EVALUATION KIT AVAILABLE MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface General Description The MAX6650/MAX6651 fan controllers use an SMBus/I2C-compatible interface to regulate and monitor the speed of 5VDC/12VDC brushless fans with builtin tachometers. They automatically force the fan’s tachometer frequency (fan speed) to match a preprogrammed value in the Fan-Speed Register by using an external MOSFET or bipolar transistor to linearly regulate the voltage across the fan. The MAX6650 regulates the speed of a single fan by monitoring its tachometer output. The MAX6651 also regulates the speed of a single fan, but it contains additional tachometer inputs to monitor up to four fans and control them as a single unit when they are used in parallel. The MAX6650/MAX6651 provide general-purpose input/output (GPIO) pins that serve as digital inputs, digital outputs, or various hardware interfaces. Capable of sinking 10mA, these open-drain inputs/outputs can drive an LED. To add additional hardware control, configure GPIO1 to fully turn on the fan in case of software failure. To generate an interrupt when a fault condition is detected, configure GPIO0 to behave as an activelow alert output. Synchronize multiple devices by setting GPIO2 (MAX6651 only) as an internal clock output or an external clock input. ____________________________Features ♦ Closed/Open-Loop Fan-Speed Control for 5V/12V Fans ♦ 2-Wire SMBus/I2C-Compatible Interface ♦ Monitors Tachometer Output Single Tachometer (MAX6650) Up to Four Tachometers (MAX6651) ♦ Programmable Alert Output ♦ GPIOs ♦ Hardware Full-On Override ♦ Synchronize Multiple Fans ♦ Four Selectable Slave Addresses ♦ 3V to 5.5V Supply Voltage ♦ Small Packages 10-Pin µMAX (MAX6650) 16-Pin QSOP (MAX6651) Ordering Information PART TEMP RANGE PIN-PACKAGE MAX6650EUB -40°C to +85°C 10 µMAX MAX6650EUB+ -40°C to +85°C 10 µMAX MAX6651EEE -40°C to +85°C 16 QSOP MAX6651EEE+ -40°C to +85°C 16 QSOP The MAX6650 is available in a space-saving 10-pin µMAX® package, and the MAX6651 is available in a small 16-pin QSOP package. +Denotes a lead(Pb)-free/RoHS-compliant package. ________________________Applications Pin Configurations appear at end of data sheet. RAID Desktop Computers Servers Networking Workstations Telecommunications µMAX is a registered trademark of Maxim Integrated Products, Inc. Typical Operating Circuit VFAN 5V OR 12V VCC VCC 3V TO 5.5V 10kΩ MAX6650 SMBus/I2C INTERFACE SCL TACH0 SDA FB FAN LED ALERT FULL ON GPIO0 OUT GPIO1 ADD CCOMP 10μF GND For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com. 19-1784; Rev 5; 12/12 MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface ABSOLUTE MAXIMUM RATINGS VCC to GND ..............................................................-0.3V to +6V FB, TACH_ ..........................................................-0.3V to +13.2V All Other Pins..............................................-0.3V to (VCC + 0.3V) Output Voltages..........................................-0.3V to (VCC + 0.3V) Maximum Current Into VCC, GND, VOUT ...................................................100mA Into All Other Pins ..........................................................50mA Continuous Power Dissipation (TA = +70°C) µMAX (derate 5.6mW/°C above +70°C) .....................444mW QSOP (derate 8.3mW/°C above +70°C) .....................667mW Operating Temperature Range ...........................-40°C to +85°C Junction Temperature .....................................................+150°C Storage Temperature Range .............................-65°C to +150°C Lead Temperature (soldering, 10s) .................................+300°C Soldering Temperature (reflow) Lead(Pb)-free..............................................................+260°C Containing lead(Pb) ....................................................+240°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VCC = 3.0V to 5.5V, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C and VCC = 5V.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS POWER SUPPLY (VCC) Supply Voltage VCC Supply Current ICC 3.0 Full-on mode, IOUT = 0 5.5 V 10 mA OUTPUT (OUT) Output Voltage Range VOUT IOUT = ±100µA 0.3 Output Sink Current ISINK VOUT = 0.5V 10 mA VOUT = VCC - 1.8V 50 mA Output Source Current ISOURCE VCC - 0.3 V TACHOMETER INPUTS (TACH_) Tachometer Threshold VTACH_ Tachometer Input Impedance RTACH_ 5V fan, 0 < VFB < 4.5V VFB + 0.5 VFB +1.5 12V fan, 0 < VFB < 9V VFB + 1.0 VFB +3 0 < VTACH < 9V 70 100 V 150 kΩ FEEDBACK (FB) DAC Differential Nonlinearity Guaranteed monotonicity on FB (Note 1) 5 LSB Useful DAC Resolution Measured at FB (Note 1) 8 bits 150 kΩ 0.8 V Feedback Input Impedance RFB 0 < VFB < 9V 70 100 GENERAL-PURPOSE INPUTS/OUTPUTS (GPIO_) (Note 2) Input Low Voltage Input High Voltage VIL(GPIO_) VIH(GPIO_) VCC ≤ 3.6V 2 VCC > 3.6V 3 V Input Hysteresis VHYS 200 mV Pullup Resistor RGPIO_ 100 kΩ Output Sink Current IGPIO_ 2 VGPIO_ = 0.4V 10 mA Maxim Integrated MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface ELECTRICAL CHARACTERISTICS (continued) (VCC = 3.0V to 5.5V, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C and VCC = 5V.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 0.1 V ADDRESS SELECT (ADD) ADD Input Low Voltage VIL(ADD) Selects slave address 90h (Table 1) ADD Input High Voltage VIH(ADD) Selects slave address 96h (Table 1) VCC - 0.05 V ADD Input Leakage ILADD Selects slave address 36h (Table 1) (Note 3) -1 0 µA ADD External Pulldown Resistor to GND RADD Selects slave address 3Eh (Table 1) 9.5 10.5 kΩ ADD Pulldown Current IADD VADD = 0.5V (Note 4) -80 -40 µA ISDA VSDA = 0.6V SMBus/I2C INTERFACE (SDA, SCL) Data Output Sink Current Input Leakage Current Input Low Voltage Input High Voltage Input Hysteresis 6 mA 0 < VIN < VCC VIL VIH VCC ≤ 3.6V 2 VCC > 3.6V 3 VHYS ±1 µA 0.8 V V 200 mV TIMING CHARACTERISTICS (VCC = 3.0V to 5.5V, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C and VCC = 5V.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS TACHOMETERS Glitch Rejection Minimum pulse duration 500 µs GPIO2 (Note 2) Clock Frequency fCLK Clock Frequency Uncertainty fCLK 254 VCC = 5V kHz -10 +10 % 0 400 kHz SMBus/I2C INTERFACE (Figures 3, 4) SCL Clock Frequency fSCL Bus Free Time Between Stop and Start Condition tBUF 1.3 µs tHD:STA 0.6 µs Low Period of the SCL Clock tLOW 1.3 µs High Period of the SCL Clock tHIGH 0.6 Hold-Time Start Condition Data Hold Time tHD:DAT Data Setup Time tSU:DAT (Note 5) 0 µs 900 100 µs ns Rise-Time SDA/SCL Signal (Receiving) tR (Note 6) 20 + 0.1CB(pF) 300 ns Fall-Time SDA/SCL Signal (Receiving) tF (Note 6) 20 + 0.1CB(pF) 300 ns Fall-Time SDA Signal (Transmitting) tF ISINK < 6mA (Note 6) 20 + 0.1CB(pF) 250 ns Maxim Integrated 3 MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface TIMING CHARACTERISTICS (continued) (VCC = 3.0V to 5.5V, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C and VCC = 5V.) PARAMETER SYMBOL Setup Time for Stop Condition Pulse Width of Spike Suppressed CONDITIONS MIN tSU:STO 0.6 tSPIKE 0 TYP MAX UNITS µs 50 ns For proper measurement of VFB, connect OUT and FB as shown in the Typical Operating Circuit. GPIO2, GPIO3, and GPIO4 only in the MAX6651. Guaranteed by design and not 100% production tested. For RADD component test purposes only. Note that the transition must internally provide at least a hold time to bridge the undefined region (300ns max) of SCL’s falling edge. Note 6: CB is the total capacitance of one bus line in pF. Tested with CB = 400pF. Rise and