Specifications

Enclosed Switch
SHL
CSM_SHL_DS_E_4_1
Compact, General-purpose Horizontal
Switches.
Models for Microloads Added to Series
• Approved by EN, UL, CSA, and CCC (Chinese standard).
(Ask your OMRON representative for information on approved
models.)
• Incorporates a switch with a durable coil spring in a tough, highprecision case.
• Compact and uses a single basic switch for applications where
strength is required.
• Models for microloads and models with operation indicators
added to series.
• Terminal protective cover can be switched to wire cable from
either the left or right.
• Sealing characteristics that meet IEC IP67 degree of protection.
For the most recent information on models that have been certified for
safety standards, refer to your OMRON website.
Be sure to read Safety Precautions on page 7 and Safety Precautions for All
Limit Switches.
Ordering Information
Switches
Type
Actuator
Plunger
Standard
Model
Micro load
Model
SHL-D55
SHL-D55-01
SHL-Q55
SHL-Q55-01
SHL-Q2255
SHL-Q2255-01
SHL-Q2155
SHL-Q2155-01
Short hinge lever
SHL-W55
SHL-W55-01
Hinge lever
SHL-W155
SHL-W155-01
Panel mount
plunger
Panel mount roller
plunger
Panel mount
crossroller
plunger
Type
Actuator
Short hinge roller
lever
Hinge roller lever
One-way action
short hinge roller
lever
One-way action
hinge roller lever
Standard
Model
Micro load
Model
SHL-W255
SHL-W255-01
SHL-W2155
SHL-W2155-01
SHL-W355
SHL-W355-01
SHL-W3155
SHL-W3155-01
Note: Models are also available with molded terminals and with molded
terminals and operation indicators. Refer to page 6.
Switches (Molded Terminal Models)
Without Operation Indicator, Lead Wired on Right
Standard
Model
SHL-D55-MR
SHL-Q55-MR
SHL-Q2155-MR
SHL-Q2255-MR
SHL-W55-MR
Micro load
Model
SHL-W155-MR
SHL-W255-MR
SHL-W2155-MR
SHL-W355-MR
Model
SHL-D55-01MR
SHL-Q55-01MR
SHL-Q2155-01MR
SHL-Q2255-01MR
SHL-W55-01MR
Model
SHL-W255-01MR
SHL-W2155-01MR
Without Operation Indicator, Lead Wired on Left
Standard
Model
SHL-D55-ML
SHL-Q2155-ML
SHL-Q2255-ML
SHL-W55-ML
SHL-W155-ML
Model
SHL-W255-ML
SHL-W2155-ML
Micro load
Model
SHL-Q2255-01ML
SHL-W2155-01ML
1
SHL
Without Operation Indicator, Lead Wired from Bottom
Standard
Model
Model
SHL-W155-MD
SHL-W255-MD
SHL-W2155-MD
SHL-W355-MD
SHL-D55-MD
SHL-Q55-MD
SHL-Q2155-MD
SHL-Q2255-MD
SHL-W55-MD
Micro load
Model
SHL-Q2255-01MD
Operation Indicator, Lead Wired on Right
Standard
Model
Model
SHL-Q2255-L3MR
SHL-W155-L3MR
SHL-W255-L3MR
SHL-W2155-L3MR
SHL-D55-L4MR
SHL-Q55-L4MR
SHL-Q2155-L4MR
SHL-Q2255-L4MR
SHL-W255-L4MR
