LC01-6 Low Capacitance TVS for High-Speed Telecommunication Systems PROTECTION PRODUCTS Description Features 1500 watts peak pulse power (tp = 10/1000µs) Transient protection for high speed data lines to The LC01-6 transient voltage suppressor is designed to protect components which are connected to high speed telecommunication lines from voltage surges caused by lightning, electrostatic discharge (ESD), and electrical fast transients (EFT). TVS diodes are ideal for use as board level protection of sensitive semiconductor components. The LC01-6 is designed for metallic mode, secondary line side protection in digital line card applications. It features solid-state silicon-avalanche technology for unmatched transient protection without device degradation. The LC01-6 combines TVS diodes with low capacitance compensation diodes to provide an integrated, low capacitance protection solution. Additional features include sub-nanosecond response time, a low operating voltage of 6 volts, and low clamping voltage. IEC 61000-4-2 (ESD), ±15kV (air), ±8kV (contact) IEC 61000-4-4 (EFT), 40A (5/50ns) IEC 61000-4-5 (Lightning), 95A (8/20µs) Bellcore 1089 (Outer-Building), 100A (10/1000µs), 500A (2/10µs) FCC Part 68, 200A (10/160µs) ITU K.21, 100A (5/310µs) ITU K.20, 200A (5/310µs) Differential protection for one Tip and Ring line pair Low capacitance for high speed interfaces Low operating and clamping voltage Integrated structure saves board space and increases reliability Solid-state silicon-avalanche technology Mechanical Characteristics The LC01-6 is suitable for use on T1/E1 and xDSL interfaces in equipment such as base stations, routers, and channel service units. The LC01-6 meets the longhaul (outer-building) transient immunity requirements of Bellcore 1089, FCC Part 68 (Type A and B surges), ITU K.20 and K.21, and IEC 61000-4-5. JEDEC SO-16W package UL 497B listed Molding compound flammability rating: UL 94V-0 Marking : Part number, date code, logo Packaging : Tube or Tape and Reel per EIA 481 Applications Circuit Diagram T1/E1 Line Cards Base Stations WAN Interfaces xDSL Interfaces CSU/DSU Equipment Schematic & PIN Configuration SO-16W (Top View) Revision 12/09/04 1 www.semtech.com LC01-6 PROTECTION PRODUCTS Absolute Maximum Rating R ating Symbol Value Units Peak Pulse Power (tp = 10/1000µs) Pp k 1500 Watts Peak Pulse Current (tp = 10/1000µs) IP P 100 A Peak Pulse Current (tp = 10/160µs) IP P 200 A Thermal Resistance Junction to Case θJ C 30 °C/W Thermal Resistance Junction to Ambient θJ A 95 °C/W Lead Soldering Temperature TL 260 (10 sec.) °C Operating Temperature TJ -55 to +125 °C TSTG -55 to +150 °C Storage Temperature Electrical Characteristics LC01-6 Parameter Symbol Conditions Minimum Typical Maximum Units 6 V Reverse Stand-Off Voltage VRWM Reverse Breakdown Voltage V BR It = 1mA Reverse Leakage Current IR VRWM = 6V, T=25°C 25 µA Clamp ing Voltage VC IPP = 100A tp = 10/1000µs 15 V Clamp ing Voltage VC IPP = 200A tp = 10/160µs 16 V Temp erature Coefficient of Breakdown Voltage Junction Cap acitance 2004 Semtech Corp. αTVBR Cj 8 V 3 VR = 0V, f = 1MHz 2 mV/°C 50 pF www.semtech.com LC01-6 PROTECTION PRODUCTS Typical Characteristics Non-Repetitive Peak Pulse Power vs. Pulse Time Power Derating Curve 100 110 90 % of Rated Power or IPP Peak Pulse Power - Ppk (kW) 100 10 80 70 60 50 40 30 20 10 1 0 0.1 1 10 100 1000 0 25 50 Pulse Duration - tp (µs) Pulse Waveform 80 e -t 60 50 td = I PP /2 30 20 175 10 8 6 Waveform Parameters: tr = 10µs td = 1000µs 4 2 10 0 0 0 10 1000 0 3000 10 20 30 40 50 60 70 80 90 100 110 Peak Pulse Current - IPP (A) T im e (µs) Capacitance vs. Reverse Voltage AC Power Dissipation 41.5 6 Pins 1-8 tied together Pins 9 - 16 tied together f = 1MHz 41 5 40.5 4 Power (w) Capacitance - Cj (pF) 150 12 Clamping Voltage - VC (V) 90 Percent of IPP 125 14 W aveform Parameters: tr = 10µs td = 1000µs 100 40 100 Clamping Voltage