FERROXCUBE DATA SHEET E18/4/10/R Planar E cores and accessories Supersedes data of September 2004 2008 Sep 01 Ferroxcube Planar E cores and accessories E18/4/10/R CORES Effective core parameters of an E/PLT combination SYMBOL PARAMETER VALUE UNIT Σ(I/A) core factor (C1) 0.498 mm −1 Ve effective volume 830 mm 3 Ie effective length 20.3 mm Ae effective area 39.5 mm 2 Amin minimum area 35.9 mm 2 m mass of E core half ≈ 2.4 g m mass of plate ≈ 1.7 g 18 ±0.35 14 ±0.3 4 ±0.1 handbook, halfpage 2 ±0.1 Ordering information for plates GRADE 2.5 3.3 ±0.15 4 ±0.1 +0.2 10 ±0.2 0 TYPE NUMBER 3C90 PLT18/10/2/S-3C90 3C92 PLT18/10/2/S-3C92 3C93 PLT18/10/2/S-3C93 3C94 PLT18/10/2/S-3C94 3C95 PLT18/10/2/S-3C95 3C96 PLT18/10/2/S-3C96 3F3 PLT18/10/2/S-3F3 3F35 PLT18/10/2/S-3F35 3F4 PLT18/10/2/S-3F4 3F45 PLT18/10/2/S-3F45 3E6 PLT18/10/2/S-3E6 CBW080 Dimensions in mm. Fig.1 E18/4/10/R core half. 2 ±0.1 18 ±0.35 2.4 ±0.05 dbook, halfpage 10 ±0.2 2.5 +0.2 0 CBW081 Dimensions in mm. Fig.2 PLT 18/10/2. 2008 Sep 01 2 Ferroxcube Planar E cores and accessories E18/4/10/R Core halves for use in combination with a slotted plate (PLT/S) AL measured in combination with a slotted plate (PLT/S) clamping force for AL measurements, 20 ±10 N; measurement coil as for E18/4/10. GRADE 3C90 AL (nH) µe AIR GAP (µm) 100 ±3% ≈ 41 ≈ 870 E18/4/10/R-3C90-A100-P 160 ±3% ≈ 65 ≈ 470 E18/4/10/R-3C90-A160-P 250 ±5% ≈ 102 ≈ 240 E18/4/10/R-3C90-A250-P 315 ±8% ≈ 129 ≈ 170 E18/4/10/R-3C90-A315-P TYPE NUMBER 3680 ±25% ≈ 1500 ≈0 E18/4/10/R-3C90 3C92 2690 ±25% ≈ 1070 ≈0 E18/4/10/R-3C92 3C93 3100 ±25% ≈ 1230 ≈0 3C94 100 ±3% ≈ 41 ≈ 870 E18/4/10/R-3C94-A100-P 160 ±3% ≈ 65 ≈ 470 E18/4/10/R-3C94-A160-P 250 ±5% ≈ 102 ≈ 240 E18/4/10/R-3C94-A250-P 315 ±8% ≈ 129 ≈ 170 E18/4/10/R-3C94-A315-P E18/4/10/R-3C93 3680 ±25% ≈ 1500 ≈0 E18/4/10/R-3C94 3C95 4340 ±25% ≈ 1780 ≈0 E18/4/10/R-3C95 3C96 3250 ±25% ≈ 1320 ≈0 100 ±3% ≈ 41 ≈ 870 E18/4/10/R-3F3-A100-P 160 ±3% ≈ 65 ≈ 470 E18/4/10/R-3F3-A160-P 250 ±5% ≈ 102 ≈ 240 E18/4/10/R-3F3-A250-P 315 ±8% ≈ 129 ≈ 170 E18/4/10/R-3F3-A315-P 3100 ±25% ≈ 1270 ≈0 E18/4/10/R-3F3 2500 ±25% ≈ 1020 ≈0 E18/4/10/R-3F35 3F3 3F35 3F4 E18/4/10/R-3C96 100 ±3% ≈ 41 ≈ 870 E18/4/10/R-3F4-A100-P 160 ±3% ≈ 65 ≈ 470 E18/4/10/R-3F4-A160-P 250 ±5% ≈ 102 ≈ 240 E18/4/10/R-3F4-A250-P 315 ±8% ≈ 129 ≈ 170 E18/4/10/R-3F4-A315-P 1800 ±25% ≈ 740 ≈0 E18/4/10/R-3F4 3F45 1800 ±25% ≈ 740 ≈0 E18/4/10/R-3F45 3E6 15500 +40/−30% ≈ 6400 ≈0 E18/4/10/R-3E6 2008 Sep 01 3 Ferroxcube Planar E cores and accessories E18/4/10/R Properties of core sets under power conditions B (mT) at CORE LOSS (W) at GRADE H = 250 A/m; f = 10 kHz; T = 100 °C f = 100 kHz; ˆ = 100 mT; B T = 100 °C f = 100 kHz; ˆ = 200 mT; B T = 25 °C f = 100 kHz; ˆ = 200 mT; B T = 100 °C f = 400 kHz; ˆ = 50 mT; B T = 100 °C f = 500 kHz; ˆ = 50 mT; B T = 100 °C E18/R+PLT18/S-3C90 ≥320 ≤ 0.095 − − − − E18/R+PLT18/S-3C92 ≥370 ≤ 0.075 − ≤ 0.5 − − E18/R+PLT18/S-3C93 ≥320 ≤ 0.075(1) − ≤ 0.5(1) − − E18/R+PLT18/S-3C94 ≥320 ≤ 0.075 − ≤ 0.5 − − E18/R+PLT18/S-3C95 ≥320 − ≤ 0.46 ≤ 0.43 − − E18/R+PLT18/S-3C96 ≥320 ≤ 0.06 − ≤ 0.4 ≤ 0.15 ≤ 0.3 E18/R+PLT18/S-3F3 ≥300 ≤ 0.09 − − ≤ 0.16 − E18/R+PLT18/S-3F35 ≥300 − − − ≤ 0.08 ≤ 0.12 E18/R+PLT18/S-3F4 ≥250 − − − − − E18/R+PLT18/S-3F45 ≥250 − − − − − 1. Measured at 140 °C. Properties of core sets under power conditions (continued) B (mT) at GRADE H = 250 A/m; f = 10 kHz; T = 100 °C f = 500 kHz; ˆ = 100 mT; B T = 100 °C f = 1 MHz; ˆ = 30 mT; B T = 100 °C f = 1 MHz; ˆ = 50 mT; B T = 100 °C f = 3 MHz; ˆ = 10 mT; B T = 100 °C E18/R+PLT18/S-3C90 ≥320 − − − − E18/R+PLT18/S-3C92 ≥370 − − − − E18/R+PLT18/S-3C93 ≥320 − − − − E18/R+PLT18/S-3C94 ≥320 − − − − E18/R+PLT18/S-3C95 ≥320 − − − − E18/R+PLT18/S-3C96 ≥320 − − − − E18/R+PLT18/S-3F3 ≥300 − − − − E18/R+PLT18/S-3F35 ≥300 ≤ 0.9 − − − E18/R+PLT18/S-3F4 ≥250 − ≤ 0.24 − ≤ 0.39 E18/R+PLT18/S-3F45 ≥250 − ≤ 0.18 ≤ 0.67 ≤ 0.32 2008 Sep 01 4 Ferroxcube Planar E cores and accessories E18/4/10/R MOUNTING PARTS General data and ordering information ITEM Clamp MATERIAL FIGURE stainless steel (CrNi) TYPE NUMBER 3 CLM-E18/PLT18 R 0.8 max. 17.6 7 handbook, halfpage 6.6 ±0.1 lumns 2.2 10.4 min. 0.4 18.2 ±0.3 4.25 min. 2.5 min. CBW176 13.5 max. 18.5 min. CBW552 Dimensions in mm. Fig.4 Fig.3 Clamp for E18/R+PLT18/S. 21.5 min. Recommended PCB cut-out for clamped cores. BLISTER TAPE AND REEL For blister tape dimensions and construction and reel dimensions, see data sheet “E18/4/10”. 2008 Sep 01 5 Ferroxcube Planar E cores and accessories E18/4/10/R DATA SHEET STATUS DEFINITIONS DATA SHEET STATUS PRODUCT STATUS DEFINITIONS Preliminary specification Development This data sheet contains preliminary data. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Product specification Production This data sheet contains final specifications. Ferroxcube reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. DISCLAIMER Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Ferroxcube customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Ferroxcube for any damages resulting from such application. PRODUCT STATUS DEFINITIONS STATUS INDICATION DEFINITION Prototype These are products that have been made as development samples for the purposes of technical evaluation only. The data for these types is provisional and is subject to change. Design-in These products are recommended for new designs. Preferred These products are recommended for use in current designs and are available via our sales channels. Support These products are not recommended for new designs and may not be available through all of our sales channels. Customers are advised to check for availability. 2008 Sep 01 6