fall times are measured between 0.3 x VCC and 0.7 x VCC. Note 1: Note 2: Note 3: Note 4: Note 5: Typical Operating Characteristics (TA = +25°C, unless otherwise noted.) INTERNAL OSCILLATOR FREQUENCY vs. SUPPLY VOLTAGE VCC = 5.5V 260 240 VCC = 3.0V MAX6650/51-03 2.3 VCC = 5.5V, VFAN = 5.5V, VFAN = 12.0V 2.2 2.1 2.0 VFAN = 12.0V, VFAN = 5.5V VCC = 3.0V 220 245 1.9 3.5 4.0 4.5 5.0 0 50 SUPPLY VOLTAGE (V) TEMPERATURE (°C) FEEDBACK VOLTAGE vs. SUPPLY VOLTAGE (DAC SET TO 35) SUPPLY CURRENT vs. SUPPLY VOLTAGE VFAN = 5.5V 2.05 VFAN = 12.0V 2.00 3.6 SUPPLY CURRENT (mA) 2.10 1.95 3.4 2.8 2.6 1.85 2.2 3.0 3.5 4.0 4.5 SUPPLY VOLTAGE (V) 5.0 5.5 4.0 VCC = 5.5V 3.5 3.0 2.5 VCC = 3V 2.0 2.0 1.80 100 50 SUPPLY CURRENT vs. TEMPERATURE 3.0 2.4 0 TEMPERATURE (°C) 3.2 1.90 -50 100 SUPPLY CURRENT (mA) 2.15 3.8 MAX6650/51-04 2.20 FEEDBACK VOLTAGE (V) -50 5.5 MAX6650/51-05 3.0 4 1.8 200 240 MAX6650/51-06 250 2.4 FEEDBACK VOLTAGE (V) 255 2.5 MAX6650/51-02 280 FREQUENCY (kHz) 260 FREQUENCY (kHz) 300 MAX6650/51-01 265 FEEDBACK VOLTAGE vs. TEMPERATURE INTERNAL OSCILLATOR FREQUENCY vs. TEMPERATURE 1.5 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 SUPPLY VOLTAGE (V) -40 -20 0 20 40 60 80 100 TEMPERATURE (°C) Maxim Integrated MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface Pin Description PIN PIN NAME FUNCTION MAX6650 MAX6651 1 1 TACH0 — 2, 3, 16 TACH2, TACH3, TACH1 2 4 GND Ground 3 5 SDA 2-Wire Serial-Data Input/Output (open drain) 4 6 SCL 2-Wire Serial Clock Input 5 8 ADD Slave Address Select Input (Table 1) — 7, 12 GPIO4, GPIO3 6 9 GPIO1 General-Purpose Input/Output (open drain). Configurable to act either as an output or as an input (FULL ON or general purpose). 7 10 GPIO0 General-Purpose Input/Output (open drain). Configurable to act as a general input/output line or an active-low ALERT output. — 11 GPIO2 General-Purpose Input/Output (open drain). Configurable to act as a general input/output line, an internal clock output, or an external clock input. 8 13 OUT Output. Drives the external MOSFET or bipolar transistor. 9 14 VCC +3.0V to +5.5V Power Supply 10 15 FB Tachometer Input. Used to close the loop around the tachometer. Tachometer Inputs. Used to monitor tachometers only. General-Purpose Input/Output (open drain) Feedback Input. Closes the loop around the external MOSFET or bipolar transistor. Detailed Description The MAX6650/MAX6651 use an SMBus/I2C-Compatible interface to regulate and monitor the speed of 5VDC/12VDC brush-less fans with built-in open-collector/drain tachometers. Regulating fan speed proportionally with temperature saves power, increases fan life, and reduces acoustic noise. Since fan speed is proportional to the voltage across the fan, the MAX6650/MAX6651 control the speed by regulating the voltage on the low side of the fan with an external MOSFET or bipolar transistor. The MAX6650/MAX6651 each contain two internal control loops. The first loop controls the voltage across the fan. The internal digital-to-analog converter (DAC) sets the reference voltage for an internal amplifier (Figure 1), which then drives the gate of an external N-channel MOSFET (or the base of a bipolar transistor) to regulate the voltage on the low side of the fan. As the reference voltage provided by the DAC changes, the feedback amplifier automatically adjusts the feedback voltage, which changes the voltage across the fan. Maxim Integrated The second control loop consists of the internal digital logic that controls the fan’s speed. The MAX6650/ MAX6651 control fan speed by forcing the tachometer frequency to equal a reference frequency set by the Fan-Speed Register, the prescaler, and the internal oscillator (see the Fan-Speed Register section). When the tachometer frequency is too high, the value of the DAC’s input register is increased by the regulator. Once the DAC voltage increases, the analog control loop forces the feedback voltage to rise, which reduces the voltage across the fan. Since fan speed is proportional to the voltage across the fan, the fan slows down. 2-Wire SMBus/I2C-Compatible Digital Interface From a software perspective, the MAX6650/MAX6651 appear as a set of byte-wide registers that contain speed control, tachometer count, alarm conditions, or configuration bits. These devices use a standard SMBus/I2C-compatible 2-wire serial interface to access the internal registers. 5 MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface VFAN = 5V OR 12V VCC 3V TO 5.5V VCC SMBus/I2C INTERFACE FAN SPEED SCL CONFIGURE SDA ALARM ENABLE SMBus/I2C INTERFACE ALARM STATUS TACH COUNT MAX6650 MAX6651 90kΩ TACH0 FAN 10kΩ TACHOMETER COUNT FB VOFFSET 90kΩ COUNT TIME GPIO DEF GPIO STATUS OUT CONTROL LOGIC 10kΩ DAC ADD ADDRESS DECODE 8-BIT DAC VREF 10kΩ GPIO0 ALERT GPIO1 FULL ON GPIO BLOCKS (FIGURE 5) GND Figure 1. Block Diagram The MAX6650/MAX6651 employ three standard SMBus protocols: write byte, read byte, and receive byte (Figure 2). The shorter protocol (receive) allows quicker transfers, provided that the correct data register was previously selected by a write or read byte instruction. Use caution with the shorter protocol in multimaster systems, since a second master could overwrite the command byte without informing the first master. Slave Addresses The device address can be set to one of four different values. Accomplish this by pin-strapping ADD so that more than one MAX6650/MAX6651 can reside on the same bus without address conflicts (Table 1). 6 Table 1. Slave Address Decoding (ADD) ADDRESS ADD HEX BINARY GND 90 1001 000 VCC 96 1001 011 No connection (high-Z) 36 0011 011 10kΩ resistor to GND 3E 0011 111 Maxim Integrated MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface S ADDRESS WR 7 bits 0 ACK COMMAND ACK DATA 8 bits Slave Address ACK P 8 bits Command byte: Selects which register you are writing to. Data byte: Data goes into the register set by the command byte (to set thresholds, configuration masks, and sampling rate). Figure 2a. SMBus Protocol: Write Byte Format S ADDRESS WR 7 bits 0 ACK ACK 8 bits Slave Address S COMMAND Command byte: Selects which register you are reading from. ADDRESS RD 7 bits 1 ACK DATA A P A P 8 bits Slave Address. Repeated due to change in data-flow direction Data byte: Reads from the register set by the command byte. Figure 2b. SMBus Protocol: Read Byte Format S ADDRESS RD 7 bits 1 ACK Slave Address DATA 8 bits Data byte: Reads data from the register commanded by the last read-byte or write-byte transmission; also used for SMBus alert response return address. Figure 2c. SMBus Protocol: Receive Byte Format S = Start condition P = Stop condition Maxim Integrated Shaded = Slave transmission ACK = Acknowledged = 0 A = Not acknowledged = 1 WR = Write = 0 RD = Read =1 7 MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface A tLOW B tHIGH C E D F G I H J K L M SMBCLK SMBDATA tHD:STA tSU:STA tSU:DAT A = START CONDITION B = MSB OF ADDRESS CLOCKED INTO SLAVE C = LSB OF ADDRESS CLOCKED INTO SLAVE D = R/W BIT CLOCKED INTO SLAVE E = SLAVE PULLS SMBDATA LINE LOW tHD:DAT tSU:STO tBUF J = ACKNOWLEDGE CLOCKED INTO MASTER K = ACKNOWLEDGE CLOCK PULSE L = STOP CONDITION, DATA EXECUTED BY SLAVE M = NEW START CONDITION F = ACKNOWLEDGE BIT CLOCKED INTO MASTER G = MSB OF DATA CLOCKED INTO SLAVE H = LSB OF DATA CLOCKED INTO SLAVE I = SLAVE PULLS SMBDATA LINE LOW Figure 3. SMBus Write Timing Diagram A B tLOW C D E F G tHIGH H J I K SMBCLK SMBDATA tSU:STA tHD:STA tSU:STO tSU:DAT A = START CONDITION B = MSB OF ADDRESS CLOCKED INTO SLAVE C = LSB