ROHM BP5729

Data Sheet
100-230VAC Input/24W Output
Isolated AC/DC Converter
BP5729
Absolute Maximum Ratings
Withstanding voltage
Allowable maximum
surface temperature
Operating temperature range
Storage temperature range
−25 to +80
−30 to +105
°C
°C
3.25MAX.
DC248 to DC372V
DC120 to DC372V
1s (primary - secondary)
Ambient temperature + The module
self-heating Tcmax
Electrical Characteristics
<In case of 12V output>
(Unless otherwise noted, Vi=311V, rated load Ta=25°C)
Parameter
Output voltage
Output current
Symbol
Vo
Io
Min.
11.4
0
Typ.
12.0
−
Max.
12.6
2000
Unit
V
mA
Vr
VI
Vp
η
−
−
−
82
13
20
0.16
90
200
200
0.5
−
mV
mV
Vp-p
%
Line regulation
Load regulation
Output ripple voltage
Power conversion efficiency
Conditions
Io=2000mA
Refer to derating curve
Vi=120 to 372V DC
Io=1000mA
Io=50 to 2000mA
∗
Io=2000mA
∗ Pulse noise is not included.
Sample Application Circuit
C8
D3
Be sure to use fuse for safety.
F1
ZNR
FL1
C1
C2
R2
D4
+
C5
R3
D2
C7
R4
C3
1 2 3
6
12
10
8
7
Pin
No.
1
6
3
2
Function
PC
This is the secondary side
opto-coupler current control terminal.
Vo
This is the secondary side output voltage
control terminal. Insert the output
smoothing capacitor between GND.
3
GND
This is the GND terminal for the secondary side.
6
ZCD
This is the zero current control terminal.
7
8
10
Vcc
Vi(-)
VH
This is the internal circuit power supply terminal.
This is the primary side input minus terminal.
This is the start teminal.
VD
This is the built-in FET of drain terminal.
The primary coil minus side of the
external transformer, and the snubber
circuit for noise reduction are connected
to this.
12
BP5729
Noise reduction capacitor
Rectifier diode
Rectifier diode
Rectifier diode
Diode bridge
Resistor
Resistor
Output voltage setting resistor
Resistor
Switching transformer
Fuse
AC line filter
Varistor
Name
1
2
External Components Specifications
C1,C2: Noise reduction capacitors
Input smoothing capacitor
C3:
Vcc smoothing capacitor
C4:
Noise reduction capacitor
C5:
Quasi-resonance capacitor
C6:
Output smoothing capacitor
C7:
Limiting element voltage AC250V or higher, 0.1 to 0.22µF
33µF / 450V General purpose type
10µF / 50V Low impedance type
2200pF / 630V
Use if necessary
1000µF / 35V x 2 Low impedance type
Rated ripple current 4.5Arms or higher ESR 18mΩ or below
2200pF / AC250V
FRD 200V / 0.5A
800V / 0.5A
60V / 20A
800V / 1A
47kΩ ±1% 0.1W
100kΩ ±5% 3W Limiting element voltage 300V or higher
68kΩ ±1% 0.1W
910Ω ±1% 0.1W
Be sure to use this for safety
A varistor is required to protect against lightning surges and static
electricity.
Usage Precautions
This product has built-in over current (reset type) and over voltage (latch type) protection functions to prevent
destruction due to surges. Discontinue operation if protection circuits are continuously active.
www.rohm.com
©2010 ROHM Co., Ltd. All rights reserved.
8
10
0.5±0.1
1.3±0.2
12
0.25±0.05
2.25MAX.
7.05MAX.
2.54X11=27.94TYP.
Derating Curve
27
24
21
Vi=248V to 372V
18
15
12
9
Vi=120V to 248V
6
3
0
-30-20-10 0 10 20 30 40 50 60 70 80 90 100
Ambient Current Ta(°C)
Switching Freguency
<In case of 12V output>
(Ta=25°C)
120
100
Burst Switching
Vi=311V
80
Vi=141V
60
40
Burst Switching
20
0
200 400 600
800 1000 1200 1400 1600 1800 2000
Output Current Io(mA)
+
C4
R1
C6
7
P=2.54±0.2
D1
T1
C8:
D1:
D2:
D3:
D4:
R1:
R2:
R3:
R4:
T1:
F1:
FL1:
ZNR:
MARKING SIDE
0
+
MARKING SIDE
Topr
Tstg
24.3MAX.
°C
4.0±1.0
105
Po
9.3MAX.
37.4MAX.
Output Power (W)
VI
Tcmax
Maximum power
Dimensions (Unit : mm)
Conditions
1/1
Conversion Efficiency
Conversion Efficiency η (%)
1-Pin input current
Unit
V
Apk
V
V
V
mA
mA
mA
W
W
kV
<In case of 12V output>
(Ta=25°C)
100
90
80
Vi=311V
Vi=141V
70
60
50
40
30
20
10
0
0 200 400 600 800 1000 1200 1400 1600 1800 2000
Output Current Io (mA)
Load Regulation
<In case of 12V output>
(Ta=25°C)
14.0
Output Voltage Vo(V)
6-Pin input current
Limits
720
1
400
30
9.2
−2.0
+3.0
10
24
12
2.5
Switching Frequency fsw (kHz)
Symbol
VD
ID
VH
VCC
Vzcd
Isozcd
Isizcd
Ipc
12.0
10.0
Vi=141V
Vi=311V
8.0
6.0
4.0
Maximum
Maximum
Io=2000mA
Io=1000mA
(Vi=120 to 248V) (Vi=248 to 372V)
2.0
0.0
0
500 1000 1500 2000 2500 3000 3500 4000
Output Current Io (mA)
Surface Temperature Increase
Surface Temperature Increase∆ T(°C)
Parameter
12-Pin input voltage
12-Pin input current
10-Pin input voltage
7-Pin input voltage
6-Pin input voltage
40
<In case of 12V output>
(Ta=25°C)
35
30
25
20
15
Vi=141V
Vi=311V
10
5
0
0 200 400 600 800 1000 1200 1400 1600 1800 2000
Output Current Io (mA)
2010.01 - Rev.A
Notice
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any
of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
R1010A