SHL-W2155-L4MR
SHL-W355-L4MR
SHL-D55-LMR
SHL-Q55-LMR
SHL-Q2155-LMR
SHL-Q2255-LMR
SHL-W155-LMR
SHL-W255-LMR
SHL-W2155-LMR
SHL-D55-L2MR
SHL-Q2255-L2MR
SHL-D55-L3MR
SHL-Q55-L3MR
SHL-Q2155-L3MR
Micro load
Model
SHL-Q2255-01LMR
SHL-W255-01LMR
SHL-D55-01L3MR
SHL-Q2155-01L3MR
SHL-Q2255-01L3MR
SHL-Q2155-01L4MR
SHL-Q2255-01L4MR
SHL-W255-01L4MR
SHL-W2155-01L4MR
Operation Indicator, Lead Wired on Left
Standard
Model
Model
SHL-W55-L3ML
SHL-W155-L3ML
SHL-W255-L3ML
SHL-Q2255-L4ML
SHL-W155-L4ML
SHL-Q55-LML
SHL-Q2255-LML
SHL-W155-LML
SHL-W255-LML
SHL-W2155-LML
SHL-Q55-L2ML
SHL-Q2255-L3ML
Micro load
Model
SHL-W255-01LML
SHL-W2155-01LML
SHL-Q2255-01L3ML
SHL-W255-01L4ML
Operation Indicator, Lead Wired from Bottom
Standard
Model
Model
SHL-Q2255-L4MD
SHL-W255-L4MD
SHL-W2155-L4MD
SHL-Q2255-LMD
SHL-W255-LMD
SHL-Q55-L3MD
Micro load
Model
SHL-Q55-01LMD
SHL-Q2255-01L4MD
Specifications
Approved Standards
Agency
UL
CSA
Standard
UL508
CSA C22.2
No. 14
File No.
E76675
LR45746
TÜV Rheinland
EN60947-5-1
J50062486
CCC (CQC)
GB14048.5
2003010305072162
Approved models
General-purpose models listed on
page 1.
All SHL models listed in this
datasheet.
Ask your OMRON representative for
information on approved models.
2
SHL
Ratings
Rated
voltage
125 VAC
250 VAC
480 VAC
8 VDC
14 VDC
30 VDC
125 VDC
250 VDC
Approved Standard Ratings
Non-inductive load (A)
Resistive
Lamp load
load
NC
NO
NC
NO
10
1.5
10
1.5
2
−
10
2
10
2
5
1.5
0.4
0.4
0.2
0.2
NC
NO
Inrush
current
Inductive load (A)
Inductive
Motor load
load
NC
NO
NC
NO
3
2.5
2
1.5
−
−
5
2
5
2
1.5
1.5
0.05
0.05
0.03
0.03
15 A max.
15 A max.
Note: 1. The above figures are for steady-state currents.
2. Inductive loads have a power factor of 0.4 min. (AC) and a time
constant of 7 ms max. (DC).
3. Lamp load has an inrush current of 10 times the steady-state current.
4. Motor load has an inrush current of 6 times the steady-state current.
Micro load models
Rated
voltage
125 VAC
8 VDC
14 VDC
30 VDC
Non-inductive load (A)
Resistive load
NC
NO
0.1
0.1
0.1
0.1
TÜV (EN60947-5-1), CCC (GB14048.5)
Category and rating
I the
SHL-@55
Model
AC-15 2 A/125 V
DC-12 2 A/48 V
5A
5A
SHL-@55-01
AC-14 0.1 A/125 V
DC-12 0.1 A/48 V
SHL-@55-L
AC-15 2 A/125 V
SHL-@55-01L
AC-14 0.1 A/125 V
0.5 A
0.5 A
SHL-@55-01L2
DC-12 0.1 A/12 V
SHL-@55-L3
DC-12 2 A/24 V
SHL-@55-01L3
DC-12 0.1 A/24 V
SHL-@55-L4
DC-12 2 A/24 V
SHL-@55-01L4
DC-12 0.1 A/24 V
SHL-@55-L5
DC-12 2 A/48 V
0.5 A
0.5 A
5A
5A
0.5 A
5A
0.5 A
5A
SHL-@55-01L5
DC-12 0.1 A/48 V
Note: "AC-15 2 A/125 V" indicates the following.