OF ADDRESS CLOCKED INTO SLAVE D = R/W BIT CLOCKED INTO SLAVE E = SLAVE PULLS SMBDATA LINE LOW F = ACKNOWLEDGE BIT CLOCKED INTO MASTER G = MSB OF DATA CLOCKED INTO MASTER H = LSB OF DATA CLOCKED INTO MASTER tBUF I = ACKNOWLEDGE CLOCK PULSE J = STOP CONDITION K = NEW START CONDITION Figure 4. SMBus Read Timing Diagram Command-Byte Functions The 8-bit Command-Byte Register (Table 2) is the master index that points to the various other registers within MAX6650/MAX6651. The register’s power-on reset (POR) state is 0000 0000, so that a receive-byte transmission (a protocol that lacks the command byte) occurring immediately after POR returns the current speed setting. Fan-Speed Register In closed-loop mode, the MAX6650/MAX6651 use the Fan-Speed Register to set the period of the tachometer signal that controls the fan speed. The Fan-Speed Register is ignored in all other modes of operation. The MAX6650/MAX6651 regulate the fan speed by forcing the tachometer period (tTACH) equal to the scaled register value. One revolution of the fan generates two 8 tachometer pulses, so the required Fan-Speed Register value (KTACH) may be calculated as: tTACH = 1 / (2 x Fan Speed) KTACH = [tTACH x KSCALE x (fCLK / 128)] - 1 where the fan speed is in rotations per second (RPS), tTACH is the period of the tachometer signal, fCLK is the internal oscillator frequency (254kHz ±10%), and KSCALE is the prescaler value (see Configuration-Byte Register). Since the fan speed is inversely proportional to the tachometer period, the Fan-Speed Register value (KTACH) does not linearly control the fan speed (Table 3). Select the prescaler value so the fan’s full speed is achieved with a register value of approximately 64 (0100 0000) to optimize speed range and resolution. The MAX6651 may be controlled by an external oscilla- Maxim Integrated MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface Table 2. Command-Byte Assignments REGISTER COMMAND READ WRITE POR (DEFAULT) STATE FUNCTION SPEED 0000 0000 x x 00h Fan speed CONFIG 0000 0010 x x 0Ah Configuration GPIO DEF 0000 0100 x x FFh GPIO definition DAC 0000 0110 x x 00h DAC ALARM ENABLE 0000 1000 x x 00h Alarm enable ALARM 0000 1010 x — 00h Alarm status TACH0 0000 1100 x — 00h Tachometer 0 count TACH1 0000 1110 x — 00h Tachometer 1 count TACH2 0001 0000 x — 00h Tachometer 2 count TACH3 0001 0010 x — 00h Tachometer 3 count GPIO STAT 0001 0100 x — 1Fh GPIO status COUNT 0001 0110 x x 02h Tachometer count time Table 3. Fan Speed tTACH FAN SPEED (RPS) KSCALE (ms) KTACH FAN SPEED (RPM) KSCALE KSCALE 1 4 16 1 4 16 1 4 16 0000 0000 1.0 * * 500 * * 30,000 * * 0000 0001 1.0 * * 500 * * 30,000 * * 0000 0010 1.5 * * 330 * * 20,000 * * — — — — — — — — — — 0001 1110 16 3.9 * 32 128 * 1900 7700 * 0001 1111 16 4.0 1.0 31 124 500 1900 7400 30,000 0010 0000 17 4.2 1.0 30 120 480 1800 7200 29,000 — — — — — — — — — — 0100 0000 33 8.2 2.1 15.3 61.1 240 910 3700 15,000 — — — — — — — — — — 1111 1000 125 31 7.8 4 15.9 64 240 960 3830 *The minimum allowed tachometer period is 1ms. tor that overrides the internal oscillator (see GeneralPurpose Input/Output). When using an external oscillator (fOSC), calculate the Fan-Speed Register value with fCLK equal to f OSC . Codes above F8h (1111 1000) are allowed, but will not significantly decrease the frequency. Configuration-Byte Register The Configuration-Byte Register (Table 4) adjusts the prescaler, changes the tachometer threshold voltage, and sets the mode of operation. The three least-significant bits configure the prescaler division used to scale the tachometer period. Select the prescaler value so the Maxim Integrated fan’s full speed is achieved with a register value of approximately 64 (0100 0000) to optimize speed range and resolution (see the Fan Speed Register section). The fourth bit selects the fan operating voltage. The fifth and sixth bits configure the operating mode. The MAX6650/MAX6651 have four modes of operation: full-on, full-off (shutdown), closed-loop, and open-loop. In closed-loop operation, the external microcontroller (µC) sets the desired speed by writing an 8-bit word to the Fan-Speed Register (see the Fan-Speed Register section). The MAX6650/MAX6651 monitor the fan’s tachometer output and automatically adjust the voltage 9 MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface Table 4. Configuration Byte Register BIT NAME POR (DEFAULT) STATE 7 (MSB) to 6 — 0 Always 0 FUNCTION 5 to 4 MODE 00 Operating Mode: 00 = Software full-on (default) 01 = Software off (shutdown) 10 = Closed-loop operation 11 = Open-loop operation 3 5/12V 1 Fan/Tachometer Voltage: 0 = 5V 1 = 12V (default) 2 to 0 (LSB) SCALE 010 Prescaler Division: 000 = Divide by 1 001 = Divide by 2 010 = Divide by 4 (default) 011 = Divide by 8 100 = Divide by 16 General-Purpose Input/Output VCC MAX6650 MAX6651 VCC 3.0V TO 5.5V CBYPASS 100kΩ GPIO STATUS REGISTER GPIO DEFINITION REGISTER GPIO_ GND Figure 5. General-Purpose Input/Output Structure across the fan until the desired speed is reached. Openloop operation allows the µC to regulate fan speed directly. The µC reads the fan speed from the Tachometer-Count Register. Based on the tachometer count, the µC decides if the fan speed requires adjustment, and changes the voltage across the fan by writing an 8-bit word to the DAC Register. Full-on mode applies the maximum voltage across the fan, forcing it to spin at full speed. Configuring GPIO1 (see the General-Purpose Input/Output section) as an active-low input provides additional hardware control that fully turns on the fan and overrides all software commands. 10 The GPIO pins connect to the drain of the internal Nchannel MOSFET and pullup resistor (Figure 5). When the N-channel MOSFET is off (Table 5), the pullup resistor provides a logic-level high output. However, with the MOSFET off, the GPIO may serve as an input pin and its state is read from the GPIO Status Register (Table 6). The MAX6650/MAX6651 power up with the MOSFET off, so input signals may be safely connected to the GPIO pins. When using the GPIO pin as a general-purpose output, change the output by writing to the GPIO Definition Register. GPIO0 may be configured as an ALERT output that will go low whenever a fault-condition is detected (see the Alarm-Enable and Status Registers section). GPIO1 may be configured as a FULL ON input to allow hardware control to fully turn on the fan in case of software or µC failure. GPIO2 (MAX6651 only) may be configured as an internal clock output or as an external clock input to allow synchronization of multiple devices. Alarm-Enable and Status Registers The alarms are enabled only when the appropriate bits of the Alarm-Enable Register are set (Table 7). The maximum and minimum output level alarms function only when the device is configured to operate in the closedloop mode (see the Configuration-Byte Register section). The Alarm Status Register allows the system to determine which alarm caused the alert output (Table 8). The set-alarm and alert outputs clear after reading the Maxim Integrated MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface Table 5. GPIO Definition Register BIT POR (DEFAULT) STATE MAX6650 PIN MAX6651 PIN 7 1 N/A (must be 1) GPIO4 6 1 5:4 11 3:2 11 1:0 11 N/A (must be 1) N/A (must be 11) GPIO1 GPIO0 STATE 0 GPIO3 GPIO2 GPIO1 GPIO0 NAME POR (DEFAULT STATE) 7 (MSB) to 5 Always 0 0 4 GPIO4 (MAX6651 only) 1 3 GPIO3 (MAX6651 only) 1 2 GPIO2 (MAX6651 only) 1 1 GPIO1 1 0 (LSB) GPIO0 1 GPIO4 outputs a logic-high level or serves as an input. 