2A - SynQor

MQHR-28-12S
Single Output
H igH R eliability DC-DC C onveRteR
16-50V
12V
2A
81% @ 1A / 85% @ 2A
Continuous Input
Transient Input
Output
Output
Efficiency
a
pu d
bl va
ic n
at ce
io d
n
16-40V
F ull P oweR o PeRation : -55ºC
to
+125ºC
The MilQor@ series of high-reliability DC-DC converters
brings SynQor’s field proven high-efficiency synchronous
rectifier technology to the Military/Aerospace industry.
SynQor’s innovative QorSealTM packaging approach ensures
survivability in the most hostile environments. Compatible
N/C
with the industry standard format, these converters operate
at a fixed frequency, have no opto-isolators, and follow
conservative component derating guidelines.
-12S-Y-ES
+VIN
IN RTN
They are
MQHR-28
ut@2A
28Vin 12Vo
CASE
ENA 1
designed and manufactured to comply with a wide range of
SYNC OUT
military standards.
TRIM
+SNS
-SNS
OUT RTN
+VOUT
SYNC IN
Design Process
MQHR series converters are:
• Designed for reliability per NAVSO-P3641-A guidelines
• Designed with components derated per:
— MIL-HDBK-1547A
— NAVSO P-3641A
Qualification Process
MQHR series converters are qualified to:
• MIL-STD-810F
— consistent with RTCA/D0-160E
• SynQor’s First Article Qualification
— consistent with MIL-STD-883F
• SynQor’s Long-Term Storage Survivability Qualification
• SynQor’s on-going life test
In-Line Manufacturing Process
• AS9100 and ISO 9001:2008 certified facility
• Full component traceability
• Temperature cycling
• Constant acceleration
• 24, 96, 160 hour burn-in
• Three level temperature screening
Product# MQHR-28-12S
Phone 1-888-567-9596
DesigneD & ManufactureD in the usa
featuring Qorseal™ hi-rel asseMbly
Features
•
•
•
•
•
•
•
•
Fixed switching frequency
No opto-isolators
Output over-voltage shutdown
Remote sense
Clock synchronization
Primary referenced enable
Continuous short circuit and overload protection
Input under-voltage and over-voltage shutdown
Specification Compliance
MQHR series converters (with MQHE filter) are designed to meet:
• MIL-HDBK-704-8 (A through F)
• RTCA/DO-160 Section 16, 17, 18
• MIL-STD-1275 (B, D) for VIN > 16V
• DEF-STAN 61-5 (part 6)/(5, 6) for VIN > 16V
• MIL-STD-461 (C, D, E, F)
• RTCA/DO-160(E, F, G) Section 22
www.SynQor.com
Doc.# 005-0005334 Rev. 3
08/14/13
Page 1
MQHR-28-12S
Output: 12V
Current: 2A
Technical Specification
BLOCK DIAGRAM
REGULATION STAGE
1
7
POSITIVE
OUTPUT
a
pu d
bl va
ic n
at ce
io d
n
POSITIVE
INPUT
ISOLATION STAGE
CURRENT
SENSE
T1
T2
T1
T2
2
8
INPUT
RETURN
OUTPUT
RETURN
3
CASE
GATE CONTROL
GATE DRIVERS
12
UVLO
OVSD
CURRENT
LIMIT
NO CONNECT
11
4
ENABLE 1
PRIMARY
CONTROL
5
CONTROL POWER
OVP
SECONDARY
CONTROL
MAGNETIC
TRIM
10
+ SENSE
SYNC OUT
9
FEEDBACK
6
− SENSE
SYNC IN
TYPICAL CONNECTION DIAGRAM
28 Vdc
+
open
means
on
Product# MQHR-28-12S
1
+VIN
2
IN RTN
3
CASE
4
ENA 1
5
SYNC OUT
6
SYNC IN
Phone 1-888-567-9596
N/C 12
TRIM 11
MQHR
www.SynQor.com
+SNS 10
-SNS 9
OUT RTN 8
+VOUT 7
Doc.# 005-0005334 Rev. 3
+
Load
08/14/13
Page 2
MQHR-28-12S
Output: 12V
Current: 2A
Technical Specification
MQHR-28-12S ELECTRICAL CHARACTERISTICS
Parameter
Min. Typ. Max. Units Notes & Conditions
Group A
Subgroup
Vin=28V dc ±5%, Iout=2A, CL=0µF, free running
(see Note 9) unless otherwise specified
60
60
-0.8
-1.2
V
V
V
V
500
800
125
135
300
50
V
V
°C
°C
°C
V
(see Note 11)
See Note 1
a
pu d
bl va
ic n
at ce
io d
n
ABSOLUTE MAXIMUM RATINGS
Input Voltage
Non-Operating
Operating
Reverse Bias (Tcase = 125ºC)
Reverse Bias (Tcase = -55ºC)
Isolation Voltage (I/O to case, I to O)
Continuous
Transient (≤100µs)
Operating Case Temperature
Storage Case Temperature
Lead Temperature (20s)
Voltage at ENA1
INPUT CHARACTERISTICS
Operating Input Voltage Range
“
Input Under-Voltage Shutdown
Turn-On Voltage Threshold
Turn-Off Voltage Threshold
Shutdown Voltage Hysteresis
Input Over-Voltage Shutdown
Turn-Off Voltage Threshold
