Cortex-M3/M4F Instruction Set Technical User`s Manual (Rev. A)

TE X AS INS TRUM E NTS INCO RP O R AT E D
Cortex-M3/M4F Instruction Set
T EC H N I C AL U SER ' S M AN UA L
U M-C OR E IS M - 7 7 0 3
C o p yri g h t © 2 0 10-2011
Te xa s In stru ments Inc.
Copyright
Copyright © 2010-2011 Texas Instruments Inc. All rights reserved. Stellaris and StellarisWare are registered trademarks of Texas Instruments. ARM and
Thumb are registered trademarks and Cortex is a trademark of ARM Limited. Other names and brands may be claimed as the property of others.
Texas Instruments Incorporated
108 Wild Basin, Suite 350
Austin, TX 78746
http://www.ti.com/stellaris
http://www-k.ext.ti.com/sc/technical-support/product-information-centers.htm
2
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
Table of Contents
1
Introduction ............................................................................................................ 19
1.1
1.2
1.2.1
1.2.2
1.2.3
1.2.4
1.2.5
1.2.6
1.2.7
1.2.8
Instruction Set Summary ...............................................................................................
About the Instruction Descriptions ..................................................................................
Operands .....................................................................................................................
Restrictions When Using the PC or SP ...........................................................................
Flexible Second Operand ..............................................................................................
Shift Operations ............................................................................................................
Address Alignment ........................................................................................................
PC-Relative Expressions ...............................................................................................
Conditional Execution ....................................................................................................
Instruction Width Selection .............................................................................................
2
Memory Access Instructions ................................................................................ 35
2.1
2.1.1
2.1.2
2.1.3
2.1.4
2.1.5
2.2
2.2.1
2.2.2
2.2.3
2.2.4
2.2.5
2.3
2.3.1
2.3.2
2.3.3
2.3.4
2.3.5
2.4
2.4.1
2.4.2
2.4.3
2.4.4
2.4.5
2.5
2.5.1
2.5.2
2.5.3
2.5.4
2.5.5
2.6
2.6.1
2.6.2
ADR .............................................................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition Flags .............................................................................................................
Examples .....................................................................................................................
LDR and STR (Immediate Offset) ...................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition Flags .............................................................................................................
Examples .....................................................................................................................
LDR and STR (Register Offset) ......................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition Flags .............................................................................................................
Examples .....................................................................................................................
LDR and STR (Unprivileged Access) ..............................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition Flags .............................................................................................................
Examples .....................................................................................................................
LDR (PC-Relative) ........................................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition Flags .............................................................................................................
Examples .....................................................................................................................
LDM and STM ..............................................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
November 04, 2011
19
26
27
27
27
28
31
32
32
34
36
36
36
36
36
36
37
37
38
39
39
39
40
40
41
41
41
41
42
42
43
43
43
43
44
44
44
45
45
45
46
46
47
3
Texas Instruments Incorporated
Table of Contents
2.6.3
2.6.4
2.6.5
2.6.6
2.7
2.7.1
2.7.2
2.7.3
2.7.4
2.7.5
2.8
2.8.1
2.8.2
2.8.3
2.8.4
2.8.5
2.9
2.9.1
2.9.2
2.9.3
2.9.4
Restrictions ...................................................................................................................
Condition Flags .............................................................................................................
Examples .....................................................................................................................
Incorrect Examples .......................................................................................................
PUSH and POP ............................................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition Flags .............................................................................................................
Examples .....................................................................................................................
LDREX and STREX ......................................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition Flags .............................................................................................................
Examples .....................................................................................................................
CLREX .........................................................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Condition Flags .............................................................................................................
Examples .....................................................................................................................
3
General Data Processing Instructions ................................................................. 53
3.1
3.1.1
3.1.2
3.1.3
3.1.4
3.1.5
3.1.6
3.2
3.2.1
3.2.2
3.2.3
3.2.4
3.2.5
3.3
3.3.1
3.3.2
3.3.3
3.3.4
3.3.5
3.4
3.4.1
3.4.2
3.4.3
3.4.4
3.4.5
3.5
ADD, ADC, SUB, SBC, and RSB ...................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition Flags .............................................................................................................
Examples .....................................................................................................................
Multiword Arithmetic Examples ......................................................................................
AND, ORR, EOR, BIC, and ORN ...................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition Flags .............................................................................................................
Examples .....................................................................................................................
ASR, LSL, LSR, ROR, and RRX ....................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition Flags .............................................................................................................
Examples .....................................................................................................................
CLZ ..............................................................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition Flags .............................................................................................................
Examples .....................................................................................................................
CMP and CMN ..............................................................................................................
4
47
47
47
47
48
48
48
48
49
49
50
50
50
51
51
51
52
52
52
52
52
55
55
56
56
57
57
57
58
58
58
59
59
59
60
60
62
62
62
62
63
63
63
63
63
63
64
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3.5.1
3.5.2
3.5.3
3.5.4
3.5.5
3.6
3.6.1
3.6.2
3.6.3
3.6.4
3.6.5
3.7
3.7.1
3.7.2
3.7.3
3.7.4
3.7.5
3.8
3.8.1
3.8.2
3.8.3
3.8.4
3.8.5
3.9
3.9.1
3.9.2
3.9.3
3.9.4
3.9.5
3.10
3.10.1
3.10.2
3.10.3
3.10.4
3.10.5
3.11
3.11.1
3.11.2
3.11.3
3.11.4
3.11.5
3.12
3.12.1
3.12.2
3.12.3
3.12.4
3.12.5
3.13
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition Flags .............................................................................................................
Examples .....................................................................................................................
MOV and MVN ..............................................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition Flags .............................................................................................................
Example .......................................................................................................................
MOVT ..........................................................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition Flags .............................................................................................................
Examples .....................................................................................................................
REV, REV16, REVSH, and RBIT ....................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition Flags .............................................................................................................
Examples .....................................................................................................................
SADD16 and SADD8 ....................................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition flags ..............................................................................................................
Examples .....................................................................................................................
SHADD16 and SHADD8 ................................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition flags ..............................................................................................................
Examples .....................................................................................................................
SHASX and SHSAX ......................................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition flags ..............................................................................................................
Examples .....................................................................................................................
SHSUB16 and SHSUB8 ................................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition flags ..............................................................................................................
Examples .....................................................................................................................
SSUB16 and SSUB8 .....................................................................................................
November 04, 2011
64
64
64
64
64
65
65
65
66
66
66
67
67
67
67
67
67
68
68
68
69
69
69
70
70
70
70
71
71
72
72
72
73
73
73
74
74
74
75
75
76
77
77
77
78
78
78
79
5
Texas Instruments Incorporated
Table of Contents
3.13.1
3.13.2
3.13.3
3.13.4
3.13.5
3.14
3.14.1
3.14.2
3.14.3
3.14.4
3.14.5
3.15
3.15.1
3.15.2
3.15.3
3.15.4
3.15.5
3.16
3.16.1
3.16.2
3.16.3
3.16.4
3.16.5
3.17
3.17.1
3.17.2
3.17.3
3.17.4
3.17.5
3.18
3.18.1
3.18.2
3.18.3
3.18.4
3.18.5
3.19
3.19.1
3.19.2
3.19.3
3.19.4
3.19.5
3.20
3.20.1
3.20.2
3.20.3
3.20.4
3.20.5
3.21
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition flags ..............................................................................................................
Examples .....................................................................................................................
SASX and SSAX ...........................................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition flags ..............................................................................................................
Examples .....................................................................................................................
TST and TEQ ...............................................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition Flags .............................................................................................................
Examples .....................................................................................................................
UADD16 and UADD8 ....................................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition flags ..............................................................................................................
Examples .....................................................................................................................
UASX and USAX ..........................................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition flags ..............................................................................................................
Examples .....................................................................................................................
UHADD16 and UHADD8 ...............................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition flags ..............................................................................................................
Examples .....................................................................................................................
UHASX and UHSAX ......................................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition flags ..............................................................................................................
Examples .....................................................................................................................
UHSUB16 and UHSUB8 ................................................................................................
Syntax ..........................................................................................................................
Operation .....................................................................................................................
Restrictions ...................................................................................................................
Condition flags ..............................................................................................................
Examples .....................................................................................................................
SEL ..............................................................................................................................
6
79
79
80
80
80
81
81
81
82
82
83
84
84
84
84
85
85
86
86
86
86
87
87
88
88
88
89
89
90
91
91
91
92
92
92
93
93
93
94
94
95
96
96
96
97
97
97
98
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3.21.1
3.21.2
3.21.3
3.21.4
3.21.5
3.22
3.22.1
3.22.2
3.22.3
3.22.4
3.22.5
3.23
3.23.1
3.23.2
3.23.3
3.23.4
3.23.5
3.24
3.24.1
3.24.2
3.24.3
3.24.4
3.24.5
Syntax .......................................................................................................................... 98
Operation ..................................................................................................................... 98
Restrictions ................................................................................................................... 98
Condition flags .............................................................................................................. 98
Examples ..................................................................................................................... 98
USAD8 ......................................................................................................................... 99
Syntax .......................................................................................................................... 99
Operation ..................................................................................................................... 99
Restrictions ................................................................................................................... 99
Condition flags .............................................................................................................. 99
Examples ..................................................................................................................... 99
USADA8 ..................................................................................................................... 101
Syntax ........................................................................................................................ 101
Operation ................................................................................................................... 101
Restrictions ................................................................................................................. 101
Condition flags ............................................................................................................ 101
Examples ................................................................................................................... 101
USUB16 and USUB8 ................................................................................................... 103
Syntax ........................................................................................................................ 103
Operation ................................................................................................................... 103
Restrictions ................................................................................................................. 104
Condition flags ............................................................................................................ 104
Examples ................................................................................................................... 104
4
Multiply and Divide Instructions ......................................................................... 105
4.1
4.1.1
4.1.2
4.1.3
4.1.4
4.1.5
4.2
4.2.1
4.2.2
4.2.3
4.2.4
4.2.5
4.3
4.3.1
4.3.2
4.3.3
4.3.4
4.3.5
4.4
4.4.1
4.4.2
4.4.3
4.4.4
4.4.5
MUL, MLA, and MLS ...................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition Flags ...........................................................................................................
Examples ...................................................................................................................
SMLA and SMLAW ......................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
Examples ...................................................................................................................
SMLAD .......................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
Examples ...................................................................................................................
SMLAL and SMLALD ..................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
Examples ...................................................................................................................
November 04, 2011
106
106
106
106
107
107
108
108
108
109
109
109
111
111
111
111
112
112
113
113
114
114
114
114
7
Texas Instruments Incorporated
Table of Contents
4.5
4.5.1
4.5.2
4.5.3
4.5.4
4.5.5
4.6
4.6.1
4.6.2
4.6.3
4.6.4
4.6.5
4.7
4.7.1
4.7.2
4.7.3
4.7.4
4.7.5
4.8
4.8.1
4.8.2
4.8.3
4.8.4
4.8.5
4.9
4.9.1
4.9.2
4.9.3
4.9.4
4.10
4.10.1
4.10.2
4.10.3
4.10.4
4.10.5
4.11
4.11.1
4.11.2
4.11.3
4.11.4
4.11.5
SMLSD and SMLSLD ..................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
Examples ...................................................................................................................
SMMLA and SMMLS ...................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
Examples ...................................................................................................................
SMMUL ......................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
Examples ...................................................................................................................
SMUAD and SMUSD ...................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
Examples ...................................................................................................................
SMUL and SMULW .....................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Examples ...................................................................................................................
UMULL, UMAAL, UMLAL, SMULL, and SMLAL ............................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
Examples ...................................................................................................................
SDIV and UDIV ...........................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition Flags ...........................................................................................................
Examples ...................................................................................................................
5
Saturating Instructions ........................................................................................ 131
5.1
5.1.1
5.1.2
5.1.3
5.1.4
5.1.5
SSAT and USAT ..........................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition Flags ...........................................................................................................
Examples ...................................................................................................................
8
116
116
116
117
117
117
119
119
119
120
120
120
121
121
121
121
121
122
123
123
123
124
124
124
125
125
125
126
126
128
128
128
129
129
129
130
130
130
130
130
130
132
132
132
133
133
133
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
5.2
5.2.1
5.2.2
5.2.3
5.2.4
5.2.5
5.3
5.3.1
5.3.2
5.3.3
5.3.4
5.3.5
5.4
5.4.1
5.4.2
5.4.3
5.4.4
5.4.5
5.5
5.5.1
5.5.2
5.5.3
5.5.4
5.5.5
5.6
5.6.1
5.6.2
5.6.3
5.6.4
5.6.5
5.7
5.7.1
5.7.2
5.7.3
5.7.4
5.7.5
SSAT16 and USAT16 ..................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
Examples ...................................................................................................................
QADD and QSUB ........................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
Examples ...................................................................................................................
QASX and QSAX ........................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
Examples ...................................................................................................................
QDADD and QDSUB ...................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
Examples ...................................................................................................................
UQASX and UQSAX ...................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
Examples ...................................................................................................................
UQADD and UQSUB ...................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
Examples ...................................................................................................................
6
Packing and Unpacking Instructions ................................................................. 147
6.1
6.1.1
6.1.2
6.1.3
6.1.4
6.1.5
6.2
6.2.1
6.2.2
6.2.3
6.2.4
PKHBT and PKHTB ....................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
Examples ...................................................................................................................
SXT and UXT ..............................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
November 04, 2011
134
134
134
134
135
135
136
136
136
137
137
137
138
138
138
138
139
139
140
140
140
140
141
141
142
142
142
143
143
143
144
144
144
145
145
145
148
148
148
149
149
149
150
150
151
151
151
9
Texas Instruments Incorporated
Table of Contents
6.2.5
6.3
6.3.1
6.3.2
6.3.3
6.3.4
6.3.5
6.4
6.4.1
6.4.2
6.4.3
6.4.4
6.4.5
Examples ...................................................................................................................
SXTB16 and UXTB16 ..................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
Examples ...................................................................................................................
SXTA and UXTA ..........................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
Examples ...................................................................................................................
7
Bitfield Instructions ............................................................................................. 156
7.1
7.1.1
7.1.2
7.1.3
7.1.4
7.1.5
7.2
7.2.1
7.2.2
7.2.3
7.2.4
7.2.5
BFC and BFI ...............................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition Flags ...........................................................................................................
Examples ...................................................................................................................
SBFX and UBFX .........................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition Flags ...........................................................................................................
Examples ...................................................................................................................
8
Floating-Point ....................................................................................................... 159
8.1
8.1.1
8.1.2
8.1.3
8.1.4
8.1.5
8.2
8.2.1
8.2.2
8.2.3
8.2.4
8.2.5
8.3
8.3.1
8.3.2
8.3.3
8.3.4
8.3.5
8.4
8.4.1
8.4.2
VABS .........................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
Examples ...................................................................................................................
VADD .........................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
Examples ...................................................................................................................
VCMP, VCMPE ...........................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
Examples ...................................................................................................................
VCVT, VCVTR between floating-point and integer .........................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
10
151
152
152
152
153
153
153
154
154
155
155
155
155
157
157
157
157
157
157
158
158
158
158
158
158
161
161
161
161
161
161
162
162
162
162
162
162
163
163
163
163
163
164
167
165
165
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
8.4.3
8.4.4
8.5
8.5.1
8.5.2
8.5.3
8.5.4
8.6
8.6.1
8.6.2
8.6.3
8.6.4
8.7
8.7.1
8.7.2
8.7.3
8.7.4
8.8
8.8.1
8.8.2
8.8.3
8.8.4
8.9
8.9.1
8.9.2
8.9.3
8.9.4
8.10
8.10.1
8.10.2
8.10.3
8.10.4
8.11
8.11.1
8.11.2
8.11.3
8.11.4
8.12
8.12.1
8.12.2
8.12.3
8.12.4
8.13
8.13.1
8.13.2
8.13.3
8.13.4
8.14
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VCVT between floating-point and fixed-point .................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VCVTB, VCVTT ..........................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VDIV ..........................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VFMA, VFMS ..............................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VFNMA, VFNMS .........................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VLDM .........................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VLDR .........................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VLMA, VLMS ..............................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VMOV Immediate ........................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VMOV Register ...........................................................................................................
November 04, 2011
165
166
167
167
167
168
168
169
169
169
169
170
171
171
171
171
171
172
172
172
172
172
173
173
173
173
173
174
174
174
174
175
176
176
176
177
177
178
178
178
178
178
179
179
179
179
179
180
11
Texas Instruments Incorporated
Table of Contents
8.14.1
8.14.2
8.14.3
8.14.4
8.15
8.15.1
8.15.2
8.15.3
8.15.4
8.16
8.16.1
8.16.2
8.16.3
8.16.4
8.17
8.17.1
8.17.2
8.17.3
8.17.4
8.18
8.18.1
8.18.2
8.18.3
8.18.4
8.19
8.19.1
8.19.2
8.19.3
8.19.4
8.20
8.20.1
8.20.2
8.20.3
8.20.4
8.21
8.21.1
8.21.2
8.21.3
8.21.4
8.22
8.22.1
8.22.2
8.22.3
8.22.4
8.23
8.23.1
8.23.2
8.23.3
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VMOV Scalar to ARM Core register ..............................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VMOV ARM Core register to single precision ................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VMOV Two ARM Core registers to two single precision .................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VMOV ARM Core register to scalar ..............................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VMRS ........................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VMSR ........................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VMUL .........................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VNEG .........................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VNMLA, VNMLS, VNMUL ............................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
12
180
180
180
180
181
181
181
181
181
182
182
182
182
182
183
183
183
183
183
184
184
184
184
184
185
185
185
185
185
186
186
186
186
186
187
187
187
187
187
188
188
188
188
188
189
189
189
190
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
8.23.4
8.24
8.24.1
8.24.2
8.24.3
8.24.4
8.25
8.25.1
8.25.2
8.25.3
8.25.4
8.26
8.26.1
8.26.2
8.26.3
8.26.4
8.27
8.27.1
8.27.2
8.27.3
8.27.4
8.28
8.28.1
8.28.2
8.28.3
8.28.4
8.29
8.29.1
8.29.2
8.29.3
8.29.4
8.29.5
8.29.6
8.29.7
Condition flags ............................................................................................................
VPOP .........................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VPUSH .......................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VSQRT .......................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VSTM .........................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VSTR .........................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
VSUB .........................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition flags ............................................................................................................
Operation ...................................................................................................................
Condition flags ............................................................................................................
Examples ...................................................................................................................
9
Branch and Control Instructions ........................................................................ 199
9.1
9.1.1
9.1.2
9.1.3
9.1.4
9.1.5
9.2
9.2.1
9.2.2
9.2.3
9.2.4
9.2.5
9.3
B, BL, BX, and BLX .....................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition Flags ...........................................................................................................
Examples ...................................................................................................................
CBZ and CBNZ ...........................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition Flags ...........................................................................................................
Examples ...................................................................................................................