0 GPIO3 outputs a logic-low level. 1 GPIO3 outputs a logic-high level or serves as an input. 00 GPIO2 serves as an external clock input. 01 GPIO2 serves as an internal clock output. 10 GPIO2 outputs a logic-low level. 11 GPIO2 outputs a logic-high level or serves as an input. 00 GPIO1 outputs a logic-high level or serves as an input. 01 GPIO1 serves as a FULL ON input. 10 GPIO1 outputs a logic-low level. 11 GPIO1 outputs a logic-high level or serves as an input. 00 GPIO0 outputs a logic-high level or serves as an input. 01 GPIO0 serves as an ALERT output. 10 GPIO0 outputs a logic-low level. 11 GPIO0 outputs a logic-high level or serves as an input. Alarm Status Register if the condition that caused the alarm is removed. Tachometer The Tachometer Count Registers record the number of pulses on the corresponding tachometer input during the period defined by the Tachometer Count-Time Register. Maxim Integrated GPIO4 outputs a logic-low level. 1 Table 6. GPIO Status Register BIT FUNCTION The MAX6651 contains three additional tachometer inputs, which may be used to monitor additional fans. For accurate control of multiple fans, use identical fans. The Tachometer Count-Time Register sets the integration time over which the MAX6650/MAX6651 count tachometer pulses. The devices can count up to 255 (FFh) pulses during the selected count time. If more than 255 pulses occur, the IC sets the overflow alarm and the Tachometer Count Register reports the maximum value of 255. Set the time register so the count register will not overflow under worst-case conditions (maximum fan speed) while maximizing resolution. Calculate the maximum measurable fan speed and minimum resolution with the following equations: Max Fan Speed (in RPS) = 255 / (2 x tCOUNT) Min Resolution (in RPS) = 1 / (2 x tCOUNT) where tCOUNT is the tachometer count time; 1kHz is the maximum allowable tachometer input frequency for the MAX6650/MAX6651. 11 MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface Table 7. Alarm-Enable Register Bit Masks NAME POR (DEFAULT) STATE 7 (MSB) to 5 — 0 Always 0 4 GPIO2 (MAX6651 only) 0 GPIO2 Alarm Enable/Disable (MAX6651 only) 3 GPIO1 0 GPIO1 Alarm Enable/Disable 2 TACH 0 Tachometer Overflow Alarm Enable/Disable 1 MIN 0 Minimum Output Level Alarm Enable/Disable 0 (LSB) MAX 0 Maximum Output Level Alarm Enable/Disable BIT FUNCTION 1 = Enabled Table 8. Alarm Status Register Bit Assignments NAME POR (DEFAULT) STATE 7 (MSB) to 5 — 0 Always 0 4 GPIO2 (MAX6651 only) 0 GPIO2 Alarm. Set when GPIO2 is low (MAX6651 only). 3 GPIO1 0 GPIO1 Alarm. Set when GPIO1 is low. 2 TACH 0 Tachometer Overflow Alarm 1 MIN 0 Minimum Output Level Alarm 0 (LSB) MAX 0 Maximum Output Level Alarm BIT FUNCTION 1 = Alarm condition Table 9. Tachometer Count-Time Register (Assumes two pulses per revolution) REGISTER VALUE (KCOUNT) COUNT TIME (s) MAXIMUM FAN SPEED (RPS) MINIMUM RESOLUTION (Hz/COUNT) 0000 0000 0.25 512 2 0000 0001 0.5 256 1 0000 0010 1.0 128 0.5 0000 0011 2.0 64 0.25 The first 6 bits of the Tachometer Count-Time Register are always zero, and the last 2 bits set the count time (Table 9). The count time may be determined from the following equation: tCOUNT = 0.25s x 2KCOUNT where KCOUNT is the numerical value of the two 2LSBs. The 0.25 factor has a ±10% uncertainty. 12 Upon power-up, the Tachometer Count Registers reset to 00h and the Tachometer Count-Time Register sets a 1s integration time. Digital-to-Analog Converter When using the open-loop mode of operation, the DAC Register sets the voltage on the low side of the fan. An internal operational amplifier compares the feedback voltage (VFB) with the reference voltage set by the 8-bit DAC, and adjusts the output voltage (VOUT) until the two input voltages are equal. The voltage at the FB pin may be determined by the following equation: VFB = (10 x VREF x KDAC) / 256 and the voltage across the fan is: ⎛ 90k ⎞ ⎛ KDAC ⎞ VFAN – ⎜ V + 1⎟ ⎜ ⎟ ⎝ 10k ⎠ ⎝ 256 REF ⎠ where KDAC is the numerical value of the DAC Register and VREF = 1.5V. The minimum feedback voltage is limited by the voltage drop across the external MOSFET (RON x IFAN), and the maximum voltage is limited by the fan’s supply voltage (VFAN). For linear operaMaxim Integrated MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface VFAN 5V OR 12V VCC VCC 3V TO 5.5V 10kΩ MAX6650 SMBus/I2C INTERFACE ALERT FULL ON SCL TACH0 SDA FB GPIO0 OUT GPIO1 ADD FAN CCOMP 10μF GND Figure 6. Fan Control with a Bipolar Transistor tion, use DAC values between 08h and B0h (see Typical Operating Characteristics). When using the closed-loop mode of operation, the contents of the DAC Register are ignored. When writing to the DAC, wait at least 500µs before attempting to read back. Power-on Reset (POR) The MAX6650/MAX6651 have volatile memory. To prevent ambiguous power-supply conditions from corrupting the data in the memory and causing erratic behavior, a POR voltage detector monitors VCC and clears the memory if VCC falls below 1.6V. When power is first applied and VCC rises above 1.6V, the logic blocks begin operating (though reads and writes at VCC levels below 3V are not recommended). Power-up defaults include the following: • All alarms are disabled. • Prescale divider is set to 4. • Fan speed is set in full-on mode. See Table 2 for the default states of all registers. Applications Information MOSFET and Bipolar Transistor Selection The MAX6650/MAX6651 drive an external N-channel MOSFET that requires five important parameters for proper selection: gate-to-source conduction threshold, maximum gate-to-source voltage, drain-to-source Maxim Integrated breakdown voltage, current rating, and drain-to-source on-resistance (RDS(ON)). Gate-to-source conduction threshold must be compatible with available VCC. The maximum gate-to-source voltage and the drain-tosource breakdown voltage rating should both be at least a few volts higher than the fan supply voltage (VFAN). Choose a MOSFET with a maximum continuous drain current rating higher than the maximum fan current. RDS(ON) should be as low as practical to maximize the feedback voltage range. Maximum power dissipation in the power transistor can be approximated by P = (VFAN X IFAN(MAX)) / 4. Bipolar power transistors are practical for driving small and midsize fans (Figure 6). Very-high-current fans may require output transistor base current greater than the MAX6650’s 50mA drive capability. Bipolar Darlington transistors will work but have poor saturation characteristics and could lose up to 2V to 3V of drive voltage. Resistor Selection The tachometer input voltages (VTACH_) and feedback voltage (V FB ) cannot exceed 13.2V (see Absolute Maximum Ratings). When using a fan powered by a 13.2V or greater supply (VFAN), protect these inputs from overvoltage conditions with series resistors. The resistance required to protect these pins may be calculated from the following equation: RPROTECT = [(VFAN(MAX) - 13.2V) x RIN] / 13.2V where VFAN(MAX) is the worst-case maximum supply voltage used to power the fan and RIN is the input 13 MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface Fan Selection impedance of the tachometer input (150kΩ max) or the feedback input (150kΩ max). For closed-loop operation and fan monitoring, the MAX6650/MAX6651 require fans with tachometer outputs. A tachometer output is typically specified as an option on many fan models from a variety of manufacturers. Verify the nature of the tachometer output (open collector, totempole) and