Turn-On Voltage Threshold
Shutdown Voltage Hysteresis
Maximum Input Current
No Load Input Current (operating)
Disabled Input Current
Input Terminal Current Ripple (pk-pk)
OUTPUT CHARACTERISTICS
Output Voltage Set Point (Tcase = 25ºC)
Output Voltage Set Point Over Temperature
Output Voltage Line Regulation
Output Voltage Load Regulation
Total Output Voltage Range
Output Over-Voltage Shutdown
Output Voltage Ripple and Noise Peak to Peak
Operating Output Current Range
Operating Output Power Range
Output DC Current-Limit Inception
Back-Drive Current Limit while Enabled
Back-Drive Current Limit while Disabled
Maximum Output Capacitance
DYNAMIC CHARACTERISTICS
Output Voltage Deviation Load Transient
For a Pos. Step Change in Load Current
For a Neg. Step Change in Load Current
Output Voltage Deviation Line Transient
For a Pos. Step Change in Line Voltage
For a Neg. Step Change in Line Voltage
Turn-On Transient
Output Voltage Rise Time
Output Voltage Overshoot
Turn-On Delay, Rising Vin
Turn-On Delay, Rising ENA
Restart Inhibit Time
Short Circuit Start Time
EFFICIENCY
Iout = 2 A (16 Vin)
Iout = 1 A (16 Vin)
Iout = 2 A (28 Vin)
Iout = 1 A (28 Vin)
Iout = 2 A (40 Vin)
Iout = 1 A (40 Vin)
Iout = 2 A (50 Vin)
Load Fault Power Dissipation
Product# MQHR-28-12S
-500
-800
-55
-65
-1.2
16
16
28
28
40
50
V
V
14.75
14.00
0.65
15.50
14.75
0.80
16.00
15.50
1.05
V
V
V
52.0
50.5
1.0
55.0
53.5
2.0
58.0
56.5
3.0
2
100
15
60
V
V
V
A
mA
mA
mA
12.12
12.19
20
70
12.24
18.9
45
2
24
2.5
50
750
V
V
mV
mV
V
V
mV
A
W
A
A
mA
µF
550
mV
mV
100
100
mV
mV
10
2
8.0
6.0
250
25
ms
%
ms
ms
ms
ms
75
10
40
11.88
11.81
-20
-70
11.76
14.9
0
0
2.1
-550
12.00
12.00
0
0
12.00
16.3
15
2.3
1.2
10
-250
250
-100
-100
15
TBD
TBD
TBD
TBD
TBD
TBD
TBD
6
0
5.5
3.0
180
20
88
85
85
81
82
79
79
2.5
Phone 1-888-567-9596
%
%
%
%
%
%
%
W
HB Grade Products, See Notes 2 & 13
Continuous
Transient, 1s
See Note 3
1, 2, 3
4, 5, 6
1, 2, 3
1, 2, 3
1, 2, 3
See Note 3
1,
1,
1,
1,
1,
1,
1,
Vin = 16V; Iout = 2A
Vin = 16V, 28V, 50V; ENA
Bandwidth = 100kHz – 10MHz; see Figure 14
Vout at sense leads
“
“ ; Vin = 16V, 28V, 40V; Iout=2A
“ ; Vout @ (Iout=0A) - Vout @ (Iout=2A)
“
2,
2,
2,
2,
2,
2,
2,
3
3
3
3
3
3
3
1
2, 3
1, 2, 3
1, 2, 3
1, 2, 3
See Note 5
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
See Note 5
Bandwidth = 10MHz; CL=11µF
See Note 4
See Note 6
Total Iout step = 1A to 2A, 0.2A to 1A; CL=11µF
“
Vin step = 16V to 50V; CL=11µF; see Note 7
4, 5, 6
4, 5, 6
4, 5, 6
4, 5, 6
Vout = 1.2V to 10.8V; Full Resistive Load
Resistive load
ENA = 5V; see Notes 8 & 10
See Note 10
See Note 10
4, 5, 6
See Note 5
4, 5, 6
4, 5, 6
4, 5, 6
4
1,
1,
1,
1,
1,
1,
1,
2,
2,
2,
2,
2,
2,
2,
3
3
3
3
3
3
3
Sustained short circuit on output
www.SynQor.com
Doc.# 005-0005334 Rev. 3
08/14/13
Page 3
MQHR-28-12S
Output: 12V
Current: 2A
Technical Specification
MQHR-28-12S ELECTRICAL CHARACTERISTICS (Continued)
Parameter
Min. Typ. Max. Units Notes & Conditions
Group A
Subgroup
Vin=28V dc ±5%, Iout=2A, CL=0µF, free running
(see Note 9) unless otherwise specified
(see Note 11)
Dielectric strength
500
500
500
100
100
V
V
V
MΩ
MΩ
nF
1
1
1
1
1
1
600
kHz
1, 2, 3
500
2.0
-0.5
20
700
5.5
0.8
80
kHz
V
V
%
1, 2, 3
1, 2, 3
1, 2, 3
See Note 5
20
40
60
mA
%
a
pu d
bl va
ic n
at ce
io d
n
ISOLATION CHARACTERISTICS
Isolation Voltage
Input RTN to Output RTN
Any Input Pin to Case
Any Output Pin to Case
Isolation Resistance (in rtn to out rtn)
Isolation Resistance (any pin to case)
Isolation Capacitance (in rtn to out rtn)
FEATURE CHARACTERISTICS
Switching Frequency (free running)
Synchronization Input
Frequency Range
Logic Level High
Logic Level Low
Duty Cycle
Synchronization Output
Pull Down Current
Duty Cycle
Enable Control (ENA)
Off-State Voltage
Module Off Pulldown Current
On-State Voltage
Module On Pin Leakage Current
Pull-Up Voltage
RELIABILITY CHARACTERISTICS
Calculated MTBF (MIL-STD-217F2)
