DATA SHEET PD4W09-59LF: 0.81-0.96 GHz Four-Way 0° Power Splitter/Combiner Applications • Cellular radios • Transmitters/receivers Features • Low loss • High isolation • Good I/O match • Excellent phase/amplitude balance • MSOP-8 (8-pin, 3 x 3 mm) package (MSL1, 260 °C per JEDEC J-STD-020) Figure 1. PD4W09-59LF Block Diagram Description The PD4W09-59LF is a monolithic, four-way in-phase hybrid junction tuned for the 0.81 GHz to 0.96 GHz band. The device offers low loss, high isolation, good input/output matching and exceptional phase/amplitude balance. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. Figure 2. PD4W09-59LF Pinout – 8-Pin MSOP-8 (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200245C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 23, 2011 1 DATA SHEET • PD4W09-59LF POWER SPLITTER/COMBINER Table 1. PD4W09-59LF Signal Descriptions Pin # Name Description Pin # Name Description 1 PORT_1 RF port 1 5 PORT_3 RF port 3 2 IN/SUM Common input or summing RF port 6 GND Ground 3 GND Ground 7 GND Ground 4 PORT_4 RF port 4 8 PORT_2 RF port 2 Table 2. PD4W09-59LF Absolute Maximum Ratings (Note 1) Parameter Symbol Input power, CW Minimum PIN Maximum Units 1.500 (Note 2) W 0.375 (Note 3) W Storage temperature TSTG –65 +150 °C Operating temperature TOP –40 +85 °C Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. Note 2: When used as a power divider with a 2.0:1 maximum VSWR on all ports. Note 3: When used as a power combiner with a 2.0:1 maximum VSWR on all ports. CAUTION: Although this device is designed to be as robust as possible, Electrostatic Discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Table 3. PD4W09-59LF Series Electrical Specifications (Note 1) (TOP = +25 °C, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical 0.81 Max Units 0.96 GHz 1.5 dB Frequency range f Insertion loss less6 dB split IL Isolation Iso Input VSWR VSWR IN/SUM port 1.2:1 1.5:1 – Output VSWR VSWR PORT_1, PORT_2, PORT_3, PORT_4 1.2:1 1.5:1 – ±0.4 ±0.6 dB ±6 ±8 deg 1.3 20 Amplitude balance Phase balance 23 dB Note 1: Performance is guaranteed only under the conditions listed in this Table. Electrical and Mechanical Specifications Package Dimensions The absolute maximum ratings of the PD4W09-59LF are provided in Table 2. Electrical specifications are provided in Table 3. The PCB layout footprint for the PD4W09-59LF is provided in Figure 9. Package dimensions for the 8-pin MSOP-8 are shown in Figure 10, and tape and reel dimensions are provided in Figure 11. Typical performance characteristics are shown in Figures 3 through 8. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 May 23, 2011 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 200245C DATA SHEET • PD4W09-59LF POWER SPLITTER/COMBINER Package and Handling Information Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. additional information, refer to the Skyworks Application Note, Solder Reflow Information, document number 200164. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. The PD4W09-59LF is rated to Moisture Sensitivity Level 1 (MSL1) at 260 °C. It can be used for lead or lead-free soldering. For Typical Performance Characteristics (TOP = +25 °C, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) Figure 3. Insertion Loss vs Frequency Figure 4. Output VSWR vs Frequency Figure 5. Isolation vs Frequency Figure 6. Amplitude Balance vs Frequency Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200245C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 23, 2011 3 DATA SHEET • PD4W09-59LF POWER SPLITTER/COMBINER Figure 7. Input VSWR vs Frequency Figure 8. Phase Balance vs Frequency Evaluation Board Description Package and Handling Information The PD4W09-59LF Evaluation Board is used to test the performance of the PD4W09-59LF power splitter/combiner. An assembly drawing for the Evaluation Board is shown in Figure 9. The Evaluation Board layer detail is shown in Figure 10. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. Package Dimensions The PCB layout footprint for the PD4W09-59LF is shown in Figure 11. Typical case markings are shown in Figure 12. Package dimensions for the 8-pin MSOP-8 are shown in Figure 13, and tape and reel dimensions are provided in Figure 14. The PD4W09-59LF is rated to Moisture Sensitivity Level 1 (MSL1) at 260 °C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, Solder Reflow Information, document number 200164. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 May 23, 2011 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 200245C DATA SHEET • PD4W09-59LF POWER SPLITTER/COMBINER Figure 9. PD4W09-59LF Evaluation Board Assembly Drawing Figure 10. PD4W09-59LF Evaluation Board Layer Detail Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200245C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 23, 2011 5 DATA SHEET • PD4W09-59LF POWER SPLITTER/COMBINER Figure 11. PD4W09-59LF PCB Layout Footprint Figure 12. Typical Part Markings Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 May 23, 2011 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 200245C DATA SHEET • PD4W09-59LF POWER SPLITTER/COMBINER Figure 13. PD4W09-59LF 8-Pin MSOP-8 Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200245C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 23, 2011 7 DATA SHEET • PD4W09-59LF POWER SPLITTER/COMBINER Figure 14. MSOP-8 Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 May 23, 2011 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 200245C DATA SHEET • PD4W09-59LF POWER SPLITTER/COMBINER Ordering Information Model Name PD4W09-59LF Power Splitter/Combiner Manufacturing Part Number PD4W09-59LF Evaluation Board Part Number PD4W09-59LF-EVB Copyright © 2012 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200245C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 23, 2011 9