Application category: AC-16
Rated operating current (Ie): 2 A
Rated operating voltage (Ue): 125 V
0.5 A
UL/CSA
A300
Rated
voltage
120 VAC
240 VAC
Current (A)
Make
Break
60
6
30
3
Carry
current
10 A
Characteristics (For SHL-W155)
Volt-amperes (V)
Make
Break
7,200
720
Engineering Data
IP67 (EN60947-5-1)
10,000,000 operations min.
500,000 operations min.
0.1 mm/s to 0.5 m/s (hinge lever models)
120 operations/min
30 operations/min
50/60 Hz
100 MΩ min. (at 500 VDC)
15 mΩ max. (initial value for the built-in switch when
tested alone)
Contact resistance
Between terminals of the
same polarity
Dielectric strength Between each terminal and
non-current-carrying metal
part
Rated insulation voltage (Ui)
Pollution degree (operating environment)
Short-circuit protective device (SCPD)
Conditional short-circuit current
Conventional enclosed thermal current (Ithe)
Protection against electric shock
OFF reverse voltage
Vibration resistance Malfunction
Destruction
Shock
resistance
Malfunction
Ambient operating temperature
Ambient operating humidity
Weight
Electrical Durability
(Ambient temperature: +5°C to +35°C,
Ambient humidity: 40% to 50%RH)
Durability (x 104 operations)
Degree of protections
Mechanical
Durability
Electrical
Operating speed
Mechanical
Operating
frequency
Electrical
Rated frequency
Insulation resistance
1,000 VAC, 50/60 Hz for 1 min
1,000
700
500
300
250 VAC
100
70
50
2,000 VAC, 50/60 Hz for 1 min/Uimp at 2.5 kV
(EN60947-5-1)
150 V (EN60947-5-1)
3 (EN60947-5-1)
10 A fuse type gI or gG (IEC60269)
100 A (EN60947-5-1)
5 A (EN60947-5-1)
Class II (grounding not required with double insulation)
1,000 VAC max., 300 VDC max. (EN60947-5-1)
10 to 55 Hz, 1.5-mm double amplitude
1,000 m/s2 max.
300 m/s2 max.
−10°C to +80°C (with no icing)
35% to 95%RH
Approx. 62 to 72 g
Structure and Nomenclature
Structure
Operating frequency:
30 operations/min.
(cos dia. = 1)
30
10
7
5
3
1
0
1
2
3
4
5
6
7
8
9
10
Switching current (A)
Note: 1. The figures at the left are initial values.
2. The ratings at the left may vary depending on
the model. Contact your OMRON
representative for further details.
*1. The head section of the plunger type SHL-D(Q)@@ is
excluded.
*2. Durability values are calculated at an operating
temperature of +5°C to +35°C, and an operating
humidity of 40% to 70%RH.
*3. The values are for the plunger-type models.
Contact Form
Movable plunger
(COM) 1
Rubber cap (NBR)
2 (NC)
4 (NO)
Die-cast case
(zinc die-cast)
Seal rubber (NBR)
Terminal protection cover
Screw terminal
Seal packing (NBR)
3
SHL
Dimensions and Operating Characteristics
Switches
(Unit: mm)
(Note: Omitted dimensions are the same as those of the plunger models.)
Plunger
SHL-D55
SHL-D55-01
7.8 dia. *
Two, 4.2 dia.
holes
PT
42.5
17.5
M14 × 1
Operating Characteristics
10
OP
19
16.9
16
9.6
3.5
16.5 ±0.2
13
15 × 15
45.6
Terminal
protective
cover
Rubber seal
54.6
Model SHL-D55
SHL-D55-01
Operating force
Release force
Pretravel
Overtravel
Movement
Differential
OF
RF
PT
OT
MD
max.
min.
max.
min.
max.
9.81 N
1.96 N
1.5 mm
2 mm
0.5 mm
Free Position
Operating Position
FP
OP
max.
−
34±0.8 mm
73.5
* Stainless steel pin plunger
Panel Mount Plunger
SHL-Q55
SHL-Q55-01
7.8 dia. *
M14 × 1
PT
Two hexagon
nut
(thickness: 2.5,
width: 17)
10
OP
19
16.9
16
9.6
3.5
16.5 ±0.2
13
Model SHL-Q55
Operating Characteristics SHL-Q55-01
OF
RF
PT
OT
MD
max.
min.
max.
min.
max.
