MSM DP 19 Metal Line Switches www.schurter.com/PG70 Momentary action switch double pole MSM 19 DP PI red Description -Available in version Standard, lettered, with Point Illumination or Ring Illumination -Assembly method: clip micro-switch into the saddle, secure switch using mounting nut -Equipped with flat-pin plugs to permit fast connection Standards -DIN EN 61058-1 -UL 1054 Approvals -Low Voltage Directive 2006/95/EC Low Voltage Directive 2006/95/EC -VDE / ENEC Certificate Number (Omron): 40008425, 129246, 125256 -UL / CSA File Number (Omron): E41515 -VDE / ENEC Certificate Number (Marquardt): 097550 -UL / CSA File Number (Marquardt): E41791 -KEMA / ENEC File Number (Cherry): 2089323.01 -UL / CSA File Number (Cherry): E23301 Characteristics -Housing and actuating area material: high-quality stainless steel for use in harsh environments -Variety of design options regarding size, colour, illumination, connection or lettering -Switching voltage from 30 VDC to 250 VAC, switching current from 0.1 A to 10 A -optional with point or ring illumination -double pole version with two switching contact sets, can be wired as NO, NC or as change-over -IP-Protection: IP 67 from front side to contact area, Micro-Switch is available in versions IP 40 or IP 67, moving actuator is rated IP 40 to frontside References Alternative: Standard version MSM 19 Alternative: switch with latching function: MSM LA 19; MSM LA CS 19 Alternative: switch with backlighted illumination: MSM CS 19; MSM LA CS 19 Weblinks html-datasheet, General Product Information, CE declaration of conformity, RoHS, CHINA-RoHS, e-Shop, CAD-Drawings, Product News, Detailed request for product Switches 1 MSM DP 19 Metal Line Switches www.schurter.com/PG70 Technical Data Electrical Data Switching Function Number of Poles Supply Voltage Mechanical Data Actuating Force Actuating Travel N.O., N.C., N.O./N.C. 2 pole 24 / 12 / 5 VDC Ring Illumination, Point Illumination without series resistor, LED operating data are listed in separate table Surge Strength 4 kV MSM ST / MSM LE Micro Switch 5 A / 125 VAC or 3 A / 250 VAC, IP40 Contact Material Ag Switching Voltage max. 125 / 250 VAC Switching Current max. 5 / 3 A Rated Switching Capacity 750 W Lifetime 0.2 million actuations at Rated Switching Capacity Contact Resistance < 30 mΩ Insulation Resistance > 100 MΩ Duration of Bounce < 5 ms Micro Switch 0,1 A / 30 VDC, IP40 Contact Material Au Switching Voltage max. 30 VDC Switching Current max. 0.1 A Rated Switching Capacity 3 W Lifetime 0.2 million actuations at Rated Switching Capacity Contact Resistance < 50 mΩ Insulation Resistance > 100 MΩ Duration of Bounce < 5 ms Micro Switch for Electrical Rating 10 A / 250 VAC (Protection Class IP40) Contact Material Ag Switching Voltage max. 250 VAC Switching Current max. 10 A Rated Switching Capacity 2500 W Lifetime 0.2 million actuations at Rated Switching Capacity Contact Resistance < 30 mΩ Insulation Resistance > 100 MΩ Duration of Bounce < 5 ms Micro Switch 5 A / 250 VAC, IP67 Switching Voltage max. 250 VAC Switching Current max. 5 Rated Switching Capacity 1250 W Lifetime 0.05 million actuations at Rated Switching Capacity Micro Switch 0,1 A / 250 VAC, IP67 - on request Switching Voltage max. 250 VAC Switching Current max. 0.1 Rated Switching Capacity 25 W Lifetime 0.05 million actuations at Rated Switching Capacity Micro Switch 10 A / 250 VAC, IP67 - on request Switching Voltage max. 250 VAC Switching Current max. 10 A Rated Switching Capacity 2500 W Lifetime 0.01 million actuations at Rated Switching Capacity 2 Switches Lifetime Shock