FSL128MRT Green-Mode Fairchild Power Switch (FPS™) for High Input Voltage Features Description Internal Avalanched Rugged 800V SenseFET Advanced Soft Burst-Mode Operation for Low The FSL128MRT is an integrated Pulse Width Modulation (PWM) controller and SenseFET specifically designed for offline Switch-Mode Power Supplies (SMPS) with minimal external components. The PWM controller includes an integrated fixed-frequency oscillator, Under-Voltage Lockout (UVLO), LeadingEdge Blanking (LEB), optimized gate driver, internal soft-start, temperature-compensated precise current sources for loop compensation, and self-protection circuitry. Compared with a discrete MOSFET and PWM controller solution, the FSL128MRT can reduce total cost, component count, size, and weight; while simultaneously increasing efficiency, productivity, and system reliability. This device provides a basic platform suited for cost-effective design of a flyback converter. Standby Power and Low audible noise Under 40mW Standby Power Consumption at 265VAC and No-load Condition Random Frequency Fluctuation for Low EMI Pulse-by-Pulse Current Limit Various Protection Functions: Overload Protection (OLP), Over-Voltage Protection (OVP), Abnormal Over-Current Protection (AOCP), Internal Thermal Shutdown (TSD) with Hysteresis and Under-Voltage Lockout (UVLO) with Hysteresis Low Operating Current(0.4mA) in Burst Mode Internal Startup Circuit Built-in Soft-Start: 15ms Auto-Restart Mode Applications Power Supply for STB Home Appliances and Industrial for High AC Input Ordering Information (2) Part Number FSL128MRT Package Output Power Table Operating Current RDS(ON) 230VAC ± 15%(3) 85~265VAC Junction Limit (Max.) Open Open (4) (4) Temperature Adapter (5) Adapter (5) Frame Frame TO-220F (1) 6-Lead W-Forming -40°C ~ +125°C 1.2A 7.3Ω 30W 40W 17W 25W Replaces Device KA5M0280RY DTU Notes: 1. Pb-free package per JEDEC J-STD-020B. 2. The junction temperature can limit the maximum output power. 3. 230VAC or 100/115VAC with voltage doubler. 4. Typical continuous power in a non-ventilated enclosed adapter measured at 50°C ambient temperature. 5. Maximum practical continuous power in an open-frame design at 50°C ambient temperature. © 2012 Fairchild Semiconductor Corporation FSL128MRT • Rev. 1.0.0 www.fairchildsemi.com FSL128MRT — Green-Mode Fairchild Power Switch (FPS™) for High Input Voltaage May 2012 FSL128MRT — Green-Mode Fairchild Power Switch (FPS™) for High Input Voltage Application Circuit VO AC IN VSTR Drain GND VCC FB Figure 1. Typical Application Circuit Internal Block Diagram VSTR VCC Drain 6 3 1 Vburst ICH 0.40V / 0.55V Soft-Burst VREF VCC Good 7.5V / 12V Random VCC VREFf 2.0µA IDELAY FB Soft-Start 90µA IFB OSC PWM 4 S Q R Q Gate Driver 3R R NC LEB(350ns) 5 VAOCP VSD TSD S Q R Q 2 GND 7.0V VCC VCC Good VOVP 24.5V Figure 2. Internal Block Diagram © 2012 Fairchild Semiconductor Corporation FSL128MRT • Rev. 1.0.0 www.fairchildsemi.com 2 6. VSTR 5. NC 4. FB 3. VCC 2. GND 1. Drain Figure 3. Pin Configuration (Top View) Pin Definitions Pin # Name 1 Drain SenseFET Drain. High-voltage power SenseFET drain connection. 2 GND Ground. This pin is the control ground and the SenseFET source. 3 VCC Power Supply. This pin is the positive supply input, which provides the internal operating current for both startup and steady-state operation. 