GB @ Tcase = 70ºC
AIF @ Tcase = 70ºC
WEIGHT CHARACTERISTICS
Device Weight
22
500
550
0.8
80
2
3.2
4.0
20
4.8
V
µA
V
µA
V
4030
338
103 Hrs.
103 Hrs.
45
g
VSYNC OUT = 0.8V
Output connected to SYNC IN of other MQHR unit
Current drain required to ensure module is off
Imax draw from pin allowed with module still on
See Figure A
See Note 5
See Note 5
1, 2, 3
See Note 5
1, 2, 3
See Note 5
1, 2, 3
Electrical Characteristics Notes
1. Converter will undergo input over-voltage shutdown.
2. Derate output power to 50% of rated power at Tcase = 135ºC. 135ºC is above the specified operating range. See Figure 5.
3. High or low state of input voltage must persist for about 200µs to be acted on by the shutdown circuitry.
4. Current limit inception is defined as the point where the output voltage has dropped to 90% of its nominal value.
5. Parameter not tested but guaranteed to the limit specified.
6. Load current transition time ≥ 10µs.
7. Line voltage transition time ≥ 100µs.
8. Input voltage rise time ≤ 250µs.
9. Operating the converter at a synchronization frequency above the free running frequency will cause the converter’s efficiency to be slightly reduced
and it may also cause a slight reduction in the maximum output current/power available. For more information consult the factory.
10. After a disable or fault event, module is inhibited from restarting for 100ms. See Shut Down section of the Control Features description.
11. Only the ES and HB grade products are tested at three temperatures. The C grade products are tested at one temperature. Please refer to the
Construction and Environmental Stress Screening Options table for details.
12. These derating curves apply for the ES and HB grade products. The C grade product has a maximum case temperature of 70ºC.
13. The specified operating case temperature for ES grade products is -45ºC to 100ºC. The specified operating case temperature for C grade products
is 0ºC to 70ºC.
Product# MQHR-28-12S
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-0005334 Rev. 3
08/14/13
Page 4
MQHR-28-12S
Output: 12V
Current: 2A
Technical Figures
100
Data Pending
95
85
a
pu d
bl va
ic n
at ce
io d
n
Efficiency (%)
90
80
75
16 Vin
70
28 Vin
65
40 Vin
60
0.0
0.4
0.8
1.2
1.6
2.0
Load Current (A)
Figure 1: Efficiency at nominal output voltage vs. load current for
minimum, nominal, and maximum input voltage at Tcase=25°C.
Figure 2: Efficiency at nominal output voltage and 60% rated power vs.
case temperature for input voltage of 16V, 28V, and 40V.
12
Data Pending
Power Dissipation (W)
10
8
6
4
16 Vin
28 Vin
2
40 Vin
0
0.0
0.4
0.8
1.2
1.6
2.0
Load Current (A)
2.5
30
2.0
24
1.5
18
1.0
12
Tjmax = 105º C
0.5
Figure 4: Power dissipation at nominal output voltage and 60% rated
power vs. case temperature for input voltage of 16V, 28V, and 40V.
Data Pending
Pout (W)
Iout (A)
Figure 3: Power dissipation at nominal output voltage vs. load current
for minimum, nominal, and maximum input voltage at Tcase=25°C.
6
Tjmax = 125º C
Tjmax = 145º C
0.0
0
25
45
65
85
105
Case Temperature (ºC)
125
145
Figure 5: Output Current / Output Power derating curve as a
function of Tcase and the Maximum desired power MOSFET junction
temperature at Vin = 28V (see Note 12).
Product# MQHR-28-12S
Phone 1-888-567-9596
Figure 6: Output voltage vs. load current showing typical current limit
curves at Vin = 28V.
www.SynQor.com
Doc.# 005-0005334 Rev. 3
08/14/13
Page 5
MQHR-28-12S
Output: 12V
Current: 2A
Application Section
CONTROL FEATURES
The MQHR DC/DC converter uses a two-stage power
conversion topology. The first, or regulation, stage is a
buck-converter that keeps the output voltage constant over
variations in line, load, and temperature. The second, or
isolation, stage uses transformers to provide the functions of
input/output isolation and voltage transformation to achieve
the output voltage required.
ENABLE: The MQHR converter has one enable pin, ENA1
(pin 4), which is referenced with respect to the converter’s
input return (pin 2). It must have a logic high level for the
converter to be enabled; a logic low inhibits the converter.
a
pu d
bl va
ic n
at ce
io d
n
BASIC OPERATION AND FEATURES
Both the regulation and the isolation stages switch at a fixed
frequency for predictable EMI performance. The isolation
stage switches at one half the frequency of the regulation
stage, but due to the push-pull nature of this stage it
creates a ripple at double its switching frequency. As a
result, both the input and the output of the converter have a
fundamental ripple frequency of about 550 kHz in the freerunning mode.
