ARINC 600 Backshells 527-108 EMI/RFI Banding Backshell for Size 3 ARINC 600 Series Connector 527-108 NF P A4 B4 C4 D4 E4 F4 B Basic Part No. B = Band(s) Supplied 600-052, One Per Entry Location, Omit for None Finish (Table II) Position and Dash No. (Table I) Omit Unwanted Positions Connector Designator (Table III) Shield Termination Area Typ. Position E Position C 1.60 (40.6) 1.50 (38.1) A Position F 3.25 (82.6) Position D 5.61 (142.5) Position B Position A Entry Dia (Typ) Jam Nut (Typ) A View A-A Metric dimensions (mm) are indicated in parentheses. © 2004 Glenair, Inc. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com E-Mail: [email protected] F-18 ARINC 600 Backshells 527-108 EMI/RFI Banding Backshell for Size 3 ARINC 600 Series Connector TABLE I: CABLE ENTRY Dash Entry No. Dia 4 .50 (12.7) 5 .63 (16.0) 6 .75 (19.1) 7 .88 (22.4) 8 1.00 (25.4) 9 1.13 (28.7) TABLE II: FINISH OPTIONS Symbol B C* G* J LF M N Finish Symbol Finish Cadmium Plate/Olive Drab NC Zinc Cobalt/Dark Olive Drab Black Anodize NF Cadmium Plate/Olive Drab over Anodic Hard Coat Electroless Nickel Gold Iridite over Cadmium Plate T Cadmium Plate/Bright over over Electroless Nickel Electroless Nickel Cadmium Plate/Bright over U** Cadmium Plate/Black Electroless Nickel ZN Zinc-Nickel Alloy/Olive Drab *Anodize finish is not suitable for EMI shielding or grounding Electroless Nickel Cadmium Plate/Olive Drab over applications. **Applicable to corrosion resisting steel backshells and Electroless Nickel accessories. Consult factory for other available finishes. TABLE III: CONNECTOR DESIGNATOR ARINC 600 series connector backshells are designed to replace the insert retainer plates. Due to non-standard modifications by the connector manufacturer, the backshell may require special design alterations to mate properly. The following should be used to determine if a backshell modification is required. Prior to ordering, consult factory with connector part numbers not shown to ensure a proper fit. Connector Designator Connector Description P All Manufacturer’s Plug and Receptacle Shells, Except for Those Listed Below (Prior to ordering, consult factory with connector part numbers not listed below to ensure a proper fit.) P1 P2 Cannon BKAD****322 Series Plug P3 Cannon/Boeing BACC 66 Plug P5 Radiall/Boeing BACC66 Plug P6 Cannon BKAC & BKAE XXX322 Series Environmental Plug Cannon/Radiall Environmental Plug 1. Metric dimensions (mm) are indicated in parentheses. 2. Material/Finish: Backshell, Fittings, Nuts, Clamps = Al Alloy/See Table II; Hardware = SST/Passivate © 2004 Glenair, Inc. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com E-Mail: [email protected] F-19