Protection Tightening Torque Plastic Nut Tightening Torque Stainless Steel Nut Climatical Data Operating Temperature Storage Temperature IP-Protection Salt Spray Test (acc. to DIN 50021-SS) Material Housing Actuator Light Conductor (Point Illumination) Illuminated Ring (Ring Illumination) Gasket Switcher Collet Intermediate Connector nonilluminated Intermediate Connector illuminated Switcher Adapter 5.0 N 1.0 mm, for mounting diameter 19, 22 mm 1.2 mm for mounting diameter 30 mm 1.5 million actuations IK 07 , max. 4.5 Nm for thread M19, 3.5 Nm for M22, 8 Nm for M30 max. 12 Nm for thread M19, 16 Nm for M22, 50 Nm for M30 -25 to +85 °C -25 to +85 °C IP 67 Front Side Contact Area, IP 40 Front Side mechanical, IP 40 / IP 67 Rear Side Contact Area optional 24 h / 48 h / 96 h Residence Time Stainless Steel Stainless Steel PC PA NBR70 PA PA PA PA MSM DP 19 Metal Line Switches www.schurter.com/PG70 Dimension MSM 19 DP ST MSM 19 DP LE C 18,15-0,05 COM NO NC MSM 19 DP PI 1,75 0,50 22,80 2,80 ø15,80 0,50 22,80 max. 6 mm 37,40 max. 6 mm 10,50 37,40 15,80 2,80 22 M19x0,75 ø22 1,75 22 M19x0,75 ø22 10,50 C COM NO NC MSM 19 DP RI C max. 6 mm 37,40 15,70 10,66 max. 6 mm 10,50 37,40 ø15,80 ø2 0,50 25,80 2,80 22 M19x0,75 ø22 1,75 M19x0,75 2,80 10,50 22 ø22 1,75 C 0,50 25,80 A A NC NO COM 18,15-0,05 NC NO COM 18,15-0,05 Legend A = Illumination Area B = Actuating Area C = Width Across Flats D = Nut 0.20 0.20 Tolerance Range Actuator Tolerance Range The mounting tolerance range of the actuator varies from 0.2 mm projection length and 0.2 mm short length to the housing edge. The slanting position of the actuator can range within this tolerance. The mounting tolerance range of the actuator varies from 0.2 mm projection length and 0.2 mm short length to the housing edge. The slanting position of the actuator can range within this tolerance. Switches 3 MSM DP 19 Metal Line Switches www.schurter.com/PG70 Dimension MSM 19 DP LE / MSM 19 DP PI / MSM 19 DP RI optional MSM 19 DP ST / MSM 19 DP RI Drilling diagram Drilling diagram Assembly Instructions I Housing II Flat Pin Terminal (Illumination) III Gasket IV Nut (Nut type see Dimensions) V Module Switching Contact Installation Instruction: 1.) Place the gasket accurately on the actuator housing. Then mount the actuator housing assembly into the panel. 2.) Tighten the screw nut according to the torque instructions. 3.) Clasp the module switching contact into the actuator housing. Installation information: 1.) The power supply and the configuration of the flat pin terminals have to be installed correctly for the illumination and micro switch function. 2.) Insulate the terminals as required. Fully insulated plug-in sleeves are recommended. 3.) Installation instructions according to VDE-standard DIN VDE 0100-100 or alternatively IEC 60354 standard 4 Switches MSM DP 19 Metal Line Switches www.schurter.com/PG70 Diagrams MSM DP ST / MSM DP LE MSM DP PI COM COM NO NC NO NC COM NO NC COM NO NC MSM DP RI D3 D4 D2 D5 D1 D6 Rv COM NO NC COM NO NC Rv Point Illumination Operating Data Forward Current max. Forward Voltage at 10 mA Forward Voltage at 8 mA Forward Voltage at 20 mA Forward Voltage max. LED red 30 mA 1.9 VDC 3.0 VDC LED green 30 mA 2.1 VDC 3.0 VDC LED yellow 30 mA 2.1 VDC 3.0 VDC LED blue 20 mA LED white 30 mA 3.7 VDC 4.5 VDC 3.6 VDC 4.0 VDC Attention: Switches are delivered without series resistor. Lettering The last three digits in the order number define the lettering: 000 No Lettering 001-074 Standard Lettering 101- Customized Lettering Lettering Colour of Laser Lettering Material Lettering Colour