TAI-SAW TECHNOLOGY CO., LTD. SMD 5.0x3.2 20MHz VCTCXO MODEL NO.: TX0216A REV. NO.: 2.0 Revise: Rev. Rev. Page Rev. Account Date 1 N/A Initial release 10/26/10’ N/A TAI-SAW TECHNOLOGY CO., LTD. Ref. No. Reviser Ginger Huang TST DCC Release document 2 TAI-SAW TECHNOLOGY CO., LTD. No. 3, Industrial 2nd Rd., Ping-Chen Industrial District, Taoyuan, 324, Taiwan, R.O.C. TEL: 886-3-4690038 FAX: 886-3-4697532 E-mail: [email protected] Web: www.taisaw.com SMD 5.0x3.2 20MHz VCTCXO MODEL NO.: TX0216A REV. NO.: 2.0 Features: z z z Miniature SMD Package Good Frequency Stability Good Phase Noise Response Description and Applications: Surface mount 5.0mmx3.2mmm VCTCXO for use in wireless communications devices Electrical Specifications: TX0216A Specifications Nominal Frequency, Fo 20.000000 MHz Storage Temperature Range -40°C to +85°C Operating Temperature Range -30°C to +85°C Power Supply Voltage, Vcc 3.0 V Output Voltage with Load 10pF//10KΩ, Vout 0.8 Vp-p min Power Supply Current, Icc 1.5 mA max Control Voltage, Vcon 1.5 +/- 1.0 V Frequency Tolerance (Vcon=1.5V) after Reflow +/- 2.0 ppm max @ 25°C +/- 3°C Frequency Stability a. Vs. Temperature (-30~85°C) b. Vs. Temperature (-40~-30°C) c. Vs. Supply Voltage varied 3.0V+/-5% d. Vs. Load varied +/-10% +/- 1.0 ppm +/- 2.0 ppm +/- 0.2 ppm +/- 0.2 ppm Vcon Frequency Control Range (1.5+/-1.0 V) +/-5 ~ +/-10 ppm/V Start Up Time (90% of final RF level in Vp-p) 2.0 msec max. Harmonics -8.0 dBc max SSB Phase Noise (@1KHz Carrier Offset) -130 dBc/Hz max Aging +/-1.0 ppm/year @25°C Marking Laser Marking TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 3 Mechanical Dimensions (mm): Marking: Line 1: Customer Frequency (20.000) Line 2: TST Logo + Product code + Date Code + Traceability Code (XX) 20.000 T XDXX ○ Product Code Table Year 2001 2005 2002 2006 2003 2007 2004 2008 Product Code X x X x Date Code Table WK01 WK02 WK03 WK04 WK05 WK06 WK07 WK08 WK09 WK10 WK11 WK12 A B C D E F G H I J K L WK13 M WK14 WK15 WK16 WK17 WK18 WK19 WK20 WK21 WK22 WK23 WK24 WK25 WK26 N O P Q R S T U V W X Y Z WK27 WK28 WK29 WK30 WK31 WK32 WK33 WK34 WK35 WK36 WK37 WK38 WK39 a b c d e f g h i j k l m WK40 WK41 WK42 WK43 WK44 WK45 WK46 WK47 WK48 WK49 WK50 WK51 WK52 n o p q r s t u v w x y z TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 4 Packing (mm): 1. Reel Dimension Unit:mm A B C D T M M2 W1 W2 Dimension 180 62 21 13 2.05 2.50 2.00 12.4 16.5 Tolerance ±0.1 ±0.5 ±0.1 ±0.5 ±0.5 ±0.5 ±0.2 +1.0/-0.0 ±0.2 2. Tape Dimension A B D D1 E F P0 P1 P2 T T2 W Dimension 3.81 5.74 1.50 1.50 1.75 5.50 4.00 8.00 2.00 2.24 0.292 12.00 Tolerance ±0.1 ±0.1 +0.1 +0.1 ±0.1 ±0.1 ±0.1 ±0.1 ±0.05 ±0.1 ±0.05 +0.3/-0.1 TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 5 Reflow Profile: 300 Reflow Area Rising Area Temperature (deg C) 250 Preheat Area Forced Cooling Area 200 150 100 Max peak temperature: 260 deg C 50 0 0 60 120 180 240 300 360 Time (seconds) Notes of the Usage: 1. Touch the solder iron at 260+/-5 deg C onto the leads for 10+/-2 sec max or touch the solder at 350+/-5 deg C onto the leads for 3+/-0.5 sec. 2. In the customer’s reflow process, if it will remain some mechanical stress at the soldering terminals, also make some cracks on the soldering termination. Some cracks will cause open or short circuit and cause of thermal increasing or smoking. Don’t make any excess mechanical stress to soldering points. 3. In case of giving a heavy shock to the products, it may make an open or short circuit and cause of thermal increasing and smoking. To avoid heavy shock impact applying to products is strictly required. Notes of the Storage: 1. To keep products under the condition at the room temperature (-5~35 deg C) with normal humidity (45~75%). Absorption of moisture and dewdrop may make inferiority of characteristics and a short circuit. 2. Oxidization of terminals shall make the solderability more inferior. Dusts and corrosive gas will make a cause of the open or short circuit. Keep it in the clean place where is not in dusty and no corrosive gas. 3. Use the unti-static material to the storage package. 4. Don’t put any excess weight to the VCTCXO in the storage process. 5. Don’t move the product from the cold place to the hot place in the short time, otherwise it may make some dew-drop, then a short circuit may happen in case. TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 6 6. Storage periods should be maximum 6 months under condition of above item 1 after delivery from TST factory. 7. Once open the bag, there is possibility of electrical characteristics deterioration due to absorption of moisture. So, please use parts within 7 days after opening the bag. 8. If you have to keep parts without using after opening the bag, please put the drying agent in the bag, fold the bag and keep it in the place where temperature and humidity are controlled (nitrogen atmosphere box etc.) TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 7