the resultant levels, and configure the connection to the MAX6650/MAX6651 accordingly. Note how many pulses per revolution are generated by the tachometer output (this varies from model to model and among manufacturers, though two pulses per revolution is the most common). Table 10 lists the representative fan manufacturers and the models they make available with tachometer outputs. Compensation Capacitor A compensation capacitor is needed from the fan’s low side to ground to stabilize the analog control loop. Typically, this capacitor should be 10µF, but depending on the type of fan being used, a value between 1µF and 100µF may be required. The proper value has been selected when no ringing is present on the voltage at the fan’s low side. Table 10. Fan Manufacturers MANUFACTURER Low-Speed Operation FAN MODEL OPTION Comair Rotron All DC brushless models can be ordered with optional tachometer output. EBM-Papst Tachometer output optional on some models. NMB All DC brushless models can be ordered with optional tachometer output. Panasonic Panaflo and flat unidirectional miniature fans can be ordered with tachometer output. Sunon Tachometer output optional on some models. Brushless DC fans increase reliability by replacing mechanical commutation with electronic commutation. By lowering the voltage across the fan to reduce its speed, the MAX6650/MAX6651 are also lowering the supply voltage for the electronic commutation and tachometer electronics. If the voltage supplied to the fan is lowered too far, the internal electronics may no longer function properly. Some of the following symptoms are possible: • The fan may stop spinning. • The tachometer output may stop generating a signal. • The tachometer output may generate more than two pulses per revolution. The problems that occur, and the supply voltages at which they occur, depend on which fan is used. As a VFAN 5V OR 12V 10kΩ VCC VCC 3V TO 5.5V FAN 0 TACH0 10kΩ MAX6651 SCL SMBus/I2C INTERFACE SDA FAN 1 TACH1 10kΩ FAN 2 TACH2 FB ALERT FULL ON GPIO0 OUT GPIO1 ADD CCOMP GND Figure 7. Using the MAX6651 to Control Parallel Fans 14 Maxim Integrated MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface VCC 3V OR 5.5V TACH0 MAX6651 TACH1 FAN TACH 1 FAN TACH 2 TACH2 FAN TACH 3 TACH3 TO FAN VOLTAGE 5V OR 12V COM MAX4051 NO0 FAN TACH 4 NO1 FAN TACH 5 NO2 FAN TACH 6 GPIO2 ADDA NO3 FAN TACH 7 GPIO3 ADDB NO4 FAN TACH 8 GPIO4 ADDC NO5 FAN TACH 9 INH NO6 FAN TACH 10 NO7 V- FAN TACH 11 GND Figure 8. Monitoring Multiple Fans very rough rule of thumb, 12V fans can be expected to experience problems somewhere around 1/4 to 1/2 their rated speed. Predicting Future Fan Failure In systems that require maximum reliability, such as servers and network equipment, it can be advantageous to predict fan failure before it actually happens, to alert the system operator before the fan fails, minimizing down time. The MAX6650 allows the user to monitor the fan’s condition through the following modes. Full-On Mode By occasionally (over a period of days or weeks) turning the fan on full and measuring the resultant speed, a failing fan can be detected by a trend of decreasing speeds at a given power-supply voltage. Power-up is a convenient time to measure the maximum fan speed. Open-Loop Mode The fan’s condition can also be monitored using openloop mode. By characterizing the fan while it is new, fan failure can be determined by writing a predetermined value to the DAC and measuring the resultant fan speed. A decrease over time of the resultant speed may be an indication of future fan failure. Maxim Integrated Closed-Loop Mode The MAX6650 allows the system to read the DAC value used to regulate the fan speed. For a given speed, a significant change in the required DAC value may indicate future fan problems. Monitoring More than 4 Fans Use the MAX6651 to monitor up to four fans at a time (Figure 7). For systems requiring more than four fans, Figure 8 shows an application using an analog multiplexer (mux) to monitor 11 fans. GPIO2, GPIO3, and GPIO4 are connected to the mux’s address pins. By writing the appropriate value to the GPIO pins, the desired tachometer gets selected and counted by the TACH3 input. Because the TACH inputs are doublebuffered, and only sampled every other time slot, it is important to wait at least 4 times the tachometer count time before reading the register after changing the mux address. In the extreme case, a total of 25 fans can be monitored using three multiplexers connected to TACH1, TACH2, and TACH3. Do not connect TACH0 to a mux if the MAX6651 is under closed-loop mode. N + 1 Fan Application As shown in Figure 9, if any MAX6650 cannot maintain speed regulation, all other fans will automatically be turned on full. This can be useful in high-reliability systems where any single fan failure should not cause 15 MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface TO INT PIN ON NC ALERT GPIO0 MAX6650 FULL ON ALERT GPIO1 GPIO0 MAX6650 FULL ON ALERT ALERT GPIO0 FAN 3 GPIO1 GPIO0 MAX6650 FULL ON FAN 2 GPIO1 MAX6650 FULL ON FAN 1 FAN 4 GPIO1 Figure 9. N + 1 Application downtime. The system should be designed so that the number of fans used is one more than are actually needed. This way, there is sufficient cooling even if a fan fails. With all fans operating correctly, it is unnecessary to run the fans at their maximum speed. Reducing fan speed can reduce noise and increase the life of the fans. However, once a fan fails, it is important that the remaining fans spin at their maximum speed. In Figure 9, all the GPIO0s are configured as ALERT outputs, and all the GPIO1s are configured as FULL ON inputs. If any MAX6650 generates an ALERT (indicating failure), the remaining MAX6650s will automatically turn their fans on full. Temperature Monitoring and Fan Control The circuit shown in Figure 10 provides complete temperature monitoring and fan control. The MAX1617A (a remote/local temperature serial interface with SMBus) monitors temperature with a diode-connected transistor. Based on the temperature readings provided by the MAX1617A, the µC can adjust the fan speed proportionally with temperature. Connecting the ALERT output of the MAX1617A to the FULL ON input of the MAX6650/MAX6651 (see the General-Purpose Input/ Output section) allows the fan to turn on fully if the MAX1617A detects an overtemperature condition. MAX6501 Hardware Fail-Safe Figure 11 shows an application using a MAX6501 as a hardware fail-safe. The MAX6650 has its GPIO1 config- 16 ured as FULL ON input. The MAX6501 TOVER pin goes low whenever its temperature goes above a preset value. This pulls the FULL ON pin (GPIO1) low, forcing the fan to spin at its maximum speed. Figure 12 shows the use of multiple MAX6501s. The MAX6501 has an open-drain output, allowing multiple devices to be wire ORed to the FULL ON input. This configuration allows fail-safe monitoring of multiple locations around the system. Hot-Swap Application Hot swapping of a fan can be detected using the circuit in Figure 13 where GPIO2 is configured to generate an alert whenever it is pulled low. As long as the fan card is connected, GPIO2 is high. However, when the fan card is removed, a 2.2kΩ resistor pulls GPIO2 low, causing an interrupt. This signals to the system that a hot swap is occurring. Step-by-Step Part Selection and Software Setup Determining the Fan System Topology The MAX6650/MAX6651 support three fan system topologies. These are single fan control, parallel fan control, and