vs. Peak Pulse Current 110 70 75 Ambient Temperature - TA (oC) 40 3 39.5 2 39 1 38.5 0 0 1 2 3 4 5 6 1 Reverse Voltage - VR (V) 2004 Semtech Corp. 10 100 1000 Time (s) 3 www.semtech.com LC01-6 PROTECTION PRODUCTS Applications Information Device Connection Options for Protection of HighSpeed Data Lines The LC01-6 is designed to protect high-speed data lines from transient over-voltages which result from lightning and ESD. The device is designed to protect one line pair in differential (Line-to-Line) mode. Pins 18 are connected to line 1 and pins 9-16 are connected to line 2 as shown. All pins should be connected for best results. T1/E1 Linecard Protection A typical long-haul T1/E1 linecard protection circuit is shown below. The LC01-6 is connected between Tip and Ring on the transmit and receive line pairs. It provides protection to metallic (line-to-line) lightning surges per Bellcore 1089 and FCC Part 68. Depending on the application, a high voltage crowbar device (not shown) such as a gas discharge tube (GDT) or TVS Thyristor may be used to suppress common mode (lineto-ground) surges. To complete the protection circuit, the SRDA05-4 (or SRDA3.3-4 for 3.3V supplies) is employed as the secondary IC side protection element. This device helps prevent the transceiver from latching up by providing fine clamping of transients that are coupled through the transformer. Positive temperature coefficient (PTC) resistors or fuses are also required for AC power cross protection. For further information, reference Semtech application note AN97-10. Figure 1 - Schematic and Pin Configuration Figure 2 - Connection for Differential Protection (Line-to-Line) 2004 Semtech Corp. 4 www.semtech.com LC01-6 PROTECTION PRODUCTS Typical Applications T1/E1 Line Card Protection (Long-Haul Applications) SDSL Protection 2004 Semtech Corp. 5 www.semtech.com LC01-6 PROTECTION PRODUCTS Outline Drawing - SO-16W A D e N DIM A A1 A2 b c D E1 E e h J L L1 N R 01 aaa bbb ccc E/2 E1 E R ccc C 1 2 3 e/2 B DIMENSIONS INCHES MILLIMETERS MIN NOM MAX MIN NOM MAX 2.65 .104 2.35 0.30 .012 0.10 2.55 .100 2.05 .020 0.31 0.51 0.33 .013 0.20 .401 .405 10.10 10.20 10.30 .295 .299 7.40 7.50 7.60 .405 10.30 BSC .050 BSC 1.27 BSC (.020) (0.51) (.025) (0.63) .015 .033 .050 0.40 0.83 1.27 (.055) (1.40) 16 16 (.030) (0.76) 8° 0° 8° 0° .004 0.10 .010 0.25 .013 0.33 .092 .003 .080 .012 .007 .397 .291 D aaa C A2 A SEATING PLANE H A1 C bxN bbb C A-B D c GAGE PLANE h x 45° 0.25 L SEE DETAIL SIDE VIEW 01 (L1) J DETAIL A A NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. DATUMS -A- AND -B- TO BE DETERMINED AT DATUM PLANE -H- 3. DIMENSIONS "E1" AND "D" DO NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. 4. REFERENCE JEDEC STD MS-013, VARIATION AA. Land Pattern - SO-16W D DIM Z C C D E G X Y Z G Y E 2004 Semtech Corp. DIMENSIONS INCHES MILLIMETERS (.362) .350 .050 .275 .023 .086 .448 (9.20) 8.89 1.27 7.00 0.60 2.20 11.40 X 6 www.semtech.com LC01-6 PROTECTION PRODUCTS Marking SC LC01-6 YYWW PHIL Note: (1) yyww = Date Code Ordering Information Part Number Working Voltage Qty/Pkg R eel Size LC01-6.TD 6V 1000/Reel 13 Inch 6V 1000/Reel 13 Inch 6V 46/Tube N /A 6V 46/Tube N /A LC01-6.TDT (1) LC01-6 LC01-6.T (1) Note: (1) Lead-Free Product Contact Information for Semtech International AG Taiw an Branch Korea Branch Tel: 886-2-2748-3380 Fax: 886-2-2748-3390 Semtech Sw itz erland GmbH Japan Branch Tel: 81-3-6408-0950 Fax: 81-3-6408-0951 Tel: 82-2-527-4377 Fax: 82-2-527-4376 Semtech Limited (U.K.) Tel: 44-1794-527-600 Fax: 44-1794-527-601 Tel: 86-21-6391-0830 Fax: 86-21-6391-0831 Semtech France SARL Tel: 33-(0)169-28-22-00 Fax: 33-(0)169-28-12-98 Semtech International AG is a wholly-owned subsidiary of Semtech Corporation, which has its headquarters in the U.S.A. Semtech Germany GmbH Tel: 49-(0)8161-140-123 Fax: 49-(0)8161-140-124 2004 Semtech Corp. 7 Shanghai Office www.semtech.com