VTC4 series Voltage Controlled Temperature Compensated Crystal Oscillator Features • Clipped Sine Wave Output • Output Frequencies to 27 MHz • Fundamental Crystal Design • Optional VCXO Function available • Gold over nickel contact pads • Hermetically Sealed Ceramic SMD package The VTC4, VCTXCO • Product is compliant to RoHS directive and fully compatible with lead free assembly Applications • Wireless Communications • Base Stations • Point to point radios • Broadband Access • Test Equipment • Handsets Description Vectron’s VTC4 Temperature Compensated Crystal Oscillator (TCXO) is a quartz stabilized, clipped sine wave output, temperature compensated oscillator, operating off either a 2.8, 3.0, 3.3 or 5.0 volt supply. Vectron International: 267 Lowell Road, Suite 102, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: [email protected] VTC4 Data Sheet Performance Characteristics Table 1. Electrical Performance Parameter Frequency 1 Typical Supply Voltage Ordering option, see last page Supply Current 10.000 MHz to < 15.000 MHz 15.000 MHz to 27.00 MHz 2 Output Level Output Load Control Voltage Impedance Control Voltage to reach pull All options (5.0, 3.3,3.0 and 2.8V) Pull Range Ordering option, see last page Temperature Stability Ordering option, see last page. Initial Accuracy, “No Adjust” option Power Supply Stability Load Stability Aging Operating temperature Ordering option, see last page Phase Noise, 12.800MHz 10 Hz offset 100 Hz offset 1 kHz offset 10 kHz offset 100 kHz offset 5MHz offset Start-up time Symbol fO Min Typical Maximum 10.000 27.000 2.8, 3.0, 3.3 or 5.0 Units MHz V IDD mA 1.5 2.0 Vp/p 0.8 V 10K II 10pf ZVc 1 Mohm V 0.5 TPR 2.5 ±5, ±8, ±10, ±15 ppm ±0.5 to ±5.0 ppm ±0.5 ±1.0 ppm ±0.2 ppm ±0.2 ppm ±1.0 ppm/year 0/55, -10/60, -20/70, -30/80, -40/85 °C dBc/Hz -89 -113 -137 -150 -155 -156 2 ms 1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended. 2. Output is DC coupled. Vectron International: 267 Lowell Rd, Suite 102, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: [email protected] VTC4 Data Sheet Figure 1. Typical Phase Noise Plot Figure 2. Clipped Sine Wave Output Vectron International: 267 Lowell Rd, Suite 102, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: [email protected] VTC4 Data Sheet VCXO Functional Description VCXO Feature: The VTC4 can be ordered with a VCXO function for applications where it will be used in a PLL, or the output frequency needs fine tune adjustments. This is a high impedance input, 1 Mohm, and can be driven with an op-amp or terminated with adjustable resistors etc. Pin 1 should not be left floating on the VCXO optional devices. “No Adjust” Feature: In applications where the VTC4 will not be used in a PLL, or the output frequency does not fine tune adjustments, the best device to use would be a VTC4-x0xx. By using the “no adjust” option, the circuit is simplified as Vc does not need to adjusted or set to a predetermined voltage and pin 1 should be grounded (pin 1 can be left open but should not be set to a voltage such as the supply). Outline Diagrams, Pad Layout and Pin Out Table 2. Pinout Pin # Symbol 1 GND or VC 2 GND 3 fO 4 VDD Function Ground for a VTC4-x0xx option or VCXO Control Voltage Electrical and Case Ground Output Frequency Supply Voltage NOTE: Additional pads are used to program and adjust the TCXO during manufacturing and should be left open; do not terminate these to the supply voltage. Some designs do not include these additional pads. Contact Pads are gold over nickel Devices will be marked with the frequency Figure 3, Package drawing Vectron International: 267 Lowell Rd, Suite 102, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: [email protected] VTC4 Data Sheet Tape and Reel Table 3. Tape and Reel Dimensions (mm) Tape Dimensions Product A VTC4 16 B C D E 7.5 1.5 4 8 Reel Dimensions F G H 1.5 20.2 13 I J K L 