4 FB Feedback. This pin is internally connected to the inverting input of the PWM comparator. The collector of an opto-coupler is typically tied to this pin. For stable operation, a capacitor should be placed between this pin and GND. If the voltage of this pin reaches 7V, the overload protection triggers, which shuts down the FPS. 5 NC No Connection VSTR Startup. This pin is connected directly, or through a resistor, to the high-voltage DC link. At startup, the internal high-voltage current source supplies internal bias and charges the external capacitor connected to the VCC pin. Once VCC reaches 12V, the internal current source (ICH) is disabled. 6 Description © 2012 Fairchild Semiconductor Corporation FSL128MRT • Rev. 1.0.0 FSL128MRT — Green-Mode Fairchild Power Switch (FPS™) for High Input Voltage Pin Configuration www.fairchildsemi.com 3 Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter Min. Max. Unit VSTR VSTR Pin Voltage 650 V VDS Drain Pin Voltage 800 V VCC VCC Pin Voltage 26 V VFB Feedback Pin Voltage 10.0 V -0.3 (6) IDM Drain Current Pulsed 8 A IDS Continuous Switching Drain Current 2 A EAS Single Pulsed Avalanche Energy(7) 67 mJ 47 W 150 °C -40 +125 °C -55 +150 °C PD TJ TSTG Total Power Dissipation (TC=25°C) (8) Maximum Junction Temperature Operating Junction Temperature (9) Storage Temperature Notes: 6. Repetitive peak switching current when the inductive load is assumed: Limited by maximum duty (DMAX=0.74) and junction temperature (see Figure 1). 7. L=10mH, starting TJ=25°C. 8. Infinite cooling condition (refer to the SEMI G30-88). 9. Although this parameter guarantees IC operation, it does not guarantee all electrical characteristics. Figure 4. Repetitive Peak Switching Current ESD Capability Symbol ESD Parameter Value Human Body Model, JESD22-A114 4.5 Charged Device Model, JESD22-C101 2.0 Unit KV FSL128MRT — Green-Mode Fairchild Power Switch (FPS™) for High Input Voltage Absolute Maximum Ratings Thermal Impedance TA=25°C unless otherwise specified. Symbol Parameter θJA Junction-to-Ambient Thermal Impedance θJC Junction-to-Case Thermal Impedance(11) (10) Value Unit 63.5 °C/W 2.6 °C/W Notes: 10. Free standing without heat sink under natural convection condition, per JEDEC 51-2 and 1-10. 11. Infinite cooling condition per Mil Std. 883C method 1012.1. © 2012 Fairchild Semiconductor Corporation FSL128MRT • Rev. 1.0.0 www.fairchildsemi.com 4 Unless otherwise specified TJ = 25°C. Symbol Parameter Conditions Min. Typ. Max. Unit SenseFET Section BVDSS Drain-Source Breakdown Voltage VCC=0V, ID=250μA IDSS Zero-Gate-Voltage Drain Current VDS=640V, TA=125°C Drain-Source On-State Resistance VGS=10V, ID=1A 6.3 RDS(ON) (12) 800 V 250 μA 7.3 Ω CISS Input Capacitance VDS=25V, VGS=0V, f=1MHz 275 pF COSS Output Capacitance(12) VDS=25V, VGS=0V, f=1MHz 39 pF Reverse Transfer Capacitance VDS=25V, VGS=0V, f=1MHz 4.1 pF tr Rise Time VDS=400V, ID=2A, RG=25Ω 24.3 ns tf Fall Time VDS=400V, ID=2A, RG=25Ω 28.7 ns td(on) Turn-On Delay VDS=400V, ID=2A, RG=25Ω 13 ns td(off) Turn-Off Delay VDS=400V, ID=2A, RG=25Ω 20 ns CRSS (12) Control Section fS ΔfS Switching Frequency(12) VCC=14V, VFB=4V Switching Frequency Variation (12) 61 -25°C < TJ < 125°C 73 kHz ±5 ±10 % 67 73 % 0 % DMAX Maximum Duty Ratio VCC=14V, VFB=4V DMIN Minimum Duty Ratio VCC=14V, VFB=0V Feedback Source Current VFB=0 65 90 115 μA VFB=0V, VCC Sweep 11 12 13 V After Turn-on, VFB=0V 7.0 7.5 8.0 V IFB VSTART VSTOP tS/S UVLO Threshold Voltage Internal Soft-Start Time 61 67 VCC Sweep 15 ms Burst-Mode Section VBURH VBURL Burst-Mode Voltage VCC=14V, VFB Sweep 0.46 0.55 0.66 V 0.33 0.40 0.48 V Hys 150 mV Protection Section ILIM Peak Drain Current Limit di/dt=300mA/μs 1.05 1.20 1.34 A VSD Shutdown Feedback Voltage VCC=14V, VFB Sweep 6.45 7.00 7.55 V VCC=14V, VFB=4V 1.2 2.0 2.8 μA VCC Sweep 23.0 24.5 26.0 V Shutdown Temperature 130 140 150 °C IDELAY Shutdown Delay Current (12)(14) tLEB Leading-Edge Blanking Time VOVP