Datasheet

DM85 inrush
pcb power relay
• miniature pcb power relay
• Up to 80A inrush (20ms)
• AgSnO2 contacts
• RoHS Compliant
E305753
Contacts
Contact number & arrangement
SPST-NO (1 N/O)
Contact material
AgSnO2
Max. switching voltage
AC/DC 440VAC
Max. breaking capacity
AC1 4000VA
Min. switching current / voltage
Max. inrush current
Rated load
10mA/10VDC
80A (20ms)
AC1 16A, 250VAC (600 ops/hr)
AC15 3A, 120V / 1.5A, 240V (B300)
AC3 750W (single phase motor)
DC1 16A, 24VDC
DC13 0.22A, 120V / 0.1A, 250V (R300)
Initial resistance
≤ 100mΩ, max. at 0.1A/24VDC
Coil
Rated voltage
DC 3...110V
Must release voltage
DC ≥ 0.1Un
Operating range of supply voltage
Rated power consumption
See coil table 1
DC 0.4...0.48mW
Insulation (EN 60664-1)
Insulation rated voltage
AC 400VAC
Rated surge voltage
4000V 1.2 / 50 μs
Overvoltage category
III
Insulation pollution degree
3
Dielectric strength
coil to contact 5000Vrms, 1min
contact to contact 1000Vrms, 1min
Contact - coil distance
clearance ≥10mm
creepage ≥10mm
General Data
Operating/release time (typical)
mS ≤ 8ms/3ms
Electrical Life
ops >105 (16A 250VAC) (AC1 / DC1 @ 600 ops/hr)
Mechanical life
ops ≥ 3 x 107 (72000 ops/hr)
Dimensions
Weight
L x W x H 29 x 12.7 x 15.7mm
14g
Ambient temperature
storage -40 to 85°C
operating -40 to 85°C
Shock resistance
30g
Vibration resistance
10g 10~150Hz
Page 1 of 2 www.durakoolrelays.com
Ref: DM85 Inrush 090313JHM
Sales Department Tel: (888) 847-6552
Specifications are subject to change without notice. E&OE.
DM85 inrush
pcb power relay
Coil Data (DC voltage 400 ...480mW)
Table 1
Coil Voltage Code
Nominal Voltage (VDC)
Coil Resistance (Ω) ±10%
Must release voltage min.
(VDC)
Max. operating voltage
(VDC)
1003
3
22
2.1
7.6
1005
5
60
3.5
12.7
1006
6
90
4.2
15.3
1009
9
200
6.3
22.9
1012
12
360
8.4
30.6
1018
18
710
12.6
45.9
1024
24
1440
16.8
61.2
1036
36
3140
25.2
91.8
1048
48
5700
33.6
122.4
1060
60
7500
42.0
153.0
1110
110
25200
77.0
280.0
Note: Parameters at 20°C
Ordering codes
Contact Material
Type
D
M
8
5
-
5
0
Contact
arrangement
2
1
Cover protection
and mounting
-
2
5
Coil code
-
Contact material
50
-
see Table 1
AgSnO2
Contact arrangement
21
-
SPST-NO (1 N/O)
Cover protection category
2
-
in cover, flux tight - IP40
Connection mode
5
-
for PCB
Overall Dimensions
Fig. 1
Connection diagram
Fig. 2
Terminal (Pin) Dimensions
Terminal
(pin)
(mm)
Coil
A1(1); A2 (2)
Contacts
21 (4);11(7);
4(8); 24(5)
Ø 0.6
0.5 x 0.9
Drill Hole: Ø 1.3 +0.1mm
(Bottom View)
(Contact terminals should be tracked as shown above with
14 connected to 24, and 11 connected to 21 on the PCB)
Dimensions in mm
Page 2 of 2 www.durakoolrelays.com
Ref: DM85 Inrush 090313JHM
Sales Department Tel: (888) 847-6552
Specifications are subject to change without notice. E&OE.