9.81 N
1.96 N
1.5 mm
2 mm
0.5 mm
FP
OP
max.
−
34±0.8 mm
15 × 15
* Stainless steel pin plunger
Panel Mount Roller Plunger
SHL-Q2255
SHL-Q2255-01
11 dia. × 4.7 *
PT
M14 × 1
10
Two hexagon
nut
(thickness: 2.5
width: 17)
OP
19
16.9
16
9.6
3.5
16.5 ±0.2
13
Model SHL-Q2255
Operating Characteristics SHL-Q2255-01
OF
RF
PT
OT
MD
max.
min.
max.
min.
max.
9.81 N
1.96 N
1.5 mm
2 mm
0.5 mm
FP
OP
max.
−
43±0.8 mm
15 × 15
* Stainless sintered alloy roller
Panel Mount Crossroller Plunger
SHL-Q2155
SHL-Q2155-01
11 dia. × 4.7 *
PT
M14 × 1
10
Two hexagon
nut
(thickness: 2.5
width: 17)
OP
19
16.9
16
9.6
3.5
16.5 ±0.2
13
Model SHL-Q2155
Operating Characteristics SHL-Q2155-01
OF
RF
PT
OT
MD
max.
min.
max.
min.
max.
9.81 N
1.96 N
1.5 mm
2 mm
0.5 mm
FP
OP
max.
−
43±0.8 mm
15 × 15
* Stainless sintered alloy roller
Short Hinge Lever
SHL-W55
SHL-W55-01
35R
6.8
t=1*
42.5
16.5
Model SHL-W55
Operating Characteristics SHL-W55-01
13
17.5
24
16.9
FP
21
16
OP
16
9.6
3.5
16.5 ±0.2
13
OF
RF
PT
OT
MD
max.
min.
max.
min.
max.
3.14 N
0.78 N
8 mm
3 mm
2.5 mm
FP
OP
max.
29.5 mm
21.5±1 mm
15 × 15
* Stainless steel lever
Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
4
SHL
Hinge Lever
SHL-W155
SHL-W155-01
t=1*
6.8
53R
Model HL-W155
Operating Characteristics SHL-W155-01
17.5
FP
24
16.9
21
16
OP
16
9.6
3.5
16.5 ±0.2
13
OF
RF
PT
OT
MD
max.
min.
max.
min.
max.
2.35 N
0.44 N
13 mm
5 mm
4 mm
FP
OP
max.
34.5 mm
21.5±1 mm
15 × 15
* Stainless steel lever
Short Hinge Roller Lever
SHL-W255
SHL-W255-01
9.5 dia. × 4.8 *
Model SHL-W255
Operating Characteristics SHL-W255-01
31
R
6.8
FP
24
16.9
OP
21
16
16
9.6
3.5
16.5 ±0.2
13
OF
RF
PT
OT
MD
max.
min.
max.
min.
max.
3.92 N
0.78 N
8 mm
3 mm
2.5 mm
FP
OP
max.
41 mm
33±1 mm
15 × 15
* Sintered stainless roller
Hinge Roller Lever
SHL-W2155
SHL-W2155-01
9.5 dia. × 4.0 *
6.8
Model SHL-W2155
Operating Characteristics SHL-W2155-01
R
51
FP
24
16.9
OP
21
16
16
9.6
3.5
16.5 ±0.2
13
OF
RF
PT
OT
MD
max.
min.
max.
min.
max.
2.55 N
0.49 N
13 mm
5.5 mm
4 mm
FP
OP
max.
46.5 mm
33.5±1 mm
15 × 15
* Sintered stainless roller
R
One-way Action Short Hinge Roller Lever
SHL-W355
6.8
SHL-W355-01
Model SHL-W355
Operating Characteristics SHL-W355-01
90°
35.5
Operating direction
9.5 dia. × 4.0 *
FP
OP
24
16.9
21
16
16
9.6
3.5
16.5 ±0.2
13
OF
RF
PT
OT
MD
max.
min.
max.
min.
max.