Over-Voltage Protection TSD Hys Thermal Shutdown Temperature(12) 350 Hysteresis 60 FSL128MRT — Green-Mode Fairchild Power Switch (FPS™) for High Input Voltage Electrical Characteristics ns °C Continued on the following page… © 2012 Fairchild Semiconductor Corporation FSL128MRT • Rev. 1.0.0 www.fairchildsemi.com 5 Unless otherwise specified TJ = 25°C. Symbol Parameter Conditions Min. Typ. Max. Unit 0.3 0.4 0.5 mA 1.0 1.4 mA Total Device Section IOP IOPS ISTART ICH VSTR Operating Supply Current, (Control Part in Burst Mode) Operating Switching Current, (Control Part and SenseFET Part) VCC=14V, VFB=0V VCC=14V, VFB=2V Start Current VCC=11V (Before VCC Reaches VSTART) 85 120 155 μA Startup Charging Current VCC=VFB=0V, VSTR=40V 0.7 1.0 1.3 mA Minimum VSTR Supply Voltage VCC=VFB=0V, VSTR Sweep 26 V Notes: 12. Although these parameters are guaranteed, they are not 100% tested in production. 13. Average value 14. tLEB includes gate turn-on time. Comparison of KA5M0280R and FSL128MRT Function KA5M0280RYDTU FSL128MRT Random Frequency Fluctuation N/A Built-in Operating Current 7mA 0.4mA High-Voltage Startup Circuit N/A Built-in Protections OLP OVP TSD OLP OVP AOCP TSD with Hysteresis Power Balance Long TCLD Very Short TCLD © 2012 Fairchild Semiconductor Corporation FSL128MRT • Rev. 1.0.0 Advantages of FSL128MRT Low EMI Very low stand-by power Enhanced protections and high reliability The difference of input power between the low and high input voltage is quite small FSL128MRT — Green-Mode Fairchild Power Switch (FPS™) for High Input Voltage Electrical Characteristics (Continued) www.fairchildsemi.com 6 1.40 1.40 1.30 1.30 1.20 1.20 1.10 1.10 Normalized Normalized Characteristic graphs are normalized at TA=25°C. 1.00 0.90 1.00 0.90 0.80 0.80 0.70 0.70 0.60 0.60 -40'C -20'C 0'C 25'C 50'C 75'C 90'C 110'C 120'C 125'C Temperature [ °C] -40'C -20'C 1.40 1.40 1.30 1.30 1.20 1.20 1.10 1.10 1.00 0.90 1.00 0.90 0.80 0.80 0.70 0.70 0.60 0.60 -40'C -20'C 0'C 25'C 50'C 75'C 90'C 110'C 120'C 125'C Temperature [ °C] -40'C -20'C Figure 7. Startup Charging Current (ICH) vs. TA 0'C 25'C 50'C 75'C 90'C 110'C 120'C 125'C Temperature [ °C] Figure 8. Peak Drain Current Limit (ILIM) vs. TA 1.40 1.40 1.30 1.30 1.20 1.20 1.10 1.10 Normalized Normalized 25'C 50'C 75'C 90'C 110'C 120'C 125'C Temperature [ °C] Figure 6. Operating Switching Current (IOPS) vs. TA Normalized Normalized Figure 5. Operating Supply Current (IOP) vs. TA 0'C 1.00 0.90 FSL128MRT — Green-Mode Fairchild Power Switch (FPS™) for High Input Voltage Typical Performance Characteristics 1.00 0.90 0.80 0.80 0.70 0.70 0.60 0.60 -40'C -20'C 0'C 25'C 50'C 75'C -40'C -20'C 90'C 110'C 120'C 125'C 0'C 25'C 50'C 75'C 90'C 110'C 120'C 125'C Temperature [ °C] Temperature [ °C] Figure 9. Feedback Source Current (IFB) vs. TA © 2012 Fairchild Semiconductor Corporation FSL128MRT • Rev. 1.0.0 Figure 10. Shutdown Delay Current (IDELAY) vs. TA www.fairchildsemi.com 7 1.40 1.40 1.30 1.30 1.20 1.20 1.10 1.10 Normalized Normalized Characteristic graphs are normalized at TA=25°C. 1.00 0.90 0.80 0.70 0.70 0.60 -40'C -20'C 0'C 25'C 50'C 75'C 90'C 110'C 120'C 125'C Temperature [ °C] -40'C -20'C Figure 11. UVLO Threshold Voltage (VSTART) vs. TA 1.40 1.40 1.30 1.30 1.20 1.20 1.10 1.10 1.00 0.90 0'C 25'C 50'C 75'C 90'C 110'C 120'C 125'C Temperature [ °C] Figure 12. UVLO Threshold Voltage (VSTOP) vs. TA Normalized Normalized 0.90 0.80 0.60 1.00 0.90 0.80 0.80 0.70 0.70 0.60 0.60 -40'C -20'C 0'C -40'C -20'C 25'C 50'C 75'C 90'C 110'C 120'C 125'C Temperature [ °C] Figure 13. Shutdown Feedback Voltage (VSD) vs. TA 0'C 25'C 50'C 75'C 90'C 110'C 120'C 125'C Temperature [ °C] Figure 14. Over-Voltage Protection (VOVP) vs. TA 1.40 1.40 1.30 1.30 1.20 1.20 1.10 1.10 Normalized Normalized 1.00 1.00 0.90 1.00 0.90 0.80 0.80 0.70 0.70 0.60 FSL128MRT — Green-Mode Fairchild Power Switch (FPS™) for High Input Voltage Typical Performance Characteristics 0.60 -40'C -20'C 0'C 25'C 50'C 75'C 90'C 110'C 120'C 125'C Temperature [ °C] -40'C -20'C Figure 15. Switching Frequency (fS) vs. TA © 2012 Fairchild Semiconductor Corporation FSL128MRT • Rev. 1.0.0 0'C 25'C 50'C 75'C 90'C 110'C 120'C 125'C Temperature [ °C] Figure 16. Maximim Duty Ratio (DMAX) vs. TA www.fairchildsemi.com 8 3. Feedback Control: This device employs CurrentMode control, as shown in Figure 18. An opto-coupler (such as the FOD817) and shunt regulator (such as the KA431) are typically used to implement the feedback network. Comparing the feedback voltage with the voltage across the RSENSE resistor makes it possible to control the switching duty cycle. When the reference pin voltage of the shunt regulator exceeds the internal reference voltage of 2.5V, the opto-coupler LED current increases, pulling down the feedback voltage and reducing drain current. This typically occurs when the input voltage is increased or the output load is decreased. 1. Startup: At startup, an internal high-voltage current source supplies the internal bias and charges the external capacitor (CVCC) connected to the VCC pin, as illustrated in Figure 17. When VCC reaches 12V, the FSL128MRT begins switching and the internal highvoltage current source is disabled. Normal switching operation continues and the power is supplied from the auxiliary transformer winding unless VCC goes below the stop voltage of 7.5V. 3.1 Pulse-by-Pulse Current Limit: Because CurrentMode control is employed, the peak current through the SenseFET is limited by the inverting input of PWM comparator (VFB*), as shown in Figure 18. Assuming that the 90μA current source flows only through the internal resistor (3R + R =27kΩ), the cathode voltage of diode D2 is about 2.4V. Since D1 is blocked when the feedback voltage (VFB) exceeds 2.4V, the maximum voltage of the cathode of D2 is clamped at this voltage. Therefore, the peak value of the current through the SenseFET is limited. Figure 17. 3.2 Leading-Edge Blanking (LEB): At the instant the internal SenseFET is turned on, a high-current spike usually occurs through the SenseFET, caused by primary-side capacitance and secondary-side rectifier reverse recovery. Excessive voltage across the RSENSE resistor leads to incorrect feedback operation in the Current-Mode PWM control. To counter this effect, the leading-edge blanking (LEB) circuit inhibits the PWM comparator for tLEB (350ns) after the SenseFET is turned on. Startup Block 2. Soft-Start: The internal soft-start circuit increases PWM comparator inverting input voltage, together with the SenseFET current, slowly after startup. The typical soft-start time is 15ms. The pulse width to the power switching device is progressively increased to establish the correct working conditions for the transformers, inductors, and capacitors. The voltage on the output capacitors is progressively increased to smoothly establish the required output voltage. This helps prevent transformer saturation and reduces stress on the secondary diode during startup. Figure 18. © 2012 Fairchild Semiconductor Corporation FSL128MRT • Rev. 1.0.0 FSL128MRT — Green-Mode Fairchild Power Switch (FPS™) for High Input Voltage Functional Description Pulse Width Modulation Circuit www.fairchildsemi.com 9 B increasing until it reaches 7.0V, when the switching operation is terminated, as shown in Figure 20. The delay for shutdown is the time required to charge CFB from 2.4V to 7.0V with 2.0µA. This protection is implemented in Auto-Restart Mode. B Figure 20. Figure 19. 