05081 PP0640SA - PP3500SC Only One Name Means ProTek’Tion™ THYRISTOR SURGE SUPPRESSOR DESCRIPTION The PP-SM Series are thyristor surge suppression (TSS) devices designed to protect telecommunication equipment against lightning and transients induced by AC power lines. These devices can be used on central office equipment, PBX, DSU, OCU and other telecommunication equiment/systems. The bidirectional configuration provides protection for both positive and negative transients and the discrete surface mount package allows for individual placement of the device on line cards or other locations where multiple component devices do not offer the versatile in board trace layout. This series can be used to provide protection in accordance with industry standards such as FCC Part 68, ANSI C62.41, UL 1459, GR-1089-CORE, IEC 61000-2, IEC 61000-4 and IEC 61000-4-5 requirements. DO-214AA PACKAGE FEATURES APPLICATIONS • Compatible with IEC 61000-4-2 (ESD): Air 15kV, Contact 8kV • Compatible with IEC 61000-4-4 (EFT): 40A, 5/50ns • Compatible with IEC 61000-4-5 (Surge): 95A, 8/20µs - L4(LineGround), 48A - L4(Line-Line) & 83A - L2(Power) • FCC Part 68, UL 1459, Bellcore 1089 & ITU-K.20/K.21 Compliant • UL File Recognition #E208219 • Peak Off-State Voltage from 25 to 300 Volts • Surge Current Capability (See Table 1) • ESD Protection > 25 kilovolts • Low Capacitance for T1/E1 Trunk & Line Card Applications • Bidirectional Configuration • RoHS Compliant • REACH Compliant • T1/E1 Trunk & Line Cards • SLIC Line Card • DBX Branch Exchange Switches • FCC Part 68 Customer Premise Equipment • Line Interface Modem • xDSL Architecture Interface MECHANICAL CHARACTERISTICS DEVICE SYMBOL BIDIRECTIONAL • Molded Plastic DO-214AA Package • Approximate Weight: 0.095 grams • Lead-Free Pure-Tin Plating (Annealed) • Solder Reflow Temperature: Pure-Tin - Sn, 100: 260-270°C • Flammability Rating UL 94V-0 • 12mm Tape and Reel per EIA Standard 481 TABLE 1 - SURGE RATINGS SERIES I PP 2/10µs AMPS I PP 8/20µs AMPS I PP 10/160µs AMPS I PP 10/560µs AMPS I PP 10/1000µs AMPS I TSM 60Hz AMPS di/dt A/µs (Note 1) dv/dt V/µs (Note 1) SA 150 150 100 50 50 20 500 2000 SB 300 300 150 100 80 32 500 2000 SC 500 400 200 200 100 60 500 2000 NOTES 1. Critical rate of rise for On-State Current (di/dt) and Off-State Voltage (dv/dt). 05081.R16 7/15 Page 1 www.protekdevices.com 05081 PP0640SA - PP3500SC Only One Name Means ProTek’Tion™ TYPICAL DEVICE CHARACTERISTICS MAXIMUM RATINGS @ 25°C Unless Otherwise Specified PARAMETER SYMBOL VALUE UNITS Surge Current - 50/60Hz (SC Series) ITSM 60 Amps Junction Temperature TA -40 to 150 °C Storage Temperature TSTG -55 to 150 °C Thermal Resistance (Junction) - SA & SB Series RQJC 28 °C/Watt Thermal Resistance (Junction) - SC Series RQJC 26 °C/Watt Thermal Resistance (Ambient) - SA & SB Series RQJA 90 °C/Watt Thermal Resistance (Ambient) - SC Series RQJA 85 °C/Watt FIGURE 1 PULSE WAVEFORM IPP - Peak Pulse Current - % of IPP tf FIGURE 2 VI CHARACTERISITC CURVE TEST WAVEFORM PARAMETERS tf = 10µs td = 1000µs 100 Peak Value IPP IPP ITSM IT IS IH VS td = t/(IPP/2) IDRM 50 VDRM VT e-t 0 0 1 2 3 t - Time - ms FIGURE 3 ON-STATE CURRENT VS SURGE CURRENT DURATION Non-Repetitive On-State Current (ITSM) - Amps 100 PPxxxxSA PPxxxxSC PPxxxxSB 10 1 1 05081.R16 7/15 10 100 Surge Current Duration - Full Cycles Supply Frequency - 60 Hz Sinusoidal Page 2 1000 www.protekdevices.com 05081 PP0640SA - PP3500SC Only One Name Means ProTek’Tion™ TYPICAL DEVICE CHARACTERISTICS