ZMM1 ZMM75 (500 mW)

ZMM1 ... ZMM75 (500 mW)
ZMM1 ... ZMM75 (500 mW)
Surface mount Silicon Planar Zener Diodes
Silizium-Planar-Zener-Dioden für die Oberflächenmontage
0.3
0.3
3.5±0.1
Version 2015-05-13
Maximum power dissipation
Maximale Verlustleistung
500 mW
Nominal Z-voltage
Nominale Z-Spannung
1...75 V
Glass case MiniMELF
Glasgehäuse MiniMELF
SOD-80C
Weight approx.
Gewicht ca.
0.04 g
Standard packaging taped and reeled
Standard Lieferform gegurtet auf Rolle
Dimensions - Maße [mm]
Marking: One blue ring denotes “cathode” and “Z-Diode family”
The type numbers are noted only on the label on the reel
Kennzeichnung: Ein blauer Ring kennzeichnet “Kathode” und “Z-Dioden-Familie”
Die Typenbezeichnungen sind nur auf dem Rollenaufkleber vermerkt
Standard Zener voltage tolerance is graded to the international E 24 (~ ±5%) standard.
Other voltage tolerances and higher Zener voltages on request.
Die Toleranz der Zener-Spannung ist in der Standard-Ausführung gestuft nach der internationalen
Reihe E 24 (~ ±5%). Andere Toleranzen oder höhere Arbeitsspannungen auf Anfrage.
Maximum ratings and Characteristics
Grenz- und Kennwerte
ZMM-series
Power dissipation
Verlustleistung
TA = 25°C
Ptot
500 mW 1)
Operating junction temperature – Sperrschichttemperatur
Storage temperature – Lagerungstemperatur
Tj
TS
-50...+175°C
-50...+175°C
Thermal resistance junction to ambient air
Wärmewiderstand Sperrschicht – umgebende Luft
RthA
< 300 K/W 1)
Thermal resistance junction to terminal
Wärmewiderstand Sperrschicht – Anschluss
RthT
< 240 K/W
Zener voltages see table on next page – Zener-Spannungen siehe Tabelle auf der nächsten Seite
23
1
2
3
Mounted on P.C. board with 25 mm2 copper pads at each terminal
Montage auf Leiterplatte mit 25 mm2 Kupferbelag (Lötpad an jedem Anschluss
Tested with pulses – Gemessen mit Impulsen
The ZMM1 is a diode operated in forward. Hence, the index of all parameters should be “F” instead of “Z”.
The cathode, indicated by a band, has to be connected to the negative pole.
Die ZMM1 ist eine in Durchlass betriebene Si-Diode. Daher ist bei allen Kenn- und Grenzwerten der Index
© Diotec Semiconductor AG
http://www.diotec.com/
1
ZMM1 ... ZMM75 (500 mW)
Maximum ratings and Characteristics
Grenz- und Kennwerte
(Tj = 25°C unless otherwise specified)
Type
Typ
Zener voltage 2)
Zener-Spannung 2)
IZ = 5 mA
(Tj = 25°C wenn nicht anders spezifiziert)
Dynamic resistance
Diff. Widerstand
rzj [Ω] at f = 1 kHz
Temp. Coeffic.
of Z-voltage
…der Z-Spannung
Reverse volt.
Sperrspanng.