60 2 16.4 180 # Per Reel 1000 J F C D G B A L I E H K Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied at these or any other conditions in excess of conditions represented in the operational sections of this data sheet. Exposure to absolute maximum ratings for extended periods may adversely affect device reliability. Table 4. Absolute Maximum Ratings Parameter Symbol Storage Temperature Tstorage Table 5. Environmental Compliance Parameter Mechanical Shock Mechanical Vibration Temperature Cycle Solderability Gross and Fine Leak Resistance to Solvents Moisture Sensitivity Level Contact Pads Vectron International: 267 Lowell Rd, Suite 102, Hudson NH 03051 Ratings -55/125 Unit °C Conditions MIL-STD-883 Method 2002 MIL-STD-883 Method 2007 MIL-STD-883 Method 1010 MIL-STD-883 Method 2003 MIL-STD-883 Method 1014 MIL-STD-883 Method 2015 1 Gold over Nickel Tel: 1-88-VECTRON-1 e-mail: [email protected] VTC4 Data Sheet Handling Precautions Although ESD protection circuitry has been designed into the the VTC4, proper precautions should be taken when handling and mounting. VI employs a Human Body Model and a Charged-Device Model (CDM) for ESD susceptibility testing and design protection evaluation. ESD thresholds are dependent on the circuit parameters used to define the model. Although no industry wide standard has been adopted for the CDM, a standard HBM of resistance = 1.5kohms and capacitance = 100pF is widely used and therefore can be used for comparison purposes. Table 6. ESD Ratings Model Human Body Model Charged Device Model Minimum 1500 1000 Conditions MIL-STD-883 Method 3115 JESD 22-C101 Suggested IR profile Devices are built using lead free epoxy and can also be subjected to standard lead free IR reflow conditions, Table 7 shows max temperatures and lower temperatures can also be used e.g. peak temperature of 220C. Table 7. Reflow Profile (IPC/JEDEC J-STD-020) Parameter Symbol PreHeat Time tS Ramp Up R UP o Time Above 217 C tL Time To Peak Temperature t AMB-P o Time At 260 C (max) tP Time At 240 °C (max) tp2 Ramp Down R DN Vectron International: 267 Lowell Rd, Suite 102, Hudson NH 03051 6 Value 60 sec Min, 180 sec Max o 3 C/sec Max 60 sec Min, 150 sec Max 480 sec Max 10 sec Max 60 sec Max o 6 C/sec Max Tel: 1-88-VECTRON-1 e-mail [email protected] VTC4 Data Sheet Ordering Information Table 8. Standard Frequency List 10.000 12.504 12.800 14.7456 15.000 16.000 18.414 19.200 19.440 23.104 24.000 24.5535 VTC4 - B 13.000 16.325291 19.6608 24.576 0 13.568 16.367667 19.680 25.000 2 C 14.000 16.396 19.800 25.600 - Product Family 14.31818 16.800 20.000 26.000 14.4844 17.500 21.250 27.456 12M8000000 Output Frequency (MHz) TCXO, 5x3.2 Voltage Options Temperature Options A: +5.0 Vdc ±5%, Clipped Sine Output A: 0 to 55°C B: +3.3 Vdc ±5%, Clipped Sine Output B: -10 to 60°C C: +3.0 Vdc ±5%, Clipped Sine Output C: -20 to 70°C D: +2.8 Vdc ±5%, Clipped Sine Output D: -30 to 80°C E: -40 to 85°C Pulling Range 0: Fixed TCXO, no adjust Stability Options 1: ±5ppm A: ±0.5ppm 2: ±8ppm 1: ±1.0ppm 3: ±10ppm B: ±1.5ppm 4: ±15ppm 2: ±2.0ppm C: ±2.5ppm 3: ±3.0 ppm Note: Not all combinations are available: D: ±3.5ppm ±0.5 ppm is available over 0 / 55 °C, and on a case by case basis for -10/60C. 4: ±4.0ppm ±1.0 ppm to ±5.0 ppm is available on all temperature range 5: ±5.0ppm USA: Vectron International • 267For Lowell Road, Suite 102, Hudson,Please NH 03051 Additional Information, Contact: • Tel: 1-88-VECTRON-1 • Fax: 1-888-FAX-VECTRON EUROPE: Landstrasse, D-74924, Neckarbischofsheim, Germany • Tel: 49 (0) 7268 8010 • Fax: 49 (0) 7268 801281 www.vectron.com ASIA: Vectron International • 68 Yin Cheng Road (C), 22nd Floor, One LuJiaZui, Pudong, Shanghai 200120, China •Tel: 8621 61946886 • Fax: 8621 61946699 Feb 26, 2014 Vectron International: 267 Lowell Rd, Suite 102, Hudson NH 03051 7 Tel: 1-88-VECTRON-1 e-mail [email protected]