ROHM TCOP0J106M8R

TCO series P Case
Tantalum capacitors
Chip tantalum capacitors
TCO Series P Case
zFeatures (P)
zDimensions (Unit : mm)
1) Conductive polymer used for the
Anode mark
cathode material.
2) Ultra-low ESR.
(1/10 compared with the conventional type)
W
L
3) Screening by thermal shock.
H
1
W2
S
S
+
−
(Unit : mm)
P case
Dimensions
L
2.0 +
− 0.2
W1
1.25 +
− 0.2
W2
0.9 +
− 0.2
H
1.1 +
− 0.1
S
0.45 +
− 0.3
zPart No. Explanation
Nominal capacitance in pF in
3 digits: 2 significant figures
followed by the figure
representing the number of 0's.
Series name
T C O
Case style
P
Nominal capacitance
0
J
Rated voltage
Code
Rated voltage (V)
0J
6.3
1A
10
1
0
6
M
8 R
Capacitance tolerance
Code Capacitance tolerance
M
+− 20%
8 : Tape width
R : Positive electrode
on the side opposite
to sprocket hole
Rev.C
1/8
TCO series P Case
Tantalum capacitors
zRated Table. Marking
TCO Series! P Case
Rated voltage (V.DC)
μF
6.3
0J
N
3.3
S
4.7
W
6.8
a
10
e
15
j
22
n
33
s
47
w
68
10
1A
∗P
∗P
∗ Under development
z Marking
The indications listed below should be given on the surface of a capacitor.
(1) Polarity
: The polarity should be shown by bar. (on the anode side)
(2) Rated DC voltage : Due to the small size of P case, a voltage code is used as shown below.
(3) Visual typical example
(1) voltage code (2) capacitance code
Rated DC
Voltage (V)
2.5
Capacitance
Code
A
Nominal
Capacitance (μF)
1.0
g
4
E
1.5
j
6.3
J
2.2
A
10
N
3.3
S
4.7
W
6.8
a
10
e
15
j
22
Voltage
Code
e
n
33
s
47
Voltage code
Capacitance code
P case
(2012)
ja
Rev.C
2/8
TCO series P Case
Tantalum capacitors
zCharacteristics
Item
Operating Temperature
Performance
−55 C to +105 C
Test conditions
(based on JIS C 5101−1 and JIS C 5101−3)
Voltage reduction when temperature exceeds+85 C
Maximum operating
+85 C
temperature with no voltage
derating
Rated voltage
(VDC)
6.3 10
at 85 C
Category voltage
(VDC)
5
Surge voltage
(VDC)
8 13
at 85 C
DC Leakage current
3μA or 0.1CV whichever is greater
Shown in " Standard list "
Rated voltage for 5min
Capacitance tolerance
+
−20% Shall be satisfied allowance range.
Tangent of loss angle
(Df, tan δ)
8
at 105 C
Measuring frequency : 120+
−12Hz
Measuring voltage : 0.5Vrms
+1.5 to 2V.DC
Measuring circuit
: DC Equivalent series circuit
Shall be satisfied the voltage on " Standard list " Measuring frequency : 120 +
−12Hz
Measuring voltage : 0.5Vrms
+1.5 to 2V.DC
Measuring circuit
: DC Equivalent series circuit
Shall be satisfied the voltage on " Standard list " Measuring frequency : 100 +
−10kHz
Measuring voltage : 0.5Vrms or less
ESR
Resistance to Appearance There should be no significant abnormality.
Soldering heat
The indications should be clear.
L.C.
ΔC / C
Less than 150% of initial limit
Within +
− 20% of initial value
tan δ
Less than 150% of initial limit
Dip in the solder bath
+5 C
Solder temp
: 240−
Duration
: 10+
−0.5s
:1
Repetition
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
Rev.C
3/8
TCO series P Case
Tantalum capacitors
Item
Temperature
cycle
Performance
Appearance There should be no significant abnormality.
L.C
Less than 500% of initial limit
ΔC / C
Within+
−20% of intial value
Df
(tan δ)
Less than 150% of initial limit
Test conditions
(based on JIS C 5101−1 and JIS C 5101−3)
Repetition : 5 cycles
(1 cycle : steps 1 to 4) without discontinuation.