IT ...............................................................................................................................
November 04, 2011
190
191
191
191
191
191
192
192
192
192
192
193
193
193
193
193
194
194
194
194
195
196
196
196
196
196
197
197
197
197
197
197
197
198
200
200
200
201
201
201
202
202
202
202
202
202
203
13
Texas Instruments Incorporated
Table of Contents
9.3.1
9.3.2
9.3.3
9.3.4
9.3.5
9.4
9.4.1
9.4.2
9.4.3
9.4.4
9.4.5
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition Flags ...........................................................................................................
Example .....................................................................................................................
TBB and TBH ..............................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition Flags ...........................................................................................................
Examples ...................................................................................................................
10
Miscellaneous Instructions ................................................................................. 208
10.1
10.1.1
10.1.2
10.1.3
10.1.4
10.2
10.2.1
10.2.2
10.2.3
10.2.4
10.2.5
10.3
10.3.1
10.3.2
10.3.3
10.3.4
10.4
10.4.1
10.4.2
10.4.3
10.4.4
10.5
10.5.1
10.5.2
10.5.3
10.5.4
10.6
10.6.1
10.6.2
10.6.3
10.6.4
10.6.5
10.7
10.7.1
10.7.2
10.7.3
BKPT .........................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Condition Flags ...........................................................................................................
Examples ...................................................................................................................
CPS ...........................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition Flags ...........................................................................................................
Examples ...................................................................................................................
DMB ...........................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Condition Flags ...........................................................................................................
Examples ...................................................................................................................
DSB ...........................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Condition Flags ...........................................................................................................
Examples ...................................................................................................................
ISB .............................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Condition Flags ...........................................................................................................
Examples ...................................................................................................................
MRS ...........................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
Condition Flags ...........................................................................................................
Examples ...................................................................................................................
MSR ...........................................................................................................................
Syntax ........................................................................................................................
Operation ...................................................................................................................
Restrictions .................................................................................................................
14
203
203
204
204
204
206
206
206
206
206
206
209
209
209
209
209
210
210
210
210
210
210
211
211
211
211
211
212
212
212
212
212
213
213
213
213
213
214
214
214
214
214
214
215
215
215
215
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
10.7.4 Condition Flags ...........................................................................................................
10.7.5 Examples ...................................................................................................................
10.8
NOP ...........................................................................................................................
10.8.1 Syntax ........................................................................................................................
10.8.2 Operation ...................................................................................................................
10.8.3 Condition Flags ...........................................................................................................
10.8.4 Examples ...................................................................................................................
10.9
SEV ...........................................................................................................................
10.9.1 Syntax ........................................................................................................................
10.9.2 Operation ...................................................................................................................
10.9.3 Condition Flags ...........................................................................................................
10.9.4 Examples ...................................................................................................................
10.10 SVC ...........................................................................................................................
10.10.1 Syntax ........................................................................................................................
10.10.2 Operation ...................................................................................................................
10.10.3 Condition Flags ...........................................................................................................
10.10.4 Examples ...................................................................................................................
10.11 WFE ...........................................................................................................................
10.11.1 Syntax ........................................................................................................................
10.11.2 Operation ...................................................................................................................
10.11.3 Condition Flags ...........................................................................................................
10.11.4 Examples ...................................................................................................................
10.12 WFI ............................................................................................................................
10.12.1 Syntax ........................................................................................................................
10.12.2 Operation ...................................................................................................................
10.12.3 Condition Flags ...........................................................................................................
10.12.4 Examples ...................................................................................................................
November 04, 2011
215
215
216
216
216
216
216
217
217
217
217
217
218
218
218
218
218
219
219
219
219
219
220
220
220
220
220
15
Texas Instruments Incorporated
Table of Contents
List of Figures
Figure 1-1.
Figure 1-2.
Figure 1-3.
Figure 1-4.
Figure 1-5.
Figure 1-6.
Cortex-M Extensions ...........................................................................................
ASR #3 ...............................................................................................................
LSR #3 ...............................................................................................................
LSL #3 ................................................................................................................
ROR #3 ..............................................................................................................
RRX ...................................................................................................................
16
26
29
30
30
31
31
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
List of Tables
Table 1-1.
Table 1-2.
Table 2-1.
Table 2-2.
Table 2-3.
Table 3-1.
Table 4-1.
Table 5-1.
Table 6-1.
Table 7-1.
Table 8-1.
Table 9-1.
Table 9-2.
Table 10-1.
Cortex-M3/M4F Instructions ................................................................................. 19
Condition Code Suffixes ....................................................................................... 33
Memory Access Instructions ................................................................................. 35
Offset Ranges ..................................................................................................... 38
Offset Ranges ..................................................................................................... 45
General Data Processing Instructions ................................................................... 53
Multiply and Divide Instructions ........................................................................... 105
Saturating Instructions ....................................................................................... 131
Packing and Unpacking Instructions .................................................................... 147
Bitfield Instructions ............................................................................................. 156
Floating-Point Instructions .................................................................................. 159
Branch and Control Instructions .......................................................................... 199
Branch Ranges .................................................................................................. 201
Miscellaneous Instructions ................................................................................. 208
November 04, 2011
17
Texas Instruments Incorporated
Table of Contents
List of Examples
Example 1-1.
Example 1-2.
Example 1-3.
Example 3-1.
Example 3-2.
Absolute Value ....................................................................................................
Compare and Update Value .................................................................................
Instruction Width Selection ...................................................................................
64-Bit Addition .....................................................................................................
96-Bit Subtraction ................................................................................................
18
34
34
34
57
57
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
1
Introduction
Each of the following chapters describes a functional group of Cortex-M3/M4F instructions. Together
they describe all the instructions supported by the Cortex-M3/M4F processor:
■
■
■
■
■
■
■
■
■
1.1
“Memory Access Instructions” on page 35
“General Data Processing Instructions” on page 53
“Multiply and Divide Instructions” on page 105
“Saturating Instructions” on page 131
“Packing and Unpacking Instructions” on page 147
“Bitfield Instructions” on page 156
“Floating-Point” on page 159
“Branch and Control Instructions” on page 199
“Miscellaneous Instructions” on page 208
Instruction Set Summary
The processor implements a version of the Thumb instruction set. Table 1-1 on page 19 lists the
supported instructions.
In Table 1-1 on page 19:
■ Angle brackets, <>, enclose alternative forms of the operand.
■ Braces, {}, enclose optional operands.
■ The Operands column is not exhaustive.
■ Op2 is a flexible second operand that can be either a register or a constant.
■ Most instructions can use an optional condition code suffix.
For more information on the instructions and operands, see the instruction descriptions. Figure
1-1 on page 26 shows the Cortex-M3/M4F instructions by category.
Table 1-1. Cortex-M3/M4F Instructions
M3
Operands
Brief Description
Flags
✓
M4 M4F Mnemonic
✓
✓
ADC, ADCS
{Rd,} Rn, Op2
Add with carry
N,Z,C,V
55
✓
✓
✓
ADD, ADDS
{Rd,} Rn, Op2
Add
N,Z,C,V
55
✓
✓
✓
ADD, ADDW
{Rd,} Rn, #imm12
Add
N,Z,C,V
55
✓
✓
✓
ADR
Rd, label
Load PC-relative address
-
36
✓
✓
✓
AND, ANDS
{Rd,} Rn, Op2
Logical AND
N,Z,C
58
✓
✓
✓
ASR, ASRS
Rd, Rm, <Rs|#n>
Arithmetic shift right
N,Z,C
60
✓
✓
✓
B
label
Branch
-
200
✓
✓
✓
BFC
Rd, #lsb, #width
Bit field clear
-
157
✓
✓
✓
BFI
Rd, Rn, #lsb, #width
Bit field insert
-
157
✓
✓
✓
BIC, BICS
{Rd,} Rn, Op2
Bit clear
N,Z,C
55
✓
✓
✓
BKPT
#imm
Breakpoint
-
209
✓
✓
✓
BL
label
Branch with link
-
200
✓
✓
✓
BLX
Rm
Branch indirect with link
-
200
November 04, 2011
See Page
19
Texas Instruments Incorporated
Introduction
Table 1-1. Cortex-M3/M4F Instructions (continued)
M3
M4 M4F Mnemonic
Operands
Brief Description
Flags
See Page
✓
✓
✓
BX
Rm
Branch indirect
-
200
✓
✓
✓
CBNZ
Rn, label
Compare and branch if non-zero
-
202
✓
✓
✓
CBZ
Rn, label
Compare and branch if zero
-
202
✓
✓
✓
CLREX
-
Clear exclusive
-
52
✓
✓
✓
CLZ
Rd, Rm
Count leading zeros
-
63
✓
✓
✓
CMN
Rn, Op2
Compare negative
N,Z,C,V
64
✓
✓
✓
CMP
Rn, Op2
Compare
N,Z,C,V
64
✓
✓
✓
CPSID
iflags
Change processor state, disable
interrupts
-
210
✓
✓
✓
CPSIE
iflags
Change processor state, enable
interrupts
-
210
✓
✓
✓
DMB
-
Data memory barrier
-
211
✓
✓
✓
DSB
-
Data synchronization barrier
-
211
✓
✓
✓
EOR, EORS
{Rd,} Rn, Op2
Exclusive OR
N,Z,C
55
✓
✓
✓
ISB
-
Instruction synchronization barrier -
213
✓
✓
✓
IT
-
If-Then condition block
-
203
✓
✓
✓
LDM
Rn{!}, reglist
Load multiple registers, increment after
46
✓
✓
✓
LDMDB, LDMEA
Rn{!}, reglist
Load multiple registers, decrement before
46
✓
✓
✓
LDMFD, LDMIA
Rn{!}, reglist
Load multiple registers, increment after
46
✓
✓
✓
LDR
Rt, [Rn{, #offset}]
Load register with word
-
37
✓
✓
✓
LDRB, LDRBT
Rt, [Rn{, #offset}]
Load register with byte
-
37
✓
✓
✓
LDRD
Rt, Rt2, [Rn{, #offset}]
Load register with two words
-
37
✓
✓
✓
LDREX
Rt, [Rn, #offset]
Load register exclusive
-
50
✓
✓
✓
LDREXB
Rt, [Rn]
Load register exclusive with byte
-
50
✓
✓
✓
LDREXH
Rt, [Rn]
Load register exclusive with
halfword
-
50
✓
✓
✓
LDRH, LDRHT
Rt, [Rn{, #offset}]
Load register with halfword
-
37
✓
✓
✓
LDRSB, LDRSBT
Rt, [Rn{, #offset}]
Load register with signed byte
-
37
✓
✓
✓
LDRSH, LDRSHT
Rt, [Rn{, #offset}]
Load register with signed halfword -
37
✓
✓
✓
LDRT
Rt, [Rn{, #offset}]
Load register with word
-
42
✓
✓
✓
LSL, LSLS
Rd, Rm, <Rs|#n>
Logical shift left
N,Z,C
60
✓
✓
✓
LSR, LSRS
Rd, Rm, <Rs|#n>
Logical shift right
N,Z,C
60
✓
✓
✓
MLA
Rd, Rn, Rm, Ra
Multiply with accumulate, 32-bit
result
-
106
✓
✓
✓
MLS
Rd, Rn, Rm, Ra
Multiply and subtract, 32-bit result -
106
✓
✓
✓
MOV, MOVS
Rd, Op2
Move
N,Z,C
65
✓
✓
✓
MOV, MOVW
Rd, #imm16
Move 16-bit constant
N,Z,C
65
✓
✓
MOVT
Rd, #imm16
Move top
-
67
✓
✓
MRS
Rd, spec_reg
Move from special register to
general register
-
214
✓
20
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
Table 1-1. Cortex-M3/M4F Instructions (continued)
M3
M4 M4F Mnemonic
Operands
Brief Description
Flags
See Page
✓
✓
✓
MSR
spec_reg, Rn
Move from general register to
special register
N,Z,C,V
215
✓
✓
✓
MUL, MULS
{Rd,} Rn, Rm
Multiply, 32-bit result
N,Z
106
✓
✓
✓
MVN, MVNS
Rd, Op2
Move NOT
N,Z,C
65
✓
✓
✓
NOP
-
No operation
-
216
✓
✓
✓
ORN, ORNS
{Rd,} Rn, Op2
Logical OR NOT
N,Z,C
55
✓
✓
✓
ORR, ORRS
{Rd,} Rn, Op2
Logical OR
N,Z,C
55
✓
✓
✓
PKHTB, PKHBT
{Rd,} Rn, Rm, Op2
Pack halfword
-
148
✓
✓
✓
POP
reglist
Pop registers from stack
-
48
✓
✓
✓
PUSH
reglist
Push registers onto stack
-
48
✓
✓
QADD
{Rd,} Rn, Rm
Saturating add
Q
136
✓
✓
QADD16
{Rd,} Rn, Rm
Saturating add 16
-
136
✓
✓
QADD8
{Rd,} Rn, Rm
Saturating add 8
-
136
✓
✓
QASX
{Rd,} Rn, Rm
Saturating add and subtract with
exchange
-
138
✓
✓
QDADD
{Rd,} Rn, Rm
Saturating double and add
Q
140
✓
✓
QDSUB
{Rd,} Rn, Rm
Saturating double and subtract
Q
140
✓
✓
QSAX
{Rd,} Rn, Rm
Saturating subtract and add with
exchange
-
138
✓
✓
QSUB
{Rd,} Rn, Rm
Saturating subtract
Q
136
✓
✓
QSUB16
{Rd,} Rn, Rm
Saturating subtract 16
-
136
✓
✓
QSUB8
{Rd,} Rn, Rm
Saturating subtract 8
-
136
✓
✓
✓
RBIT
Rd, Rn
Reverse bits
-
68
✓
✓
✓
REV
Rd, Rn
Reverse byte order in a word
-
68
✓
✓
✓
REV16
Rd, Rn
Reverse byte order in each halfword -
68
✓
✓
✓
REVSH
Rd, Rn
Reverse byte order in bottom
halfword and sign extend
-
68
✓
✓
✓
ROR, RORS
Rd, Rm, <Rs|#n>
Rotate right
N,Z,C
60
✓
✓
✓
RRX, RRXS
Rd, Rm
Rotate right with extend
N,Z,C
60
✓
✓
✓
RSB, RSBS
{Rd,} Rn, Op2
Reverse subtract
N,Z,C,V
55
✓
✓
SADD16
{Rd,} Rn, Rm
Signed add 16
GE
70
✓
✓
SADD8
{Rd,} Rn, Rm
Signed add 8
GE
70
✓
✓
SASX
{Rd,} Rn, Rm
Signed add and subtract with
exchange
GE
70
✓
✓
✓
SBC, SBCS
{Rd,} Rn, Op2
Subtract with carry
N,Z,C,V
55
✓
✓
✓
SBFX
Rd, Rn, #lsb, #width
Signed bit field extract
-
158
✓
✓
✓
SDIV
{Rd,} Rn, Rm
Signed divide
-
130
✓
✓
SEL
{Rd,} Rn, Rm
Select bytes
-
98
✓
✓
SEV
-
Send event
-
217
✓
✓
SHADD16
{Rd,} Rn, Rm
Signed halving add 16
-
72
✓
✓
SHADD8
{Rd,} Rn, Rm
Signed halving add 8
-
72
✓
✓
SHASX
{Rd,} Rn, Rm
Signed halving add and subtract
with exchange
-
74
✓
November 04, 2011
