optotronic® ot 15/220-240/12 p

Technical
Information
OPTOTRONIC®
OT 15/220-240/12 P
Constant Voltage LED Power Supply for 12V Edition: Mar 2013
LED - Modules
subject to change
Technical data
Reference:
For LED modules:
Nominal Voltage:
Line current, nominal:
Mains frequency:
Protection Class:
Output voltage:
(Remark)
Output Power:
Rated Power factor:
Power loss:
ECG efficiency:
(Remark)
Power loss in no load condition:
Input Voltage:
(Remark)
DC voltage operation:
Inrush current:
(Remark)
Max. no. of ECG @ circuit
breakers 10 A (B type):
Max. no. of ECG @ circuit
breakers 16 A (B type):
Ambient temperature range, ta:
Temperature range at storage
Max. case temperature at tc point:
ECG Life time:
(Remark)
Maximum casing temperature in
case of fault:
Dimmable:
No-load proof:
Short circuit protection:
Overload protection:
Overtemperature protection:
20130313
AA416090055
OT 15/220-240/12 P
12V LED Modules
with respect to the output parameters:
BackLED and BoxLED
220 – 240 VAC
0,18 A [email protected] V
50/60 Hz
II
12,5V DC
+/- 0,5V
15 W
> 0, 5 (full load) @ 230V
3,5 W max.
80 % @ 230V
full load at 230 V
<1W
198 - 264 VAC
Permitted Voltage Range
No
≤ tbd A
twidth = 170µs(measured at 50% Ipeak)
32
51
-25 °C to +55 °C
-30 °C to +85°C
+80°C
50.000h
at tcase = +70 °C at tc point and 10% failure rate
100°C
No
Yes
Automatic, reversible
Automatic, reversible
Automatic, reversible
Page 1 of 3
Technical
Information
OPTOTRONIC®
OT 15/220-240/12 P
Constant Voltage LED Power Supply for 12V Edition: Mar 2013
LED - Modules
subject to change
Cable cross section input side:
Cable cross section output side:
Cable types, Input side :
(Remark)
Cable types, Output side:
(Remark)
Wire preparation length, input side:
Wire preparation length, output side
Max. cable length-system:
Geometry (l x w x h)
Mounting hole spacing, length:
Weight:
Casing:
IP Code:
Suitable for fixtures with
protection class:
ECG outdoor protection against
humidity:
Safety:
Performance:
Radio interference:
Harmonic content:
Immunity:
Vibration tested:
Surge capability
Galvanic insulation
primary/secondary:
(Remark)
1,0 mm² / 17 AWG
1,0 mm²/ 17 AWG
Flexible
~300 mm
colour coding L: brown
N: blue
Flexible
~300 mm
colour coding LEDModule (+): red
LEDModule (-): black
10 mm
10 mm
10 m
237 x 20 x 22 mm³
213 mm
170 g
Plastic, White
IP66
II
PCB fully encapsulated + dust proof plastic
housing
IEC 61347-1, IEC 61347-2-13
IEC 62384
CISPR 15
IEC 61000-3-2
IEC 61547
Yes
L-N: 4kV
3,75 kVrms,
SELV - equivalent
Approvals:
20130313
AA416090055
Page 2 of 3
Technical
Information
OPTOTRONIC®
OT 15/220-240/12 P
Constant Voltage LED Power Supply for 12V Edition: Mar 2013
LED - Modules
subject to change
Geometry
l = 180 mm, l1 = 171 mm, w = 50 mm, w1 = 14 mm, h = 34 mm, h1 = 12 mm
Ordering information
OT 30/220-240/24 P
EAN 10
4052899905542
EAN 40
4052899905573
Installation notes
1. The luminaire manufacturer is responsible for providing the required clearances and
creepage distances and also for the protection against electrical shock, especially for
the line and load wires.
2. Ballast losses and LED Module heat radiation can lead to heat accumulation in a
complete closed case. Therefore it is necessary to ensure, that the temperature at the
measuring point tc does not exceed the maximum value.
Instruction sheet
Please consult the instruction sheet for further important information on e.g. wire
stripping and wiring limitations in system installations. The instruction sheet is enclosed
with the device or available upon request.
20130313
AA416090055
Page 3 of 3