Rectification of the isolation stage’s output is accomplished
with synchronous rectifiers. These devices, which are
MOSFETs with a very low resistance, dissipate far less energy
than would Schottky diodes. This is the primary reason why
the MQHR converters have such high efficiency, particularly
at low output voltages.
Besides improving efficiency, the synchronous rectifiers
permit operation down to zero load current. There is no
longer a need for a minimum load, as is typical for converters
that use diodes for rectification. The synchronous rectifiers
actually permit a negative load current to flow back into the
converter’s output terminals if the load is a source of short
or long term energy. The MQHR converters employ a “backdrive current limit” to keep this negative output terminal
current small.
There is a control circuit in the MQHR converter that
determines the conduction state of the power switches.
It communicates across the isolation barrier through a
magnetically coupled device. No opto-isolators are used.
An input under-voltage shutdown feature with hysteresis is
provided, as well as an input over-voltage shutdown and an
output over-voltage limit. There is also an output current
limit that is nearly constant as the load impedance decreases
(i.e., there is not fold-back or fold-forward characteristic to
the output current under this condition). When a load fault
is removed, the output voltage rises exponentially to its
nominal value without an overshoot. If a load fault pulls the
output voltage below about 60% of nominal, the converter
will shut down to attempt to clear the load fault. After a
short delay it will try to auto-restart.
The MQHR converter’s control circuit does not implement an
over-temperature shutdown.
The following sections describe the use and operation of
additional control features provided by the MQHR converter.
Product# MQHR-28-12S
Phone 1-888-567-9596
The enable pin is internally pulled high so that an open
connection will enable the converter. Figure A shows the
equivalent circuit looking into the enable pin. It is TTL
compatible and has hysteresis.
5V
82.5K
PIN4
PIN2
ENA1
10K
TO ENABLE
CIRCUITRY
IN RTN
Figure A: Circuit diagram shown for reference only, actual circuit
components may differ from values shown for equivalent circuit.
SHUT DOWN: The MQHR converter will shut down in
response to only five conditions: ENA input low, VIN input
below under-voltage shutdown threshold, VIN input above
over-voltage shutdown threshold, output voltage below the
output under-voltage threshold, and output voltage above
the output over-voltage threshold. Following any shutdown
event, there is a startup inhibit delay which will prevent the
converter from restarting for approximately 100ms. After
the 100ms delay elapses, if the enable inputs are high and
the input voltage is within the operating range, the converter
will restart. If the VIN input is brought down to nearly 0V
and back into the operating range, there is no startup inhibit,
and the output voltage will rise according to the “Turn-On
Delay, Rising Vin” specification.
REMOTE SENSE: The purpose of the remote sense pins
is to correct for the voltage drop along the conductors that
connect the converter’s output to the load. To achieve
this goal, a separate conductor should be used to connect
the +SENSE pin (pin 10) directly to the positive terminal
of the load, as shown in the connection diagram on Page
2. Similarly, the –SENSE pin (pin 9) should be connected
through a separate conductor to the return terminal of the
load.
NOTE: Even if remote sensing of the load voltage is not
desired, the +SENSE and the -SENSE pins must be connected
to +Vout (pin 7) and OUTPUT RETURN (pin 8), respectively,
to get proper regulation of the converter’s output. If they
are left open, the converter will have an output voltage that
is approximately 200mV higher than its specified value.
www.SynQor.com
Doc.# 005-0005334 Rev. 3
08/14/13
Page 6
MQHR-28-12S
Output: 12V
Current: 2A
Application Section
Inside the converter, +SENSE is connected to +Vout with a
100Ω resistor and –SENSE is connected to OUTPUT RETURN
with a 10Ω resistor.
5V
a
pu d
bl va
ic n
at ce
io d
n
It is also important to note that when remote sense is used,
the voltage across the converter’s output terminals (pins 7
and 8) will be higher than the converter’s nominal output
voltage due to resistive drops along the connecting wires.
This higher voltage at the terminals produces a greater
voltage stress on the converter’s internal components and
may cause the converter to fail to deliver the desired output
voltage at the low end of the input voltage range at the
higher end of the load current and temperature range.
Please consult the factory for details.
Figure B shows the equivalent circuit looking into the SYNC
IN pin and Figure C shows the equivalent circuit looking into
the SYNC OUT pin.
SYNCHRONIZATION: The MQHR converter’s switching
frequency can be synchronized to an external frequency
source that is in the 500 kHz to 700 kHz range. A pulse
train at the desired frequency should be applied to the SYNC
IN pin (pin 6) with respect to the INPUT RETURN (pin 2).
This pulse train should have a duty cycle in the 20% to 80%
range. Its low value should be below 0.8V to be guaranteed
to be interpreted as a logic low, and its high value should
be above 2.0V to be guaranteed to be interpreted as a logic
high. The transition time between the two states should be
less than 300ns.
If the MQHR converter is not to be synchronized, the SYNC
IN pin should be left open circuit. The converter will
then operate in its free-running mode at a frequency of
approximately 550 kHz.
If, due to a fault, the SYNC IN pin is held in either a logic low
or logic high state continuously, or the SYNC IN frequency
is outside the 500-700 kHz range, the MQHR converter will
revert to its free-running frequency.