21
Texas Instruments Incorporated
Introduction
Table 1-1. Cortex-M3/M4F Instructions (continued)
M3
M4 M4F Mnemonic
Operands
Brief Description
Flags
See Page
✓
✓
SHSAX
{Rd,} Rn, Rm
Signed halving add and subtract
with exchange
-
74
✓
✓
SHSUB16
{Rd,} Rn, Rm
Signed halving subtract 16
-
77
✓
✓
SHSUB8
{Rd,} Rn, Rm
Signed halving subtract 8
-
77
✓
✓
SMLABB,
Rd, Rn, Rm, Ra
Signed multiply accumulate long
(halfwords)
Q
108
Rd, Rn, Rm, Ra
Signed multiply accumulate dual
Q
111
SMLABT,
SMLATB,
SMLATT
✓
✓
✓
✓
✓
SMLAL
RdLo, RdHi, Rn, Rm
Signed multiply with accumulate
(32x32+64), 64-bit result
-
128
✓
✓
✓
SMLALBB,
RdLo, RdHi, Rn, Rm
Signed multiply accumulate long
(halfwords)
-
113
SMLAD,
SMLADX
SMLALBT,
SMLALTB,
SMLALTT
✓
✓
SMLALD, SMLALDX
RdLo, RdHi, Rn, Rm
Signed multiply accumulate long
dual
-
113
✓
✓
SMLAWB,SMLAWT
Rd, Rn, Rm, Ra
Signed multiply accumulate, word Q
by halfword
108
✓
✓
SMLSD
Rd, Rn, Rm, Ra
Signed multiply subtract dual
116
RdLo, RdHi, Rn, Rm
Signed multiply subtract long dual
Q
SMLSDX
✓
✓
SMLSLD
116
SMLSLDX
✓
✓
SMMLA
Rd, Rn, Rm, Ra
Signed most significant word
multiply accumulate
-
119
✓
✓
SMMLS,
Rd, Rn, Rm, Ra
Signed most significant word
multiply subtract
-
119
SMMLR
✓
✓
SMMUL, SMMULR
{Rd,} Rn, Rm
Signed most significant word
multiply
-
121
✓
✓
SMUAD
{Rd,} Rn, Rm
Signed dual multiply add
Q
123
{Rd,} Rn, Rm
Signed multiply halfwords
-
125
SMUADX
✓
✓
SMULBB,
SMULBT,
SMULTB,
SMULTT
✓
✓
✓
SMULL
RdLo, RdHi, Rn, Rm
Signed multiply (32x32), 64-bit
result
-
128
✓
✓
SMULWB,
{Rd,} Rn, Rm
Signed multiply by halfword
-
125
✓
✓
{Rd,} Rn, Rm
Signed dual multiply subtract
-
123
SMULWT
SMUSD,
SMUSDX
✓
✓
✓
SSAT
Rd, #n, Rm {,shift #s}
Signed saturate
Q
132
✓
✓
SSAT16
Rd, #n, Rm
Signed saturate 16
Q
134
22
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
Table 1-1. Cortex-M3/M4F Instructions (continued)
M3
M4 M4F Mnemonic
Operands
Brief Description
Flags
See Page
✓
✓
SSAX
{Rd,} Rn, Rm
Saturating subtract and add with
exchange
GE
81
✓
✓
SSUB16
{Rd,} Rn, Rm
Signed subtract 16
-
79
✓
✓
SSUB8
{Rd,} Rn, Rm
Signed subtract 8
-
79
✓
✓
✓
STM
Rn{!}, reglist
Store multiple registers, increment after
46
✓
✓
✓
STMDB, STMEA
Rn{!}, reglist
Store multiple registers, decrement before
46
✓
✓
✓
STMFD, STMIA
Rn{!}, reglist
Store multiple registers, increment after
46
✓
✓
✓
STR
Rt, [Rn{, #offset}]
Store register word
-
37
✓
✓
✓
STRB, STRBT
Rt, [Rn{, #offset}]
Store register byte
-
37
✓
✓
✓
STRD
Rt, Rt2, [Rn{, #offset}]
Store register two words
-
37
✓
✓
✓
STREX
Rd, Rt, [Rn, #offset]
Store register exclusive
-
50
✓
✓
✓
STREXB
Rd, Rt, [Rn]
Store register exclusive byte
-
50
✓
✓
✓
STREXH
Rd, Rt, [Rn]
Store register exclusive halfword
-
50
✓
✓
✓
STRH, STRHT
Rt, [Rn{, #offset}]
Store register halfword
-
37
✓
✓
✓
STRSB, STRSBT
Rt, [Rn{, #offset}]
Store register signed byte
-
37
✓
✓
✓
STRSH, STRSHT
Rt, [Rn{, #offset}]
Store register signed halfword
-
37
✓
✓
✓
STRT
Rt, [Rn{, #offset}]
Store register word
-
42
✓
✓
✓
SUB, SUBS
{Rd,} Rn, Op2
Subtract
N,Z,C,V
55
✓
✓
✓
SUB, SUBW
{Rd,} Rn, #imm12
Subtract 12-bit constant
N,Z,C,V
55
✓
✓
✓
SVC
#imm
Supervisor call
-
218
✓
✓
SXTAB
{Rd,} Rn, Rm, {,ROR #}
Extend 8 bits to 32 and add
-
154
✓
✓
SXTAB16
{Rd,} Rn, Rm,{,ROR #}
Dual extend 8 bits to 16 and add
-
154
✓
✓
SXTAH
{Rd,} Rn, Rm,{,ROR #}
Extend 16 bits to 32 and add
-
154
✓
✓
SXTB16
{Rd,} Rm {,ROR #n}
Signed extend byte 16
-
150
✓
✓
✓
SXTB
{Rd,} Rm {,ROR #n}
Sign extend a byte
-
150
✓
✓
✓
SXTH
{Rd,} Rm {,ROR #n}
Sign extend a halfword
-
150
✓
✓
✓
TBB
[Rn, Rm]
Table branch byte
-
206
✓
✓
✓
TBH
[Rn, Rm, LSL #1]
Table branch halfword
-
206
✓
✓
✓
TEQ
Rn, Op2
Test equivalence
N,Z,C
84
✓
✓
✓
TST
Rn, Op2
Test
N,Z,C
84
✓
✓
UADD16
{Rd,} Rn, Rm
Unsigned add 16
GE
86
✓
✓
UADD8
{Rd,} Rn, Rm
Unsigned add 8
GE
86
✓
✓
UASX
{Rd,} Rn, Rm
Unsigned add and subtract with
exchange
GE
88
✓
✓
UHADD16
{Rd,} Rn, Rm
Unsigned halving add 16
-
91
✓
✓
UHADD8
{Rd,} Rn, Rm
Unsigned halving add 8
-
91
✓
✓
UHASX
{Rd,} Rn, Rm
Unsigned halving add and subtract with exchange
93
✓
✓
UHSAX
{Rd,} Rn, Rm
Unsigned halving subtract and add with exchange
93
November 04, 2011
23
Texas Instruments Incorporated
Introduction
Table 1-1. Cortex-M3/M4F Instructions (continued)
M3
M4 M4F Mnemonic
Operands
Brief Description
Flags
See Page
✓
✓
UHSUB16
{Rd,} Rn, Rm
Unsigned halving subtract 16
-
96
✓
✓
UHSUB8
{Rd,} Rn, Rm
Unsigned halving subtract 8
-
96
✓
✓
✓
UBFX
Rd, Rn, #lsb, #width
Unsigned bit field extract
-
158
✓
✓
✓
UDIV
{Rd,} Rn, Rm
Unsigned divide
-
130
✓
✓
UMAAL
RdLo, RdHi, Rn, Rm
Unsigned multiply accumulate
accumulate long (32x32+64), 64-bit
result
128
✓
✓
✓
UMLAL
RdLo, RdHi, Rn, Rm
Unsigned multiply with accumulate (32x32+64), 64-bit result
128
✓
✓
✓
UMULL
RdLo, RdHi, Rn, Rm
Unsigned multiply (32x32), 64-bit
result
-
128
✓
✓
UQADD16
{Rd,} Rn, Rm
Unsigned saturating add 16
-
144
✓
✓
UQADD8
{Rd,} Rn, Rm
Unsigned saturating add 8
-
144
✓
✓
UQASX
{Rd,} Rn, Rm
Unsigned saturating add and
subtract with exchange
-
142
✓
✓
UQSAX
{Rd,} Rn, Rm
Unsigned saturating subtract and
add with exchange
-
142
✓
✓
UQSUB16
{Rd,} Rn, Rm
Unsigned saturating subtract 16
-
144
✓
✓
UQSUB8
{Rd,} Rn, Rm
Unsigned saturating subtract 8
-
144
✓
✓
USAD8
{Rd,} Rn, Rm
Unsigned sum of absolute
differences
-
99
✓
✓
USADA8
{Rd,} Rn, Rm, Ra
Unsigned sum of absolute
differences and accumulate
-
101
✓
✓
USAT
Rd, #n, Rm {,shift #s}
Unsigned saturate
Q
132
✓
✓
USAT16
Rd, #n, Rm
Unsigned saturate 16
Q
134
✓
✓
USAX
{Rd,} Rn, Rm
Unsigned subtract and add with
exchange
GE
93
✓
✓
USUB16
{Rd,} Rn, Rm
Unsigned subtract 16
GE
96
✓
✓
USUB8
{Rd,} Rn, Rm
Unsigned subtract 8
GE
96
✓
✓
UXTAB
{Rd,} Rn, Rm, {,ROR #}
Rotate, extend 8 bits to 32 and add -
154
✓
✓
UXTAB16
{Rd,} Rn, Rm, {,ROR #}
Rotate, dual extend 8 bits to 16 and add
154
✓
✓
UXTAH
{Rd,} Rn, Rm, {,ROR #}
Rotate, unsigned extend and add
halfword
-
154
✓
✓
UXTB
{Rd,} Rm {,ROR #n}
Zero extend a byte
-
150
✓
✓
UXTB16
{Rd,} Rm, {,ROR #n}
Unsigned extend byte 16
-
150
✓
✓
UXTH
{Rd,} Rm {,ROR #n}
Zero extend a halfword
-
150
✓
VABS.F32
Sd, Sm
Floating-point absolute
-
161
✓
VADD.F32
{Sd,} Sn, Sm
Floating-point add
-
162
✓
VCMP.F32
Sd, <Sm | #0.0>
Compare two floating-point
registers, or one floating-point
register and zero
FPSCR
163
✓
VCMPE.F32
Sd, <Sm | #0.0>
Compare two floating-point
FPSCR
registers, or one floating-point
register and zero with extend byte
check
163
✓
✓
✓
24
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
Table 1-1. Cortex-M3/M4F Instructions (continued)
M3
M4 M4F Mnemonic
Operands
Brief Description
Flags
See Page
✓
VCVT.S32.F32
Sd, Sm
Convert between floating-point and integer
167
✓
VCVT.S16.F32
Sd, Sd, #fbits
Convert between floating-point and fixed point
167
✓
VCVTR.S32.F32
Sd, Sm
Convert between floating-point and integer with rounding
167
✓
VCVT<B|H>.F32.F16 Sd, Sm
Converts half-precision value to
single-precision
-
169
✓
VCVTT<B|T>.F32.F16 Sd, Sm
Converts single-precision register
to half-precision
-
169
✓
VDIV.F32
{Sd,} Sn, Sm
Floating-point divide
-
171
✓
VFMA.F32
{Sd,} Sn, Sm
Floating-point fused multiply
accumulate
-
172
✓
VFNMA.F32
{Sd,} Sn, Sm
Floating-point fused negate multiply accumulate
173
✓
VFMS.F32
{Sd,} Sn, Sm
Floating-point fused multiply
subtract
-
172
✓
VFNMS.F32
{Sd,} Sn, Sm
Floating-point fused negate multiply subtract
173
✓
VLDM.F<32|64>
Rn{!}, list
Load multiple extension registers
-
174
✓
VLDR.F<32|64>
<Dd|Sd>, [Rn]
Load an extension register from
memory
-
176
✓
VLMA.F32
{Sd,} Sn, Sm
Floating-point multiply accumulate -
178
✓
VLMS.F32
{Sd,} Sn, Sm
Floating-point multiply subtract
-
178
✓
VMOV.F32
Sd, #imm
Floating-point move immediate
-
179
✓
VMOV
Sd, Sm
Floating-point move register
-
180
✓
VMOV
Sn, Rt
Copy ARM core register to single
precision
-
182
✓
VMOV
Sm, Sm1, Rt, Rt2
Copy 2 ARM core registers to 2
single precision
-
183
✓
VMOV
Dd[x], Rt
Copy ARM core register to scalar
-
184
✓
VMOV
Rt, Dn[x]
Copy scalar to ARM core register
-
181
✓
VMRS
Rt, FPSCR
Move FPSCR to ARM core register N,Z,C,V
or APSR
185
✓
VMSR
FPSCR, Rt
Move to FPSCR from ARM core
register
FPSCR
186
✓
VMUL.F32
{Sd,} Sn, Sm
Floating-point multiply
-
187
✓
VNEG.F32
Sd, Sm
Floating-point negate
-
188
✓
VNMLA.F32
{Sd,} Sn, Sm
Floating-point multiply and add
-
189
✓
VNMLS.F32
{Sd,} Sn, Sm
Floating-point multiply and subtract -
189
✓
VNMUL
{Sd,} Sn, Sm
Floating-point multiply
-
189
✓
VPOP
list
Pop extension registers
-
191
✓
VPUSH
list
Push extension registers
-
192
✓
VSQRT.F32
Sd, Sm
Calculates floating-point square root -
193
✓
VSTM
Rn{!}, list
Floating-point register store multiple -
194
November 04, 2011
25
Texas Instruments Incorporated
Introduction
Table 1-1. Cortex-M3/M4F Instructions (continued)
M3
M4 M4F Mnemonic
Operands
Brief Description
Flags
See Page
✓
VSTR.F3<32|64>
Sd, [Rn]
Stores an extension register to
memory
-
194
✓
VSUB.F<32|64>
{Sd,} Sn, Sm
Floating-point subtract
-
196
✓
✓
✓
WFE
-
Wait for event
-
219
✓
✓
✓
WFI
-
Wait for interrupt
-
220
Figure 1-1. Cortex-M Extensions
1.2
About the Instruction Descriptions
The following sections give more information about using the instructions:
■
■
■
■
■
■
■
■
“Operands” on page 27
“Restrictions When Using the PC or SP” on page 27
“Flexible Second Operand” on page 27
“Shift Operations” on page 28
“Address Alignment” on page 31
“PC-Relative Expressions” on page 32
“Conditional Execution” on page 32
“Instruction Width Selection” on page 34
26
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
1.2.1
Operands
An instruction operand can be an ARM Cortex-M3/M4F register, a constant, or another
instruction-specific parameter. Instructions act on the operands and often store the result in a
destination register. When there is a destination register in the instruction, it is usually specified
before the operands.
Operands in some instructions are flexible in that they can either be a register or a constant. See
“Flexible Second Operand” on page 27.
See the Stellaris® Data Sheet for more information on the ARM Cortex-M3/M4F registers.
1.2.2
Restrictions When Using the PC or SP
Many instructions have restrictions on whether you can use the Program Counter (PC) or Stack
Pointer (SP) for the operands or destination register. See the instruction descriptions for more
information.
Important: Bit[0] of any address you write to the PC with a BX, BLX, LDM, LDR, or POP instruction
must be 1 for correct execution, because this bit indicates the required instruction set,
and the Cortex-M3/M4F processor only supports Thumb instructions.
1.2.3
Flexible Second Operand
Many general data processing instructions have a flexible second operand. This is shown as
Operand2 in the descriptions of the syntax of each instruction.
Operand2 can be a constant or a register with optional shift.
1.2.3.1
Constant
You specify an Operand2 constant in the form:
#constant
where constant can be (X and Y are hexadecimal digits):
■ Any constant that can be produced by shifting an 8-bit value left by any number of bits within a
32-bit word.
■ Any constant of the form 0x00XY00XY.
■ Any constant of the form 0xXY00XY00.
■ Any constant of the form 0xXYXYXYXY.
Note:
In the constants listed above, X and Y are hexadecimal digits.
In addition, in a small number of instructions, constant can take a wider range of values. These
are described in the individual instruction descriptions.
When an Operand2 constant is used with the instructions MOVS, MVNS, ANDS, ORRS, ORNS, EORS,
BICS, TEQ or TST, the carry flag is updated to bit[31] of the constant, if the constant is greater than
255 and can be produced by shifting an 8-bit value. These instructions do not affect the carry flag
if Operand2 is any other constant.
November 04, 2011
27
Texas Instruments Incorporated
Introduction
Your assembler might be able to produce an equivalent instruction in cases where you specify a
constant that is not permitted. For example, an assembler might assemble the instruction CMP Rd,
#0xFFFFFFFE as the equivalent instruction CMN Rd, #0x2.
1.2.3.2
Register With Optional Shift
You specify an Operand2 register in the form:
Rm {, shift}
where:
Rm
Is the register holding the data for the second operand.
shift
Is an optional shift to be applied to Rm. It can be one of:
ASR #n
Arithmetic shift right n bits, 1 ≤ n ≤ 32.
LSL #n
Logical shift left n bits, 1 ≤ n ≤ 31.
LSR #n
Logical shift right n bits, 1 ≤ n ≤ 32.
ROR #n
Rotate right n bits, 1 ≤ n ≤ 31.
RRX
Rotate right one bit, with extend.
If omitted, no shift occurs; equivalent to LSL #0.
If you omit the shift, or specify LSL #0, the instruction uses the value in Rm.
If you specify a shift, the shift is applied to the value in Rm, and the resulting 32-bit value is used
by the instruction. However, the contents in the register Rm remain unchanged. Specifying a register
with shift also updates the carry flag when used with certain instructions. For information on the shift
operations and how they affect the carry flag, see “Shift Operations” on page 28.
1.2.4
Shift Operations
Register shift operations move the bits in a register left or right by a specified number of bits, the
shift length. Register shift can be performed:
■ Directly by the instructions ASR, LSR, LSL, ROR, and RRX, and the result is written to a destination
register.
■ During the calculation of Operand2 by the instructions that specify the second operand as a
register with shift (see “Flexible Second Operand” on page 27). The result is used by the
instruction.
28
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
The permitted shift lengths depend on the shift type and the instruction (see the individual instruction
description or see “Flexible Second Operand” on page 27). If the shift length is 0, no shift occurs.
Register shift operations update the carry flag except when the specified shift length is 0. The
following sub-sections describe the various shift operations and how they affect the carry flag. In
these descriptions, Rm is the register containing the value to be shifted, and n is the shift length.
1.2.4.1
ASR
An arithmetic shift right (ASR) by n bits moves the left-hand 32-n bits of the register Rm, to the right
by n places, into the right-hand 32-n bits of the result. And it copies the original bit[31] of the register
into the left-hand n bits of the result. See Figure 1-2 on page 29.
You can use the ASR #n operation to divide the value in the register Rm by 2n, with the result being
rounded towards negative-infinity.
When the instruction is ASRS or when ASR #n is used in Operand2 with the instructions MOVS, MVNS,
ANDS, ORRS, ORNS, EORS, BICS, TEQ or TST, the carry flag is updated to the last bit shifted out,
bit[n-1], of the register Rm.
Note:
■ If n is 32 or more, then all the bits in the result are set to the value of bit[31] of Rm.
■ If n is 32 or more and the carry flag is updated, it is updated to the value of bit[31] of
Rm.
Figure 1-2. ASR #3
Carry
Flag
31
5 4 3 2 1 0
...
1.2.4.2
LSR
A logical shift right (LSR) by n bits moves the left-hand 32-n bits of the register Rm, to the right by
n places, into the right-hand 32-n bits of the result. And it sets the left-hand n bits of the result to 0.
See Figure 1-3 on page 30.
You can use the LSR #n operation to divide the value in the register Rm by 2n, if the value is regarded
as an unsigned integer.
When the instruction is LSRS or when LSR #n is used in Operand2 with the instructions MOVS, MVNS,
ANDS, ORRS, ORNS, EORS, BICS, TEQ or TST, the carry flag is updated to the last bit shifted out,
bit[n-1], of the register Rm.
Note:
■ If n is 32 or more, then all the bits in the result are cleared to 0.
■ If n is 33 or more and the carry flag is updated, it is updated to 0.
November 04, 2011
29
Texas Instruments Incorporated
Introduction
Figure 1-3. LSR #3
0
0
Carry
Flag
0
31
5 4 3 2 1 0
...
1.2.4.3
LSL
A logical shift left (LSL) by n bits moves the right-hand 32-n bits of the register Rm, to the left by n
places, into the left-hand 32-n bits of the result. And it sets the right-hand n bits of the result to 0.
See Figure 1-4 on page 30.
You can use the LSL #n operation to multiply the value in the register Rm by 2n, if the value is
regarded as an unsigned integer or a two’s complement signed integer. Overflow can occur without
warning.
When the instruction is LSLS or when LSL #n, with non-zero n, is used in Operand2 with the
instructions MOVS, MVNS, ANDS, ORRS, ORNS, EORS, BICS, TEQ or TST, the carry flag is updated to
the last bit shifted out, bit[32-n], of the register Rm. These instructions do not affect the carry flag
when used with LSL #0.
Note:
■ If n is 32 or more, then all the bits in the result are cleared to 0.
■ If n is 33 or more and the carry flag is updated, it is updated to 0.
Figure 1-4. LSL #3
0
31
Carry
Flag
1.2.4.4
0
0
5 4 3 2 1 0
...
ROR
A rotate right (ROR) by n bits moves the left-hand 32-n bits of the register Rm, to the right by n
places, into the right-hand 32-n bits of the result. And it moves the right-hand n bits of the register
into the left-hand n bits of the result. See Figure 1-5 on page 31.
When the instruction is RORS or when ROR #n is used in Operand2 with the instructions MOVS,
MVNS, ANDS, ORRS, ORNS, EORS, BICS, TEQ, or TST, the carry flag is updated to the last bit rotation,
bit[n-1], of the register Rm.
Note:
■ If n is 32, then the value of the result is the same as the value in Rm, and if the carry
flag is updated, it is updated to bit[31] of Rm.
■ ROR with shift length, n, more than 32 is the same as ROR with shift length n-32.
30
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
Figure 1-5. ROR #3
Carry
Flag
31
5 4 3 2
1 0
...
1.2.4.5
RRX
A rotate right with extend (RRX) moves the bits of the register Rm to the right by one bit. And it copies
the carry flag into bit[31] of the result. See Figure 1-6 on page 31.