4.2 Abnormal Over-Current Protection (AOCP): When the secondary rectifier diodes or the transformer pins are shorted, a steep current with extremely high di/dt can flow through the SenseFET during the minimum turn-on time. Even though the FSL128MRT has overload protection, it is not enough to protect in that abnormal case; due to the severe current stress imposed on the SenseFET until OLP is triggered. The internal AOCP circuit is shown in Figure 21. When the gate turn-on signal is applied to the power SenseFET, the AOCP block is enabled and monitors the current through the sensing resistor. The voltage across the resistor is compared with a preset AOCP level. If the sensing resistor voltage is greater than the AOCP level, the set signal is applied to the S-R latch, resulting in the shutdown of the SMPS. Auto-Restart Protection Waveforms 4.1 Overload Protection (OLP): Overload is defined as the load current exceeding its normal level due to an unexpected abnormal event. In this situation, the protection circuit should trigger to protect the SMPS. However, even when the SMPS is in normal operation, the overload protection circuit can be triggered during the load transition. To avoid this undesired operation, the overload protection circuit is designed to trigger only after a specified time to determine whether it is a transient situation or a true overload situation. Because of the pulse-by-pulse current-limit capability, the maximum peak current through the SenseFET is limited and, therefore, the maximum input power is restricted with a given input voltage. If the output consumes more than this maximum power, the output voltage (VOUT) decreases below the set voltage. This reduces the current through the opto-coupler LED, which also reduces the opto-coupler transistor current, increasing the feedback voltage (VFB). If VFB exceeds 2.4V, D1 is blocked and the 2.0µA current source starts to charge CFB slowly up. In this condition, VFB continues © 2012 Fairchild Semiconductor Corporation FSL128MRT • Rev. 1.0.0 Overload Protection Figure 21. FSL128MRT — Green-Mode Fairchild Power Switch (FPS™) for High Input Voltage 4. Protection Circuits: The FSL128MRT has several self-protective functions, such as Overload Protection (OLP), Abnormal Over-Current Protection (AOCP), Over-Voltage Protection (OVP), and Thermal Shutdown (TSD). All the protections are implemented as autorestart. Once the fault condition is detected, switching is terminated and the SenseFET remains off. This causes VCC to fall. When VCC falls to the Under-Voltage Lockout (UVLO) stop voltage of 7.5V, the protection is reset and the startup circuit charges the VCC capacitor. When VCC reaches the start voltage of 12.0V, the FSL128MRT resumes normal operation. If the fault condition is not removed, the SenseFET remains off and VCC drops to stop voltage again. In this manner, the auto-restart can alternately enable and disable the switching of the power SenseFET until the fault condition is eliminated. Because these protection circuits are fully integrated into the IC without external components, reliability is improved without increasing cost. Abnormal Over-Current Protection www.fairchildsemi.com 10 4.5 Thermal Shutdown (TSD): The SenseFET and the control IC on a die in one package makes it easier for the control IC to detect the over temperature of the SenseFET. If the temperature exceeds 140°C, the thermal shutdown is triggered and stops operation. The FSL128MRT operates in Auto-Restart Mode until the temperature decreases to around 80°C, when normal operation resumes. Figure 22. 