New Product News Slim D-Sub Connector XM3-LS Space-saving 9-pin Slim D-sub Connectors for Boards • Board mounting area is reduced by 33% (compared with previous models) using depth of 8.4 mm. • Nine D-sub right-angle DIP terminals. • Mounting board thickness of either 1.0 mm or 1.6 mm. Footprint on board reduced by 33% over previous models. 12.6 mm 8.4 mm Reduced by 4.2 mm. Previous model ■Ratings and Characteristics Slim model ■Materials and Finish Rated current 3A Rated voltage 300 VAC Housing Contact resistance 20 mΩ max. (at 20 mVDC, 100 mA max.) Insulation resistance 1,000 MΩ min. (at 500 VDC for 1 min) Withstand voltage 1,000 VAC for 1 min (leakage current: 1 mA max.) Insertion durability 100 times Operating temperature −25 to 105°C Contacts Shell Fiber-glass reinforced PBT resin (UL94V-0)/black Socket Phosphor bronze/nickel base, flash gold plated Plug Brass/nickel base, flash gold plated Steel/nickel plated Anchors Grounding fixture Socket M2.6 × 0.45: Steel/nickel plated #4-40UNC: Stainless steel Plug Stainless steel Phosphor bronze/tin plated ■Ordering Information Socket Plug Minimum ordering quantity (pieces) Appearance No. of contacts Anchors M2.6 × 0.45 #4-40 UNC 9 XM3B-0942-112LS XM3B-0942-132LS 80 Minimum ordering quantity (pieces) Appearance No. of contacts Anchors M2.6 × 0.45 #4-40 UNC 9 XM3C-0942-112LS XM3C-0942-132LS 80 1 XM3-LS Slim D-Sub Connector ■Dimensions (Unit: mm) 30.8 24.99 16.3 2.74 Mounting Holes (BOTTOM VIEW) 14.7 Anchors Nin e, 1 +0 .1 Tw o, 3 . 12.5 7.9 2± 1.905 (2.6) 5.85 dia . 0 0.1 dia . Board edge Note: Applicable board thickness: 1.0 or 1.6 mm. Plug XM3C-0942-1@2LS Panel Cutout 14.5 5.8 Anchors 31.0 min. 5.8 Two, R3.2 11.4 min. 6.4 min. 8.3 30.8 24.99 16.92 2.74 12.5 2.84 24.99 ± 0.05 2.74 ± 0.05 4.9 max. 1.905 ± 0.05 2.84 Socket XM3B-0942-1@2LS Four, R2.5 (2.6) 1.905 5.85 Note: Applicable panel thickness is 1.2 mm max. Note: The mounting hole and panel cutout dimensions are the same for the Sockets and Plugs. ■Safety Precautions Precautions for Correct Use • Insert the connector into the board and then simultaneously dip-solder the connector terminals and lock pins to the board. • Pull or push the connector straight in or out when you connect or disconnect it. Twisting it may cause damage or faulty contact. • Do not remove the anchors from the connector. Removing the anchors may cause damage or faulty contact. Board (t=1.6 mm) Lock pin grounding fixture ●Automatic Soldering Automated Soldering Conditions (Jet Flow) (1) Soldering temperature: 250 ± 5°C (2) Continuous soldering time: 5 ± 1 s max. Board (t=1.0 mm) Lock pin grounding fixture • Application examples provided in this document are for reference only. In actual applications, confirm equipment functions and safety before using the product. • Consult your OMRON representative before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems or equipment that may have a serious influence on lives and property if used improperly. Make sure that the ratings and performance characteristics of the product provide a margin of safety for the system or equipment, and be sure to provide the system or equipment with double safety mechanisms. Note: Do not use this document to operate the Unit. OMRON Corporation Electronic and Mechanical Components Company Contact: www.omron.com/ecb Cat. No. G022-E1-02 0413(1111)(W)