When the instruction is RRXS or when RRX is used in Operand2 with the instructions MOVS, MVNS,
ANDS, ORRS, ORNS, EORS, BICS, TEQ, or TST, the carry flag is updated to bit[0] of the register Rm.
Figure 1-6. RRX
Carry
Flag
31 30
1 0
...
1.2.5
...
Address Alignment
An aligned access is an operation where a word-aligned address is used for a word, dual word, or
multiple word access, or where a halfword-aligned address is used for a halfword access. Byte
accesses are always aligned.
The Cortex-M3/M4F processors support unaligned access only for the following instructions:
■
■
■
■
■
LDR, LDRT
LDRH, LDRHT
LDRSH, LDRSHT
STR, STRT
STRH, STRHT
All other load and store instructions generate a usage fault exception if they perform an unaligned
access, and therefore their accesses must be address aligned. For more information about usage
faults, see "Fault Handling" in the Stellaris® Data Sheet.
Unaligned accesses are usually slower than aligned accesses. In addition, some memory regions
might not support unaligned accesses. Therefore, ARM recommends that programmers ensure that
accesses are aligned. To avoid accidental generation of unaligned accesses, use the UNALIGNED
bit in the Configuration and Control (CFGCTRL) register to trap all unaligned accesses (see
CFGCTRL in the Stellaris® Data Sheet).
November 04, 2011
31
Texas Instruments Incorporated
Introduction
1.2.6
PC-Relative Expressions
A PC-relative expression or label is a symbol that represents the address of an instruction or literal
data. It is represented in the instruction as the PC value plus or minus a numeric offset. The assembler
calculates the required offset from the label and the address of the current instruction. If the offset
is too big, the assembler produces an error.
Note:
■ For B, BL, CBNZ, and CBZ instructions, the value of the PC is the address of the current
instruction plus 4 bytes.
■ For all other instructions that use labels, the value of the PC is the address of the current
instruction plus 4 bytes, with bit[1] of the result cleared to 0 to make it word-aligned.
■ Your assembler might permit other syntaxes for PC-relative expressions, such as a label
plus or minus a number, or an expression of the form [PC, #number].
1.2.7
Conditional Execution
Most data processing instructions can optionally update the condition flags in the Application
Program Status Register (APSR) register according to the result of the operation (see APSR in
the Stellaris® Data Sheet). Some instructions update all flags, and some only update a subset. If a
flag is not updated, the original value is preserved. See the instruction descriptions for the flags they
affect.
You can execute an instruction conditionally, based on the condition flags set in another instruction,
either immediately after the instruction that updated the flags, or after any number of intervening
instructions that have not updated the flags.
Conditional execution is available by using conditional branches or by adding condition code suffixes
to instructions. See Table 1-2 on page 33 for a list of the suffixes to add to instructions to make
them conditional instructions. The condition code suffix enables the processor to test a condition
based on the flags. If the condition test of a conditional instruction fails, the instruction:
■ Does not execute
■ Does not write any value to its destination register
■ Does not affect any of the flags
■ Does not generate any exception
Conditional instructions, except for conditional branches, must be inside an If-Then instruction block.
See “IT” on page 203 for more information and restrictions when using the IT instruction. Depending
on the vendor, the assembler might automatically insert an IT instruction if you have conditional
instructions outside the IT block. See “IT” on page 203 for more on the IT block.
Use the CBZ and CBNZ instructions to compare the value of a register against zero and branch on
the result.
1.2.7.1
Condition Flags
The Application Program Status Register (APSR) contains the following condition flags:
■ N. Set to 1 when the result of the operation was negative; cleared to 0 otherwise.
■ Z. Set to 1 when the result of the operation was zero; cleared to 0 otherwise.
32
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
■ C. Set to 1 when the operation resulted in a carry; cleared to 0 otherwise.
■ V. Set to 1 when the operation caused overflow; cleared to 0 otherwise.
For more information about APSR, see the Stellaris® Data Sheet.
A carry occurs:
■ If the result of an addition is greater than or equal to 232
■ If the result of a subtraction is positive or zero
■ As the result of an inline barrel shifter operation in a move or logical instruction
Overflow occurs if the result of an add, subtract, or compare is greater than or equal to 231, or less
than –231.
Note:
1.2.7.2
Most instructions update the status flags only if the S suffix is specified. See the instruction
descriptions for more information.
Condition Code Suffixes
The instructions that can be conditional have an optional condition code, shown in syntax descriptions
as {cond}. Conditional execution requires a preceding IT instruction. An instruction with a condition
code is only executed if the condition code flags in APSR meet the specified condition. Table
1-2 on page 33 shows the condition codes to use.
You can use conditional execution with the IT instruction to reduce the number of branch instructions
in code.
Table 1-2 on page 33 also shows the relationship between condition code suffixes and the N, Z, C,
and V flags.
Table 1-2. Condition Code Suffixes
Suffix
Flags
Meaning
EQ
Z=1
Equal
NE
Z=0
Not equal
CS or HS
C=1
Higher or same, unsigned ≥
CC or LO
C=0
Lower, unsigned <
MI
N=1
Negative
PL
N=0
Positive or zero
VS
V=1
Overflow
VC
V=0
No overflow
HI
C = 1 and Z = 0
Higher, unsigned >
LS
C = 0 or Z = 1
Lower or same, unsigned ≤
GE
N=V
Greater than or equal, signed ≥
LT
N != V
Less than, signed <
GT
Z = 0 and N = V
Greater than, signed >
LE
Z = 1 and N != V
Less than or equal, signed ≤
AL
Can have any value
Always. This is the default when no suffix is specified.
November 04, 2011
33
Texas Instruments Incorporated
Introduction
Example 1-1, “Absolute Value” on page 34 shows the use of a conditional instruction to find the
absolute value of a number. R0 = ABS(R1).
Example 1-1. Absolute Value
MOVS
IT
RSBMI
R0, R1
MI
R0, R1, #0
; R0 = R1, setting flags.
; IT instruction for the negative condition.
; If negative, R0 = -R1.
Example 1-2, “Compare and Update Value” on page 34 shows the use of conditional instructions
to update the value of R4 if the signed value R0 is greater than R1 and R2 is greater than R3.
Example 1-2. Compare and Update Value
CMP
ITT
CMPGT
MOVGT
1.2.8
R0, R1
GT
R2, R3
R4, R5
;
;
;
;
Compare R0 and R1, setting flags
IT instruction for the two GT conditions
If 'greater than', compare R2 and R3, setting flags
If still 'greater than', do R4 = R5
Instruction Width Selection
There are many instructions that can generate either a 16-bit encoding or a 32-bit encoding depending
on the operands and destination register specified. For some of these instructions, you can force a
specific instruction size by using an instruction width suffix. The .W suffix forces a 32-bit instruction
encoding. The .N suffix forces a 16-bit instruction encoding.
If you specify an instruction width suffix and the assembler cannot generate an instruction encoding
of the requested width, it generates an error.
Note:
In some cases it might be necessary to specify the .W suffix, for example if the operand is
the label of an instruction or literal data, as in the case of branch instructions. This is because
the assembler might not automatically generate the right size encoding.
To use an instruction width suffix, place it immediately after the instruction mnemonic and condition
code, if any. Example 1-3, “Instruction Width Selection” on page 34 shows instructions with the
instruction width suffix.
Example 1-3. Instruction Width Selection
BCS.W
label
; creates a 32-bit instruction even for a short branch
ADDS.W R0, R0, R1 ; creates a 32-bit instruction even though the same
; operation can be done by a 16-bit instruction
34
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
2
Memory Access Instructions
Table 2-1 on page 35 shows the memory access instructions:
Table 2-1. Memory Access Instructions
Mnemonic
Brief Description
ADR
Load PC-relative address
36
CLREX
Clear exclusive
52
LDM{mode}
Load multiple registers
46
LDR{type}
Load register using immediate offset
37
LDR{type}
Load register using register offset
40
LDR{type}T
Load register with unprivileged access
42
LDR{type}
Load register using PC-relative address
44
LDRD
Load register using PC-relative address (two words)
44
LDREX{type}
Load register exclusive
50
POP
Pop registers from stack
48
PUSH
Push registers onto stack
48
STM{mode}
Store multiple registers
46
STR{type}
Store register using immediate offset
37
STR{type}
Store register using register offset
40
STR{type}T
Store register with unprivileged access
42
STREX{type}
Store register exclusive
50
November 04, 2011
See Page
35
Texas Instruments Incorporated
Memory Access Instructions
2.1
ADR
Generate PC-relative address.
Applies to...
2.1.1
M3
M4
M4F
✓
✓
✓
Syntax
ADR{cond} Rd, label
where:
cond
Is an optional condition code. See Table 1-2 on page 33.
Rd
Is the destination register.
label
Is a PC-relative expression. See “PC-Relative Expressions” on page 32.
2.1.2
Operation
ADR determines the address by adding an immediate value to the PC, and writes the result to the
destination register.
ADR produces position-independent code, because the address is PC-relative.
If you use ADR to generate a target address for a BX or BLX instruction, you must ensure that bit[0]
of the address you generate is set to 1 for correct execution.
Values of label must be within the range of −4095 to +4095 from the address in the PC.
Note:
2.1.3
You might have to use the .W suffix to get the maximum offset range or to generate
addresses that are not word-aligned. See “Instruction Width Selection” on page 34.
Restrictions
Rd must not be SP and must not be PC.
2.1.4
Condition Flags
This instruction does not change the flags.
2.1.5
Examples
ADR
R1, TextMessage
; Write address value of a location labeled as
; TextMessage to R1.
36
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
2.2
LDR and STR (Immediate Offset)
Load and Store with immediate offset, pre-indexed immediate offset, or post-indexed immediate
offset.
Applies to...
2.2.1
M3
M4
M4F
✓
✓
✓
Syntax
op{type}{cond} Rt, [Rn {, #offset}]
; immediate offset
op{type}{cond} Rt, [Rn, #offset]!
; pre-indexed
op{type}{cond} Rt, [Rn], #offset
; post-indexed
opD{cond} Rt, Rt2, [Rn {, #offset}]
; immediate offset, two words
opD{cond} Rt, Rt2, [Rn, #offset]!
; pre-indexed, two words
opD{cond} Rt, Rt2, [Rn], #offset
; post-indexed, two words
where:
op
Is one of:
LDR
Load Register.
STR
Store Register.
type
Is one of:
B
Unsigned byte, zero extend to 32 bits on loads.
SB
Signed byte, sign extend to 32 bits (LDR only).
H
Unsigned halfword, zero extend to 32 bits on loads.
SH
Signed halfword, sign extend to 32 bits (LDR only).
Omit, for word.
cond
Is an optional condition code. See Table 1-2 on page 33.
November 04, 2011
37
Texas Instruments Incorporated
Memory Access Instructions
Rt
Is the register to load or store.
Rn
Is the register on which the memory address is based.
offset
Is an offset from Rn. If offset is omitted, the address is the contents of Rn.
Rt2
Is the additional register to load or store for two-word operations.
2.2.2
Operation
LDR instructions load one or two registers with a value from memory.
STR instructions store one or two register values to memory.
Load and store instructions with immediate offset can use the following addressing modes:
Offset addressing
The offset value is added to or subtracted from the address obtained from the register Rn. The
result is used as the address for the memory access. The register Rn is unaltered. The assembly
language syntax for this mode is:
[Rn, #offset]
Pre-indexed addressing
The offset value is added to or subtracted from the address obtained from the register Rn. The
result is used as the address for the memory access and written back into the register Rn. The
assembly language syntax for this mode is:
[Rn, #offset]!
Post-indexed addressing
The address obtained from the register Rn is used as the address for the memory access. The
offset value is added to or subtracted from the address, and written back into the register Rn.
The assembly language syntax for this mode is:
[Rn], #offset
The value to load or store can be a byte, halfword, word, or two words. Bytes and halfwords can
either be signed or unsigned. See “Address Alignment” on page 31.
Table 2-2 on page 38 shows the ranges of offset for immediate, pre-indexed and post-indexed
forms.
Table 2-2. Offset Ranges
Instruction Type
Pre-Indexed
Post-Indexed
Word, halfword, signed halfword, −255 to 4095
byte, or signed byte
Immediate Offset
−255 to 255
−255 to 255
Two words
Multiple of 4 in the range
−1020 to 1020
Multiple of 4 in the range
−1020 to 1020
Multiple of 4 in the range
−1020 to 1020
38
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
2.2.3
Restrictions
For load instructions:
■ Rt can be SP or PC for word loads only.
■ Rt must be different from Rt2 for two-word loads.
■ Rn must be different from Rt and Rt2 in the pre-indexed or post-indexed forms.
When Rt is PC in a word load instruction:
■ Bit[0] of the loaded value must be 1 for correct execution.
■ A branch occurs to the address created by changing bit[0] of the loaded value to 0.
■ If the instruction is conditional, it must be the last instruction in the IT block.
For store instructions:
■ Rt can be SP for word stores only.
■ Rt must not be PC.
■ Rn must not be PC.
■ Rn must be different from Rt and Rt2 in the pre-indexed or post-indexed forms.
2.2.4
Condition Flags
These instructions do not change the flags.
2.2.5
Examples
LDR
LDRNE
R8, [R10]
R2, [R5, #960]!
STR
R2, [R9,#const-struc]
STRH
R3, [R4], #4
LDRD
R8, R9, [R3, #0x20]
STRD
R0, R1, [R8], #-16
;
;
;
;
;
;
;
;
;
;
;
;
;
;
Loads R8 from the address in R10.
Loads (conditionally) R2 from a word
960 bytes above the address in R5, and
increments R5 by 960.
const-struc is an expression evaluating
to a constant in the range 0-4095.
Store R3 as halfword data into address in
R4, then increment R4 by 4.
Load R8 from a word 32 bytes above the
address in R3, and load R9 from a word 36
bytes above the address in R3.
Store R0 to address in R8, and store R1 to
a word 4 bytes above the address in R8,
and then decrement R8 by 16.
November 04, 2011
39
Texas Instruments Incorporated
Memory Access Instructions
2.3
LDR and STR (Register Offset)
Load and Store with register offset.
Applies to...
2.3.1
M3
M4
M4F
✓
✓
✓
Syntax
op{type}{cond} Rt, [Rn, Rm {, LSL #n}]
where:
op
Is one of:
LDR
Load Register.
STR
Store Register.
type
Is one of:
B
Unsigned byte, zero extend to 32 bits on loads.
SB
Signed byte, sign extend to 32 bits (LDR only).
H
Unsigned halfword, zero extend to 32 bits on loads.
SH
Signed halfword, sign extend to 32 bits (LDR only).
Omit, for word.
cond
Is an optional condition code. See Table 1-2 on page 33.
Rt
Is the register to load or store.
Rn
Is the register on which the memory address is based.
Rm
Is a register containing a value to be used as the offset.
LSL #n
Is an optional shift, with n in the range 0 to 3.
40
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
2.3.2
Operation
LDR instructions load a register with a value from memory.
STR instructions store a register value into memory.
The memory address to load from or store to is at an offset from the register Rn. The offset is
specified by the register Rm and can be shifted left by up to 3 bits using LSL.
The value to load or store can be a byte, halfword, or word. For load instructions, bytes and halfwords
can either be signed or unsigned. See “Address Alignment” on page 31.
2.3.3
Restrictions
In these instructions:
■ Rn must not be PC.
■ Rm must not be SP and must not be PC.
■ Rt can be SP only for word loads and word stores.
■ Rt can be PC only for word loads.
When Rt is PC in a word load instruction:
■ Bit[0] of the loaded value must be 1 for correct execution, and a branch occurs to this
halfword-aligned address.
■ If the instruction is conditional, it must be the last instruction in the IT block.
2.3.4
Condition Flags
These instructions do not change the flags.
2.3.5
Examples
STR
LDRSB
STR
R0, [R5, R1]
;
;
R0, [R5, R1, LSL #1] ;
;
;
R0, [R1, R2, LSL #2] ;
;
Store value of R0 into an address equal to
sum of R5 and R1.
Read byte value from an address equal to
sum of R5 and two times R1, sign extend it
to a word value and put it in R0.
Store R0 to an address equal to sum of R1
and four times R2.
November 04, 2011
41
Texas Instruments Incorporated
Memory Access Instructions
2.4
LDR and STR (Unprivileged Access)
Load and Store with unprivileged access.
Applies to...
2.4.1
M3
M4
M4F
✓
✓
✓
Syntax
op{type}T{cond} Rt, [Rn {, #offset}]
; immediate offset
where:
op
Is one of:
LDR
Load Register.
STR
Store Register.
type
Is one of:
B
Unsigned byte, zero extend to 32 bits on loads.
SB
Signed byte, sign extend to 32 bits (LDR only).
H
Unsigned halfword, zero extend to 32 bits on loads.
SH
Signed halfword, sign extend to 32 bits (LDR only).
Omit, for word.
cond
Is an optional condition code. See Table 1-2 on page 33.
Rt
Is the register to load or store.
Rn
Is the register on which the memory address is based.
offset
Is an offset from Rn and can be 0 to 255. If offset is omitted, the address is the value in Rn.
42
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
2.4.2
Operation
These load and store instructions perform the same function as the memory access instructions
with immediate offset (see “LDR and STR (Immediate Offset)” on page 37). The difference is that
these instructions have only unprivileged access even when used in privileged software.
When used in unprivileged software, these instructions behave in exactly the same way as normal
memory access instructions with immediate offset.
2.4.3
Restrictions
In these instructions:
■ Rn must not be PC.
■ Rt must not be SP and must not be PC.
2.4.4
Condition Flags
These instructions do not change the flags.
2.4.5
Examples
STRBTEQ
R4, [R7]
LDRHT
R2, [R2, #8]
;
;
;
;
Conditionally store least significant byte in
R4 to an address in R7, with unprivileged access.
Load halfword value from an address equal to
sum of R2 and 8 into R2, with unprivileged access.
November 04, 2011
43
Texas Instruments Incorporated
Memory Access Instructions
2.5
LDR (PC-Relative)
Load register from memory.
Applies to...
2.5.1
M3
M4
M4F
✓
✓
✓
Syntax
LDR{type}{cond} Rt, label
LDRD{cond} Rt, Rt2, label
; Load two words
where:
type
Is one of:
B
Unsigned byte, zero extend to 32 bits.
SB
Signed byte, sign extend to 32 bits.
H
Unsigned halfword, zero extend to 32 bits.
SH
Signed halfword, sign extend to 32 bits.
Omit, for word.
cond
Is an optional condition code. See Table 1-2 on page 33.
Rt
Is the register to load or store.
Rt2
Is the second register to load or store.
label
Is a PC-relative expression. See “PC-Relative Expressions” on page 32.
2.5.2
Operation
LDR loads a register with a value from a PC-relative memory address. The memory address is
specified by a label or by an offset from the PC.
The value to load or store can be a byte, halfword, or word. For load instructions, bytes and halfwords
can either be signed or unsigned. See “Address Alignment” on page 31.
label must be within a limited range of the current instruction. Table 2-3 on page 45 shows the
possible offsets between label and the PC.
