MIC1555/1557

MIC1555/1557
IttyBitty® RC Timer/Oscillator
General Description
®
The MIC1555 IttyBitty CMOS RC timer/oscillator and
®
MIC1557 IttyBitty CMOS RC oscillator are designed to
provide rail-to-rail pulses for precise time delay or
frequency generation.
The devices are similar in function to the industry standard
“555”, without a frequency control (FC) pin or an opencollector discharge (D) pin. The threshold pin (THR) has
precedence over the trigger (TRG) input, ensuring that the
BiCMOS output is off when TRG is high.
The MIC1555 can be used as an astable (oscillator) or
monostable (one-shot) with separate threshold and trigger
inputs. In the one-shot mode, the output pulse width is
precisely controlled by an external resistor and a capacitor.
Time delays may be accurately controlled from microseconds to hours. In the oscillator mode, the output is
used to provide precise feedback, with a minimum of one
resistor and one capacitor producing a 50% duty cycle
square wave.
The MIC1557 is designed for astable (oscillator) operation
only, with a chip select/reset (CS) input for low power shutdown. One resistor and one capacitor provide a 50% duty
cycle square wave. Other duty-cycle ratios may be
produced using two diodes and two resistors.
The MIC1555/7 is powered from a +2.7V to +18V supply
voltage and is rated for –40°C to +85°C ambient
temperature range. The MIC1555/7 is available in SOT-235, and thin SOT23-5 5-pin packages. A low profile, ultrathin, (UTDFN), version of the MIC1555 (with chip select) is
also available.
Datasheets and support documentation are available on
Micrel’s website at: www.micrel.com.
Features
• +2.7V to +18V operation
• Low current
− <1µA typical shutdown mode (MIC1557)
− 200µA typical (TRG and THR low) at 3V supply
• Timing from microseconds to hours
• “Zero” leakage trigger and threshold inputs
• 50% square wave with one resistor, one capacitor
• Threshold input precedence over trigger input
• <15Ω output on resistance
• No output cross-conduction current spikes
• <0.005%/°C temperature stability
• <0.055%/V supply stability
• 10-pin ultra-thin DFN package (2mm × 2mm × 0.4mm)
• Small SOT-23-5 surface mount package
Applications
•
•
•
•
•
•
•
•
•
•
•
Precision timer
Pulse generation
Sequential timing
Time-delay generation
Missing pulse detector
Micropower oscillator to 5MHz
Charge-pump driver
LED blinker
Voltage converter
Linear sweep generator
Variable frequency and duty cycle oscillator
IttyBitty is a registered trademark of Micrel, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
August 12, 2015
Revision 6.1
Micrel, Inc.
MIC1555/1557
Typical Applications
Monostable (One-Shot)
Monostable (with Enable)
Astable (Oscillator)
August 12, 2015
2
Revision 6.1
Micrel, Inc.
MIC1555/1557
Ordering Information
Part Number
Top Marking
(1, 2)
Temperature Range
Package
Package Height (mm)
MIC1555YD5
T12
–40°C to +85°C
5-Pin Thin SOT-23
1.0 (maximum)
MIC1555YMU
T14
–40°C to +85°C
10-Pin 2mm × 2mm UTDFN
0.4 (maximum)
MIC1555YM5
T10
–40°C to +85°C
5-Pin SOT-23
0.9 – 1.45
MIC1557YD5
T13
–40°C to +85°C
5-Pin Thin SOT-23
1.0 (maximum)
MIC1557YM5
T11
–40°C to +85°C
5-Pin SOT-23
0.9 – 1.45
Note:
1. Underbars (
) shown for the top marking may not be to scale.
2. The top marking in the YMU package does not have an underbar.
Pin Configuration (MIC1555 SOT-23 and TSOT-23)
5-Pin SOT-23 (M5)
(Top View)
5-Pin TSOT-23 (D5)
(Top View)
Pin Description (MIC1555 SOT-23 and TSOT-23)
Pin Number
Pin Name
1
VS
2
GND
Ground: Supply return.