3.92 N
0.78 N
8 mm
3 mm
2.5 mm
FP
OP
max.
52.5 mm
44.5± 1 mm
15 × 15
* Stainless sintered roller
One-way Action Hinge Roller Lever
SHL-W3155
SHL-W3155-01
6.8
Model SHL-W3155
Operating Characteristics SHL-W3155-01
90°
52
Operating direction
.5
R
9.5 dia. × 4.0 *
FP
OP
24
16.9
21
16
16
9.6
3.5
16.5 ±0.2
13
OF
RF
PT
OT
MD
max.
min.
max.
min.
max.
2.55 N
0.49 N
13 mm
5.5 mm
4 mm
FP
OP
max.
57.5 mm
44.5±1 mm
15 × 15
* Stainless sintered roller
Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
5
SHL
Molded Terminal Models
Use of the molded terminal model is
recommended in locations subject to
excessive dust, oil drips, or moisture.
All types of SHL Switches can be fabricated
into a molded terminal version. In this case,
the molded terminal model will have the
same dimensions and operating
characteristics as the basic model from
which the molded terminal model is
fabricated.
How to order
Suffix by Location of Lead Outlet
Location of
lead outlet
(Refer to
left figure)
Right-hand
Left-hand
Underside
Example:
Basic type: SHL-Q2255
Location of lead outlet: Right side
Length of lead: 3 m (V.C.T.F. lead)
When placing your order for the above
Switch specify the model number as SHLQ2255-MR VCTF 3M.
Model (suffix)
Terminal COM, NC, NO
-MR
-ML
-MD
Note: The above suffixes can be added to the
model numbers given on page 1 to specify
molded terminals.
Lead Supplies
Specifications
Leads
Nominal cross-sectional
area (mm2)
No. of conductors/cond.
dia.
External diameter (mm)
MR
ML
MD
VCTF
(Vinyl cabtire cable)
0.75
30/0.18
3-conductor 7 dia.
Black: COM
White: NO
Red: NC
3 (standard)
Terminal connections
Length (m)
Operation Indicator-equipped Models
The molded terminal model may be equipped with an operation indicator (neon lamp or LED) upon request to facilitate maintenance and
inspection.
The operation indicator is designed to illuminate when the Switch is not operating. (Because of the molded terminal model, any change
to the Switch wiring cannot be made.)
Note: Refer to the previous table for model numbers for Switch with molded terminals and operation indicators.
For AC
• The applicable voltage is 90 to 250 VAC (microload models: 90 to
125 VAC).
Matte finish
For DC
• LED indicator is provided.
• As a rectifier stack is incorporated, into the unit and no directionality
exists for connection of + and −, this type can also be operated on
AC.
• The voltage specifications are given below.
• Voltage ratings of LED indicators are as shown in the table below.
Model
Neon lamp
Transparent terminal protection cover
• Operating characteristics are the same as the basic model from
which the operation indicator equipped model is fabricated.
• Dimension are the same as the standard model.
Example:
Basic type: SHL-Q2255-MR
When placing your order for the molded terminal model with an neon
lamp operation indicator, specify the model number as SHL-Q2255LMR.
Contact Circuit
L2
L3
L4
Voltage rating
(V)
12
24
24
Leakage current
(mA)
Approx. 2.4
Approx. 2
Approx. 1.2
Internal
resistance (kΩ)
4.3
10
18
Example:
Basic type: SHL-Q2255-MR
When placing your order for the molded terminal with an LED
indicator rated at 12 V, specify the model number as SHL-Q2255L2MR.
Contact Circuit
Power supply
Built-in switch
Power supply
Built-in switch
Load
Load
Resistor
LED
Neon lamp R = 240 kΩ
6
SHL
Safety Precautions
Refer to Safety Precautions for All Limit Switches.