synchronized fan control. Single Fan Control The simplest configuration is a single MAX6650 for each fan. If two or more fans are required per system, then additional MAX6650 controllers are used (one per fan). The advantage of this configuration is the ability to Maxim Integrated MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface GND ADD1 ADD0 MAX1617A TEMPERATURE SENSOR STBY DXP VCC DXN SCL INTERRUPT TO μC ALERT SDA VCC GPIO0 GPIO1 ALERT FULL ON VCC VFAN = 5V OR 12V MAX6650 MAX6651 μC SCL SCL TACH0 SDA SDA FB GND VCC OUT FAN ADD GND Figure 10. Temperature Monitoring and Fan Control Maxim Integrated 17 MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface VFAN 5V OR 12V VCC VCC 3V TO 5.5V 10kΩ MAX6650 SMBus/I2C INTERFACE ALERT SCL TACH0 SDA FB FAN GPIO0 CCOMP 10μF OUT MAX6501 FULL ON TOVER GPIO1 ADD GND Figure 11. MAX6501 Hardware Fail-Safe VFAN 5V OR 12V VCC VCC 3V TO 5.5V 10kΩ MAX6650 SMBus/I2C INTERFACE ALERT SCL TACH0 SDA FB FAN GPIO0 MAX6501 OUT TOVER FULL ON MAX6501 TOVER GPIO1 CCOMP 10μF ADD GND MAX6501 TOVER Figure 12. MAX6501 Hardware Fail-Safe independently control each fan. The disadvantage is cost, size, and complexity. For single fan control, use the MAX6650 (unless additional GPIOs are needed). Parallel Fan Control If multiple fans are required but independent control is not, then a single MAX6650/MAX6651 connected to two or more fans in parallel may make sense (Figure 7). The obvious advantage is simplicity, size, and cost 18 savings. If all the fans connected in parallel are the same type, they will tend to run at similar speeds. However, if one or more of the fans are wearing out, speed mismatches can occur. The MAX6651 allows the system to monitor up to four fans, ensuring any significant speed mismatches can be detected. For parallel fan control while monitoring up to four fan speeds, select the MAX6651. Maxim Integrated MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface VFAN 5V OR 12V HOT-SWAP SECTION VCC VCC 3V TO 5.5V 10kΩ MAX6651 SMBus/I2C INTERFACE ALERT SCL TACH0 SDA FB FAN GPIO0 CCOMP 10μF OUT FULL ON GPIO1 ADD GND VID GPIO2 2.2kΩ Figure 13. Hot-Swap Application For parallel fan control while monitoring only a single fan, select the MAX6650. Synchronized Fan Control (MAX6651 Only) In systems with multiple fans, an audible beat frequency can sometimes be detected due to fan speed mismatch. This happens in systems where fans are connected in parallel or in systems with a MAX6650 controlling each fan. In parallel fan systems, speed mismatches occur because no two fans are identical. Slight mechanical variations or loading differences can result in enough of a speed mismatch to cause an audible beat. Even in systems where there is a MAX6650/MAX6651 for each fan, there can still be speed mismatches. This is primarily due to the oscillator tolerance. The MAX6650/MAX6651 oscillator tolerance is specified to be ±10%. In the worst case, this could result in a 20% (one 10% high, one 10% low) speed mismatch. The solution is to use a single MAX6651 for each fan, and configure the parts to use a shared clock. The shared clock can either be an external system clock or one of the MAX6651’s internal clocks. If an external clock is used, its frequency can range from approximately 50kHz to 500kHz. Maxim Integrated For synchronized fan control, select the MAX6651. Combination In more complex systems, a combination of some or all of the above control types may be needed. Choosing a Fan Once the topology is chosen, the next step is to choose a fan. See the appropriate section. Enter a zero in bit 3 of the configuration register for a 5V fan and 1 for a 12V fan. Configuring this bit also adjusts the tachometer input threshold voltage. This optimizes operation of the MAX6650/MAX6651 for the operating voltage of the fan being used. Setting the Mode of Operation The MAX6650/MAX6651 have four modes of operation as determined by bits 5 and 6 of the configuration register: full on, full off, open loop, and closed loop. Full-On The full-on mode applies the maximum available voltage across the fan, guaranteeing maximum cooling. Full-on mode can be entered through software or hard- 19 MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface ware control. To enter full-on mode through hardware, see the Setting Up the GPIOs section. Note that a hardware full-on overrides all other modes. Below is a possible strategy for controlling the fan under open-loop mode: Configure the MAX6650/MAX6651 to run in software full-on mode by entering 00 into bits 5 and 4 of the configuration register. 1) On power-up, put the device in open-loop mode with a DAC value of 00 (full speed). 2) Allow the fan speed to settle. 3) Read the TACH register to determine the speed. Full-Off The full-off mode removes all the voltage across the fan, causing the fan to stop. Because the MAX6650/ MAX6651 work by controlling the voltage on the low side of the fan, either 5V or 12V will be on both leads. Enter full-off mode by entering 01 into bits 5 and 4 of the configuration register. 4) Gradually increase the DAC register value (in steps of 1 or 2) until the desired speed is obtained. In open-loop mode, any one of the four tachometer registers (MAX6651) can be used to measure and regulate the fan’s speed. This is especially useful in parallel fan systems where up to four fans will be controlled as one unit. Open Loop In open-loop mode, the MAX6650/MAX6651 do not actually regulate the fan speed. Speed regulation requires an external µC. Although open-loop mode allows maximum flexibility, it also requires the most software/processor overhead. In open-loop mode, the MAX6650/MAX6651 act as an SMB/I2C-controlled voltage regulator. The µC adjusts the voltage across the fan by writing an 8-bit value to the DAC register. This gives the µC direct control of the voltage across the fan. Speed regulation is accomplished by periodically reading the tachometer register(s) and adjusting the DAC register appropriately. The DAC value controls the voltage across the fan according to the following equation: VFAN = VFAN_SUPPLY - [((R2) / R1) + 1] x VREF x KDAC / 256 where VFAN = the voltage across the fan, VFAN_SUPPLY = the supply voltage for the fan (5V or 12V), R2 = 90kΩ (typ), R1 = 10kΩ (typ), VREF = 1.5V (typ), and KDAC = the value in the DAC register. Note several important things in this equation. First, the voltage across the fan moves in the opposite direction of the DAC value. In other words, low DAC values correspond to higher voltages across the fan and therefore higher speeds. Second, DAC values greater than 180 will result in 0V across a 12V fan. Similarly, DAC values greater than 76 will produce 0V across a 5V fan. This limits the useful range of the DAC from 0 to 180 for 12V fans and 0 to 76 for 5V fans. Remember that device tolerances can cause the output voltage value to vary significantly from unit to unit and over temperature. However, because this voltage is within a closed speed-control loop, such errors are corrected by the loop. Care must be taken with this mode to prevent instability, which can be caused by trying to update the fan speed too often or in increments that are too large. Instability can result in the fan speeding up and slowing down repeatedly. Determining the proper update rate, as shown in the following steps, depends largely on the fan’s mechanical time constant and the system’s loop gain (DAC step sizes): 1) Enter open-loop mode by setting bits 5 and 4 of the control register to 11. 