ELECTRICAL CHARACTERISTICS PER LINE @ 25°C Unless Otherwise Specified PART NUMBER DEVICE MARKING REPETITIVE SWITCHING MINIMUM SWITCHING MAXIMUM PEAK VOLTAGE HOLDING CURRENT OFF-STATE CURRENT CURRENT OFF-STATE VOLTAGE (Fig. 7) (Fig. 4) @100V/µs di/dt = 1A/ms @V DRM V DRM VS IH IS I DRM VOLTS VOLTS mA mA µA MAXIMUM ON-STATE VOLTAGE (Fig. 5) @I T VT VOLTS ON-STATE CURRENT TYPICAL CAPACITANCE (Note 1) IT AMPS @2V, 1MHz C pF PP0640SA GC 58 77 150 800 5 4 2.2 60 PP0720SA GD 65 88 150 800 5 4 2.2 60 PP0800SA GE 75 98 150 800 5 4 2.2 60 PP1100SA GF 90 130 150 800 5 4 2.2 60 PP1300SA GG 120 160 150 800 5 4 2.2 40 PP1500SA GH 140 180 150 800 5 4 2.2 40 PP1800SA GI 160 220 150 800 5 4 2.2 40 PP2300SA GJ 190 260 150 800 5 4 2.2 30 PP2600SA GK 220 300 150 800 5 4 2.2 30 PP3100SA GL 275 350 150 800 5 4 2.2 30 PP3500SA GM 300 400 150 800 5 4 2.2 30 PP0300SB GN 25 40 50 800 5 4 2.2 110 PP0640SB GP 58 77 150 800 5 4 2.2 60 PP0720SB GQ 65 88 150 800 5 4 2.2 60 PP0800SB GR 75 98 150 800 5 4 2.2 60 PP1100SB GS 90 130 150 800 5 4 2.2 60 PP1300SB GT 120 160 150 800 5 4 2.2 40 PP1500SB GU 140 180 150 800 5 4 2.2 40 PP1800SB GV 160 220 150 800 5 4 2.2 40 PP2300SB GW 190 260 150 800 5 4 2.2 30 PP2600SB GX 220 300 150 800 5 4 2.2 30 PP3100SB GY 275 350 150 800 5 4 2.2 30 PP3500SB GZ 300 400 150 800 5 4 2.2 30 PP0300SC HB 25 40 50 800 5 4 2.2 60 PP0640SC HC 58 77 150 800 5 4 2.2 120 PP0720SC HD 65 88 150 800 5 4 2.2 120 PP0800SC HE 75 98 150 800 5 4 2.2 120 PP1100SC HF 90 130 150 800 5 4 2.2 120 PP1300SC HG 120 160 150 800 5 4 2.2 80 NOTES 1. Capacitance imblance between positive and negative polarities is typically < 15pF. 05081.R16 7/15 Page 3 www.protekdevices.com 05081 PP0640SA - PP3500SC Only One Name Means ProTek’Tion™ TYPICAL DEVICE CHARACTERISTICS ELECTRICAL CHARACTERISTICS PER LINE @ 25°C Unless Otherwise Specified PART NUMBER DEVICE MARKING REPETITIVE SWITCHING MINIMUM SWITCHING MAXIMUM PEAK VOLTAGE HOLDING CURRENT OFF-STATE OFF-STATE CURRENT CURRENT VOLTAGE (Fig. 7) (Fig. 4) @100V/µs di/dt = 1A/ms @V DRM V DRM I DRM VS IH IS VOLTS VOLTS mA mA µA MAXIMUM ON-STATE VOLTAGE (Fig. 5) @I T VT VOLTS ON-STATE CURRENT IT AMPS TYPICAL CAPACITANCE (Note 1) @2V, 1MHz C pF PP1500SC HH 140 180 150 800 5 4 2.2 80 PP1800SC HI 160 220 150 800 5 4 2.2 80 PP2300SC HJ 190 260 150 800 5 4 2.2 60 PP2600SC HK 220 300 150 800 5 4 2.2 60 PP3100SC HL 275 350 150 800 5 4 2.2 60 PP3500SC HN 300 400 150 800 5 4 2.2 60 NOTES 1. Capacitance imblance between positive and negative polarities is typically < 15pF. 05081.R16 7/15 Page 4 www.protekdevices.com 05081 PP0640SA - PP3500SC Only One Name Means ProTek’Tion™ TYPICAL DEVICE CHARACTERISTICS 1 0.1 0.01 -40 0 40 80 tA - Temperature - °C FIGURE 5 TYPICAL PEAK ON-STATE CURRENT VS ON-STATE VOLTAGE 100 IT - On-State Current - A IDRM - Peak Off-State Current - µA 10 FIGURE 4 TYPICAL PEAK OFF-STATE CURRENT VS JUNCTION TEMPERATURE 10 1 120 0 FIGURE 6 TYPICAL NORMALIZED SWITCHING VOLTAGE VS JUNCTION TEMPERATURE 2 3 4 5 VT - On-State Voltage - V 6 7 FIGURE 7 TYPICAL NORMALIZED HOLDING CURRENT VS JUNCTION TEMPERATURE 1.10 2 Normalized IH Normalized VS 1 1 1 0.9 0.8 -40 05081.R16 7/15 0 40 80 tA - Temperature - °C 0 -40 120 Page 5 0 40 80 tA - Temperature - °C 120 www.protekdevices.com 05081 PP0640SA - PP3500SC Only One Name Means ProTek’Tion™ APPLICATION INFORMATION FIGURE 1 - UL 1459 & FCC PART 68 METALLIC PROTECTION The TSS (Thyristor Surge Suppressor) device is located across the tip-to-ring after a limiting resistor and fuse combination. RTIP