Precautions for Correct Use
Operating Environment
Micro Load Models
• Seal material may deteriorate if a Switch is used outdoor or where
subject to special cutting oils, solvents, or chemicals. Always
appraise performance under actual application conditions and set
suitable maintenance and replacement periods.
• Install Switches where they will not be directly subject to cutting
chips, dust, or dirt. The Actuator and Switch must also be protected
from the accumulation of cutting chips or sludge.
Not Suitable
Micro Load Applicable Ranges
Voltage (VDC)
Suitable
When using a Limit Switch for opening or closing micro-load circuit
(zones 1 through 3), contact failure may occur if a Limit Switch with
ordinary contact specifications is used. Therefore, when using Limit
Switches in the micro-load range, use ones with contact
specifications that are suited to each zone. Use the SHL-@-01 micro
load models within the zones (1 through 3) shown in the following
diagram.
• Constantly subjecting a Switch to vibration or shock can result in
wear, which can lead to contact interference with contacts,
operation failure, reduced durability, and other problems.
Excessive vibration or shock can lead to false contact operation or
damage. Install Switches in locations not subject to shock and
vibration and in orientations that will not produce resonance.
• The Switches have physical contacts. Using them in environments
containing silicon gas will result in the formation of silicon oxide
(SiO2) due to arc energy. If silicon oxide accumulates on the
contacts, contact interference can occur. If silicon oil, silicon filling
agents, silicon cables, or other silicon products are present near the
Switch, suppress arcing with contact protective circuits (surge
killers) or remove the source of silicon gas.
Connections
Be sure to connect a fuse with a breaking current 1.5 to 2 times the
rated current to the Limit Switch in series in order to protect the Limit
Switch from damage due to short-circuiting.
When using the Limit Switch under the EN ratings, use a gI or gG 10A fuse that conforms to IEC60269.
Mounting
• Secure the Switch with two M4 screws and washers.
The tightening torque applied to each terminal must be 1.18 to
1.37 N·m. Tighten the screws to the specified torque. An excessive
tightening torque may damage the Switch and cause a malfunction.
• When mounting the panel mount-type Switch with screws on a side
surface, remove the hexagonal nuts from the actuator.
Mounting Holes
5 mW
800 mW
0.16 mA
30
26 mA
24
Operating range for
micro-load models
Operating
range for
standard
models
12
Unusable
range
5
1 mA
0
0.1
1
100 mA 160 mA
10
100
1,000
Current (mA)
The above diagram is for standard conditions (+5°C to +35°C, 40% to
70%RH). Since the values vary depending on the operating
environment conditions, contact your OMRON representative for
further details.
Tightening Torque
• A loose screw may result in a malfunction. Be sure to tighten each
screw to the proper tightening torque as shown below.
No.
Type
1
Terminal screw (M3 screw)
Mounting screw
(M4 screw)
2
Appropriate tightening
torque
0.24 to 0.44 N·m
1.18 to 1.37 N·m
• When wiring, use M3 round solderless terminals and apply
insulation shielding to the connections. Tighten the terminals
screws to 0.24 to 0.44 N·m.
Operating Stroke
Two, 4.3-dia. or
M4 screw holes
Ensure that the operating stroke for roller plunger models is within
the set position display.
16.5 ± 0.2
Operating stroke
range
• When mounting the panel mount type (SHL-Q55, SHL-Q2255, or
SHL-Q2155) on a panel, tighten the hexagonal nuts of the actuator
to a torque less than 4.90 to 7.84 N·m.
Mounting Holes
14.5
+0.2
0 dia.
Reference
Others
The standard seal rubber for the lead wire outlet is one that allows 6to 8-dia. cables. The appropriate nominal cross-section of the lead
wire is 0.75 mm2. (When the sealing capability is required over a long
period of time, use mold specifications.)
7
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron
disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER
ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at
Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount
equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,
repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or
electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above
warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
2013.11
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2013 All Right Reserved.