Stainless Steel black Filled letters For further Lettering details see also weblink: General Product Information Switches 5 MSM DP 19 Metal Line Switches www.schurter.com/PG70 Order Index Lettering Laser Marking 001 = A 021 = U 041 = ÷ 061 = EIN 002 = B 022 = V 042 = ✳ 062 = AUS 003 = C 023 = W 043 = = 063 = AUF 004 = D 024 = X 044 = # 064 = AB 005 = E 025 = Y 045 = ↔ 065 = ON 006 = F 026 = Z 046 = ↕ 066 = OFF 007 = G 027 = 0 047 = → 067 = UP 008 = H 028 = 1 048 = ← 068 = DOWN 009 = I 029 = 2 049 = ↓ 069 = HIGH 010 = J 030 = 3 050 = ↑ 070 = LOW 011 = K 031 = 4 051 = % 071 = ON/OFF 012 = L 032 = 5 052 = √ 072 = START 013 = M 033 = 6 053 = CTRL 073 = RESET 014 = N 034 = 7 054 = RETURN 074 = 015 = O 035 = 8 055 = SHIFT 075 = 016 = P 036 = 9 056 = LOCK 076 = 017 = Q 037 = + 057 = STOP 018 = R 038 = - 058 = ENTER 019 = S 039 = . 059 = BACK 020 = T 040 = x 060 = LINE All Variants Diameter Switching Current Switching Voltage [mm] [A] [VAC/ VDC] 19 5 / 3 A 125 / 250 VAC Illumination, LED Housing Material, Torsion Protection Actuator Material Config. Code Order Number non-illuminated Stainless Steel ,no Stainless Steel MSM 19 DP ST 1241.6921.1120000 █ 19 5 / 3 A 125 / 250 VAC non-illuminated Stainless Steel ,yes Stainless Steel MSM 19 DP LE 1241.6922.1120000 19 5 / 3 A 125 / 250 VAC Point Illumination, red Stainless Steel ,yes Stainless Steel MSM 19 DP PI red 1241.6923.1121000 █ 19 5 / 3 A 125 / 250 VAC Point Illumination, green Stainless Steel ,yes Stainless Steel MSM 19 DP PI green 1241.6923.1122000 █ 19 5 / 3 A 125 / 250 VAC Point Illumination, blue Stainless Steel ,yes Stainless Steel MSM 19 DP PI blue 1241.6923.1124000 19 5 / 3 A 125 / 250 VAC Ring Illumination, red, 24 VDC Stainless Steel ,yes Stainless Steel MSM 19 DP RI red 1241.6924.1121000 █ 19 5 / 3 A 125 / 250 VAC Ring Illumination, green, 24 VDC Stainless Steel ,yes Stainless Steel MSM 19 DP RI green 1241.6924.1122000 █ 19 5 / 3 A 125 / 250 VAC Ring Illumination, blue, 24 VDC Stainless Steel ,yes Stainless Steel MSM 19 DP RI blue 1241.6924.1124000 █ Legend: Type: MSM CS = Ceramic Surface ST = Standard: not lettered LE = Lettering: lettered AI = BL = Full Surface Backlighting: Lettering possible (see Lettering, last 3 digits) Alu red = red anodized aluminum housing, actuator stainless steel 1241.6622.3120062 -> 3 last numbers (062) see Order Index Lettering IP-Protection: IP 67 from front side to contact area, Micro-Switch is available in versions IP 40 or IP 67, see Technical Data Micro-Switch Ring illuminated versions: supply voltage 24 VDC, 12 VDC (E), 5 VDC (B), (further 12 and 5 VDC versions on request) Customer-specific versions available on request. Special materials for use in salt and chlorinated environment on request. The nut with gasket and micro switch are enclosed in the box. █ Most Popular. Availability for all products can be searched real-time:http://www.schurter.com/en/Stock-Check/Stock-Check-SCHURTER 6 Switches MSM DP 19 Metal Line Switches www.schurter.com/PG70 Packaging unit 10 in box with insert or packed in air cushion bags - Actuating elements in ESD safe packaging - Screw nuts and sealing rings in a bag (enclosd in the box) - Micro switches in a bag (enclosed in the box) Accessories Description Installation Wrench MSM 22 Installation wrench 03.03.2015 The specifications, descriptions and illustrations indicated in this document are based on current information. All content is subject to modifications and amendments. Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability and test each product selected for their own applications. Switches 7