August 24, 2009 SMD INDUCTOR DR354-0 SERIES Features SMD 0402 Chip Inductor, Low Profile Suitable for High Frequency Application Inductance Range from 1.0nH to 68nH Operating Temp. -40°C to +125°C Tinned Leads with Leaded Solder is Available (note 4) ELECTRICAL SPECIFICATIONS AT 25ºC Part Number DR354-0-102 DR354-0-202 DR354-0-222 DR354-0-272 DR354-0-332 DR354-0-392 DR354-0-522-T DR354-0-562-T DR354-0-682-T DR354-0-822-T DR354-0-103-T DR354-0-123-T DR354-0-153-T DR354-0-183-T DR354-0-223-T DR354-0-273-T DR354-0-333-T DR354-0-393-T DR354-0-433-T DR354-0-473-T DR354-0-563-T DR354-0-683-T L(nH) Tolerance @250MHz 1.0 2.0 2.2 2.7 3.3 3.9 5.2 5.6 6.8 8.2 10 12 15 18 22 27 33 39 43 47 56 68 S S S S S S J,K J,K J,K J,K G,J,K G,J,K G,J,K G,J,K G,J,K G,J,K G,J,K G,J,K G,J,K G,J,K G,J,K G,J,K Q Min. 16 16 19 19 19 19 20 20 20 21 21 24 24 24 24 24 24 25 25 20 22 22 SRF (GHz) L Typ. Q Typ. L Typ. Q Typ. Min. DCR (Ohm) Max. Idc (mA) Max. 1.07 1.93 2.19 2.94 3.10 3.56 5.15 5.16 6.56 8.50 9.80 11.9 14.6 18.3 23.2 28.7 34.9 41.7 45.8 50.0 62.8 78.19 0.054 0.084 0.084 0.095 0.079 0.079 0.120 0.099 0.099 0.136 0.240 0.168 0.204 0.276 0.360 0.360 0.450 0.660 0.744 0.792 0.780 0.912 1360 1040 960 840 840 840 640 760 680 680 480 640 560 420 400 400 400 200 175 175 175 150 900MHz 77 54 59 50 65 45 56 54 63 57 50 53 55 57 53 49 31 47 46 38 42 36 1.7GHz 1.02 69 1.93 75 2.23 100 2.96 75 3.12 87 3.62 71 5.25 82 5.28 81 6.93 78 8.85 84 10.10 67 12.70 71 15.50 77 20.28 62 26.75 53 33.50 63 41.74 32 50.23 45 61.55 34 - 7.0 7.0 7.0 7.0 7.0 6.0 4.7 4.8 4.8 4.4 3.9 3.6 3.3 3.1 2.8 2.5 2.4 2.1 2.0 2.1 1.8 1.6 INDUCTANCE TOLERANCE: WHEN ORDERING, PLEASE SPECIFY THE TOLERANCE. T (K=±10%, J=±5%, G=±2%, S=±0.3nH) DATATRONIC: 28151 Highway 74, Romoland, CA 92585 Tel: 951-928-7700 Fax: 951-928-7701 Email: [email protected] 499 King’s Road, Hong KongTel: (852) 2562 3858, (852) 2564 8477 Fax: (852) 2565 7214, (852) 2563 1290 All specifications are subject to change without notice. Page 1 of 2 August 24, 2009 MECHANICAL OUTLINES 2X .23 .66 MAX .64 MAX 1.19 MAX .56 .25 .51 2X .66 2X .36 .46 SUGGESTED PAD LAYOUT SCHEMATIC Notes: 1. All dimensions are shown in millimeter “mm” 2. General tolerance 0.3mm, unless other specified 3. Tape and reel quantity, 8000 pcs/reel 4. For non-RoHS parts replace DR prefix with 42- (e.g. DR354-0 becomes 42-354-0) 5. Terminal finish is compliant to RoHS requirements. Solder in accordance with J-STD-020D DATATRONIC: 28151 Highway 74, Romoland, CA 92585 Tel: 951-928-7700 Fax: 951-928-7701 Email: [email protected] 499 King’s Road, Hong KongTel: (852) 2562 3858, (852) 2564 8477 Fax: (852) 2565 7214, (852) 2563 1290 All specifications are subject to change without notice Page 2 0f 2