and RRING resistors are optional depending upon the TSS device selection. Without the resistors, the PP3100SB/SC is recommended. However, with a resistance value of 7.5 Ohms for tip and ring, the PP3100SA is recommended. Digital signals may use a lower TSS device depending upon the total tip to ring voltage range. Selection of the TSS device, either PPxxxxSA or SB/SC is based upon the value of the tip and ring resistors. For the National Electric Code (NEC) article 800, it is recommended that at least one fuse be used in the tip or ring line for metallic surges. Fuses may be replaced with a suitable Positive Temperature Coefficient (PTC) automatic resettable current limiting device. TIP Fuse RTip To Protected Equipment RING RRing FIGURE 2 - UL 1459 & FCC PART 68 LONGITUDINAL PROTECTION There are two TSS devices, one located from tip-to-ground and one ring-to-ground. For standard analog signals, the PP3100SA is recommended with a typical resistor value for tip and ring of 15 Ohms. The PP3100SB/SC is recommended for resistor values of 7.5 Ohms each. The National Electric Code (NEC) article 800 requires two fuse elements when connecting to ground. Fuses or a suitable Positive Temperature Coefficient (PTC) automatic resettable current limiting device may be used. The purpose of this circuit is to limit AC power current from getting on the ground line causing any safety hazard. RTip TIP To Protected Equipment RING RRing 05081.R16 7/15 Page 6 www.protekdevices.com 05081 PP0640SA - PP3500SC Only One Name Means ProTek’Tion™ APPLICATION INFORMATION FIGURE 3 - UL 1459 & FCC PART 68 METALLIC & LONGITUDINAL PROTECTION Three equal TSS devices are used in this application for metallic (tip-to-ring) and longitudinal (tip-to-ground and ring-to-ground) protection. For analog signals, the PP3100SB/SC is recommended. With a resistance value of 15 Ohms for the tip and ring resistors, the PP3100SA may be used. The National Electric Code (NEC) article 800 requires two fuse elements when connecting to ground. Fuses or a suitable Positive Temperature Coefficient (PTC) automatic resettable current limiting device may be used. This circuit is recommended for protection against the Bellcore requirement: First Level Lightning Surge Tests (Telecommunications Port), document # GR-1089-CORE. RTip TIP To Protected Equipment RING RRing CIRCUIT BOARD RECOMMENDATIONS Circuit board layout is critical for electromagnetic compatibility protection. The following guidelines are recommended: • The protection device should be placed near the input terminals or connectors, the device will divert the transient current immediately before it can be coupled into the nearby traces. • The path length between the TVS device and the protected line should be minimized. • All conductive loops including power and ground loops should be minimized. • The transient current return path to ground should be kept as short as possible to reduce parasitic inductance. • Ground planes should be used whenever possible. For multilayer PCBs, use ground vias. 05081.R16 7/15 Page 7 www.protekdevices.com 05081 PP0640SA - PP3500SC Only One Name Means ProTek’Tion™ DO-214AA PACKAGE INFORMATION Polarity Band OUTLINE DIMENSIONS DIM MILLIMETERS INCHES MIN MAX MIN MAX A 1.96 2.21 0.077 0.087 B 4.06 4.57 0.160 0.180 C 3.30 3.94 0.130 0.155 D 2.00 2.50 0.079 0.098 E 0.76 1.52 0.030 0.060 F 0.10 0.20 0.004 0.008 G 5.08 5.59 0.200 0.220 H 0.15 031 0.006 0.012 A C B H D NOTES 1. Dimensions are exclusive