The MQHR converter also has a SYNC OUT pin (pin 5). This
output can be used to drive the SYNC IN pins of as many as
ten (10) other MQHR converters. The pulse train coming out
of SYNC OUT has a duty cycle of 50% and a frequency that
matches the switching frequency of the converter with which
it is associated. This frequency is either the free-running
frequency if there is no valid synchronization signal at the
SYNC IN pin, or the synchronization frequency if there is.
The synchronization feature is entirely compatible with that
of SynQor’s MQFL family of converters.
5V
5K
PIN 6
PIN 2
SYNC IN
5K
TO SYNC
CIRCUITRY
SYNC OUT
FROM SYNC
CIRCUITRY
IN RTN
OPEN COLLECTOR
OUTPUT
PIN 5
PIN 2
Figure C: Equivalent circuit looking into SYNC OUT pin with
respect to the IN RTN (input return) pin.
OUTPUT VOLTAGE TRIM: the TRIM pin (pin 11) can
adjust the MQHR converter’s output voltage ±10% around
its nominal value.
To trim the output voltage above its nominal value, connect
an external resistor from the TRIM pin to the –SENSE pin
as shown in Figure D. The value of this trim up resistor
should be chosen according to the following equation or
from Figure E:
Rtrim up(Ω) = 7900Ω*Vnom
Vout - Vnom - 39600Ω
where:
Vnom = the converter’s nominal output voltage,
Vout = the desired output voltage (greater than
Vnom), and
Rtrim up is in Ohms.
As the output voltage is trimmed up, it produces a greater
voltage stress on the converter’s internal components
and may cause the converter to fail to deliver the
desired output voltage at the low end of the input
voltage range at the higher end of the load current and
temperature range. Please consult the factory for details.
To trim the output voltage below its nominal value, connect
an external resistor (Rtrim down) between the TRIM pin
and the +SENSE pin, and another resistor (Rtrim sense)
connected between the TRIM pin and the -SENSE pin as
shown in Figure D. The values of these trim down resistors
should be chosen according to the following equation or
from Figure E:
Rtrim down(Ω) = 38100Ω*Vout - 20900Ω*Vnom
- 104500Ω
Vnom - Vout
Rtrim sense(Ω) = 0.61 * Rtrim down(Ω)
where:
IN RTN
Figure B: Equivalent circuit looking into the SYNC IN pin with
respect to the IN RTN (input return) pin.
Product# MQHR-28-12S
5K
Phone 1-888-567-9596
Vnom = the converter’s nominal output voltage,
Vout = the desired output voltage (less than Vnom),
and
Rtrim down and Rtrim sense are in Ohms.
Factory trimmed converters are available by request.
www.SynQor.com
Doc.# 005-0005334 Rev. 3
08/14/13
Page 7
MQHR-28-12S
Output: 12V
Current: 2A
Application Section
shutdown threshold does not change with output trim or
sense drops; excessive trim-up or output wiring drops may
cause an output over-voltage shutdown event. After a
startup inhibit delay, the converter will attempt to restart.
Trim Up
Trim Down
Trim Sense
OUTPUT UNDER-VOLTAGE SHUTDOWN: The MQHR
converter will also shut down if the voltage at its power
output pins ever dips below 60% of the nominal value for
more than a few milliseconds. Output voltage reduction
due to output current overload (current limit) is the most
common trigger for this shutdown. The shutdown threshold
does not change with output trim but at only 10%, trimdown should not trigger this event. After a startup inhibit
delay, the converter will attempt to restart. This shutdown
is disabled during startup.
1000
a
pu d
bl va
ic n
at ce
io d
n
External Trim Resistance (kOhms)
10000
100
10
-10%
-8%
-6%
-4%
-2%
0%
2%
4%
6%
8%
10%
Output Voltage Adjustment
Figure E: Trim up and Trim down as a function of external trim resistance.
INPUT UNDER-VOLTAGE SHUTDOWN: The MQHR
converter has an under-voltage shutdown feature that
ensures the converter will be off if the input voltage is too
low. The input voltage turn-on threshold is higher than
the turn-off threshold. In addition, the MQHR converter
will not respond to a state of the input voltage unless it
has remained in that state for more than about 200µs. This
hysteresis and the delay ensure proper operation when the
source impedance is high or in a noisy environment.
INPUT OVER-VOLTAGE SHUTDOWN: The MQHR
converter also has an over-voltage feature that ensures the
converter will be off if the input voltage is too high. It also
has a hysteresis and time delay to ensure proper operation.
OUTPUT OVER-VOLTAGE SHUTDOWN: The MQHR
converter will shut down if the voltage at its power output
pins ever exceeds about 130% of the nominal value. The
28 Vdc
+
_
open
means
on
BACK-DRIVE CURRENT LIMIT: Converters that use
MOSFETs as synchronous rectifiers are capable of drawing
a negative current from the load if the load is a source of
short- or long-term energy. This negative current is referred
to as a “back-drive current”.
Conditions where back-drive current might occur include
paralleled converters that do not employ current sharing.
It can also occur when converters having different output
voltages are connected together through either explicit or
parasitic diodes that, while normally off, become conductive
during startup or shutdown. Finally, some loads, such as
motors, can return energy to their power rail. Even a load
capacitor is a source of back-drive energy for some period of
time during a shutdown transient.