3
OUT
Output: CMOS totem-pole output.
4
TRG
Trigger (Input): Sets output high. Active low (at ≤2/3VS nominal).
5
THR
Threshold (Dominant Input): Sets output low. Active high (at ≥2/3VS nominal).
August 12, 2015
Pin Function
Supply (Input): +2.7V to +18V supply.
3
Revision 6.1
Micrel, Inc.
MIC1555/1557
Pin Configuration (MIC1555 UTDFN)
10-Pin UTDFN (MU)
(Top View)
Pin Description (MIC1555 UTDFN)
Pin Number
Pin Name
Pin Function
1
VS
Supply (Input): +2.7 to +18V supply.
2
CS
Chip Select/Reset (Input): Active high at >2/3VS. Output off when low at <1/3VS. If chip select
functionality is not desired, CS may be connected directly to VS.
3, 4, 7, 9
NC
No Connect. This pin is not internally connected.
5
THR
Threshold (Dominant Input): Sets output low. Active high (at ≥ 2/3VS nominal).
6
TRG
Trigger (Input): Sets output high. Active low (at ≤2/3VS nominal).
8
GND
Ground: Supply return.
10
OUT
Output: CMOS totem-pole output.
Pin Configuration (MIC1557 SOT-23 and TSOT-23)
5-Pin SOT-23 (M5)
(Top View)
5-Pin TSOT-23 (D5)
(Top View)
Pin Description (MIC1557 SOT-23 and TSOT-23)
Pin Number
Pin Name
1
T/T
2
GND
Pin Function
Trigger/Threshold (Input): Internally connected to both threshold and trigger functions. When the
voltage at this pin is ≤2/3VS it will set the output high. When the voltage at this pin is ≥2/3VS it will set
the output low.
Ground: Supply return.
CS
Chip Select/Reset (Input): Active high at >2/3VS. Output off when low at <1/3VS. If chip select
functionality is not desired, CS may be connected directly to VS.
4
VS
Supply (Input): +2.7 to +18V supply.
5
OUT
3
August 12, 2015
Output: CMOS totem-pole output.
4
Revision 6.1
Micrel, Inc.
MIC1555/1557
Absolute Maximum Ratings(3)
Operating Ratings(4)
Supply Voltage (VS) ...................................................... +22V
Threshold Voltage (VTHR, VT/T). .................................... +22V
Trigger Voltage (VTGR, VT/T) .......................................... +22V
Lead Temperature (soldering, 10s) ............................ 300°C
Ambient Storage Temperature .................. –65°C to +150°C
(5)
ESD HBM Rating ......................................................... 2kV
ESD MM Rating............................................................ 200V
Supply voltage (VS) ....................................... +2.7V to +18V
Ambient Temperature (TA) .......................... –40°C to +85°C
Package Thermal Resistance
SOT23-5 and Thin SOT23-5 (θJA) ................... 250°C/W
2mm × 2mm UTDFN (θJA) ................................. 90°C/W
Electrical Characteristics
TA = 25°C, bold values indicate –40°C ≤ TA ≤ +85°C, unless noted.
Parameter
Supply Current
Monostable Timing Accuracy
Condition
Min.
Typ.
Max.