IR = 100 nA
Z-current 1)
Z-Strom 1)
TA = 25°C
Vzmin [V]
Vzmax [V]
IZ = 5 mA
IZ = 1 mA
αVZ [10-4 /°C]
VR [V]
IZmax [mA]
ZMM1 )
0.71
0.82
<8
< 50
-26...-23
–
400
ZMM2.4
2.28
2.56
< 85
< 600
-9...-6
1 (50 µA)
195
ZMM2.7
2.5
2.9
< 85
< 600
-9...-6
1 (10 µA)
172
ZMM3.0
2.8
3.2
< 85
< 600
-8...-5
1 (4 µA)
156
ZMM3.3
3.1
3.5
< 85
< 550
-8...-5
1 (2 µA)
143
ZMM3.6
3.4
3.8
< 85
< 550
-8...-5
1 (2 µA)
132
ZMM3.9
3.6
4.2
< 85
< 550
-8...-5
1 (2 µA)
119
ZMM4.3
4.0
4.6
< 75
< 500
-6...-3
1 (1 µA)
109
ZMM4.7
4.4
5.0
< 60
< 500
-5...+2
1 (0.5 µA)
100
ZMM5.1
4.8
5.4
< 35
< 500
-2...+2
1
93
ZMM5.6
5.2
6.0
< 25
< 450
-5...+5
1
83
ZMM6.2
5.8
6.6
< 10
< 200
+3...+6
2
76
ZMM6.8
6.4
7.2
<8
< 150
+3...+7
3
69
ZMM7.5
7.0
7.9
<7
< 50
+3...+7
5
63
ZMM8.2
7.7
8.7
<7
< 50
+3...+8
6
57
ZMM9.1
8.5
9.6
< 10
< 50
+3...+9
7
52
ZMM10
9.4
10.6
< 15
< 70
+3...+10
7
47
ZMM11
10.4
11.6
< 20
< 70
+3...+11
8
43
ZMM12
11.4
12.7
< 20
< 90
+3...+11
9
39
ZMM13
12.4
14.1
< 26
< 110
+3...+11
10
35
ZMM15
13.8
15.6
< 30
< 110
+3...+11
11
32
ZMM16
15.3
17.1
< 40
< 170
+3...+11
12
29
ZMM18
16.8
19.1
< 50
< 170
+3...+11
13
26
ZMM20
18.8
21.2
< 55
< 220
+3...+11
15
24
ZMM22
20.8
23.3
< 55
< 220
+4...+12
16
21
ZMM24
22.8
25.6
< 70
< 220
+4...+12
18
20
ZMM27
25.1
28.9
< 80
< 250
+4...+12
20
17
ZMM30
28
32
< 80
< 250
+4...+12
22
16
ZMM33
31
35
< 80
< 250
+4...+12
24
14
ZMM36
34
38
< 90
< 250
+4...+12
27
13
ZMM39
37
41
< 90
< 300
+4...+12
30
12
ZMM43
40
46
< 100
< 500
+4...+12
33
11
ZMM47
44
50
< 110
< 600
+4...+12
36
10
ZMM51
48
54
< 125
< 700
+4...+12
39
9
ZMM56
52
60
< 135
< 700
+4...+12
43
8
ZMM62
58
66
< 150
< 1000
+4...+12
47
8
ZMM68
64
72
< 200
< 1000
+4...+12
51
7
ZMM75
70
79
< 250
< 1000
+4...+12
56
6
3
1
2
“F” anstatt “Z” zu setzten. Die mit einem Balken gekennzeichnete Kathode ist mit dem Minuspol zu verbinden.
Notes see previous page – Fußnoten siehe vorhergehende Seite
http://www.diotec.com/
© Diotec Semiconductor AG
ZMM1 ... ZMM75 (500 mW)
10 3
120
[%]
[mA]
100
10
2
80
Tj = 100°C
10
60
Tj = 25°C
40
1
20
IF
IFAV
0
10
0
TA
100
50
150
-1
0
[°C]
150
3.3 3.8
2.7
Tj = 25°C
VF
0.4
0.6
4.7
5,6
[mA]
0.8
1.0
[V] 1.4
Forward characteristics (typical values)
Durchlasskennlinien (typische Werte)
1
Rated forward current versus ambient temperature )
Zul. Richtstrom in Abh. von der Umgebungstemp.1)
8,2
6,8
6,2
7,5
100
9,1
Tj = 25°C
f = 1.0 MHz
VR = 1V
[pF]
VR = 2V
IZmax
VR = 1V
50
VR = 2V
IZ
IZ = 5 mA
0
0
4
5
7
VZ
2
3
6
8
Typical breakdown characteristic – tested with pulses
Typische Abbruchspannung – gemessen mit Impulsen
[V]
10
Cj
VZ
[V]
Junction capacitance vs. zener voltage (typical)
Sperrschichtkapazität in Abh. v.d. Zenerspg. (typ.)
10
18
24
30
36
43
51
56
62
68
75
IZmax
Tj = 25°C
Typical breakdown characteristic – tested with pulses
Typische Abbruchspannung – gemessen mit Impulsen
© Diotec Semiconductor AG
http://www.diotec.com/
3
ZMM1 ... ZMM75 (500 mW)
4
http://www.diotec.com/
© Diotec Semiconductor AG