1
2
3
4
Temp.
−55+
−3 C
Room temp.
105+
−2 C
Room temp.
Time
30+
−3min
3min.or less
30+
−3min
3min.or less
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
Moisture
resistance
Temperature
Stebility
Appearance There should be no significant abnormality.
The indications should be
L.C
Less than 150% of initial limit
ΔC / C
+30% / −20%
Df
(tan δ)
Less than 150% of initial limit
Temp.
−55 C
ΔC / C
Within 0/−20% of initial value
Df
(tan δ)
Shall be satisfied the voltage on " Standard list "
−
L.C
Surge
voltage
Temp.
+105 C
ΔC / C
Within +50/0% of initial value
Df
(tan δ)
Shall be satisfied the voltage on " Standard list "
L.C
Less than 1CV
Appearance There should be no significant abnormality.
L.C
ΔC / C
Df
(tan δ)
After leaving the sample under such atmospheric
condition that the temperature and humidity are
+ 2 C and 90 to 95% RH,respectiveiy,for 500 −
+ 24h
40 −
leave it at room
temperature for over 24h and then measure the
sample.
Less than initial limit
+ 20% of initial value
Within −
Less than initial limit
Apply the specified serge voltage every 5+
− 0.5 min.
for 30+
−5 s. each time in the atmospheric condition
of 85+
−2 C.
Repeat this rocedure 1,000 times.
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
Rev.C
4/8
TCO series P Case
Tantalum capacitors
Item
Performance
Loading at
Appearance There should be no significant
High temperature
abnormality.
L.C
Less than 200% of initial limit
ΔC / C
Within +
− 20% of initial value
Df
(tan δ)
150% of initial limit less than
Terminal strength Capacitance The measured value should be stable.
Appearance There should no significant abnormality.
Test conditions
(based on JIS C 5101−1 and JIS C 5101−3)
After applying the rated voltage for 1000+36 h
without discontinuation via the serial resistance
+ 2 C, leave
of 3Ω or less at a temperature of 85 −
the sample at room temperature / humidity for
over 24h and measure the value.
A force is applied to the terminal until it bends
to 1mm and by a perscribed tool maintain the
condition for5s.(See the figure below)
20
50
(Unit : mm)
F (Apply force)
R230
1mm
thickness=1.6mm
45
Adhesiveness
The terminal should not come off.
45
Apply force of 5N in the two directions shown
+ 1s after mounting the
in the figure below for 10 −
terminal on a circuit board.
product
YAA
C105
Apply force
a circuit board
Dimensions
Refer to "External dimensions"
Measure using a caliper of JISB 7507 Class 2
or higher grade.
Resistance to solvents
The indication should be clear
Solderability
3/4 or more surface area of the solder coated
terminal dipped in the soldering bath should
be covered with the new solder.
+ 5s, at room
Dip in the isopropyl alcohol for 30 −
temperature.
+ 2.5mm / s
Dip speed=25 −
Pre−treatment(accelerated aging): Leave
the sample on the boiling distilled water for 1 h.
Solder temp.
. : 245+
−5C
: 3+
Duration
− 0.5s
: M705
Solder
: Rosin25%
Flux
IPA75%
Frequency : 10 to 55 to 10Hz/min.
Amplitude : 1.5mm
Time : 2h each in X and Y directions
Mounting : The terminal is soldered on a print
circuit board.
Vibration
Capacitance Measure value should not fluctuate during the
measurement.
Appearance There should no significant abnormality.
Rev.C
5/8
TCO series P Case
Tantalum capacitors
zStandard list, TCO series
< P case : 2012 size >
Part No.
Rated
Voltage
85°C
Category
Voltage
105°C
Surge
Voltage
85°C
Cap.