VS = 5V
240
300
VS = 15V
350
400
2
RA = 10kΩ, C =0.1µF, VS = 5V
858
RA = 10kΩ, C =0.1µF, VS = 5V
VS = 5V, –55°C ≤ TA ≤ +125°C
(6)
Monostable Drift
Overtemperature
Monostable Drift over Supply
Astable Timing Accuracy
Maximum Astable
Frequency
%
1161
µs
VS = 10V, –55°C ≤ TA ≤ +125°C
150
VS = 15V, –55°C ≤ TA ≤ +125°C
200
(6)
0.5
%/V
2
%
(6)
VS = 5V to 15V
RA = RB = 10kΩ, C = 0.1µF, VS = 5V
RA = RB = 10kΩ, C = 0.1µF, VS = 5V
1717
ppm/°C
2323
5
RT = 1kΩ, CT = 47pF, VS = 8V
(6)
Astable Drift over Supply
µA
100
(6)
VS = 5V, –55°C ≤ TA ≤ +125°C
Astable Drift
Overtemperature
Units
µs
MHz
100
VS = 10V, –55°C ≤ TA ≤ +125°C
150
VS = 15V, –55°C ≤ TA ≤ +125°C
200
(6)
(6)
(6)
ppm/°C
0.5
VS = 5V to 15V
%/V
Threshold Voltage
VS = 15V
61
Trigger Voltage
VS = 15V
27
Trigger Current
VS = 15V
50
nA
Threshold Current
VS = 15V
50
nA
Chip Select
67
72
%/VS
32
37
%/VS
on > 2/3 VS
50
67
72
off < 1/3 VS
28
33
50
%/VS
Notes:
3. Exceeding the absolute maximum ratings may damage the device
4. The device is not guaranteed to function outside its operating ratings.
5. Devices are ESD protected, however handling precautions recommended.
6. Not tested.
August 12, 2015
5
Revision 6.1
Micrel, Inc.
MIC1555/1557
Electrical Characteristics (Continued)
TA = 25°C, bold values indicate –40°C ≤ TA ≤ +85°C, unless noted.
Parameter
Output Voltage Drop
Supply Voltage
Output Rise Time
Output Fall Time
August 12, 2015
Condition
Min.
Typ.
Max.
VS = 15V, ISINK = 20mA
0.3
1.25
VS = 5V, ISINK = 3.2mA
0.08
0.5
VS = 15V, ISOURCE = 20mA
14.1
14.7
VS = 5V, ISOURCE = 3.2mA
3.8
4.7
Functional Operation
(6)
2.7
18
Units
V
V
(6)
15
ns
(6)
15
ns
RL = 10MΩ, CL = 10pF, VS = 5V
RL = 10MΩ, CL = 10pF, VS = 5V
6
Revision 6.1
Micrel, Inc.
MIC1555/1557
Typical Characteristics
TA = 25°C, VIN = +5V.
August 12, 2015
7
Revision 6.1
Micrel, Inc.
MIC1555/1557
MIC1555 Functional Block Diagrams
MIC155YM5/MIC155YD5 Block Diagram with External Components (Monostable Configuration)
MIC1555YMU Block Diagram with External Components (Monostable Configuration)
August 12, 2015
8
Revision 6.1
Micrel, Inc.
MIC1555/1557
MIC1557 Functional Block Diagram
MIC1557YM5/MIC1557YD5 Block Diagram with External Components (Astable Configuration)
August 12, 2015
9
Revision 6.1
Micrel, Inc.
MIC1555/1557
Functional Description
Basic Monostable Operation
A momentary low signal applied to TRG causes the
output to go high. The external capacitor charges slowly
through the external resistor. When threshold voltage
(VTHR) reaches 2/3VS, the output is switched off,
discharging the capacitor. During power-on, a single
pulse may be generated.
The MIC1555/7 provides the logic for creating simple RC
timer or oscillator circuits.
The MIC1555 has separate THR (threshold) and TRG
(trigger) connections for monostable (one-shot) or astable
(oscillator) operation.
The MIC1557 has a single T/T (threshold and trigger)
connection for astable (oscillator) operation only. The
MIC1557 includes a CS (chip select/reset) control.
For more information, refer to the MIC1555 Functional
Block Diagrams.
For more information, refer to the MIC1555 Functional
Block Diagrams and MIC1557 Functional Block Diagram.
Basic Astable Operation
Refer to the MIC1557 functional diagram.
Supply
Voltage supply (VS) is rated for +2.7V to +18V. An
external capacitor is recommended to decouple noise.