2) Determine the speed of the fan(s) by reading the TACH register(s). 3) Increase or decrease the DAC register to decrease or increase the voltage across the fan, thereby adjusting its speed. Closed Loop In closed-loop mode, the SMBus/I2C master (usually a µC) writes a desired fan speed to the MAX6650/ MAX6651, and the device automatically adjusts the voltage across the fan to maintain this speed. This operation mode requires less software/processor overhead than the open-loop mode. Once the desired speed has been written, the MAX6650/MAX6651 control the fan’s speed independently, with no intervention required from the master. If desired, the MAX6650/ MAX6651 can be configured to generate an interrupt if it is unable to regulate the fan’s speed at the desired value (see Setting Up Alarms). The MAX6650/MAX6651 can regulate only the speed of the fan connected to the TACH0 input. Fans connected in parallel to the TACH0 fan will tend to run at similar speeds (assuming similar fans). When going from full-off to closed-loop-mode, it is recommended following this sequence: 1) Full-off mode 2) Full-on mode (with sufficient pause to initiate movement) 3) Closed-loop mode 20 Maxim Integrated MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface The MAX6650 regulates fan speed in the following manner. The output of an internal 254kHz oscillator is divided by 128, generating a roughly 2kHz signal. This signal is divided by 1 plus the value in the speed register and is used as a reference frequency. For example, 02h in the speed register will result in a 667Hz [2kHz / (02h+1)] reference frequency, which is then compared against the frequency at the tachometer input divided by the prescaler value. The MAX6650/MAX6651 attempt to keep the tachometer frequency divided by the prescaler equal to the reference frequency by adjusting the voltage across the fan. If the tachometer frequency divided by the prescaler value is less than the reference frequency, the voltage across the fan is increased. Remember that the tachometer will give two pulses per revolution of the fan. The following equations describe the operation. When in regulation: [fCLK / (128 x (KTACH + 1))] = 2 x FanSpeed / KSCALE where fCLK = oscillator frequency (either the 254kHz internal oscillator or the externally applied clock), KTACH = the value in the speed register, FanSpeed = the speed of the fan in revolutions per second (Hz), KSCALE = the prescaler value (1, 2, 4, 8, or 16). Solving for all four variables: KTACH = [(fCLK x KSCALE) / (256 x FanSpeed)] - 1 KSCALE = [256 x FanSpeed x (KTACH + 1)] / fCLK FanSpeed = KSCALE x fCLK / [256 x (KTACH + 1)] fCLK = 256 x FanSpeed x (KTACH + 1) / KSCALE If the internal oscillator is used, setting fCLK to 254kHz can further reduce the equations: Equation 1: KSCALE = FanSpeed x (KTACH + 1) / 992 Equation 2: KTACH = (992 x KSCALE / FanSpeed) - 1 Equation 3: FanSpeed = 992 x KSCALE / (KTACH + 1) Enter closed-loop mode by entering 10 into bits 5 and 4 of the configuration register. Note that in equation 3, the fan speed is inversely proportional to (KTACH + 1). This means the regulated fan speed is a nonlinear function of the value written to the speed register. Low values written to the speed register can result in large relative changes in fan speed. For best results, design the system so that small values (such as 02h) are not needed. This is easily accomplished because an 8-bit speed register is used, and fan-speed control should rarely need more than 16 speeds. A good compromise is to design the system (by selecting the appropriate prescaler value) so that the maximum-rated speed of the fan occurs when the Maxim Integrated speed register equals approximately 64 (decimal). Although 64 is a good target value, values between 20 and 100 will work fine. The prescaler value also affects the response time and the stability of the speed-control loop. Adjusting the prescaler value effectively adjusts the loop gain. A larger prescaler value will slow the response time and increase stability, while a smaller prescaler value will yield quicker response time. The optimum prescaler value for response time and stability depends on the fan’s mechanical time constant. Small, fast-spinning fans will tend to have small mechanical time constants and can benefit from smaller prescaler values. A good rule of thumb is to try the selected prescaler value in the target system. Set K TACH to around 75% of full scale, and watch for overshoot or oscillation in the fan speed. Also look for overshoot or oscillation when KTACH is changed from one value to another (e.g., from 75% of full-scale speed to 90% of full scale). If there is unacceptable overshoot or if the fan speeds up and slows down with K TACH , set it to a constant value; increase the prescaler value. Enter the appropriate prescaler value in bits zero to 2 of the configuration register. Fan speed is a trade-off between cooling requirements, noise, power, and fan wear. In general, it is desirable (within limits) to run the fan at the slowest speed that will accomplish the cooling goals. This will reduce power consumption, increase fan life, and minimize noise. When calculating the desired fan speed, remember that the above equations are written in rotations per second (RPS), where most fans are specified in rotations per minute (RPM). Write the desired fan speed to the speed register. Example: Assume the following: • 12V fan is rated at 2000RPM at 12V. • Use the internal oscillator (fCLK = 254kHz). • Desired fan speed = 1500RPM (25RPS). First, calculate an appropriate prescaler value (KSCALE) using equation 1. Attempt to get KTACH as close to 64 as possible for the maximum speed of 2000RPM. • Set FanSpeed = 33.3RPS (2000RPM/60). • Set KTACH = 64. • Solving equation 1 gives KSCALE = 2.18. 21 MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface We will start with KSCALE = 2 (to increase stability, a 4 could be tried, or to improve response time, a 1 could be tried). Second, calculate the appropriate value for the Speed Register (KTACH) using equation 2. • Set FanSpeed = 25RPS (1500PRM/60). • Solving for equation 2 gives KTACH = 78 for KSCALE = 2, KTACH = 39 for KSCALE = 1, or KTACH = 158 for K = 4. Determining the Tachometer Count Time To monitor the fan speed using the SMBus/I2C, the next step is to determine the tachometer count time. In systems running in open-loop mode, this is necessary. In closed-loop or full-speed mode, reading the tachometer can serve as a valuable check to ensure the fan and the control loop are operating properly. The MAX6650/MAX6651 use an 8-bit counter to count the tachometer pulses. This means the device can count from 0 to 255 tachometer pulses before overflowing. The MAX6650/MAX6651 can accommodate a large range of fan speeds by allowing the counting interval to be programmed. Smaller/faster fans should use smaller count times. Although larger fans could also use smaller count times, resolution would suffer. Choose the slowest count time that will not overflow under worstcase conditions. Fans are mechanical devices, and their speeds are subject to large tolerance variations. If an overflow does occur, the counter will read 255. The MAX6650/MAX6651 can be configured to generate an alert if an overflow is encountered (see Setting Up Alarms). Note that the prescaler value has no effect on the TACH0 register. Enter the appropriate count-time value in the tachometer count-time