To avoid any problems that might arise due to back-drive
current, the MQHR converters limit the negative current
that the converter can draw from its output terminals. The
threshold for this back-drive current limit is placed sufficiently
below zero so that the converter may operate properly
down to zero load, but its absolute value (see the Electrical
Characteristics page) is small compared to the converter’s
rated output current.
1 +VIN
2 IN RTN
N/C 12
TRIM 11
3 CASE
4 ENA 1
+SNS 10
-SNS 9
MQHL
MQHR
5 SYNC OUT
6 SYNC IN
R TRIM DOWN
RTRIM UP / R TRIM SENSE
OUT RTN 8
+VOUT 7
+
Load
_
Figure D: Typical connection for output voltage trimming.
Product# MQHR-28-12S
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-0005334 Rev. 3
08/14/13
Page 8
MQHR-28-12S
Output: 12V
Current: 2A
Application Section
When the converter is mounted on a metal plate, the plate
will help to make the converter’s case bottom a uniform
temperature. How well it does so depends on the thickness
of the plate and on the thermal conductance of the interface
layer (e.g. thermal grease, thermal pad, etc.) between
the case and the plate. Unless this is done very well, it
is important not to mistake the plate’s temperature for the
maximum case temperature. It is easy for them to be as much
as 5-10ºC different at full power and at high temperatures.
It is suggested that a thermocouple be attached directly to
the converter’s case through a small hole in the plate when
investigating how hot the converter is getting. Care must
also be made to ensure that there is not a large thermal
resistance between the thermocouple and the case due to
whatever adhesive might be used to hold the thermocouple
in place.
a
pu d
bl va
ic n
at ce
io d
n
CURRENT LIMIT: In the event of excess load, the MQHR
converter will quickly reduce its output voltage to keep
the load current within safe limits (see Figure 6). If the
overload persists for more than 14 milliseconds, the converter
will shut off, wait a restart delay, and then automatically
attempt to re-start. The timeout is internally implemented
with an integrator: counting up whenever current limit is
active, and counting down at 1/5th the rate whenever current
limit becomes inactive. In this way a series of short-duration
overloads will not cause the converter to shut down, while it
will shut down in response to sustained overloads.
THERMAL CONSIDERATIONS: Figure 5 shows the suggested
Power Derating Curves for this converter as a function of the case
temperature and the maximum desired power MOSFET junction
temperature. All other components within the converter are cooler
than its hottest MOSFET, which at full power is no more than 20ºC
higher than the case temperature directly below this MOSFET.
The Mil-HDBK-1547A component derating guideline calls
for a maximum component temperature of 105ºC. Figure 5
therefore has one power derating curve that ensures this limit
is maintained. It has been SynQor’s extensive experience that
reliable long-term converter operation can be achieved with
a maximum component temperature of 125ºC. In extreme
cases, a maximum temperature of 145ºC is permissible, but not
recommended for long-term operation where high reliability is
required. Derating curves for these higher temperature limits
are also included in Figure 5. The maximum case temperature
at which the converter should be operated is 135ºC.
Product# MQHR-28-12S
Phone 1-888-567-9596
INPUT SYSTEM INSTABILITY: This condition can occur
because any dc-dc converter appears incrementally as a
negative resistance load. A detailed application note titled
“Input System Instability” is available on the SynQor website
which provides an understanding of why this instability
arises, and shows the preferred solution for correcting it.
www.SynQor.com
Doc.# 005-0005334 Rev. 3
08/14/13
Page 9
MQHR-28-12S
Output: 12V
Current: 2A
Stress Screening
CONSTRUCTION AND ENVIRONMENTAL STRESS SCREENING OPTIONS
Consistent with
MIL-STD-883F
(
ES-Grade
specified from
0 ºC to +70 ºC
) (
specified from
-45 ºC to +100 ºC
HB-Grade
) (
specified from
-55 ºC to +125 ºC
)
a
pu d
bl va
ic n
at ce
io d
n
Screening
C-Grade
Element Evaluation
Internal Visual
*
No
Yes
Yes
Yes
Yes
Yes
Temperature Cycle
Method 1010
No
Condition B
(-55 ºC to +125 ºC)
Condition C
(-65 ºC to +150 ºC)
Constant Acceleration
Method 2001
(Y1 Direction)
No
500g
Condition A
(5000g)
Burn-in
Method 1015
24 Hrs @ +125 ºC
96 Hrs @ +125 ºC
160 Hrs @ +125 ºC
+25 ºC
-45, +25, +100 ºC
-55, +25, +125 ºC
Full QorSeal
Full QorSeal
Full QorSeal
*
Yes
Yes
QorSeal
QorSeal
QorSeal
Final Electrical Test
Method 5005 (Group A)
Mechanical Seal,
Thermal, and
Coating Process
External Visual
2009
Construction Process
* Per IPC-A-610 Class 3
MilQor converters and filters are offered in three variations of environmental stress screening options. All MilQor converters use SynQor’s proprietary
QorSeal™ Hi-Rel assembly process that includes a Parylene-C coating of the circuit, a high performance thermal compound filler, and a nickel barrier
gold plated aluminum case. Each successively higher grade has more stringent mechanical and electrical testing, as well as a longer burn-in cycle. The ESand HB-Grades are also constructed of components that have been procured through an element evaluation process that pre-qualifies each new batch of
devices.
