OX-222 Oven Controlled Crystal Oscillator OX-222 Description The OX-222 is part of a series of oscillators specifically designed to support Timing Over Packet applications, in particular 15882008 based frequency and phase reference systems. The OX-222 is stratum 3E compliant. Features • • • • • Applications Available in three standard frequencies (10MHz, 12.8MHz, 20MHz, 24.576MHz and 25MHz) Excellent temperature stability Superior long term stability Optimised to support Timing Over Packet applications Stratum 3E compliant according to GR1244 • • • SETS clock support Wireless Base Stations Edge and Core Routers Performance Specifications Frequency Stability1 Parameter Min Typ Max Units Notes ±4.6 ppm Free run accuracy 10 ppb Over 24 hours and 400C window Drift ±1.0 ppb Over 24 hours and ±2.80C Temperature stability (df/f ) ±10 ppb -40 to 850C (-20 to 700C for 2226 version) Initial Tolerance (df/f0) ±500 ppb @250C vs. supply voltage change (df/f ) ±5 ppb static; 3.3V ± 5% vs. load change (df/f ) ±5 ppb static; Load ± 5% vs. aging / daily (df/f ) ±1 ppb after 30 days; @250C vs. aging / month (df/f ) ± 25 ppb after 30 days; @250C vs. aging / year (df/f ) ± 100 ppb after 30 days; @250C ±1 ppm after 30 days; @250C Max Units Notes < 1.00 Over all stability (df/f0) Holdover vs. aging / 10 years (df/f ) Phase Stability Parameter Min Typ Jitter ps rms @12kHz to 20MHz MTIE 1s 0.2 ns MTIE 10s 2.0 ns MTIE 100s 10.0 ns Wander Generation per GR1244, system performance when locked through a 1mHz loop bandwidth, see typical performance data. MTIE 1000s 40.0 ns Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page1 of 5 Performance Specifications Phase Stability (continued) Units Notes TDEV 1s Parameter Min 0.015 Typ Max ns TDEV 10s 0.13 ns TDEV 100s 1.5 ns Wander Generation per GR1244, system performance when locked through a 1mHz loop bandwidth, see typical performance data. TDEV 1000s 5.0 ns Phase Noise Parameter Min Typ Max Units Phase Noise at 1 Hz Offset -85 -60 dBc/Hz Phase Noise at 10 Hz Offset -110 -90 dBc/Hz Phase Noise at 100 Hz Offset -130 -115 dBc/Hz Phase Noise 1 kHz Offset -143 -130 dBc/Hz Phase Nosie at 10 kHz Offset -150 -145 dBc/Hz Notes 20MHz output RF Output Signal LVCMOS Load 15 pF ±10% Rise Time < 10 ns @ 10% to 90% Vout Fall Time <10 ns @90% to 10% Vout Duty Cycle 45/55 % @ 1.65 V V Low x < 0.4 V V High x > 2.4 V Supply Supply Voltage (VS) 3.3±10% V Current consumption < 400 mA Steady state, @ VSnom, 250C Current consumption < 950 mA During warm up, @ VS Additional Parameters Warm Up Time <5 ROHS 100% ROHS 6 compliant Washable Non-washable device (non-hermetic). minutes @ 250C to final frequency Absolute Maximum Ratings Min Max Units Operating temperature range -40 85 0C Storage temperature range -50 85 0C 5.5 V Supply Voltage Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page2 of 5 Typical Performance Wander Generation per GR1244, system performance when locked through a 1mHz loop bandwidth. Outline Drawing / Enclosure Dimensions in mm Height Codes Code Height “H” 1 12.1 6 8.3 Pin Assignment Pin Connection 1 I.C. (do not connect) 2 N.C 3 VS (Supply) 4 RF Out 5 N.C 6 N.C 7 GND (case) Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page3 of 5 Tape and Reel Dimensions Lage im Gurt Position in tape Pin1 K 4.0 A 1.75±0.1 W B XXXXX XXXXX Abwickelrichtung Unwinding direction B R0 .75 P A ±0.05 A 0.20 Schnitt A - A B Bei W < 32mm nur obere Lochreihe vorhanden if W < 32mm only upper hole line existent Schnitt B - B Maßangaben in mm: Dimension in mm: A, B und K Maße von Bauelement abhängig A, B und K are dependent uppon component dimensions Fertigungstoleranzen entsprechen der DIN IEC 286-3 production tolerance complying DIN IEC 286-3 All dimensions in millimeters unless otherwise stated Enclosure Type Tape Width W (mm) Quantity per meter Quantity per reel Dimension P OX-2221 (12.1mm) 44 37.5 175 28 OX-2226 (8.3mm) 44 37.5 250 28 Recommended Reflow Profile IPC/JEDEC J-STD-020 (latest revision) Additional Information: This SMD oscillator has been designed for pick and place reflow soldering. SMD oscillators must be on the top side of the PCB during the reflow process. Additional Environmental Conditions Parameter Description Rapid temperature changes MIL-883-1010 Cond B 1000 cycles -55/125C Vibration MIL-STD-883 Meth 2007 Cond A 20G 20-2000Hz 4x in each 3axis 4 min Shock Mech.Shock MIL-STD-202 Meth 213 Cond.C 100G 6ms 6 shocks in each direction Solderability J_STD_002C Cond A, Through hole device/ Cond. B, SMD 255C (diving time 50,5sec.) Dip+Look with 8h damp pre-treatment: solder wetting >95% Solvent resistance MIL-STD-883 Meth 2015 Solv. 1,3,4 ESD HBM JESD22-A114-F Class 1C 10* 1000V Moisture Sensit. Level 1 JESD22-A113-B RoHS compliance 100% RoHS 6 compliant Washable non-washable device Note: All temperatures refer to topside of the package, measured on the package body surface. Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page4 of 5 Ordering Information OX - 222 1 - E A E - 108 0 - 20M0000000 Frequency Product Family OX: OCXO Frequency Control 0: Fixed Frequency Package 25x22mm SMT Height 1: 12.1mm 6: 8.3mm Supply Voltage E: +3.3V Stability Code 108: ±10ppb Temperature Range E: -40°C to +85°C J: -20°C to +70°C N: -5°C to +70°C RF Output Code A: HCMOS Notes: 1. Contact factory for improved stabilities or additional product options. Not all options and codes are available at all frequencies. 2. Unless other stated all values are valid after warm-up time and refer to typical conditions for supply voltage, frequency control voltage, load, temperature (25°C). 3. Phase noise degrades with increasing output frequency. 4. Subject to technical modification. 5. Contact factory for availability. For Additional Information, Please Contact USA: Vectron International 267 Lowell Road Suite 102 Hudson, NH 03051 Tel: 1.888.328.7661 Fax: 1.888.329.8328 Europe: Vectron International Landstrasse, D-74924 Neckarbischofsheim, Germany Tel: +49 (0) 7268.801.100 Fax: +49 (0) 7268.801.282 Asia: Vectron International 1589 Century Avenue, the 19th Floor Chamtime International Financial Center Shanghai, China Tel: 86.21.6081.2888 Fax: 86.21.6163.3598 Disclaimer Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Rev: 18 Feb 2014 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page5 of 5