44
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
Table 2-3. Offset Ranges
a
Instruction Type
Offset Range
Word, halfword, signed halfword, byte, signed byte
−4095 to 4095
Two words
−1020 to 1020
a. You might have to use the .W suffix to get the maximum offset range. See “Instruction Width Selection” on page 34.
2.5.3
Restrictions
In these instructions:
■ Rt can be SP or PC only for word loads.
■ Rt2 must not be SP and must not be PC.
■ Rt must be different from Rt2.
When Rt is PC in a word load instruction:
■ Bit[0] of the loaded value must be 1 for correct execution, and a branch occurs to this
halfword-aligned address.
■ If the instruction is conditional, it must be the last instruction in the IT block.
2.5.4
Condition Flags
These instructions do not change the flags.
2.5.5
Examples
LDR
R0, LookUpTable
LDRSB
R7, localdata
;
;
;
;
;
Load R0 with a word of data from an address
labeled as LookUpTable.
Load a byte value from an address labeled
as localdata, sign extend it to a word
value, and put it in R7.
November 04, 2011
45
Texas Instruments Incorporated
Memory Access Instructions
2.6
LDM and STM
Load and Store Multiple registers.
Applies to...
2.6.1
M3
M4
M4F
✓
✓
✓
Syntax
op{addr_mode}{cond} Rn{!}, reglist
where:
op
Is one of:
LDM
Load Multiple registers.
STM
Store Multiple registers.
addr_mode
Is any one of the following:
IA
Increment address After each access. This is the default.
DB
Decrement address Before each access.
cond
Is an optional condition code. See Table 1-2 on page 33.
Rn
Is the register on which the memory addresses are based.
!
Is an optional writeback suffix. If ! is present then the final address, that is loaded from or stored
to, is written back into Rn.
reglist
Is a list of one or more registers to be loaded or stored, enclosed in braces. It can contain register
ranges. It must be comma separated if it contains more than one register or register range. See
47.
LDM and LDMFD are synonyms for LDMIA. LDMFD refers to its use for popping data from Full
Descending stacks.
LDMEA is a synonym for LDMDB, and refers to its use for popping data from Empty Ascending stacks.
STM and STMEA are synonyms for STMIA. STMEA refers to its use for pushing data onto Empty
Ascending stacks.
STMFD is s synonym for STMDB, and refers to its use for pushing data onto Full Descending stacks
46
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
2.6.2
Operation
LDM instructions load the registers in reglist with word values from memory addresses based on
Rn.
STM instructions store the word values in the registers in reglist to memory addresses based on Rn.
For LDM, LDMIA, LDMFD, STM, STMIA, and STMEA, the memory addresses used for the accesses
are at 4-byte intervals ranging from Rn to Rn + 4 * (n-1), where n is the number of registers in reglist.
The accesses happen in order of increasing register numbers, with the lowest numbered register
using the lowest memory address and the highest number register using the highest memory address.
If the writeback suffix is specified, the value of Rn + 4 * (n-1) is written back to Rn.
For LDMDB, LDMEA, STMDB, and STMFD, the memory addresses used for the accesses are at 4-byte
intervals ranging from Rn to Rn - 4 * (n-1), where n is the number of registers in reglist. The accesses
happen in order of decreasing register numbers, with the highest numbered register using the highest
memory address and the lowest number register using the lowest memory address. If the writeback
suffix is specified, the value of Rn - 4 * (n-1) is written back to Rn.
The PUSH and POP instructions can be expressed in this form. See “PUSH and POP” on page 48
for details.
2.6.3
Restrictions
In these instructions:
■ Rn must not be PC.
■ reglist must not contain SP.
■ In any STM instruction, reglist must not contain PC.
■ In any LDM instruction, reglist must not contain PC if it contains LR.
■ reglist must not contain Rn if you specify the writeback suffix.
When PC is in reglist in an LDM instruction:
■ Bit[0] of the value loaded to the PC must be 1 for correct execution, and a branch occurs to this
halfword-aligned address.
■ If the instruction is conditional, it must be the last instruction in the IT block.
2.6.4
Condition Flags
These instructions do not change the flags.
2.6.5
Examples
LDM
STMDB
2.6.6
R8,{R0,R2,R9}
; LDMIA is a synonym for LDM.
R1!,{R3-R6,R11,R12}
Incorrect Examples
STM
LDM
R5!,{R5,R4,R9} ; Value stored for R5 is unpredictable.
R2, {}
; There must be at least one register in the list.
November 04, 2011
47
Texas Instruments Incorporated
Memory Access Instructions
2.7
PUSH and POP
Push registers on and pop registers off a full-descending stack.
Applies to...
2.7.1
M3
M4
M4F
✓
✓
✓
Syntax
PUSH{cond} reglist
POP{cond} reglist
where:
cond
Is an optional condition code. See Table 1-2 on page 33.
reglist
Is a non-empty list of registers, enclosed in braces. It can contain register ranges. It must be
comma separated if it contains more than one register or register range.
PUSH and POP are synonyms for STMDB and LDM (or LDMIA) with the memory addresses for the
access based on SP, and with the final address for the access written back to the SP. PUSH and
POP are the preferred mnemonics in these cases.
2.7.2
Operation
PUSH stores registers on the stack in order of decreasing register numbers, with the highest numbered
register using the highest memory address and the lowest numbered register using the lowest
memory address.
POP loads registers from the stack in order of increasing register numbers, with the lowest numbered
register using the lowest memory address and the highest numbered register using the highest
memory address.
See “LDM and STM” on page 46 for more information.
2.7.3
Restrictions
In these instructions:
■ reglist must not contain SP.
■ For the PUSH instruction, reglist must not contain PC.
■ For the POP instruction, reglist must not contain PC if it contains LR.
When PC is in reglist in a POP instruction:
■ Bit[0] of the value loaded to the PC must be 1 for correct execution, and a branch occurs to this
halfword-aligned address.
■ If the instruction is conditional, it must be the last instruction in the IT block.
48
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
2.7.4
Condition Flags
These instructions do not change the flags.
2.7.5
Examples
PUSH
PUSH
POP
{R0,R4-R7}
{R2,LR}
{R0,R10,PC}
November 04, 2011
49
Texas Instruments Incorporated
Memory Access Instructions
2.8
LDREX and STREX
Load and Store Register Exclusive.
Applies to...
2.8.1
M3
M4
M4F
✓
✓
✓
Syntax
LDREX{cond} Rt, [Rn {, #offset}]
STREX{cond} Rd, Rt, [Rn {, #offset}]
LDREXB{cond} Rt, [Rn]
STREXB{cond} Rd, Rt, [Rn]
LDREXH{cond} Rt, [Rn]
STREXH{cond} Rd, Rt, [Rn]
where:
cond
Is an optional condition code. See Table 1-2 on page 33.
Rd
Is the destination register for the returned status.
Rt
Is the register to load or store.
Rn
Is the register on which the memory address is based.
offset
Is an optional offset applied to the value in Rn. If offset is omitted, the address is the value
in Rn.
2.8.2
Operation
LDREX, LDREXB, and LDREXH load a word, byte, and halfword respectively from a memory address.
STREX, STREXB, and STREXH attempt to store a word, byte, and halfword respectively to a memory
address. The address used in any Store-Exclusive instruction must be the same as the address in
the most recently executed Load-exclusive instruction. The value stored by the Store-Exclusive
instruction must also have the same data size as the value loaded by the preceding Load-exclusive
instruction. This means software must always use a Load-exclusive instruction and a matching
Store-Exclusive instruction to perform a synchronization operation (see "Synchronization Primitives"
in the Stellaris® Data Sheet).
If a Store-Exclusive instruction performs the store, it writes 0 to its destination register. If it does not
perform the store, it writes 1 to its destination register. If the Store-Exclusive instruction writes 0 to
the destination register, it is guaranteed that no other process in the system has accessed the
memory location between the Load-exclusive and Store-Exclusive instructions.
50
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
For reasons of performance, keep the number of instructions between corresponding Load-Exclusive
and Store-Exclusive instruction to a minimum.
Important: The result of executing a Store-Exclusive instruction to an address that is different from
that used in the preceding Load-Exclusive instruction is unpredictable.
2.8.3
Restrictions
In these instructions:
■ Do not use PC.
■ Do not use SP for Rd and Rt.
■ For STREX, Rd must be different from both Rt and Rn.
■ The value of offset must be a multiple of four in the range 0-1020.
2.8.4
Condition Flags
These instructions do not change the flags.
2.8.5
Examples
MOV
try
LDREX
CMP
ITT
STREXEQ
CMPEQ
BNE
....
R1, #0x1
; Initialize the ‘lock taken’ value.
R0,
R0,
EQ
R0,
R0,
try
;
;
;
;
;
;
;
[LockAddr]
#0
R1, [LockAddr]
#0
Load the lock value.
Is the lock free?
IT instruction for STREXEQ and CMPEQ.
Try and claim the lock.
Did this succeed?
No – try again.
Yes – we have the lock.
November 04, 2011
51
Texas Instruments Incorporated
Memory Access Instructions
2.9
CLREX
Clear Exclusive.
Applies to...
2.9.1
M3
M4
M4F
✓
✓
✓
Syntax
CLREX{cond}
where:
cond
Is an optional condition code. See Table 1-2 on page 33.
2.9.2
Operation
Use CLREX to make the next STREX, STREXB, or STREXH instruction write 1 to its destination register
and fail to perform the store. It is useful in exception handler code to force the failure of the store
exclusive if the exception occurs between a load exclusive instruction and the matching store
exclusive instruction in a synchronization operation (see "Synchronization Primitives" in the Stellaris®
Data Sheet).
2.9.3
Condition Flags
This instruction does not change the flags.
2.9.4
Examples
CLREX
52
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3
General Data Processing Instructions
Table 3-1 on page 53 shows the data processing instructions:
Table 3-1. General Data Processing Instructions
Mnemonic
Brief Description
ADC
Add with carry
55
ADD
Add
55
ADDW
Add
55
AND
Logical AND
58
ASR
Arithmetic shift right
60
BIC
Bit clear
58
CLZ
Count leading zeros
63
CMN
Compare negative
64
CMP
Compare
64
EOR
Exclusive OR
58
LSL
Logical shift left
60
LSR
Logical shift right
60
MOV
Move
65
MOVT
Move top
67
MOVW
Move 16-bit constant
65
MVN
Move NOT
65
ORN
Logical OR NOT
58
ORR
Logical OR
58
RBIT
Reverse bits
68
REV
Reverse byte order in a word
68
REV16
Reverse byte order in each halfword
68
REVSH
Reverse byte order in bottom halfword and sign extend
68
ROR
Rotate right
60
RRX
Rotate right with extend
60
RSB
Reverse subtract
55
SADD16
Signed add 16
70
SADD8
Signed add 8
70
SASX
Signed add and subtract with exchange
81
SSAX
Signed subtract and add with exchange
81
SBC
Subtract with carry
55
SEL
Select bytes
98
SHADD16
Signed halving add 16
72
SHADD8
Signed halving add 8
72
SHASX
Signed halving add and subtract with exchange
74
SHSAX
Signed halving subtract and add with exchange
74
SHSUB16
Signed halving subtract 16
77
SHSUB8
Signed halving subtract 8
77
November 04, 2011
See Page
53
Texas Instruments Incorporated
General Data Processing Instructions
Table 3-1. General Data Processing Instructions (continued)
Mnemonic
Brief Description
See Page
SSUB16
Signed subtract 16
79
SSUB8
Signed subtract 8
79
SUB
Subtract
55
SUBW
Subtract
55
TEQ
Test equivalence
84
TST
Test
84
UADD16
Unsigned add 16
86
UADD8
Unsigned add 8
86
UASX
Unsigned add and subtract with exchange
88
USAX
Unsigned subtract and add with exchange
88
UHADD16
Unsigned halving add 16
91
UHADD8
Unsigned halving add 8
91
UHASX
Unsigned halving add and subtract with exchange
93
UHSAX
Unsigned halving subtract and add with exchange
93
UHSUB16
Unsigned halving subtract 16
96
UHSUB8
Unsigned halving subtract 8
96
USAD8
Unsigned sum of absolute differences
99
USADA8
Unsigned sum of absolute differences and accumulate
101
USUB16
Unsigned subtract 16
103
USUB8
Unsigned subtract 8
103
54
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3.1
ADD, ADC, SUB, SBC, and RSB
Add, Add with carry, Subtract, Subtract with carry, and Reverse Subtract.
Applies to...
3.1.1
M3
M4
M4F
✓
✓
✓
Syntax
op{S}{cond} {Rd,} Rn, Operand2
op{cond} {Rd,} Rn, #imm12
; ADD and SUB only
where:
op
Is one of:
ADD
Add.
ADC
Add with Carry.
SUB
Subtract.
SBC
Subtract with Carry.
RSB
Reverse Subtract.
S
Is an optional suffix. If S is specified, the condition code flags are updated on the result of the
operation. See 32.
cond
Is an optional condition code. See Table 1-2 on page 33.
Rd
Is the destination register. If Rd is omitted, the destination register is Rn.
Rn
Is the register holding the first operand.
Operand2
Is a flexible second operand. See “Flexible Second Operand” on page 27 for details of the
options.
imm12
Is any value in the range 0-4095.
November 04, 2011
55
Texas Instruments Incorporated
General Data Processing Instructions
3.1.2
Operation
The ADD instruction adds the value of Operand2 or imm12 to the value in Rn.
The ADC instruction adds the values in Rn and Operand2, together with the carry flag.
The SUB instruction subtracts the value of Operand2 or imm12 from the value in Rn.
The SBC instruction subtracts the value of Operand2 from the value in Rn. If the carry flag is clear,
the result is reduced by one.
The RSB instruction subtracts the value in Rn from the value of Operand2. This is useful because
of the wide range of options for Operand2.
Use ADC and SBC to synthesize multiword arithmetic. See 57.
See also 36.
Note:
3.1.3
ADDW is equivalent to the ADD syntax that uses the imm12 operand. SUBW is equivalent to
the SUB syntax that uses the imm12 operand.
Restrictions
In these instructions:
■ Operand2 must not be SP and must not be PC.
■ Rd can be SP only in ADD and SUB, and only with the additional restrictions:
– Rn must also be SP.
– any shift in Operand2 must be limited to a maximum of 3 bits using LSL.
■ Rn can be SP only in ADD and SUB.
■ Rd can be PC only in the ADD{cond} PC, PC, Rm instruction where:
– You must not specify the S suffix.
– Rm must not be PC and must not be SP.
– If the instruction is conditional, it must be the last instruction in the IT block.
■ With the exception of the ADD{cond} PC, PC, Rm instruction, Rn can be PC only in ADD and
SUB, and only with the additional restrictions:
– You must not specify the S suffix.
– The second operand must be a constant in the range 0 to 4095.
Note:
– When using the PC for an addition or a subtraction, bits[1:0] of the PC are rounded
to b00 before performing the calculation, making the base address for the calculation
word-aligned.
– If you want to generate the address of an instruction, you have to adjust the constant
based on the value of the PC. ARM recommends that you use the ADR instruction
instead of ADD or SUB with Rn equal to the PC, because your assembler automatically
calculates the correct constant for the ADR instruction.
56
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
When Rd is PC in the ADD{cond} PC, PC, Rm instruction:
■ Bit[0] of the value written to the PC is ignored
■ A branch occurs to the address created by forcing bit[0] of that value to 0.
3.1.4
Condition Flags
If S is specified, these instructions update the N, Z, C and V flags according to the result.
3.1.5
Examples
ADD
SUBS
RSB
ADCHI
3.1.6
R2, R1, R3
R8, R6, #240
R4, R4, #1280
R11, R0, R3
;
;
;
;
Sets the flags on the result.
Subtracts contents of R4 from 1280.
Only executed if C flag set and Z
flag clear.
Multiword Arithmetic Examples
Example 3-1, “64-Bit Addition” on page 57 shows two instructions that add a 64-bit integer contained
in R2 and R3 to another 64-bit integer contained in R0 and R1, and place the result in R4 and R5.
Example 3-1. 64-Bit Addition
ADDS
ADC
R4, R0, R2
R5, R1, R3
; Add the least significant words.
; Add the most significant words with carry.
Multiword values do not have to use consecutive registers. Example 3-2, “96-Bit
Subtraction” on page 57 shows instructions that subtract a 96-bit integer contained in R9, R1, and
R11 from another contained in R6, R2, and R8. The example stores the result in R6, R9, and R2.
Example 3-2. 96-Bit Subtraction
SUBS
SBCS
SBC
R6, R6, R9
R9, R2, R1
R2, R8, R11
; Subtract the least significant words.
; Subtract the middle words with carry.
; Subtract the most significant words with carry.
November 04, 2011
57
Texas Instruments Incorporated
General Data Processing Instructions
3.2
AND, ORR, EOR, BIC, and ORN
Logical AND, OR, Exclusive OR, Bit Clear, and OR NOT.
Applies to...
3.2.1
M3
M4
M4F
✓
✓
✓
Syntax
op{S}{cond} {Rd,} Rn, Operand2
where:
op
Is one of:
AND
Logical AND.
ORR
Logical OR, or bit set.
EOR
Logical Exclusive OR.
BIC
Logical AND NOT, or bit clear.
ORN
Logical OR NOT.
S
Is an optional suffix. If S is specified, the condition code flags are updated on the result of the
operation. See 32.
cond
Is an optional condition code. See Table 1-2 on page 33.
Rd
Is the destination register.
Rn
Is the register holding the first operand.
Operand2
Is a flexible second operand. See “Flexible Second Operand” on page 27 for details of the
options.
3.2.2
Operation
The AND, EOR, and ORR instructions perform bitwise AND, Exclusive OR, and OR operations on the
values in Rn and Operand2.
The BIC instruction performs an AND operation on the bits in Rn with the complements of the
corresponding bits in the value of Operand2.
58
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
The ORN instruction performs an OR operation on the bits in Rn with the complements of the
corresponding bits in the value of Operand2.
3.2.3
Restrictions
Do not use SP and do not use PC.
3.2.4
Condition Flags
If S is specified, these instructions:
■ Update the N and Z flags according to the result.
■ Can update the C flag during the calculation of Operand2. See “Flexible Second
Operand” on page 27.
■ Do not affect the V flag.
3.2.5
Examples
AND
ORREQ
ANDS
EORS
BIC
ORN
ORNS
R9,
R2,
R9,
R7,
R0,
R7,
R7,
R2, #0xFF00
R0, R5
R8, #0x19
R11, #0x18181818
R1, #0xab
R11, R14, ROR #4
R11, R14, ASR #32
November 04, 2011
59
Texas Instruments Incorporated
General Data Processing Instructions
3.3
ASR, LSL, LSR, ROR, and RRX
Arithmetic Shift Right, Logical Shift Left, Logical Shift Right, Rotate Right, and Rotate Right with
Extend.
Applies to...