Product# MQHR-28-12S
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-0005334 Rev. 3
08/14/13
Page 10
MQHR-28-12S
Output: 12V
Current: 2A
a
pu d
bl va
ic n
at ce
io d
n
Mechanical Diagrams
MQHR-28-12S-U-ES
PIN DESIGNATIONS
DC-DC ConvERtER
28vin 12vout @ 2A
Pin # Function
1
2
3
4
5
6
7
8
9
10
11
12
Case U
Positive input
Input return
Case
Enable 1
Sync output
Sync input
Positive output
Output return
- Sense
+ Sense
Trim
No connection
NOTES
1)
Case: Aluminum with gold over
nickel plate finish for the C,
ES, and HB Grade products.
2)
Pins:
3)
Diameter: 0.040’’ (1.02mm)
Material: Copper
Finish: Copper alloy with Gold
over Nickel plating, followed
by Sn/Pb solder dip
All dimensions in inches (mm)
4)
Tolerances:
5)
Weight: 1.6 oz (45.4 g) typical
6)
Workmanship: Meets or exceeds
IPC-A-610 Class III
7)
Pin 1 identification hole, not intended
for mounting
8)
Baseplate flatness tolerance is 0.004”
(.10mm) TIR for surface
MQHR-28-12S-W-ES
DC-DC ConvERtER
28vin 12vout @ 2A
Case W
Product# MQHR-28-12S
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-0005334 Rev. 3
a) x.xx +/-0.02 in.
(x.x +/-0.5mm)
b) x.xxx +/-0.010 in.
(x.xx +/-0.25mm)
08/14/13
Page 11
MQHR-28-12S
Output: 12V
Current: 2A
a
pu d
bl va
ic n
at ce
io d
n
Mechanical Diagrams
MQHR-28-12S-X-ES
PIN DESIGNATIONS
DC-DC ConvERtER
28vin 12vout @ 2A
Pin # Function
1
2
3
4
5
6
7
8
9
10
11
12
Case X
Positive input
Input return
Case
Enable 1
Sync output
Sync input
Positive output
Output return
- Sense
+ Sense
Trim
No connection
NOTES
1)
Case: Aluminum with gold over
nickel plate finish for the C,
ES, and HB Grade products.
2)
Pins:
MQHR-28-12S-Y-ES
DC-DC ConvERtER
28vin 12vout @ 2A
3)
4)
5)
Weight: 1.6 oz (45.4 g) typical
6)
Workmanship: Meets or exceeds
IPC-A-610 Class III
Pin 1 identification hole, not intended
for mounting
Baseplate flatness tolerance is 0.004”
(.10mm) TIR for surface
7)
Case Y
Product# MQHR-28-12S
Phone 1-888-567-9596
www.SynQor.com
Diameter: 0.040’’ (1.02mm)
Material: Copper
Finish: Copper alloy with Gold
over Nickel plating, followed
by Sn/Pb solder dip
All dimensions in inches (mm)
Tolerances: a) x.xx +/-0.02 in.
(x.x +/-0.5mm)
b) x.xxx +/-0.010 in.
(x.xx +/-0.25mm)
8)
Doc.# 005-0005334 Rev. 3
08/14/13
Page 12
MQHR-28-12S
Output: 12V
Current: 2A
a
pu d
bl va
ic n
at ce
io d
n
Mechanical Diagrams
PIN DESIGNATIONS
MQHR-28-12S-Z-ES
DC-DC ConvERtER
28vin 12vout @ 2A
Pin # Function
1
2
3
4
5
6
7
8
9
10
11
12
Case Z
Positive input
Input return
Case
Enable 1
Sync output
Sync input
Positive output
Output return
- Sense
+ Sense
Trim
No connection
NOTES
1)
Case: Aluminum with gold over
nickel plate finish for the C,
ES, and HB Grade products.
2)
Pins:
3)
4)
5)
Weight: 1.6 oz (45.4 g) typical
6)
Workmanship: Meets or exceeds
IPC-A-610 Class III
Pin 1 identification hole, not intended
for mounting
Baseplate flatness tolerance is 0.004”
(.10mm) TIR for surface
7)
8)
Product# MQHR-28-12S
Phone 1-888-567-9596
www.SynQor.com
Diameter: 0.040’’ (1.02mm)
Material: Copper
Finish: Copper alloy with Gold
over Nickel plating, followed
by Sn/Pb solder dip
All dimensions in inches (mm)
Tolerances: a) x.xx +/-0.02 in.
(x.x +/-0.5mm)
b) x.xxx +/-0.010 in.
(x.xx +/-0.25mm)
Doc.# 005-0005334 Rev. 3
08/14/13
Page 13
MQHR-28-12S
Output: 12V
Current: 2A
Ordering Information
MilQor Converter FAMILY MATRIX
a
pu d
bl va
ic n
at ce
io d
n
The tables below show the array of MilQor converters available. When ordering SynQor converters, please ensure that
you use the complete part number according to the table in the last page. Contact the factory for other requirements.
Single Output
Full Size
MQFL-28
16-40Vin Cont.
