TELEDYNE DEFENCE LIMITED 2.0 to 18.0 GHz IFM Technical Datasheet DR073 A Teledyne Technologies Company Features Full 2.0 – 18GHz broadband operation 15-BIT output (0.5 MHz Resolution) 50 MHz Clocking rate 60 dB Dynamic range SDLVA Log Video output PMOP Detection VME64 Form Factor Applications Product Description Electronic Support Measures Radar Warning Receivers ECM Set-On Airborne, Fixed Wing & Rotary Land Naval Teledyne Defence Limited (TDL) latest digital receiver DR073 builds on the strong tradition of TDL digital frequency discriminators (DFD’s). This new receiver takes key performance elements from existing TDL DFD and successive detection log video amplifier (SDLVA) product lines, integrating them into a complete solution suitable for military environments. The DR073 offers the benefits of TDL’s field-proven proprietary SSS discriminator tiers coupled with the latest digital technology to produce a receiver that provides high accuracy frequency data. In addition, TDL’s latest family of SDLVAs provides high dynamic range, fast recovery time, and excellent linearity across the entire 2-18GHz frequency range. Frequency data is output as a clocked 15 bit Frequency word via the industry standard VME VXS (Multigig RT) backplane connector. Control and status information use serial interfaces on the same VME backplane. Log video is output via a SMC connector on the front panel The DFD is packaged in an industry standard single slot (4HP) width plug-in format suitable for most modern day EW suite equipment racks. Performance in dense signal environments may be enhanced by the addition of TDL’s SA219 Broad Band Switched Multiplexer (BBSwMux), an ultra fast switching (<100ns) channelised ‘Front End’ filter bank, optimized for use with the DR073 For further information, please contact the Sales Dept. Global Defence & Security Solutions DR073 rev 2.0 01 May 2011 Page 1 of 4 © Teledyne Defence Ltd, 2009. All rights reserved. Teledyne Defence Ltd Airedale House Royal London Industrial Estate Acorn Park, Charlestown Shipley, West Yorkshire UK, BD17 7SW Tel: +44 (0) 1274 531 602 Fax:+44 (0) 1274 595 724 Email: [email protected] Web: www.teledynedefence.co.uk TELEDYNE DEFENCE LIMITED 2.0 to 18.0 GHz IFM Technical Datasheet DR073 A Teledyne Technologies Company Electrical Specification Parameters Units Min Nom Max Operating Frequency Range GHz 2.0 18.0 Operating + Guard Band GHz 1.98 18.02 Frequency Resolution MHz 0.5 Digital Frequency resolution Bits 15 Frequency Error (RMS) (+3dB RF SNR) MHz 3.0 Frequency Peak Error MHz 16 Peak Error rate (+3dB RF SNR) % 0.05 PMOP Detection POI % 95 98 Frequency and Amplitude Measurement Dynamic Range dBm -55 +5 Log Video Sensitivity (TSS) dBm -65 Log Video Linearity dB ±2.0 ±2.25 (over frequency and temperature range) Log Video Slope mV/dB 50 Log Video Rise Time ns 20 25 Log Video Recovery Time ns 35 75 RF input pulse width ns 50 CW RF Overload Power dBm 20 RF Input VSWR 2.1:1 Temperature Range °C +10 +60 Supply Current : +12V A 0.1 Supply Current : +3.3V A 2.0 Supply Current : +5V A 2.0 Supply Current : -12V A 0.4 Boot Time sec 5 Data Interfaces RF Input: Front Panel SMA Data Output: VME Backplane VXS Multigig P0 Video Front Panel SMC (75Ohm) Output: Control, VME64x Backplane P1 and P2 Status, Power Data Output Format 15-bit frequency, 2 frequency bad data flags, PMOP detect flag. 50MHz DDR output rate Weight kg 1.75 Size 6U x 4HP 262mm x 20.32mm DR073 rev 2.0 01 May 2011 Page 2 of 4 TELEDYNE DEFENCE LIMITED 2.0 to 18.0 GHz IFM Technical Datasheet DR073 A Teledyne Technologies Company Block Diagram Product Description RF Input is via Front Panel SMA (f) connector Data Output is via VME Backplane as detailed below. Video Output is via Front Panel SMC (m) connector Unit Control and Status is via VME Backplane as detailed below DC Power is via VME Backplane as detailed below Electrical Interface The DR073 utilises the following backplane connectors: Connector Type P1 160 pin DIN (41612, Type C Expanded) 5 rows x 32 pins VME64x 160 pin DIN (41612, Type C Expanded) 5 rows x 32 pins VME64x Multigig RT-2 15x7 way, to VITA 41 P2 P0 DR073 rev 2.0 01 May 2011 Page 3 of 4 DR073 Functionality +5V, +12V and -12V supply and ground. Outer row d required for +3.3V supply +5V supply and ground. Serial Interface and Phase modulation flag. Note: no connections required for outer rows z and d. Frequency data output, IFM system clock input. TELEDYNE DEFENCE LIMITED 2.0 to 18.0 GHz IFM Technical Datasheet DR073 A Teledyne Technologies Company Teledyne Defence Ltd Airedale House Royal London Industrial Estate Acorn Park Charlestown Shipley, West Yorkshire UK, BD17 7SW Tel: +44 (0) 1274 531 602 Fax:+44 (0) 1274 595 724 Email: [email protected] www.teledynedefence.co.uk © Teledyne Defence Ltd, 2009. All rights reserved. Subject to change