register. Example: Assume a 12V fan rated at 2000 RPM. To accommodate large tolerance variations, choose a count time appropriate for a maximum speed of 3000RPM; 3000RPM is 50RPS and generates a 100Hz (2 pulses/revolution) tachometer signal. Table 9 indicates a count time of 2s will optimize resolution. With a 2s count time, speeds as fast as 3825RPM can be monitored without overflow. The minimum resolution will be 15RPM or 0.75% of the rated speed of 2000RPM. Setting Up the GPIOs To increase versatility, the MAX6650/MAX6651 have two and five general-purpose digital inputs/outputs, respectively. These GPIOs can be configured through the SMBus/I2C. 22 Digital Out Low All GPIOs can be configured to output a logic-level low. The MAX6650/MAX6651 are designed to sink up to 10mA. This high sink current can be especially useful for driving LEDs. On the MAX6651, for GPIO3 and GPIO4, write a zero to the appropriate location in the GPIO definition register. For GPIO0, GPIO1, and (MAX6551 only) GPIO2, write a 10 to the appropriate location in the GPIO definition register. Digital Out High All GPIOs can be configured to generate a logic-level high. An output high is generated using an open-drain output stage with an internal pullup resistor of nominally 100kΩ. The MAX6650/MAX6651 power-up default state is with all GPIOs configured as output highs. On the MAX6651, for GPIO3 and GPIO4, write a 1 to the appropriate location in the GPIO definition register. For GPIO0, GPIO1, and (MAX6551 only) GPIO2, write an 11 to the appropriate location in the GPIO definition register. Digital Input Since a logic-level high output is open drain with an internal pullup, an external device can actively pull this pin low. The MAX6650/MAX6651 allow the user to read the GPIO value through the GPIO status register. • Configure the GPIO as an output logic level high (see above). • Read the state of the GPIO by reading the GPIO status register. Alert Output GPIO0 can also serve as an ALERT output. The ALERT output is designed to drive an interrupt on a µC. The ALERT output goes low whenever an enabled alarm condition occurs (see Setting Up Alarms). Configure GPIO0 as an ALERT output by writing a 01 to bits 1 and 0 of the GPIO definition register. Full-On Input GPIO1 can also be configured as a full-on input. When the full-on pin is pulled low, the MAX6650/MAX6651 apply the full available voltage across the fan. This happens independently of the software mode of operation. This is a particularly valuable feature in high-reliability systems, designed to prevent software malfunctions from causing system overheating. Configure GPIO1 as a full-on input by writing a 01 to bits 3 and 2 of the GPIO definition register. Maxim Integrated MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface Synchronizing Fans GPIO2 can be configured to allow multiple MAX6651s to synchronize the speeds of the fans they are driving (Figure 14). Synchronization is accomplished by having one of the MAX6651s (or an external clock) serve as the clock master by configuring one of the GPIO2s in the system as a clock output. The remaining GPIO2s in the system need to be configured as clock inputs: • Electrically connect all MAX6651 GPIO2s together. • Configure one of the MAX6651’s GPIO2s to be a clock output, using the GPIO Definition Register (set bits 5 and 4 to 01). • Configure the rest of the GPIO2s as clock inputs, using the GPIO Definition Register (set bits 5 and 4 to 00). • Configure all MAX6651s in closed-loop mode. MAX6501 CLOCK OUT • Configure all prescaler values to be equal. • Write identical values to all speed registers. Setting Up Alarms The MAX6650/MAX6651 can be configured to generate an ALERT output on GPIO0 whenever certain events, such as control loop out of regulation, tachometer overflow, or GPI01/GPI02 being driven low, occur. This is designed to enhance the “set and forget” functionality of the fan control system. Configure GPIO0 to be an ALERT output (see above). Minimum/Maximum Output Level Alarm The minimum/maximum output level alarms are designed to warn the system when the MAX6650/ MAX6651 are unable to maintain speed regulation in closed-loop mode. The MAX6650/MAX6651 maintain speed regulation by adjusting the voltage across the fan. If the desired speed can’t be attained, one of these alarms will be generated. Possible causes for failure to attain the desired speed include system programming problems, incipient fan failure, and a programmed speed that the fan cannot support. The minimum output alarm occurs when the DAC output is 00h. A DAC value of 00h means that the MAX6650/MAX6651 have applied the largest available voltage across the fan. This typically means the fan is unable to spin as fast as the desired speed. The maximum output alarm occurs when the DAC value is FFh. A DAC value of FFh means the MAX6650/MAX6651 have tried to reduce the voltage across the fan to 0. Although this would seem to indicate the fan is spinning faster than the desired speed, this should rarely happen. If this alarm occurs, it probably indicates some type of system error. Maxim Integrated GPIO2 MAX6501 CLOCK IN FAN 2 GPIO2 MAX6501 CLOCK IN FAN 1 FAN 3 GPIO2 Figure 14. Synchronizing Fans Enable the minimum/maximum output level alarm by setting bits 0 and 1 of the alarm enable register to 11. Tachometer Overflow Alarm If any tachometer counter overflows (reaches a count of 255), this alarm will be set. Enable the overflow output level alarm by setting bit 2 of the alarm enable register bit to 1. GPIO1/2 Pulled Low Enabling this alarm causes the ALERT output to go low whenever GPIO1 or GPIO2 is pulled low. This will occur independent of the configuration of GPIO1 or GPIO2. Enable the GPIO1/GPIO2 output level alarms by setting bits 3 and/or 4 of the alarm enable register bit to 1. Clearing the ALERT Once an ALERT is generated, determine which alarm caused the ALERT pin to go low. Do this by reading the Alarm Status Register. An ALERT output will stay active (low) even if the condition that caused the alert is removed. Reading the Alarm Status Register clears the ALERT, if the condition that caused the alert is gone. If the condition has not gone away, the ALERT will stay active. Disabling the alarm with the Alarm Enable Register will cause the ALERToutput to go inactive. Read the Alarm Status Register. 23 MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface Pin Configurations TOP VIEW TACH0 1 GND 2 MAX6650 10 FB TACH0 1 16 TACH1 9 VCC TACH2 2 15 FB 8 OUT TACH3 3 14 VCC SDA 3 SCL 4 7 GPIO0 GND 4 ADD 5 6 GPIO1 SDA 5 12 GPIO3 SCL 6 11 GPIO2 GPIO4 7 10 GPIO0 μMAX MAX6651 ADD 8 13 OUT 9 GPIO1 QSOP Package Information For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. 24 PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. 10 µMAX U10-2 21-0061 90-0330 16 QSOP E16-1 21-0055 90-0167 Maxim Integrated MAX6650/MAX6651 Fan-Speed Regulators and Monitors with SMBus/I2C-Compatible Interface Revision History REVISION NUMBER REVISION DATE 4 7/10 5 12/12 DESCRIPTION PAGES CHANGED Added lead-free parts to the Ordering Information 1 Updated Table 5 to include the pins for both the MAX6650 and MAX6651 11 Updated the ADD parameters in the Electrical Characteristics table; updated the conditions notes for tHD:DAT, tR, and tF in the Timing Characteristics table; updated Table 1 3, 6 Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000 © 2012 Maxim Integrated Products, Inc. 25 Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.