of mold flash and metal burrs. E F G PAD LAYOUT DIMENSIONS DIM MILLIMETERS A INCHES MIN MAX MIN MAX A 2.15 - 0.084 - B 1.45 - 0.057 - C - 2.55 - 0.100 D 1.45 - 0.057 - 05081.R16 7/15 B Page 8 C D www.protekdevices.com 05081 PP0640SA - PP3500SC Only One Name Means ProTek’Tion™ TAPE AND REEL 10 Pitches Cumulative Tolerance on tape ± 0.2 P0 D t E F W K0 B0 A0 P User Direction of Feed SPECIFICATIONS REEL DIA. TAPE WIDTH 330mm (13”) 12mm A0 B0 K0 D E F 3.79 ± 0.15 5.72 ± 0.15 2.46 ± 0.30 1.55 ± 0.05 1.75 ± 0.10 W P0 P tmax 5.5 ± 0.05 12.00 ± 0.30 4.00 ± 0.10 8.00 ± 0.10 0.25 ± 0.10 NOTES 1. 2. 3. 4. Dimensions are in millimeters. Surface mount product is taped and reeled in accordance with EIA-481. Suffix - T = 13” Reel - 3,000 pieces per 12mm tape. Marking on Part - marking code (see page 2) and logo. ORDERING INFORMATION BASE PART NUMBER LEADFREE SUFFIX TAPE SUFFIX QTY/REEL REEL SIZE TUBE QTY PPxxxxSA/SB/SC -LF -T 3,000 13” n/a This device is only available in a Lead-Free configuration. 05081.R16 7/15 Page 9 www.protekdevices.com 05081 PP0640SA - PP3500SC Only One Name Means ProTek’Tion™ COMPANY INFORMATION COMPANY PROFILE In business more than 20 years, ProTek Devices™ is a privately held semiconductor company. The company offers a product line of overvoltage protection and overcurrent protection components. These include transient voltage suppressor array (TVS arrays) avalanche breakdown diode, steering diode TVS array and electronics SMD chip fuses. These components deliver circuit protection in electronic systems from numerous overvoltage and overcurrent events. They include lightning; electrostatic discharge (ESD); nuclear electromagnetic pulses (NEMP); inductive switching; and electromagnetic interference (EMI) / radio frequency interference (RFI). ProTek Devices also offers high performance interface and linear products. They include analog switches; multiplexers; LED drivers; LED wafer die for ESD protection; audio control ICs; RF and related high frequency products. CONTACT US Corporate Headquarters 2929 South Fair Lane Tempe, Arizona 85282 USA By Telephone General: 602-431-8101 Sales: & Marketing: 602-414-5109 Customer Service: 602-414-5114 Product Technical Support: 602-414-5107 By Fax General: 602-431-2288 By E-mail: Asia Sales: [email protected] Europe Sales: [email protected] U.S. Sales: [email protected] Distributor Sales: [email protected] Customer Service: [email protected] Technical Support: [email protected] ProTek Devices (Asia Pacific) Pte. Ltd. 8 Ubi Road 2, #06-19 Zervex Singapore - 408538 Tel: +65-67488312 Fax: +65-67488313 Web www.protekdevices.com COPYRIGHT © ProTek Devices 2000 - This literature is subject to all applicable copyright laws and is not for resale in any manner. SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice. DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice and that the final judgement concerning selection and specifications is the buyer’s and that in furnishing engineering and technical assistance. ProTek assumes no responsibility with respect to the selection or specifications of such products. ProTek makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ProTek assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability without limitation special, consequential or incidental damages. LIFE SUPPORT POLICY: ProTek Devices products are not authorized for use in life support systems without written consent from the factory. 05081.R16 7/15 Page 10 www.protekdevices.com