3.3.1
M3
M4
M4F
✓
✓
✓
Syntax
op{S}{cond} Rd, Rm, Rs
op{S}{cond} Rd, Rm, #n
RRX{S}{cond} Rd, Rm
where:
op
Is one of:
ASR
Arithmetic Shift Right.
LSL
Logical Shift Left.
LSR
Logical Shift Right.
ROR
Rotate Right.
S
Is an optional suffix. If S is specified, the condition code flags are updated on the result of the
operation. See 32.
Rd
Is the destination register.
Rm
Is the register holding the value to be shifted.
Rs
Is the register holding the shift length to apply to the value in Rm. Only the least significant byte
is used and can be in the range 0 to 255.
n
Is the shift length. The range of shift length depends on the instruction:
ASR
Shift length from 1 to 32.
LSL
Shift length from 0 to 31.
60
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
LSR
Shift length from 1 to 32.
ROR
Shift length from 1 to 31.
Note:
MOV{S}{cond} Rd, Rm is the preferred syntax for LSL{S}{cond} Rd, Rm, #0.
November 04, 2011
61
Texas Instruments Incorporated
General Data Processing Instructions
3.3.2
Operation
ASR, LSL, LSR, and ROR move the bits in the register Rm to the left or right by the number of places
specified by constant n or register Rs.
RRX moves the bits in register Rm to the right by 1.
In all these instructions, the result is written to Rd, but the value in register Rm remains unchanged.
For details on what result is generated by the different instructions, see “Shift Operations” on page 28.
3.3.3
Restrictions
Do not use SP and do not use PC.
3.3.4
Condition Flags
If S is specified:
■ These instructions update the N and Z flags according to the result.
■ The C flag is updated to the last bit shifted out, except when the shift length is 0. See “Shift
Operations” on page 28.
3.3.5
Examples
ASR
LSLS
LSR
ROR
RRX
R7,
R1,
R4,
R4,
R4,
R8,
R2,
R5,
R5,
R5
#9
#3
#6
R6
;
;
;
;
;
Arithmetic shift right by 9 bits.
Logical shift left by 3 bits with flag update.
Logical shift right by 6 bits.
Rotate right by the value in the bottom byte of R6.
Rotate right with extend.
62
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3.4
CLZ
Count Leading Zeros.
Applies to...
3.4.1
M3
M4
M4F
✓
✓
✓
Syntax
CLZ{cond} Rd, Rm
where:
cond
Is an optional condition code. See Table 1-2 on page 33.
Rd
Is the destination register.
Rm
Is the operand register.
3.4.2
Operation
The CLZ instruction counts the number of leading zeros in the value in Rm and returns the result in
Rd. The result value is 32 if no bits are set in the source register, and zero if bit[31] is set.
3.4.3
Restrictions
Do not use SP and do not use PC.
3.4.4
Condition Flags
This instruction does not change the flags.
3.4.5
Examples
CLZ
CLZNE
R4,R9
R2,R3
November 04, 2011
63
Texas Instruments Incorporated
General Data Processing Instructions
3.5
CMP and CMN
Compare and Compare Negative.
Applies to...
3.5.1
M3
M4
M4F
✓
✓
✓
Syntax
CMP{cond} Rn, Operand2
CMN{cond} Rn, Operand2
where:
cond
Is an optional condition code. See Table 1-2 on page 33.
Rn
Is the register holding the first operand.
Operand2
Is a flexible second operand. See “Flexible Second Operand” on page 27 for details of the
options.
3.5.2
Operation
These instructions compare the value in a register with Operand2. They update the condition flags
on the result, but do not write the result to a register.
The CMP instruction subtracts the value of Operand2 from the value in Rn. This is the same as a
SUBS instruction, except that the result is discarded.
The CMN instruction adds the value of Operand2 to the value in Rn. This is the same as an ADDS
instruction, except that the result is discarded.
3.5.3
Restrictions
In these instructions:
■ Do not use PC.
■ Operand2 must not be SP.
3.5.4
Condition Flags
These instructions update the N, Z, C and V flags according to the result.
3.5.5
Examples
CMP
CMN
CMPGT
R2, R9
R0, #6400
SP, R7, LSL #2
64
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3.6
MOV and MVN
Move and Move NOT.
Applies to...
3.6.1
M3
M4
M4F
✓
✓
✓
Syntax
MOV{S}{cond} Rd, Operand2
MOV{cond} Rd, #imm16
MVN{S}{cond} Rd, Operand2
where:
S
Is an optional suffix. If S is specified, the condition code flags are updated on the result of the
operation. See 32.
cond
Is an optional condition code. See Table 1-2 on page 33.
Rd
Is the destination register.
Operand2
Is a flexible second operand. See “Flexible Second Operand” on page 27 for details of the
options.
imm16
Is any value in the range 0-65535.
3.6.2
Operation
The MOV instruction copies the value of Operand2 into Rd.
When Operand2 in a MOV instruction is a register with a shift other than LSL #0, the preferred syntax
is the corresponding shift instruction:
MOV Instruction
Preferred Syntax using Shift Instruction
MOV{S}{cond} Rd, Rm, ASR #n
ASR{S}{cond} Rd, Rm, #n
MOV{S}{cond} Rd, Rm, LSL #n (if n != 0)
LSL{S}{cond} Rd, Rm, #n
MOV{S}{cond} Rd, Rm, LSR #n
LSR{S}{cond} Rd, Rm, #n
MOV{S}{cond} Rd, Rm, ROR #n
ROR{S}{cond} Rd, Rm, #n
MOV{S}{cond} Rd, Rm, RRX
RRX{S}{cond} Rd, Rm
Also, the MOV instruction permits additional forms of Operand2 as synonyms for shift instructions.
See “ASR, LSL, LSR, ROR, and RRX” on page 60.
Shift Instruction
MOV Instruction Synonym
ASR{S}{cond} Rd, Rm, Rs
MOV{S}{cond} Rd, Rm, ASR Rs
November 04, 2011
65
Texas Instruments Incorporated
General Data Processing Instructions
Shift Instruction
MOV Instruction Synonym
LSL{S}{cond} Rd, Rm, Rs
MOV{S}{cond} Rd, Rm, LSL Rs
LSR{S}{cond} Rd, Rm, Rs
MOV{S}{cond} Rd, Rm, LSR Rs
ROR{S}{cond} Rd, Rm, Rs
MOV{S}{cond} Rd, Rm, ROR Rs
The MVN instruction takes the value of Operand2, performs a bitwise logical NOT operation on the
value, and places the result into Rd.
Note:
3.6.3
The MOVW instruction provides the same function as MOV, but is restricted to using the imm16
operand.
Restrictions
You can use SP and PC only in the MOV instruction, with the following restrictions:
■ The second operand must be a register without shift
■ You must not specify the S suffix.
When Rd is PC in a MOV instruction:
■ Bit[0] of the value written to the PC is ignored
■ A branch occurs to the address created by forcing bit[0] of that value to 0.
Note:
3.6.4
Though it is possible to use MOV as a branch instruction, Texas Instruments strongly
recommends the use of a BX or BLX instruction to branch for software portability to the ARM
Cortex-M3/M4F instruction set.
Condition Flags
If S is specified, these instructions:
■ Update the N and Z flags according to the result.
■ Can update the C flag during the calculation of Operand2. See “Flexible Second
Operand” on page 27.
■ Do not affect the V flag.
3.6.5
Example
MOVS
MOV
MOVS
MOV
MOV
MVNS
R11, #0x000B
R1, #0xFA05
R10, R12
R3, #23
R8, SP
R2, #0xF
;
;
;
;
;
;
;
Write
Write
Write
Write
Write
Write
to R2
value of 0x000B to R11, flags get updated.
value of 0xFA05 to R1, flags are not updated.
value in R12 to R10, flags get updated.
value of 23 to R3.
value of stack pointer to R8.
value of 0xFFFFFFF0 (bitwise inverse of 0xF)
and update flags.
66
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3.7
MOVT
Move Top.
Applies to...
3.7.1
M3
M4
M4F
✓
✓
Syntax
MOVT{cond} Rd, #imm16
where:
cond
Is an optional condition code. See Table 1-2 on page 33.
Rd
Is the destination register.
imm16
Is a 16-bit immediate constant.
3.7.2
Operation
MOVT writes a 16-bit immediate value, imm16, to the top halfword, Rd[31:16], of its destination
register. The write does not affect Rd[15:0].
The MOV, MOVT instruction pair enables you to generate any 32-bit constant.
3.7.3
Restrictions
Rd must not be SP and must not be PC.
3.7.4
Condition Flags
This instruction does not change the flags.
3.7.5
Examples
MOVT
R3, #0xF123 ; Write 0xF123 to upper halfword of R3, lower halfword
; and APSR are unchanged.
November 04, 2011
67
Texas Instruments Incorporated
General Data Processing Instructions
3.8
REV, REV16, REVSH, and RBIT
Reverse bytes and Reverse bits.
Applies to...
3.8.1
M3
M4
M4F
✓
✓
✓
Syntax
op{cond} Rd, Rn
where:
op
Is any of:
REV
Reverse byte order in a word.
REV16
Reverse byte order in each halfword independently.
REVSH
Reverse byte order in the bottom halfword, and sign extend to 32 bits.
RBIT
Reverse the bit order in a 32-bit word.
cond
Is an optional condition code. See Table 1-2 on page 33.
Rd
Is the destination register.
Rn
Is the register holding the operand.
3.8.2
Operation
Use these instructions to change endianness of data:
REV
Converts 32-bit big-endian data into little-endian data or 32-bit little-endian data into big-endian
data.
REV16
Converts 16-bit big-endian data into little-endian data or 16-bit little-endian data into big-endian
data.
REVSH
Converts either:
■ 16-bit signed big-endian data into 32-bit signed little-endian data.
■ 16-bit signed little-endian data into 32-bit signed big-endian data.
68
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3.8.3
Restrictions
Do not use SP and do not use PC.
3.8.4
Condition Flags
These instructions do not change the flags.
3.8.5
Examples
REV
REV16
REVSH
REVHS
RBIT
R3,
R0,
R0,
R3,
R7,
R7
R0
R5
R7
R8
;
;
;
;
;
Reverse
Reverse
Reverse
Reverse
Reverse
byte order of value in R7 and write it to R3.
byte order of each 16-bit halfword in R0.
Signed Halfword.
with Higher or Same condition.
bit order of value in R8 and write the result to R7.
November 04, 2011
69
Texas Instruments Incorporated
General Data Processing Instructions
3.9
SADD16 and SADD8
Signed Add 16 and Signed Add 8.
Applies to...
3.9.1
M3
M4
M4F
✓
✓
Syntax
op{cond}{Rd,} Rn, Rm
where:
op
is any of:
SADD16
Performs two 16-bit signed integer additions.
SADD8
Performs four 8-bit signed integer additions.
cond
is an optional condition code, see 33.
Rd
is the destination register.
Rn
is the first register holding the operand.
Rm
is the second register holding the operand.
3.9.2
Operation
Use these instructions to perform a halfword or byte add in parallel:
The SADD16 instruction:
1. Adds each halfword from the first operand to the corresponding halfword of the second
operand.
2. Writes the result in the corresponding halfwords of the destination register.
The SADD8 instruction:
1. Adds each byte of the first operand to the corresponding byte of the second operand.
2. Writes the result in the corresponding bytes of the destination register.
3.9.3
Restrictions
Do not use SP and do not use PC.
70
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3.9.4
Condition flags
These instructions do not change the flags.
3.9.5
Examples
SADD16 R1, R0
; Adds the halfwords in R0 to the corresponding halfwords of
; R1 and writes to corresponding halfword of R1.
SADD8
; Adds bytes of R0 to the corresponding byte in R5 and writes
R4, R0, R5
; to the corresponding byte in R4.
November 04, 2011
71
Texas Instruments Incorporated
General Data Processing Instructions
3.10
SHADD16 and SHADD8
Signed Halving Add 16 and Signed Halving Add 8.
Applies to...
3.10.1
M3
M4
M4F
✓
✓
Syntax
op{cond}{Rd,} Rn, Rm
where:
op
is any of:
SHADD16
Signed Halving Add 16
SHADD8
Signed Halving Add 8
cond
is an optional condition code, see 33.
Rd
is the destination register.
Rn
is the first operand register.
Rm
is the second operand register.
3.10.2
Operation
Use these instructions to add 16-bit and 8-bit data and then to halve the result before writing the
result to the destination register:
The SHADD16 instruction:
1. Adds each halfword from the first operand to the corresponding halfword of the second
operand.
2. Shuffles the result by one bit to the right, halving the data.
3. Writes the halfword results in the destination register.
The SHADDB8 instruction:
1. Adds each byte of the first operand to the corresponding byte of the second operand.
2. Shuffles the result by one bit to the right, halving the data.
72
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3. Writes the byte results in the destination register.
3.10.3
Restrictions
Do not use SP and do not use PC.
3.10.4
Condition flags
These instructions do not change the flags.
3.10.5
Examples
SHADD16 R1, R0
SHADD8
; Adds halfwords in R0 to corresponding halfword of R1 and
; writes halved result to corresponding halfword in R1
R4, R0, R5 ; Adds bytes of R0 to corresponding byte in R5 and
; writes halved result to corresponding byte in R4
November 04, 2011
73
Texas Instruments Incorporated
General Data Processing Instructions
3.11
SHASX and SHSAX
Signed Halving Add and Subtract with Exchange and Signed Halving Subtract and Add with
Exchange.
Applies to...
3.11.1
M3
M4
M4F
✓
✓
Syntax
op{cond} {Rd}, Rn, Rm
where:
op
is any of:
SHASX
Add and Subtract with Exchange and Halving.
SHSAX
Subtract and Add with Exchange and Halving.
cond
is an optional condition code, see 33.
Rd
is the destination register.
Rn, Rm
are registers holding the first and second operands.
3.11.2
Operation
The SHASX instruction:
1. Adds the top halfword of the first operand with the bottom halfword of the second operand.
2. Writes the halfword result of the addition to the top halfword of the destination register, shifted
by one bit to the right causing a divide by two, or halving.
3. Subtracts the top halfword of the second operand from the bottom highword of the first operand.
4. Writes the halfword result of the division in the bottom halfword of the destination register, shifted
by one bit to the right causing a divide by two, or halving.
The SHSAX instruction:
1. Subtracts the bottom halfword of the second operand from the top highword of the first operand.
2. Writes the halfword result of the addition to the bottom halfword of the destination register,
shifted by one bit to the right causing a divide by two, or halving.
3. Adds the bottom halfword of the first operand with the top halfword of the second operand.
74
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
4. Writes the halfword result of the division in the top halfword of the destination register, shifted
by one bit to the right causing a divide by two, or halving.
3.11.3
Restrictions
Do not use SP and do not use PC.
3.11.4
Condition flags
These instructions do not affect the condition code flags.
November 04, 2011
75
Texas Instruments Incorporated
General Data Processing Instructions
3.11.5
Examples
SHASX
R7, R4, R2
; Adds top halfword of R4 to bottom halfword of R2
; and writes halved result to top halfword of R7
; Subtracts top halfword of R2 from bottom halfword of
; R4 and writes halved result to bottom halfword of R7
SHSAX
R0, R3, R5
; Subtracts bottom halfword of R5 from top halfword
; of R3 and writes halved result to top halfword of R0
; Adds top halfword of R5 to bottom halfword of R3 and
; writes halved result to bottom halfword of R0
76
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3.12
SHSUB16 and SHSUB8
Signed Halving Subtract 16 and Signed Halving Subtract 8.
Applies to...
3.12.1
M3
M4
M4F
✓
✓
Syntax
op{cond}{Rd,} Rn, Rm
where:
op
is any of:
SHSUB16
Signed Halving Subtract 16
SHSUB8
Signed Halving Subtract 8
cond
is an optional condition code, see 33.
Rd
is the destination register.
Rn
is the first operand register.
Rm
is the second operand register
3.12.2
Operation
Use these instructions to add 16-bit and 8-bit data and then to halve the result before writing the
result to the destination register:
The SHSUB16 instruction:
1. Subtracts each halfword of the second operand from the corresponding halfwords of the
first operand.
2. Shuffles the result by one bit to the right, halving the data.
3. Writes the halved halfword results in the destination register.
The SHSUBB8 instruction:
1. Subtracts each byte of the second operand from the corresponding byte of the first operand,
2. Shuffles the result by one bit to the right, halving the data,
November 04, 2011
77
Texas Instruments Incorporated
General Data Processing Instructions
3. Writes the corresponding signed byte results in the destination register.
3.12.3
Restrictions
Do not use SP and do not use PC.
3.12.4
Condition flags
These instructions do not change the flags.
3.12.5
Examples
SHSUB16 R1, R0
; Subtracts halfwords in R0 from corresponding halfword
; of R1 and writes to corresponding halfword of R1
SHSUB8
; Subtracts bytes of R0 from corresponding byte in R5,
R4, R0, R5
; and writes to corresponding byte in R4
78
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3.13
SSUB16 and SSUB8
Signed Subtract 16 and Signed Subtract 8.
Applies to...
3.13.1
M3
M4
M4F
✓
✓
Syntax
op{cond}{Rd,} Rn, Rm
where:
op
is any of:
SSUB16
Performs two 16-bit signed integer subtractions.
SSUB8
Performs four 8-bit signed integer subtractions.
cond
is an optional condition code, see 33.
Rd
is the destination register.
Rn
is the first operand register.
Rm
is the second operand register.
3.13.2
Operation
Use these instructions to change endianness of data:
The SSUB16 instruction:
1. Subtracts each halfword from the second operand from the corresponding halfword of the
first operand
2. Writes the difference result of two signed halfwords in the corresponding halfword of the
destination register.
The SSUB8 instruction:
1. Subtracts each byte of the second operand from the corresponding byte of the first operand
2. Writes the difference result of four signed bytes in the corresponding byte of the destination
register.
November 04, 2011
79
Texas Instruments Incorporated
General Data Processing Instructions
3.13.3
Restrictions
Do not use SP and do not use PC.
3.13.4
Condition flags
These instructions do not change the flags.
3.13.5
Examples
SSUB16 R1, R0
; Subtracts halfwords in R0 from corresponding halfword of R1
; and writes to corresponding halfword of R1
SSUB8
; Subtracts bytes of R5 from corresponding byte in
; R0, and writes to corresponding byte of R4
R4, R0, R5
80
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3.14
SASX and SSAX
Signed Add and Subtract with Exchange and Signed Subtract and Add with Exchange.
Applies to...
3.14.1
M3
M4
M4F
✓
✓
Syntax
op{cond} {Rd}, Rm, Rn
op{cond} {Rd}, Rm, Rn
where:
op
is any of:
SASX
Signed Add and Subtract with Exchange.
SSAX
Signed Subtract and Add with Exchange.
cond
is an optional condition code, see 33.
Rd
is the destination register.
Rn, Rm
are registers holding the first and second operands.
3.14.2
Operation
The SASX instruction:
1. Adds the signed top halfword of the first operand with the signed bottom halfword of the second
operand.