The MIC1557 starts with T/T low, causing the output to
go high. The external capacitor charges slowly through
the external resistor. When VT/T reaches 2/3VS (threshold
voltage), the output is switched off, slowly discharging the
capacitor. When VT/T decreases to 1/3VS (trigger
voltage), the output is switched on, causing VT/T to rise
again, repeating the cycle.
Resistive Divider
The resistive voltage divider is constructed of three equal
value resistors to produce 1/3VS and 2/3VS voltage for
trigger and threshold reference voltages.
For more information, refer to the MIC1557 Functional
Block Diagram.
Chip Select/Reset (MIC1555YMU and MIC1557 only)
Chip select/reset (CS) controls the bias supply to the
oscillator’s internal circuitry. CS must be connected to
CMOS logic-high or logic-low levels. Floating CS will
result in unpredictable operation. When the chip is
deselected, the supply current is less than 1µA. Forcing
CS low resets the device by setting the flip flop, forcing
the output low. If Chip Select functionality is not desired,
CS may be connected directly to VS.
Threshold Comparator
The threshold comparator is connected to S (set) on the
RS flip-flop. When the threshold voltage (2/3VS) is
reached, the flip-flop is set, making the output low. THR
is dominant over TRG.
Trigger Comparator
The trigger comparator is connected to R (reset) on the
RS flip-flop. When TRG (trigger) goes below the trigger
voltage (1/3VS), the flip-flop resets, making the output
high.
Flip-Flop and Output
A reset signal causes Q to go low, turning on the Pchannel MOSFET and turning off the N-channel
MOSFET. This makes the output rise to nearly VS.
A set signal causes Q to go high, turning off the Pchannel MOSFET, and turning on the N-channel
MOSFET, grounding OUT.
August 12, 2015
10
Revision 6.1
Micrel, Inc.
MIC1555/1557
Application Information
Basic Monostable (One-Shot) Circuit
A monostable oscillator produces a single pulse each
time that it is triggered, and is often referred to as a “oneshot”. The pulse width is constant, while the time
between pulses depends on the trigger input. One-shots
are generally used to “stretch” incoming pulses, of
varying widths, to a fixed width. The IttyBitty MIC1555 is
designed for monostable operation, but may also be
connected to provide astable oscillations. The pulse width
is determined by the time it takes to charge a capacitor
from ground to a comparator trip point. If the capacitor
(CT) is charged through a resistor (RT) connected to the
output of an MIC1555, the trip point is approximately
1.1RTCT (the same time as the initial power-on cycle of
an astable circuit.) If the trigger pulse of an MIC1555
remains low longer than the output pulse width, short
oscillations may be seen in the output of a one-shot
circuit, since the threshold pin has precedence over the
trigger pin. These occur since the output goes low when
the threshold is exceeded, and then goes high again as
the trigger function is asserted. AC coupling the input with
a series capacitor and a pull-up resistor, with an RC time
constant less than the pulse width, will prevent these
short oscillations. A diode (DT) in parallel with (RT) resets
the one-shot quickly.
The period of a monostable circuit is:
t = k2 RC
where:
t = period (s)
k2 = Constant (see Typical Characteristics)
R = Resistance (Ω)
C = Capacitance (F)
Basic Astable (Oscillator) Circuits
An astable oscillator switches between two states, “on”
and “off”, producing a continuous square wave. The
IttyBitty MIC1557 is optimized for this function, with the
two comparator inputs, threshold and trigger (T/T), tied
together internally. CS is brought out to allow on-off
control of the oscillator.
