CX1V CRYSTAL 10 kHz to 600 kHz Miniature Quartz Crystal for Pierce Oscillators DESCRIPTION The CX1V quartz crystal is a high-quality tuning fork resonator for use in Pierce (single inverter) oscillators. The CX1V is hermetically sealed in a rugged, miniature ceramic package, one-fourth the size of an eight-pin mini-DIP. The CX1V crystal is manufactured using the STATEK-developed photolithographic process, and was designed utilizing the experience acquired by producing millions of crystals for industrial, commercial, military and medical applications. FEATURES actual size side view Glass Lid Shown PACKAGE DIMENSIONS Miniature tuning fork design F E High shock resistance Designed for low power applications Compatible with hybrid or PC board packaging D A Low aging Full military testing available Ideal for battery operated applications Designed and manufactured in the USA B C PACKAGE HANDLING TYP. The CX crystal is hermetically sealed in a ceramic package. Normal handling and soldering precautions for small, low thermal mass parts are adequate when installing or testing CX crystals. CX crystals may be wave soldered, with proper precaution taken to avoid desoldering the leads. A slow machine rate or too high a pre-heat temperature or solder bath temperature can damage the crystals. Lead to package solder interface temperature should not exceed 200oC for RoHS compliant version and 175oC for non-RoHS version, glass lid to package seal rim temperature should not exceed 210oC. If the seal rim reaches temperatures above the maximum specified, the package may lose its hermeticity. Loss of hermeticity results in a frequency decrease and motional resistance increase. MAX. DIM INCHES mm INCHES mm A 0.315 8.00 0.330 8.38 B 0.140 3.56 0.155 3.94 C 0.070 1.78 0.080 2.03 D 0.300 7.62 0.310 7.87 E 0.020 0.51 0.040 1.02 F 0.150 3.81 0.160 4.06 Leads 0.013” x 0.018” (0.33 x 0.46 mm) typical. CONVENTIONAL CMOS PIERCE OSCILLATOR CIRCUIT Rf BUFFER EQUIVALENT CIRCUIT C0 1 L1 C1 AMPLIFIER CS R1 CX1 OSC Freq (fO) Contact factory for design guidelines 2 CG R1 Motional Resistance L1 Motional Inductance C1 Motional Capacitance C0 Shunt Capacitance RA CD 10101 - Rev C STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com SPECIFICATIONS 1. Tighter frequency calibration available. 2. Other turning point available. 3. Higher shock and vibration available. Frequency Capacitance (pF) 100 R1 (kV ) 50 20 10 5 2 Load Range (kHz) 11 10 9 Capacitance (pF) 55-99.9 100-179.9 180-600 8 5 4 250-600 ± 30 ppm ± 50 ppm ±100 ppm ±200 ppm O 170-249.9 HOW TO ORDER CX1V LEADED CRYSTALS “S” if special or custom design. Blank if Std. 600 1.0 10 20 50 100 200 600 300 200 TO ( C) 75-169.9 32.768K, 200 100 50 30 / 10 20 50 100 200 600 Frequency (kHz) FIGURE 4 CX1V TYPICAL TURNING POINT TEMP. (T0) 10-74.9 03 100 Frequency (kHz) Frequency Range (kHz) S 50 Frequency (kHz) 2 0.5 CX1V Standard Calibration Tolerance at 25oC CX1V 20 5 20 10-15.9 16-24.9 25-54.9 10 FIGURE 2 CX1V TYPICAL MOTIONAL CAPACITANCE (C1) (in 1000's) Range (kHz) Load 300 200 FIGURE 3 CX1V TYPICAL QUALITY FACTOR (Q) Load Capacitance (CL), Used to Calibrate CX-1V (other CL available) Frequency FIGURE 1 CX1V TYPICAL MOTIONAL RESISTANCE (R1) C1 (fF) Specifications are typical at 25oC unless otherwise noted. Specifications are subject to change without notice. Frequency Range 10 kHz to 600 kHz Calibration Tolerance1 (see below) Motional Resistance (R1) Figure 1 MAX.: 2x [email protected] kHz 2.5x Typ.@170-600 kHz Motional Capacitance (C1) Figure 2 Quality Factor (Q) Figure 3 Min. is 0.25x Typ. Shunt Capacitance (C0) 2.0 pF MAX. Drive Level 0.5 µW [email protected] kHz 1.0 µW MAX.@ 25-600 kHz 2 Turning Point (TO) Figure 4 Temperature Coefficient (k) -0.035 ppm/0C2 Aging, first year 5ppm MAX. 3 Shock, survival 1,000 G peak 1ms, 1/2 sine Vibration, survival3 20 G RMS 10-2,000 Hz Operating Temperature -10oC to +70oC (Commercial) -40oC to +85oC (Industrial) -55oC to +125oC (Military) Storage Temperature -55oC to +125oC Max Process Temperature 175oC for -03 version 200oC for -05 version I +80 +70 +60 +50 +40 +30 +20 +10 0 -10 -20 10 20 50 100 200 Frequency (kHz) 600 Side Leads Frequency Calibration Operating Temp. Range: Note: Frequency (f) deviation from frequency (fo ) @ turning point Tolerance* C = -10OC to +70OC 03 = Non- K = kHz temperature (T0): f-f O O 2 O 0 @ 25 C I = -40 C to +85 C RoHS = k(T-T0 ) O O (in ppm) M = -55 C to +125 C Compliant f0 S = Customer Specified 05 = RoHS PACKAGING FOR LEADED CRYSTALS Compliant *The above table provides the best calibration tolerance available for each frequency range at 25°C. CX1V - Tray Pack (Standard) STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com 10101 - Rev C