LIMITED