The MIC1555 may also be used as an astable oscillator
by tying the threshold and trigger pins together, forming a
T/T pin. If a resistor (RT) is connected from the output to a
grounded timing capacitor (CT), the voltage at their
junction will ramp up from ground when the output goes
high. If the T/T pin is connected to this junction, the
output will switch low when the ramp exceeds 2/3 of the
input voltage. The junction's voltage ramps down toward
ground while the output is low. When the ramp is below
1/3 of the input voltage, the output switches to high, and
the junction ramps up again. The continuing frequency of
an MIC1555/7 astable oscillator depends on the RC time
constant, and is approximately 0.7/RC below 1MHz. At
frequencies above 1MHz the RC multiplier increases as
capacitance is decreased, and propagation delay
becomes dominant. Non-symmetrical oscillator operation
is possible at frequencies up to 5MHz.
If a duty cycle other than 50% is desired, a low-power
signal diode may be connected in series with the timing
resistor (RA), and a second resistor (RB) in series with an
opposite facing switching diode and resistor connected in
parallel (see Figure 2). The frequency is then made up of
two components, the charging time (tA) and the
discharging time (tB) tA = 0.7RACT and tB = 0.7RBCT. The
frequency is the reciprocal of the sum of the two times tA
+ tB, so the total time is 1.4RTCT. The first half-cycle of an
astable, after power-on or CS enable, is lengthened since
the capacitor is charging from ground instead of the 1/3
input trigger trip voltage, to 1.1RC, the same as a
monostable pulse.
Figure 1. One-Shot Diagram
August 12, 2015
11
Revision 6.1
Micrel, Inc.
MIC1555/1557
The MIC1555YMU and MIC1557 feature a CS input. With
a logic-low signal, CS places the part into a <1µA
shutdown state. If unused, the CS input must be pulled
up.
Figure 4. MIC1557 Oscillator Configuration
Falling-Edge Triggered Monostable Circuit
The MIC1555 may be triggered by an AC-coupled fallingedge, as shown in Figure 5. The RC time constant of the
input capacitor and pull-up resistor should be less than
the output pulse time, to prevent multiple output pulses. A
diode across the timing resistor provides a fast reset at
the end of the positive timing pulse.
Figure 2. Oscillator Diagram
The MIC1555 or MIC1557 can be used to construct an
oscillator.
The frequency of an astable oscillator is:
f =
1
k 1RC
where:
f = frequency (Hz)
Figure 5. Falling Edge Trigger Configuration
k1 = Constant (see Typical Characteristics)
R = Resistance (Ω)
C = Capacitance (F)
To use the MIC1555 as an oscillator, connect TRG to
THR.
Figure 3. MIC1555 Oscillator Configuration
August 12, 2015
12
Revision 6.1
Micrel, Inc.
MIC1555/1557
Rising-Edge Triggered Monostable Circuit
The MIC1555 may be triggered by an AC-coupled risingedge, as shown in Figure 6. The pulse begins when the
ac-coupled input rises, and a diode from the output holds
the THR input low until TRG discharges to 1/3VS. This
circuit provides a low-going output pulse.
Inverting Schmitt Trigger
As shown in Figure 7, the trip points of the MIC1555/7
are defined as 1/3 and 2/3VS, which allows either device
to be used as a signal conditioning inverter, with
hysteresis. A slowly changing input on T/T will be
converted to a fast rise or fall-time opposite direction railto-rail output voltage. This output maybe used to directly
drive the gate of a logic-level P-channel MOSFET with a
gate pull-up resistor. This is an inverted logic low-side
logic level MOSFET driver. A standard N-channel
MOSFET may be driven by a second MIC1555/7,
powered by 12V to 15V, to level-shift the input.
Figure 6. Rising Edge Trigger Configuration
Accuracy
The two comparators in the MIC1555/7 use a resistor
voltage divider to set the threshold and trigger trip points
to approximately 2/3 and 1/3 of the input voltage,
respectively. Since the charge and discharge rates of an
RC circuit are dependent on the applied voltage, the
timing remains constant if the input voltage varies. If a
duty cycle of exactly 50% (or any other value from 1 to
99%), two resistors (or a variable resistor) and two diodes
are needed to vary the charge and discharge times. The
forward voltage of diodes varies with temperature, so
some change in frequency will be seen with temperature
extremes, but the duty cycle should track. For absolute
timing accuracy, the MIC1555/7 output could be used to
control constant current sources to linearly charge and
discharge the capacitor, at the expense of added
components and board space.
