Part Number: XZMDKDGCBD45S SunLED Corporation Features

Part Number: XZMDKDGCBD45S
3.5x2.8mm PLCC4 SMD LED
Package Schematics
Features
● Ideal for indication light on hand held products
● Long life and robust package
● Variety of lens types and color choices available
● Package: 1500pcs / reel
● Moisture sensitivity level : level 3
● RoHS compliant
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Specifications are subject to change without notice.
Absolute Maximum Ratings
(TA=25°C)
MDK
(AlGaI
nP)
DG
(InGa
N)
CBD
(InGa
N)
Unit
3.3
3.3
V
mA
Forward Voltage (Max.)
(IF=20mA)
VF
2.5
4.1
4
V
150
mA
Reverse Current (Max.)
(VR=5V)
IR
10
50
50
uA
123
120
mW
λP
650
515
468
nm
450
250
V
Wavelength of Peak
Emission (Typ.)
(IF=20mA)
Wavelength of Dominant
Emission (Typ.)
(IF=20mA)
λD
630
525
470
nm
Spectral Line Full Width
At Half-Maximum (Typ.)
(IF=20mA)
△λ
28
30
25
nm
C
35
45
100
pF
5
5
V
Forward Current
IF
30
30
30
Forward Current (Peak)
1/10 Duty Cycle
0.1ms Pulse Width
iFS
185
150
Power Dissipation
PD
75
-
Storage Temperature
Tstg
-40 ~ +85
°C
Capacitance (Typ.)
(VF=0V, f=1MHz)
Part
Number
XZMDKDGCBD45S
Unit
1.95
5
TA
CBD
(InGaN)
VF
VR
Operating Temperature
MDK
DG
(AlGaInP) (InGaN)
Forward Voltage (Typ.)
(IF=20mA)
Reverse Voltage
Electrostatic Discharge Threshold
(HBM)
Operating Characteristics
(TA=25°C)
Emitting
Color
Emitting
Material
Red
AlGaInP
Green
InGaN
Blue
InGaN
Luminous
Intensity
(IF=20mA)
mcd
Lens-color
Water Clear
Apr 19,2011
min.
typ.
200
317
650
480
695
515
70
128
468
XDSB4856
SunLED Corporation
Wavelength
nm
λP
V3
Viewing
Angle
2θ 1/2
120°
Layout: Maggie L.
P. 1/5
Part Number: XZMDKDGCBD45S
3.5x2.8mm PLCC4 SMD LED
Handling Precautions
Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic
significantly reduces thermal stress, it is more susceptible to damage by external mechanical force.
As a result, special handling precautions need to be observed during assembly using silicone encapsulated
LED products. Failure to comply might lead to damage and premature failure of the LED.
1. Handle the component along the side surfaces by using forceps or appropriate tools.
2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry.
3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or
damage the internal circuitry.
4.1. The outer diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks. The inner
diameter of the nozzle should be as large as possible.
4.2. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup.
4.3. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise
pickup and avoid damage during production.
5. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances.
Apr 19,2011
XDSB4856
SunLED Corporation
V3
Layout: Maggie L.
P. 2/5
Part Number: XZMDKDGCBD45S
3.5x2.8mm PLCC4 SMD LED
™ MDK
™ DG
™ CBD
Apr 19,2011
XDSB4856
SunLED Corporation
V3
Layout: Maggie L.
P. 3/5
Part Number: XZMDKDGCBD45S
3.5x2.8mm PLCC4 SMD LED
LED is recommended for reflow soldering and
soldering profile is shown below.
™ The device has a single mounting surface.
The device must be mounted according to the
specifications.
™ Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
™ Tape Specification (Units : mm)
™ Reel Dimension
Remarks:
If special sorting is required (e.g. binning based on forward voltage, Luminous intensity / luminous flux, or wavelength),
the typical accuracy of the sorting process is as follows:
1. Wavelength: +/-1nm
2. Luminous intensity / luminous flux: +/-15%
3. Forward Voltage: +/-0.1V
Note: Accuracy may depend on the sorting parameters.
Apr 19,2011
XDSB4856
SunLED Corporation
V3
Layout: Maggie L.
P. 4/5
Part Number: XZMDKDGCBD45S
3.5x2.8mm PLCC4 SMD LED
PACKING & LABEL SPECIFICATIONS
Apr 19,2011
XDSB4856
SunLED Corporation
V3
Layout: Maggie L.
P. 5/5