2. Writes the signed result of the addition to the top halfword of the destination register.
3. Subtracts the signed bottom halfword of the second operand from the top signed highword of
the first operand.
4. Writes the signed result of the subtraction to the bottom halfword of the destination register.
The SSAX instruction:
1. Subtracts the signed bottom halfword of the second operand from the top signed highword of
the first operand.
2. Writes the signed result of the addition to the bottom halfword of the destination register.
November 04, 2011
81
Texas Instruments Incorporated
General Data Processing Instructions
3. Adds the signed top halfword of the first operand with the signed bottom halfword of the second
operand.
4. Writes the signed result of the subtraction to the top halfword of the destination register.
3.14.3
Restrictions
Do not use SP and do not use PC.
3.14.4
Condition flags
These instructions do not affect the condition code flags.
82
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3.14.5
Examples
SASX
R0, R4, R5
; Adds top halfword of R4 to bottom halfword of R5 and
; writes to top halfword of R0
; Subtracts bottom halfword of R5 from top halfword of R4
; and writes to bottom halfword of R0
SSAX
R7, R3, R2
; Subtracts top halfword of R2 from bottom halfword of R3
; and writes to bottom halfword of R7
; Adds top halfword of R3 with bottom halfword of R2 and
; writes to top halfword of R7
November 04, 2011
83
Texas Instruments Incorporated
General Data Processing Instructions
3.15
TST and TEQ
Test bits and Test Equivalence.
Applies to...
3.15.1
M3
M4
M4F
✓
✓
✓
Syntax
TST{cond} Rn, Operand2
TEQ{cond} Rn, Operand2
where:
cond
Is an optional condition code. See Table 1-2 on page 33.
Rn
Is the register holding the first operand.
Operand2
Is a flexible second operand. See “Flexible Second Operand” on page 27 for details of the
options.
3.15.2
Operation
These instructions test the value in a register against Operand2. They update the condition flags
based on the result, but do not write the result to a register.
The TST instruction performs a bitwise AND operation on the value in Rn and the value of Operand2.
This is the same as the ANDS instruction, except that it discards the result.
To test whether a bit of Rn is 0 or 1, use the TST instruction with an Operand2 constant that has
that bit set to 1 and all other bits cleared to 0.
The TEQ instruction performs a bitwise Exclusive OR operation on the value in Rn and the value of
Operand2. This is the same as the EORS instruction, except that it discards the result.
Use the TEQ instruction to test if two values are equal without affecting the V or C flags.
TEQ is also useful for testing the sign of a value. After the comparison, the N flag is the logical
Exclusive OR of the sign bits of the two operands.
3.15.3
Restrictions
Do not use SP and do not use PC.
84
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3.15.4
Condition Flags
These instructions:
■ Update the N and Z flags according to the result.
■ Can update the C flag during the calculation of Operand2. See “Flexible Second
Operand” on page 27.
■ Do not affect the V flag.
3.15.5
Examples
TST
R0, #0x3F8
TEQEQ
R10, R9
;
;
;
;
Perform bitwise AND of R0 value to 0x3F8;
APSR is updated but result is discarded.
Conditionally test if value in R10 is equal to
value in R9; APSR is updated but result is discarded.
November 04, 2011
85
Texas Instruments Incorporated
General Data Processing Instructions
3.16
UADD16 and UADD8
Unsigned Add 16 and Unsigned Add 8.
Applies to...
3.16.1
M3
M4
M4F
✓
✓
Syntax
op{cond}{Rd,} Rn, Rm
where:
op
is any of:
UADD16
Performs two 16-bit unsigned integer additions.
UADD8
Performs four 8-bit unsigned integer additions.
cond
is an optional condition code, see 33.
Rd
is the destination register.
Rn
is the first register holding the operand.
Rm
is the second register holding the operand.
3.16.2
Operation
Use these instructions to add 16- and 8-bit unsigned data:
The UADD16 instruction:
1. adds each halfword from the first operand to the corresponding halfword of the second operand.
2. writes the unsigned result in the corresponding halfwords of the destination register.
The UADD16 instruction:
1. adds each byte of the first operand to the corresponding byte of the second operand.
2. writes the unsigned result in the corresponding byte of the destination register.
3.16.3
Restrictions
Do not use SP and do not use PC.
86
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3.16.4
Condition flags
These instructions do not change the flags.
3.16.5
Examples
UADD16 R1, R0
; Adds halfwords in R0 to corresponding halfword of R1,
; writes to corresponding halfword of R1
UADD8
; Adds bytes of R0 to corresponding byte in R5 and writes
; to corresponding byte in R4
R4, R0, R5
November 04, 2011
87
Texas Instruments Incorporated
General Data Processing Instructions
3.17
UASX and USAX
Add and Subtract with Exchange and Subtract and Add with Exchange.
Applies to...
3.17.1
M3
M4
M4F
✓
✓
Syntax
op{cond} {Rd}, Rn, Rm
where:
op
is one of:
UASX
Add and Subtract with Exchange.
USAX
Subtract and Add with Exchange.
cond
is an optional condition code, see 33.
Rd
is the destination register.
Rn, Rm
are registers holding the first and second operands.
3.17.2
Operation
The UASX instruction:
1. Subtracts the top halfword of the second operand from the bottom halfword of the first operand.
2. Writes the unsigned result from the subtraction to the bottom halfword of the destination register.
3. Adds the top halfword of the first operand with the bottom halfword of the second operand.
4. Writes the unsigned result of the addition to the top halfword of the destination register.
The USAX instruction:
1. Adds the bottom halfword of the first operand with the top halfword of the second operand.
2. Writes the unsigned result of the addition to the bottom halfword of the destination register.
3. Subtracts the bottom halfword of the second operand from the top halfword of the first operand.
4. Writes the unsigned result from the subtraction to the top halfword of the destination register.
88
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3.17.3
Restrictions
Do not use SP and do not use PC.
3.17.4
Condition flags
These instructions do not affect the condition code flags.
November 04, 2011
89
Texas Instruments Incorporated
General Data Processing Instructions
3.17.5
Examples
UASX
R0, R4, R5
; Adds top halfword of R4 to bottom halfword of R5 and
; writes to top halfword of R0
; Subtracts bottom halfword of R5 from top halfword of R0
; and writes to bottom halfword of R0
USAX
R7, R3, R2
; Subtracts top halfword of R2 from bottom halfword of R3
; and writes to bottom halfword of R7
; Adds top halfword of R3 to bottom halfword of R2 and
; writes to top halfword of R7
90
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3.18
UHADD16 and UHADD8
Unsigned Halving Add 16 and Unsigned Halving Add 8.
Applies to...
3.18.1
M3
M4
M4F
✓
✓
Syntax
op{cond}{Rd,} Rn, Rm
where:
op
is any of:
UHADD16
Unsigned Halving Add 16.
UHADD8
Unsigned Halving Add 8.
cond
is an optional condition code, see 33.
Rd
is the destination register.
Rn
is the register holding the first operand.
Rm
is the register holding the second operand.
3.18.2
Operation
Use these instructions to add 16- and 8-bit data and then to halve the result before writing the result
to the destination register:
The UHADD16 instruction:
1. Adds each halfword from the first operand to the corresponding halfword of the second operand.
2. Shuffles the halfword result by one bit to the right, halving the data.
3. Writes the unsigned results to the corresponding halfword in the destination register.
The UHADD8 instruction:
1. Adds each byte of the first operand to the corresponding byte of the second operand.
2. Shuffles the byte result by one bit to the right, halving the data.
3. Writes the unsigned results in the corresponding byte in the destination register.
November 04, 2011
91
Texas Instruments Incorporated
General Data Processing Instructions
3.18.3
Restrictions
Do not use SP and do not use PC.
3.18.4
Condition flags
These instructions do not change the flags.
3.18.5
Examples
UHADD16 R7, R3
; Adds halfwords in R7 to corresponding halfword of R3
; and writes halved result to corresponding halfword in R7
UHADD8
; Adds bytes of R0 to corresponding byte in R5 and writes
R4, R0, R5
; halved result to corresponding byte in R4
92
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3.19
UHASX and UHSAX
Unsigned Halving Add and Subtract with Exchange and Unsigned Halving Subtract and Add with
Exchange.
Applies to...
3.19.1
M3
M4
M4F
✓
✓
Syntax
op{cond} {Rd}, Rn, Rm
where:
op
is one of:
UHASX
Add and Subtract with Exchange and Halving.
UHSAX
Subtract and Add with Exchange and Halving.
cond
is an optional condition code, see 33.
Rd
is the destination register.
Rn, Rm
are registers holding the first and second operands.
3.19.2
Operation
The UHASX instruction:
1. Adds the top halfword of the first operand with the bottom halfword of the second operand.
2. Shifts the result by one bit to the right causing a divide by two, or halving.
3. Writes the halfword result of the addition to the top halfword of the destination register.
4. Subtracts the top halfword of the second operand from the bottom highword of the first operand.
5. Shifts the result by one bit to the right causing a divide by two, or halving.
6. Writes the halfword result of the division in the bottom halfword of the destination register.
The UHSAX instruction:
1. Subtracts the bottom halfword of the second operand from the top highword of the first operand.
2. Shifts the result by one bit to the right causing a divide by two, or halving.
3. Writes the halfword result of the subtraction in the top halfword of the destination register.
November 04, 2011
93
Texas Instruments Incorporated
General Data Processing Instructions
4. Adds the bottom halfword of the first operand with the top halfword of the second operand.
5. Shifts the result by one bit to the right causing a divide by two, or halving.
6. Writes the halfword result of the addition to the bottom halfword of the destination register.
3.19.3
Restrictions
Do not use SP and do not use PC.
3.19.4
Condition flags
These instructions do not affect the condition code flags.
94
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3.19.5
Examples
UHASX
R7, R4, R2
; Adds top halfword of R4 with bottom halfword of R2
; and writes halved result to top halfword of R7
; Subtracts top halfword of R2 from bottom halfword of
; R7 and writes halved result to bottom halfword of R7
UHSAX
R0, R3, R5
; Subtracts bottom halfword of R5 from top halfword of
; R3 and writes halved result to top halfword of R0
; Adds top halfword of R5 to bottom halfword of R3 and
; writes halved result to bottom halfword of R0
November 04, 2011
95
Texas Instruments Incorporated
General Data Processing Instructions
3.20
UHSUB16 and UHSUB8
Unsigned Halving Subtract 16 and Unsigned Halving Subtract 8.
Applies to...
3.20.1
M3
M4
M4F
✓
✓
Syntax
op{cond}{Rd,} Rn, Rm
where:
op
is any of:
UHSUB16
Performs two unsigned 16-bit integer additions, halves the results, and writes the results
to the destination register.
UHSUB8
Performs four unsigned 8-bit integer additions, halves the results, and writes the results to
the destination register.
cond
is an optional condition code, see 33.
Rd
is the destination register.
Rn
is the first register holding the operand.
Rm
is the second register holding the operand.
3.20.2
Operation
Use these instructions to add 16-bit and 8-bit data and then to halve the result before writing the
result to the destination register:
The UHSUB16 instruction:
1. Subtracts each halfword of the second operand from the corresponding halfword of the first
operand.
2. Shuffles each halfword result to the right by one bit, halving the data.
3. Writes each unsigned halfword result to the corresponding halfwords in the destination register.
The UHSUB8 instruction:
1. Subtracts each byte of second operand from the corresponding byte of the first operand.
2. Shuffles each byte result by one bit to the right, halving the data.
96
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3. Writes the unsigned byte results to the corresponding byte of the destination register.
3.20.3
Restrictions
Do not use SP and do not use PC.
3.20.4
Condition flags
These instructions do not change the flags.
3.20.5
Examples
UHSUB16
R1, R0
; Subtracts halfwords in R0 from corresponding halfword of
; R1 and writes halved result to corresponding halfword in
; R1
UHSUB8
R4, R0, R5
; Subtracts bytes of R5 from corresponding byte in R0 and
; writes halved result to corresponding byte in R4
November 04, 2011
97
Texas Instruments Incorporated
General Data Processing Instructions
3.21
SEL
Select Bytes. Selects each byte of its result from either its first operand or its second operand,
according to the values of the GE flags.
Applies to...
3.21.1
M3
M4
M4F
✓
✓
Syntax
SEL{<c>}{<q>} {<Rd>,} <Rn>, <Rm>
where:
<c>, <q>
is a standard assembler syntax fields.
<Rd>
is the destination register.
<Rn>
is the first operand register.
<Rm>
is the second operand register.
3.21.2
Operation
The SEL instruction:
1. Reads the value of each bit of APSR.GE.
2. Depending on the value of APSR.GE, assigns the destination register the value of either the
first or second operand register.
3.21.3
Restrictions
None.
3.21.4
Condition flags
These instructions do not change the flags.
3.21.5
Examples
SADD16 R0, R1, R2
; Set GE bits based on result
SEL R0, R0, R3
; Select bytes from R0 or R3, based on GE
98
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3.22
USAD8
Unsigned Sum of Absolute Differences.
Applies to...
3.22.1
M3
M4
M4F
✓
✓
Syntax
USAD8{cond}{Rd,} Rn, Rm
where:
cond
is an optional condition code, see 33.
Rd
is the destination register.
Rn
is the first operand register.
Rm
is the second operand register.
3.22.2
Operation
The USAD8 instruction:
1. Subtracts each byte of the second operand register from the corresponding byte of the first
operand register.
2. Adds the absolute values of the differences together.
3. Writes the result to the destination register.
3.22.3
Restrictions
Do not use SP and do not use PC.
3.22.4
Condition flags
These instructions do not change the flags.
3.22.5
Examples
USAD8 R1, R4, R0
; Subtracts each byte in R0 from corresponding byte of R4
; adds the differences and writes to R1
USAD8
; Subtracts bytes of R5 from corresponding byte in R0,
R0, R5
; adds the differences and writes to R0
November 04, 2011
99
Texas Instruments Incorporated
General Data Processing Instructions
100
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3.23
USADA8
Unsigned Sum of Absolute Differences and Accumulate.
Applies to...
3.23.1
M3
M4
M4F
✓
✓
Syntax
USADA8{cond}{Rd,} Rn, Rm, Ra
where:
cond
is an optional condition code, see 33.
Rd
is the destination register.
Rn
is the first operand register.
Rm
is the second operand register.
Ra
is the register that contains the accumulation value.
3.23.2
Operation
The USADA8 instruction:
1. Subtracts each byte of the second operand register from the corresponding byte of the first
operand register.
2. Adds the unsigned absolute differences together.
3. Adds the accumulation value to the sum of the absolute differences.
4. Writes the result to the destination register.
3.23.3
Restrictions
Do not use SP and do not use PC.
3.23.4
Condition flags
These instructions do not change the flags.
3.23.5
Examples
USADA8 R1, R0, R6
; Subtracts bytes in R0 from corresponding halfword of R1
; adds differences, adds value of R6, writes to R1
November 04, 2011
101
Texas Instruments Incorporated
General Data Processing Instructions
USADA8
R4, R0, R5, R2 ; Subtracts bytes of R5 from corresponding byte in R0
; adds differences, adds value of R2 writes to R4
102
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
3.24
USUB16 and USUB8
Unsigned Subtract 16 and Unsigned Subtract 8.
Applies to...
3.24.1
M3
M4
M4F
✓
✓
Syntax
op{cond}{Rd,} Rn, Rm
where:
op
is any of:
USUB16
Unsigned Subtract 16.
USUB8
Unsigned Subtract 8.
cond
is an optional condition code, see 33.
Rd
is the destination register.
Rn
is the first operand register.
Rm
is the second operand register.
3.24.2
Operation
Use these instructions to subtract 16-bit and 8-bit data before writing the result to the destination
register:
The USUB16 instruction:
1. Subtracts each halfword from the second operand register from the corresponding halfword of
the first operand register.
2. Writes the unsigned result in the corresponding halfwords of the destination register.
The USUB8 instruction:
1. Subtracts each byte of the second operand register from the corresponding byte of the first
operand register.
2. Writes the unsigned byte result in the corresponding byte of the destination register.
November 04, 2011
103
Texas Instruments Incorporated
General Data Processing Instructions
3.24.3
Restrictions
Do not use SP and do not use PC.
3.24.4
Condition flags
These instructions do not change the flags.
3.24.5
Examples
USUB16 R1, R0
; Subtracts halfwords in R0 from corresponding halfword of R1
; and writes to corresponding halfword in R1USUB8 R4, R0, R5
; writes to the corresponding byte in R4
104
November 04, 2011
Texas Instruments Incorporated
;
Cortex-M3/M4F Instruction Set
4
Multiply and Divide Instructions
Table 4-1 on page 105 shows the multiply and divide instructions:
Table 4-1. Multiply and Divide Instructions
Mnemonic
Brief Description
MLA
Multiply with accumulate, 32-bit result
106
MLS
Multiply and subtract, 32-bit result
106
MUL
Multiply, 32-bit result
106
SDIV
Signed divide
130
SMLA[B,T]
Signed multiply accumulate (halfwords)
108
SMLAD, SMLADX
Signed multiply accumulate dual
111
SMLAL
Signed multiply with accumulate (32x32+64), 64-bit result
128
SMLAL[B,T]
Signed multiply accumulate long (halfwords)
113
SMLALD, SMLALDX
Signed multiply accumulate long dual
113
SMLAW[B|T]
Signed multiply accumulate (word by halfword)
108
SMLSD
Signed multiply subtract dual
116
SMLSLD
Signed multiply subtract long dual
116
SMMLA
Signed most significant word multiply accumulate
119
SMMLS, SMMLSR
Signed most significant word multiply subtract
119
SMUAD, SMUADX
Signed dual multiply add
123
SMUL[B,T]
Signed multiply (word by halfword)
125
SMMUL, SMMULR
Signed most significant word multiply
121
SMULL
Signed multiply (32x32), 64-bit result
128
SMULWB, SMULWT
Signed multiply (word by halfword)
125
SMUSD, SMUSDX
Signed dual multiply subtract
123
UDIV
Unsigned divide
130
UMAAL
Unsigned multiply accumulate accumulate long
(32x32+32+32), 64-bit result
128
UMLAL
Unsigned multiply with accumulate (32x32+64), 64-bit result
128
UMULL
Unsigned multiply (32x32), 64-bit result
128
November 04, 2011
See Page
105
Texas Instruments Incorporated
Multiply and Divide Instructions
4.1
MUL, MLA, and MLS
Multiply, Multiply with Accumulate, and Multiply with Subtract, using 32-bit operands, and producing
a 32-bit result.
Applies to...
4.1.1
M3
M4
M4F
✓
✓
✓
Syntax
MUL{S}{cond} {Rd,} Rn, Rm ; Multiply
MLA{cond} Rd, Rn, Rm, Ra
; Multiply with accumulate
MLS{cond} Rd, Rn, Rm, Ra
; Multiply with subtract
where:
cond
Is an optional condition code. See Table 1-2 on page 33.
S
Is an optional suffix. If S is specified, the condition code flags are updated on the result of the
operation. See 33.