Figure 7. Schmitt Trigger
Charge-Pump Low-Side MOSFET Drivers
A standard MOSFET requires approximately >5V to fully
enhance the gate for minimum RDS(ON). Substituting a
logic-level MOSFET reduces the required gate voltage,
allowing an MIC1557 to be used as an inverting Schmitt
trigger, described above. An MIC1557 may be configured
as a voltage quadrupler to boost a 5V input to over 15V
to fully enhance an N-channel MOSFET which may have
its drain connected to a higher voltage, through a highside load. ATTL high signal applied to CS enables a
10kHz oscillator, which quickly develops 15V at the gate
of the MOSFET, clamped by a Zener diode. A resistor
from the gate to ground ensures that the FET will turn off
quickly when the MIC1557 is turned off.
Long Time Delays
Timing resistors larger than 1MΩ or capacitors larger
than 10µF are not recommended due to leakage current
inaccuracies. Time delays greater than 10 seconds are
more accurately produced by dividing the output of an
oscillator by a chain of flip-flop counter stages. To
produce an accurate one-hour delay, for example, divide
a 4.55Hz MIC1557 oscillator by 16,384 (4000hex, 214)
using a CD4020 CMOS divider. 4.5Hz may be generated
with a 1µF CT and approximately 156kΩ.
Figure 8. Charge Pump
August 12, 2015
13
Revision 6.1
Micrel, Inc.
MIC1555/1557
Audible Voltmeter
If an additional charge or discharge source is connected
to the timing capacitor, the frequency may be shifted by
turning the source on or off. An MIC1555 oscillator,
powered by the circuit under test, may be used to drive a
small loud speaker or piezo-electric transducer to provide
a medium frequency for an open or high impedance state
at the probe. A high tone is generated for a high level,
and a lower frequency for a logic low on the probe.
Figure 9. Audible Voltmeter
August 12, 2015
14
Revision 6.1
Micrel, Inc.
MIC1555/1557
Package Information and Recommended Land Pattern(7)
5-Pin SOT-23 (M5)
Note:
7. Package information is correct as of the publication date. For updates and most current information, go to www.micrel.com.
August 12, 2015
15
Revision 6.1
Micrel, Inc.
MIC1555/1557
Package Information and Recommended Land Pattern(7) (Continued)
5-Pin Thin SOT-23 (D5)
August 12, 2015
16
Revision 6.1
Micrel, Inc.
MIC1555/1557
Package Information and Recommended Land Pattern(7) (Continued)
10-Pin 2mm × 2mm UTDFN (MU)
August 12, 2015
17
Revision 6.1
Micrel, Inc.
MIC1555/1557
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA
TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com
Micrel, Inc. is a leading global manufacturer of IC solutions for the worldwide high performance linear and power, LAN, and timing & communications
markets. The Company’s products include advanced mixed-signal, analog & power semiconductors; high-performance communication, clock
management, MEMs-based clock oscillators & crystal-less clock generators, Ethernet switches, and physical layer transceiver ICs. Company
customers include leading manufacturers of enterprise, consumer, industrial, mobile, telecommunications, automotive, and computer products.
Corporation headquarters and state-of-the-art wafer fabrication facilities are located in San Jose, CA, with regional sales and support offices and
advanced technology design centers situated throughout the Americas, Europe, and Asia. Additionally, the Company maintains an extensive network
of distributors and reps worldwide.
Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this datasheet. This
information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry,
specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual
property rights is granted by this document. Except as provided in Micrel’s terms and conditions of sale for such products, Micrel assumes no liability
whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties
relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right.
Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product
can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical
implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A
Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully
indemnify Micrel for any damages resulting from such use or sale.
© 2004 Micrel, Incorporated.
August 12, 2015
18
Revision 6.1