120Hz
(V)
(V)
(V)
(μF)
5
8
8
13
10
4.7
TCO P 0J 106
6.3
10
TCO P 1A 475
=Tolerance(M : ± 20%)
Df
ESR
Tolerance Leakage
120Hz
100kHz
Current
(%)
25°C
1WV 5min
25°C
105°C (mΩ)
−55°C
(μA)
(%)
85°C
+
− 20
+
− 20
6.3
4.7
6
6
6
6
9
9
500
500
zPackaging specifications
Reek [ P case ]
4.0± 0.1
4.0± 0.1
+1.0
9.0 0
Chip
φ60 +1
0
B
11.4+
−1.0
φ13+
−0.2
3.5± 0.05
A
t1
8.0± 0.2
0.1
0
φ1.5
t2
2.0± 0.05
0
φ180 −1.5
1.75± 0.1
Tape [ P case ]
Feeding direction
Unit : [mm]
Case
A+
−0.1
B+
−0.1
t1 +
− 0.05
t2 +
− 0.1
P
1.55
2.3
0.25
1.5
Pull direction
Labelsticling position
EIAJ ET−7200B compatible
zPackaging style
Case code
package
P
Taping
Packaging style
plastic taping
Symbol Basic ordering units
φ180mmReel
R
3,000pcs
z Damp proof package
One reel is packed in aluminum bag.
The size of aluminum bag is 240(g) x 250(b)mm.
The size up to 230(c)mm is to zipper.
A desiccant is packed with a reel.
The aluminum bag is heat-sealed.
The label of the same as the label on the reel is placed om the
aluminum bag.
b
C
a
Rev.C
6/8
TCO series P Case
Tantalum capacitors
LEAKAGE CURRENT RATIO DCL / DCL
z Electrical characteristics and operation notes
(1) Leakage current-to-voltage ratio
1
0.1
0.01
0
20
40
60
80
100
% OF RATED VOLTAGE (VR)
Fig.1
(2) Derating voltage as function of temperature
100
105°C
PERCENT OF 85°C RVDC1 (VR)
85°C
90
Rated Voltage
Surge Voltage
Category Voltage
(V.DC)
(V.DC)
(V.DC)
6.3
8
5
10
13
8
80
70
60
50
75
85
95
105
TEMPERATURE (°C)
Fig.2
(3) Reliability
The malfunction rate of tantalum solid state electrolytic capacitors varies considerably depending on the conditions of
usage (ambient temperature, applied voltage, circuit resistance).
Formula for calculating malfunction rate
Op = Ob u (SE u SSR u SQ u SCV)
Op
Ob
SE
SSR
SQ
SCV
: Malfunction rate stemming from operation
: Basic malfunction rate
: Environmental factors
: Series resistance
: Level of malfunction rate
: Capacitance
For details on how to calculate the malfunction rate stemming from operation, see the tantalum solid state electrolytic
capacitors column in MIL-HDBK-217.
Rev.C
7/8
TCO series P Case
Tantalum capacitors
(4) Impedance frequency characteristics
1000
(5) ESR frequency characteristics
10000
TCOP0J106M
P case 6.3V10μF
TCOP0J106M
P case 6.3V10μF
1000
100
ESR (Ω)
CAPACITANCE (μF)
100
10
10
1
1
0.1
0.1
0.01
0.1
1
10
100
1000
0.01
0.01
0.1
1
10
100
FREQUENCY (kHz)
FREQUENCY (kHz)
Fig.3
Fig.4
(6) Capacitance temperature characteristics 120Hz
1000
(7) ESR temperature characteristics 100kHz
1
30
TCOP0J106M
P case 6.3V10μF
TCOP0J106M
P case 6.3V10μF
10
ESR (Ω)
CAP CHANGE (%)
20
0
0.1
−10
−20
−30
−55
−15
25
65
105
0.01
−55
−15
25
65
TEMPERATURE ( C)
TEMPERATURE ( C)
Fig.5
Fig.6
105
Rev.C
8/8
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level
of reliability and the malfunction of which would directly endanger human life (such as medical
instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers
and other safety devices), please be sure to consult with our sales representative in advance.
It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance
of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow
for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in
order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM
cannot be held responsible for any damages arising from the use of the products under conditions out of the
range of the specifications or due to non-compliance with the NOTES specified in this catalog.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact your nearest sales office.
ROHM Customer Support System
www.rohm.com
Copyright © 2007 ROHM CO.,LTD.
THE AMERICAS / EUPOPE / ASIA / JAPAN
Contact us : [email protected] rohm.co. jp
21, Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan
TEL : +81-75-311-2121
FAX : +81-75-315-0172
Appendix1-Rev2.0