rf amplifier model qbh

Available as:
RF AMPLIFIER
MODEL QBH-1423PM
Features
!
!
!
!
QBH-1423PM, 4 Pin TO-8 (T4)
QBH-5023PM, 4 Pin Surface Mount (SM3)
QBH-9-1423PM, Connectorized Housing (H1)
Typical Intermodulation Performance at 25ºC
Superior Phase Noise Performance
Replaces Avantek’s “1023” Design
Operating Temp. -55 ºC to +85 ºC
Environmental Screening Available
Second Order Harmonic Intercept Point ....... +46 dBm (Typ.)
Second Order Two Tone Intercept Point ........ +40 dBm (Typ.)
Third Order Two Tone Intercept Point ............ +34 dBm (Typ.)
Absolute Maximum Ratings
Specifications
CHARACTERISTIC
Frequency
TYPICAL
Ta= 25 ºC
10 - 1000 MHz
Gain (dB)
13.0
12.0 Min.
Gain Flatness (dB)
Power @ 1 dB Comp.
(dBm) (10-500 MHz)
± 0.25
± 0.75 Max.
28.0
26.5
25.5 Min.
25.0 Min.
-17
-15 Max.
1.5:1
1.5:1
6.0
+15
195
2.0:1 Max.
2.0:1 Max.
9.0 Max.
+15
210 Max.
(500-1000 MHz)
Reverse
Isolation (dB)
VSWR
In
Out
Noise Figure (dB)
Power
Vdc
mA
Ambient Operating Temperature ................ -55ºC to +100 ºC
Storage Temperature .................................-62ºC to +125 ºC
DC Voltage .......................................................... +17 Volts
Continuous RF Input Power1 .......................................................... +17 dBm
Short Term RF Input Power1 ..... 100 Milliwatts (1 Minute Max.)
MIN/MAX
Ta = -55 ºC to +85 ºC
10 - 1000 MHz
MTBF Calculation for Ground Benign Environment
@ 25ºC .................................................1,674,483.59 hrs
25ºC Phase Noise Performance in dBc/Hz @ 600 MHz2
Frequency offset
10 Hz
100 Hz
1 kHz
10 kHz
100 kHz
1 MHz
Notes: Care should always be taken to effectively ground the case of each unit.
Measured in a 50 Ohm system @ +15 Volts DC nominal unless otherwise noted.
1
2
Typical
-150
-160
-175
-180
-180
-180
Guaranteed
-145
-155
-170
-175
-175
-175
RF output terminated into 50 Ohms.
Phase noise performance may vary within the frequency band.
Typical Performance Data
Gain (dB)
15
0
14
-10
13
-20
12
-30
11
-130
-140
-150
-160
-40
Start 10 MHz
Stop 100 0 MHz
Start 1 0 MHz
1 dB Comp. (dBm)
Stop 100 0 MHz
-170
Noise Figure (dB)
+29
8
+28
7
+27
6
+26
5
+25
Phase Noise (dBc/Hz)
Reverse Isolation (dB)
-180
- 190
10
1 00
1k
10 k
10 0k
1 M
Typical
4
Start 10 MHz
Stop 10 00 MHz
Start 10 MHz
Input VSWR
2.0
2.0
1.5
1.5
1.0
Stop 100 0 MHz
Output VSWR
Residual Phase Noise Test Conditions:
* Power
Carrier Frequency: 600 MHz
Output: +27.0 dBm
!
!
! Temperature: 25 ºC
! Agilent ES5500 System
1.0
Start 10 MHz
Legend
Sto p 1 000 MH z
+25 ºC
Start 10 MHz
Stop 1000 MHz
+85 ºC - - - - - - -55 ºC
Linear S-Parameters Data
FREQ.
MHz
– – S11– –
Mag Ang
– – S21– –
Mag Ang
– – S12– –
Mag
Ang
– – S22– –
Mag Ang
==================================================================
0.11
10
0.23 151.8
0.11
4.70 -172.3
8.8
-61.9
0.11 -34.4
250
0.14 148.5
0.02
4.66 116.7
-83.6
0.12 -70.5
500
0.14 124.8
0.01 -171.7
4.55
54.5
0.13 -109.3
97.0
750
0.15
0.02 126.7
4.49
-7.5
0.14 -151.2
40.7
1000
0.13
0.05
4.51
15.7
-70.8
0.15
-25.7
1200
0.13
0.12
4.58 -123.8
173.5
-44.2
0.15 155.1
-68.5
1300
0.14
0.16
4.60 -151.8
-70.8
Spectrum Microwave · 2144 Franklin Drive N.E. · Palm Bay, Florida 32905 · PH (888) 553-7531 · Fax (888) 553-7532
Rev.
9/24/09
www.SpectrumMicrowave.com Spectrum Microwave · 2707 Black Lake Place · Philadelphia, Pennsylvania 19154 · PH (215) 464-4000 · Fax (215) 464-4001