16-50Vin 1s Trans.*
Dual Output †
1.5V
(1R5S)
1.8V
(1R8S)
2.5V
(2R5S)
3.3V
(3R3S)
5V
(05S)
6V
(06S)
7.5V
(7R5S)
9V
(09S)
12V
(12S)
15V
(15S)
28V
(28S)
5V
(05D)
12V
(12D)
15V
(15D)
40A
40A
40A
30A
24A
20A
16A
13A
10A
8A
4A
24A
Total
10A
Total
8A
Total
40A
40A
40A
30A
24A
20A
16A
13A
10A
8A
4A
24A
Total
10A
Total
8A
Total
40A
40A
40A
30A
20A
17A
13A
11A
8A
6.5A
3.3A
40A
40A
40A
30A
20A
17A
13A
11A
8A
6.5A
3.3A
40A
40A
40A
30A
24A
20A
16A
13A
10A
8A
4A
24A
Total
10A
Total
8A
Total
40A
40A
30A
22A
15A
12A
10A
8A
6A
5A
2.7A
15A
Total
6A
Total
5A
Total
Absolute Max Vin = 60V
MQFL-28E
16-70Vin Cont.
16-80Vin 1s Trans.*
Absolute Max Vin =100V
MQFL-28V
16-40Vin Cont.
5.5-50Vin 1s Trans.*
Absolute Max Vin = 60V
MQFL-28VE
16-70Vin Cont.
5.5-80Vin 1s Trans.*
Absolute Max Vin = 100V
MQFL-270
155-400Vin Cont.
155-475Vin 1s Trans.*
Absolute Max Vin = 550V
MQFL-270L
65-350Vin Cont.
65-475Vin 1s Trans.*
Absolute Max Vin = 550V
Single Output
Half Size
MQHL-28
16-40Vin Cont.
16-50Vin 1s Trans.*
Dual Output †
1.5V
(1R5S)
1.8V
(1R8S)
2.5V
(2R5S)
3.3V
(3R3S)
5V
(05S)
6V
(06S)
7.5V
(7R5S)
9V
(09S)
12V
(12S)
15V
(15S)
28V
(28S)
5V
(05D)
12V
(12D)
15V
(15D)
20A
20A
20A
15A
10A
8A
6.6A
5.5A
4A
3.3A
1.8A
10A
Total
4A
Total
3.3A
Total
20A
20A
20A
15A
10A
8A
6.6A
5.5A
4A
3.3A
1.8A
10A
Total
4A
Total
3.3A
Total
10A
10A
10A
7.5A
5A
4A
3.3A
2.75A
2A
1.65A
0.9A
5A
Total
2A
Total
1.65A
Total
10A
10A
10A
7.5A
5A
4A
3.3A
2.75A
2A
1.65A
0.9A
5A
Total
2A
Total
1.65A
Total
Absolute Max Vin = 60V
MQHL-28E
16-70Vin Cont.
16-80Vin 1s Trans.*
Absolute Max Vin =100V
MQHR-28
16-40Vin Cont.
16-50Vin 1s Trans.*
Absolute Max Vin = 60V
MQHR-28E
16-70Vin Cont.
16-80Vin 1s Trans.*
Absolute Max Vin = 100V
Check with factory for availability.
†80% of total output current available on any one output.
*Converters may be operated at the highest transient input voltage, but some component electrical and thermal stresses would be beyond MILHDBK-1547A guidelines.
Product# MQHR-28-12S
Phone 1-888-567-9596
www.SynQor.com
Doc.# 005-0005334 Rev. 3
08/14/13
Page 14
MQHR-28-12S
Output: 12V
Current: 2A
Ordering Information
PART NUMBERING SYSTEM
The part numbering system for SynQor’s MilQor DC-DC converters follows the format shown in the table below.
Not all combinations make valid part numbers, please contact SynQor for availability. See the Product Summary web page for more options.
MQHR-28-12S-Y-ES
a
pu d
bl va
ic n
at ce
io d
n
Example:
Input
Voltage
Range
Model
Name
28
28E
28V
28VE
MQFL
MQHL
MQHR
270
270L
Output Voltage(s)
Single
Output
Dual
Output
1R5S
1R8S
2R5S
3R3S
05S
06S
7R5S
09S
12S
15S
28S
05D
12D
15D
Package Outline/
Pin Configuration
Screening
Grade
U
X
Y
W
Z
C
ES
HB
APPLICATION NOTES
A variety of application notes and technical white papers can be downloaded in pdf format from the SynQor website.
PATENTS
SynQor holds the following U.S. patents, one or more of which apply to each product listed in this document. Additional patent applications may be
pending or filed in the future.
5,999,417
6,222,742
6,545,890
6,577,109
6,594,159
6,731,520
6,894,468
6,896,526
6,927,987
7,050,309
7,072,190
7,085,146
7,119,524
7,269,034
7,272,021
7,272,023
7,558,083
7,564,702
7,765,687
7,787,261
8,023,290
8,149,597
Contact SynQor for further information and to order:
Warranty
Phone:
Toll Free:
Fax:
E-mail:
Web:
Address:
SynQor offers a two (2) year limited warranty. Complete warranty information is listed on our website or is available upon request from SynQor.
Product# MQHR-28-12S
978-849-0600
1-888-567-9596
978-849-0602
[email protected]
www.synqor.com
155 Swanson Road
Boxborough, MA 01719
USA
Phone 1-888-567-9596
Information furnished by SynQor is believed to be accurate and reliable.
However, no responsibility is assumed by SynQor for its use, nor for any
infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any
patent or patent rights of SynQor.
www.SynQor.com
Doc.# 005-0005334 Rev. 3
08/14/13
Page 15