6. Random Frequency Fluctuation (RFF): Fluctuating switching frequency of an SMPS can reduce EMI by spreading the energy over a wide frequency range. The amount of EMI reduction is directly related to the switching frequency variation, which is limited internally. The switching frequency is determined randomly by external feedback voltage and an internal free-running oscillator at every switching instant. This random frequency fluctuation scatters the EMI noise around typical switching frequency (67kHz) effectively and can reduce the cost of the input filter included to meet the EMI requirements (e.g. EN55022). 5. Soft Burst-Mode Operation: To minimize power dissipation in Standby Mode, the FSL128MRT enters Burst-Mode operation. As the load decreases, the feedback voltage decreases. The device automatically enters Burst Mode when the feedback voltage drops below VBURL (400mV), as shown in Figure 22. At this point, switching stops and the output voltages start to drop at a rate dependent on standby current load. This causes the feedback voltage to rise. Once it passes VBURH (550mV), switching resumes. The feedback voltage then falls and the process repeats. Burst Mode alternately enables and disables switching of the SenseFET, reducing switching loss in Standby Mode. Figure 23. © 2012 Fairchild Semiconductor Corporation FSL128MRT • Rev. 1.0.0 Burst-Mode Operation FSL128MRT — Green-Mode Fairchild Power Switch (FPS™) for High Input Voltage 4.4 Over-Voltage Protection (OVP): If the secondary-side feedback circuit malfunctions or a solder defect causes an opening in the feedback path, the current through the opto-coupler transistor becomes almost zero. Then VFB climbs up in a similar manner to the overload situation, forcing the preset maximum current to be supplied to the SMPS until the overload protection is triggered. Because more energy than required is provided to the output, the output voltage may exceed the rated voltage before the overload protection is triggered, resulting in the breakdown of the devices in the secondary side. To prevent this situation, an OVP circuit is employed. In general, the VCC is proportional to the output voltage and the FS136MRT uses VCC instead of directly monitoring the output voltage. If VCC exceeds 24.5V, an OVP circuit is triggered, resulting in the termination of the switching operation. To avoid undesired activation of OVP during normal operation, VCC should be designed to be below 24.5V. Random Frequency Fluctuation www.fairchildsemi.com 11 10.16 9.96 2.74 2.34 (7.00) 3.40 3.20 (0.70) Ø3.28 3.08 (5.40) 16.07 15.67 6.90 6.50 20.00 19.00 (13.05) 24.00 23.00 (0.48) R0.55 R0.55 8.13 1.40 7.13 1.20 (1.13) 3.06 2.46 (7.15) 0.80 0.70 1 0.70 0.50 6 2.19 2,4,6 1,3,5 0.60 0.45 1.75 3.48 2.88 1.27 3.81 5° NOTES: UNLESS OTHERWISE SPECIFIED A) THIS PACKAGE DOES NOT COMPLY TO ANY CURRENT PACKAGING STANDARD. B) ALL DIMENSIONS ARE IN MILLIMETERS. C) DIMENSIONS ARE EXCLUSIVE OF BURRS, MOLD FLASH, AND TIE BAR EXTRUSIONS. D) LEADFORM OPTION A E) DFAWING FILENAME: TO220A06REV4 5° Figure 24. FSL128MRT — Green-Mode Fairchild Power Switch (FPS™) for High Input Voltage Physical Dimensions TO-220F-6L (W-Forming) Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. © 2012 Fairchild Semiconductor Corporation FSL128MRT • Rev. 1.0.0 www.fairchildsemi.com 12 FSL128MRT — Green-Mode Fairchild Power Switch (FPS™) for High Input Voltage © 2012 Fairchild Semiconductor Corporation FSL128MRT • Rev. 1.0.0 www.fairchildsemi.com 13