Rd
Is the destination register. If Rd is omitted, the destination register is Rn.
Rn, Rm
Are registers holding the values to be multiplied.
Ra
Is a register holding the value to be added or subtracted from.
4.1.2
Operation
The MUL instruction multiplies the values from Rn and Rm, and places the least-significant 32 bits
of the result in Rd.
The MLA instruction multiplies the values from Rn and Rm, adds the value from Ra, and places the
least-significant 32 bits of the result in Rd.
The MLS instruction multiplies the values from Rn and Rm, subtracts the product from Ra, and places
the least-significant 32 bits of the result in Rd.
The results of these instructions do not depend on whether the operands are signed or unsigned.
4.1.3
Restrictions
In these instructions, do not use SP and do not use PC.
If you use the S suffix with the MUL instruction:
■ Rd, Rn, and Rm must all be in the range R0 to R7.
■ Rd must be the same as Rm.
106
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
■ You must not use the cond suffix.
4.1.4
Condition Flags
If S is specified, the MUL instruction:
■ Updates the N and Z flags according to the result.
■ Does not affect the C and V flags.
4.1.5
Examples
MUL
MLA
MULS
MULLT
MLS
R10, R2, R5
R10, R2, R1, R5
R0, R2, R2
R2, R3, R2
R4, R5, R6, R7
;
;
;
;
;
Multiply, R10
Multiply with
Multiply with
Conditionally
Multiply with
= R2 x R5.
accumulate, R10 =
flag update, R0 =
multiply, R2 = R3
subtract, R4 = R7
November 04, 2011
(R2 x R1) + R5.
R2 x R2.
x R2.
- (R5 x R6).
107
Texas Instruments Incorporated
Multiply and Divide Instructions
4.2
SMLA and SMLAW
Signed Multiply Accumulate (halfwords).
Applies to...
4.2.1
M3
M4
M4F
✓
✓
Syntax
op{X}{Y}{cond} Rd, Rn, Rm
op{Y}{cond} Rd, Rn, Rm, Ra
where
op
is one of:
SMLAXY
Signed Multiply Accumulate Long (halfwords)
X and Y specifies which half of the source registers Rn and Rm are used as the first and second
multiply operand.
If X is B, then the bottom halfword, bits [15:0], of Rn is used. If X is T, then the top halfword, bits
[31:16], of Rn is used.
If Y is B, then the bottom halfword, bits [15:0], of Rm is used. If Y is T, then the top halfword, bits
[31:16], of Rm is used.
SMLAWY
Signed Multiply Accumulate (word by halfword)
Y specifies which half of the source register Rm is used as the second multiply operand.
If Y is T, then the top halfword, bits [31:16] of Rm is used.
If Y is B, then the bottom halfword, bits [15:0] of Rm is used.
cond
is an optional condition code, see Table 1-2 on page 33.
Rd
is the destination register. If Rd is omitted, the destination register is Rn.
Rn, Rm
are registers holding the values to be multiplied.
Ra
is a register holding the value to be added or subtracted from.
4.2.2
Operation
The SMALBB, SMLABT, SMLATB, SMLATT instructions:
108
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
■ Multiplies the specified signed halfword, top or bottom, values from Rn and Rm.
■ Adds the value in Ra to the resulting 32-bit product.
■ Writes the result of the multiplication and addition in Rd.
The non-specified halfwords of the source registers are ignored.
The SMLAWB and SMLAWT instructions:
■ Multiply the 32-bit signed values in Rn with:
– The top signed halfword of Rm, T instruction suffix.
– The bottom signed halfword of Rm, B instruction suffix.
■ Add the 32-bit signed value in Ra to the top 32 bits of the 48-bit product
■ Writes the result of the multiplication and addition in Rd.
The bottom 16 bits of the 48-bit product are ignored.
If overflow occurs during the addition of the accumulate value, the instruction sets the Q flag in the
APSR. No overflow can occur during the multiplication.
4.2.3
Restrictions
In these instructions, do not use SP and do not use PC.
4.2.4
Condition flags
If an overflow is detected, the Q flag is set.
4.2.5
Examples
SMLABB
R5, R6, R4, R1
; Multiplies bottom halfwords of R6 and R4, adds
; R1 and writes to R5
SMLATB
R5, R6, R4, R1
; Multiplies top halfword of R6 with bottom halfword
; of R4, adds R1 and writes to R5
SMLATT
R5, R6, R4, R1
; Multiplies top halfwords of R6 and R4, adds
; R1 and writes the sum to R5
SMLABT
R5, R6, R4, R1
; Multiplies bottom halfword of R6 with top halfword
; of R4, adds R1 and writes to R5
November 04, 2011
109
Texas Instruments Incorporated
Multiply and Divide Instructions
SMLABT
R4, R3, R2
; Multiplies bottom halfword of R4 with top halfword of
; R3, adds R2 and writes to R4
SMLAWB
R10, R2, R5, R3 ; Multiplies R2 with bottom halfword of R5, adds
; R3 to the result and writes top 32-bits to R10
SMLAWT
R10, R2, R1, R5 ; Multiplies R2 with top halfword of R1, adds R5
; and writes top 32-bits to R10
110
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
4.3
SMLAD
Signed Multiply Accumulate Long Dual.
Applies to...
4.3.1
M3
M4
M4F
✓
✓
Syntax
SMLAD{X}{cond} Rd, Rn, Rm, Ra
;
where:
SMLAD
Signed Multiply Accumulate Dual
SMLADX
Signed Multiply Accumulate Dual Reverse
X
Specifies which halfword of the source register Rn is used as the multiply operand. If X is omitted,
the multiplications are bottom × bottom and top × top. If X is present, the multiplications are
bottom × top and top × bottom.
cond
is an optional condition code, see Table 1-2 on page 33.
Rd
is the destination register.
Rn
is the first operand register holding the values to be multiplied.
Rm
the second operand register.
Ra
is the accumulate value.
4.3.2
Operation
The SMLAD and SMLADX instructions regard the two operands as four halfword 16-bit values. The
SMLAD and SMLADX instructions:
■ If X is not present, multiply the top signed halfword value in Rn with the top signed halfword of
Rm and the bottom signed halfword values in Rn with the bottom signed halfword of Rm.
■ Or if X is present, multiply the top signed halfword value in Rn with the bottom signed halfword
of Rm and the bottom signed halfword values in Rn with the top signed halfword of Rm.
■ Add both multiplication results to the signed 32-bit value in Ra.
■ Writes the 32-bit signed result of the multiplication and addition to Rd.
4.3.3
Restrictions
Do not use SP and do not use PC.
November 04, 2011
111
Texas Instruments Incorporated
Multiply and Divide Instructions
4.3.4
Condition flags
These instructions do not change the flags.
4.3.5
Examples
SMLAD
R10, R2, R1, R5 ; Multiplies two halfword values in R2 with
; corresponding halfwords in R1, adds R5 and writes to
; R10
SMLALDX R0, R2, R4, R6
; Multiplies top halfword of R2 with bottom halfword
; of R4, multiplies bottom halfword of R2 with top
; halfword of R4, adds R6 and writes to R0
112
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
4.4
SMLAL and SMLALD
Signed Multiply Accumulate Long and Signed Multiply Accumulate Long Dual and Signed Multiply
Accumulate Long (halfwords).
SMLAL
Applies to...
4.4.1
SMLALD
M3
M4
M4F
✓
✓
✓
M3
M4
M4F
✓
✓
Syntax
SMLAL{cond} RdLo, RdHi, Rn, Rm
SMLAL{X}{Y}{cond} RdLo, RdHi, Rn, Rm
SMLALD{X}{cond} RdLo, RdHi, Rn, Rm
where:
SMLAL
Signed Multiply Accumulate Long
SMLAL{X}{Y}
Signed Multiply Accumulate Long (halfwords, X and Y)
{X}{Y}
Specifies which halfword of the source registers Rn and Rm are used as the first and second
multiply operand:
If X is B, then the bottom halfword, bits [15:0], of Rn is used. If X is T, then the top halfword, bits
[31:16], of Rn is used.
If Y is B, then the bottom halfword, bits [15:0], of Rm is used. If Y is T, then the top halfword, bits
[31:16], of Rm is used.
SMLALD
Signed Multiply Accumulate Long Dual
SMLALDX
Signed Multiply Accumulate Long Dual Reversed
If the X is omitted, the multiplications are bottom × bottom and top × top.
If X is present, the multiplications are bottom × top and top × bottom.
cond
is an optional condition code, see Table 1-2 on page 33.
RdHi, RdLo
are the destination registers. RdLo is the lower 32 bits and RdHi is the upper 32 bits of the
64-bit integer. For SMLAL, SMLALBB, SMLALBT, SMLALTB, SMLALTT, SMLALD and SMLALDX,
they also hold the accumulating value.
November 04, 2011
113
Texas Instruments Incorporated
Multiply and Divide Instructions
Rn, Rm
are registers holding the first and second operands.
4.4.2
Operation
The SMLAL instruction:
■ Multiplies the two’s complement signed word values from Rn and Rm.
■ Adds the 64-bit value in RdLo and RdHi to the resulting 64-bit product.
■ Writes the 64-bit result of the multiplication and addition in RdLo and RdHi.
The SMLALBB, SMLALBT, SMLALTB and SMLALTT instructions:
■ Multiplies the specified signed halfword, Top or Bottom, values from Rn and Rm.
■ Adds the resulting sign-extended 32-bit product to the 64-bit value in RdLo and RdHi.
■ Writes the 64-bit result of the multiplication and addition in RdLo and RdHi.
The non-specified halfwords of the source registers are ignored.
The SMLALD and SMLALDX instructions interpret the values from Rn and Rm as four halfword two’s
complement signed 16-bit integers. These instructions:
■ if X is not present, multiply the top signed halfword value of Rn with the top signed halfword of
Rm and the bottom signed halfword values of Rn with the bottom signed halfword of Rm.
■ Or if X is present, multiply the top signed halfword value of Rn with the bottom signed halfword
of Rm and the bottom signed halfword values of Rn with the top signed halfword of Rm.
■ Add the two multiplication results to the signed 64-bit value in RdLo and RdHi to create the
resulting 64-bit product.
■ Write the 64-bit product in RdLo and RdHi.
4.4.3
Restrictions
In these instructions:
■ do not use SP and do not use PC.
■ RdHi and RdLo must be different registers.
4.4.4
Condition flags
These instructions do not affect the condition code flags.
4.4.5
Examples
SMLAL
R4, R5, R3, R8
; Multiplies R3 and R8, adds R5:R4 and writes to
; R5:R4
SMLALBT
R2, R1, R6, R7
; Multiplies bottom halfword of R6 with top
; halfword of R7, sign extends to 32-bit, adds
114
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
; R1:R2 and writes to R1:R2
SMLALTB
R2, R1, R6, R7
; Multiplies top halfword of R6 with bottom
; halfword of R7,sign extends to 32-bit, adds R1:R2
; and writes to R1:R2
SMLALD
R6, R8, R5, R1
; Multiplies top halfwords in R5 and R1 and bottom
; halfwords of R5 and R1, adds R8:R6 and writes to
; R8:R6
SMLALDX
R6, R8, R5, R1
; Multiplies top halfword in R5 with bottom
; halfword of R1, and bottom halfword of R5 with
; top halfword of R1, adds R8:R6 and writes to
; R8:R6
November 04, 2011
115
Texas Instruments Incorporated
Multiply and Divide Instructions
4.5
SMLSD and SMLSLD
Signed Multiply Subtract Dual and Signed Multiply Subtract Long Dual.
Applies to...
4.5.1
M3
M4
M4F
✓
✓
Syntax
op{X}{cond} Rd, Rn, Rm, Ra
where:
op
is one of:
SMLSD
Signed Multiply Subtract Dual.
SMLSLD
Signed Multiply Subtract Long Dual.
X
If X is present, the multiplications are bottom × top and top × bottom. If the X is omitted, the
multiplications are bottom × bottom and top × top.
cond
is an optional condition code, see Table 1-2 on page 33.
Rd
is the destination register.
Rn, Rm
are registers holding the first and second operands.
Ra
is the register holding the accumulate value.
4.5.2
Operation
The SMLSD instruction interprets the values from the first and second operands as four signed
halfwords. This instruction:
■ Optionally rotates the halfwords of the second operand.
■ Performs two signed 16 × 16-bit halfword multiplications.
■ Subtracts the result of the upper halfword multiplication from the result of the lower halfword
multiplication.
■ Adds the signed accumulate value to the result of the subtraction.
■ Writes the result of the addition to the destination register.
The SMLSLD instruction interprets the values from Rn and Rm as four signed halfwords. This
instruction:
■ Optionally rotates the halfwords of the second operand.
116
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
■ Performs two signed 16 × 16-bit halfword multiplications.
■ Subtracts the result of the upper halfword multiplication from the result of the lower halfword
multiplication.
■ Adds the 64-bit value in RdHi and RdLo to the result of the subtraction.
■ Writes the 64-bit result of the addition to the RdHi and RdLo.
4.5.3
Restrictions
In these instructions:
■ Do not use SP and do not use PC.
4.5.4
Condition flags
This instruction sets the Q flag if the accumulate operation overflows. Overflow cannot occur during
the multiplications or subtraction.
For the Thumb instruction set, these instructions do not affect the condition code flags.
4.5.5
Examples
SMLSD
R0, R4, R5, R6
; Multiplies bottom halfword of R4 with bottom
; halfword of R5, multiplies top halfword of R4
; with top halfword of R5, subtracts second from
; first, adds R6, writes to R0
SMLSDX
R1, R3, R2, R0
; Multiplies bottom halfword of R3 with top
; halfword of R2, multiplies top halfword of R3
; with bottom halfword of R2, subtracts second from
; first, adds R0, writes to R1
SMLSLD
R3, R6, R2, R7
; Multiplies bottom halfword of R6 with bottom
; halfword of R2, multiplies top halfword of R6
; with top halfword of R2, subtracts second from
; first, adds R6:R3, writes to R6:R3
November 04, 2011
117
Texas Instruments Incorporated
Multiply and Divide Instructions
SMLSLDX
R3, R6, R2, R7
; Multiplies bottom halfword of R6 with top
; halfword of R2, multiplies top halfword of R6
; with bottom halfword of R2, subtracts second from
; first, adds R6:R3, writes to R6:R3
118
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
4.6
SMMLA and SMMLS
Signed Most Significant Word Multiply Accumulate and Signed Most Significant Word Multiply
Subtract.
Applies to...
4.6.1
M3
M4
M4F
✓
✓
Syntax
op{R}{cond} Rd, Rn, Rm, Ra
where:
op
is one of:
SMMLA
Signed Most Significant Word Multiply Accumulate.
SMMLS
Signed Most Significant Word Multiply Subtract.
R
is a rounding error flag. If R is specified, the result is rounded instead of being truncated. In this
case the constant 0x80000000 is added to the product before the high word is extracted.
cond
is an optional condition code, see Table 1-2 on page 33.
Rd
is the destination register.
Rn, Rm
are registers holding the first and second multiply operands.
Ra
is the register holding the accumulate value.
4.6.2
Operation
The SMMLA instruction interprets the values from Rn and Rm as signed 32-bit words.
The SMMLA instruction:
■
■
■
■
■
Multiplies the values in Rn and Rm.
Optionally rounds the result by adding 0x80000000.
Extracts the most significant 32 bits of the result.
Adds the value of Ra to the signed extracted value.
Writes the result of the addition in Rd.
The SMMLS instruction interprets the values from Rn and Rm as signed 32-bit words.
The SMMLS instruction:
November 04, 2011
119
Texas Instruments Incorporated
Multiply and Divide Instructions
■
■
■
■
■
4.6.3
Multiplies the values in Rn and Rm.
Optionally rounds the result by adding 0x80000000.
Extracts the most significant 32 bits of the result.
Subtracts the extracted value of the result from the value in Ra.
Writes the result of the subtraction in Rd.
Restrictions
In these instructions:
■ Do not use SP and do not use PC.
4.6.4
Condition flags
These instructions do not affect the condition code flags.
4.6.5
Examples
SMMLA
R0, R4, R5, R6
; Multiplies R4 and R5, extracts top 32 bits, adds
; R6, truncates and writes to R0
SMMLAR
R6, R2, R1, R4
; Multiplies R2 and R1, extracts top 32 bits, adds
; R4, rounds and writes to R6
SMMLSR
R3, R6, R2, R7
; Multiplies R6 and R2, extracts top 32 bits,
; subtracts R7, rounds and writes to R3
SMMLS
R4, R5, R3, R8
; Multiplies R5 and R3, extracts top 32 bits,
; subtracts R8, truncates and writes to R4
120
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
4.7
SMMUL
Signed Most Significant Word Multiply.
Applies to...
4.7.1
M3
M4
M4F
✓
✓
Syntax
op{R}{cond} Rd, Rn, Rm
where:
op
is one of:
SMMUL
Signed Most Significant Word Multiply
R
is a rounding error flag. If R is specified, the result is rounded instead of being truncated. In this
case the constant 0x80000000 is added to the product before the high word is extracted.
cond
is an optional condition code, see Table 1-2 on page 33.
Rd
is the destination register.
Rn, Rm
are registers holding the first and second operands.
4.7.2
Operation
The SMMUL instruction interprets the values from Rn and Rm as two’s complement 32-bit signed
integers. The SMMUL instruction:
■ Multiplies the values from Rn and Rm.
■ Optionally rounds the result, otherwise truncates the result.
■ Writes the most significant signed 32 bits of the result in Rd.
4.7.3
Restrictions
In this instruction:
■ do not use SP and do not use PC.
4.7.4
Condition flags
This instruction does not affect the condition code flags.
November 04, 2011
121
Texas Instruments Incorporated
Multiply and Divide Instructions
4.7.5
Examples
SMULL
R0, R4, R5
; Multiplies R4 and R5, truncates top 32 bits
; and writes to R0
SMULLR
R6, R2
; Multiplies R6 and R2, rounds the top 32 bits
; and writes to R6
122
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
4.8
SMUAD and SMUSD
Signed Dual Multiply Add and Signed Dual Multiply Subtract.
Applies to...
4.8.1
M3
M4
M4F
✓
✓
Syntax
op{X}{cond} Rd, Rn, Rm
where:
op
is one of:
SMUAD
Signed Dual Multiply Add.
SMUSD
Signed Dual Multiply Subtract.
X
If X is present, the multiplications are bottom × top and top × bottom. If the X is omitted, the
multiplications are bottom × bottom and top × top.
cond
is an optional condition code, see Table 1-2 on page 33.
Rd
is the destination register.
Rn, Rm
are registers holding the first and the second operands.
4.8.2
Operation
The SMUAD instruction interprets the values from the first and second operands as two signed
halfwords in each operand. This instruction:
■
■
■
■
Optionally rotates the halfwords of the second operand.
Performs two signed 16 × 16-bit multiplications.
Adds the two multiplication results together.
Writes the result of the addition to the destination register.
The SMUSD instruction interprets the values from the first and second operands as two’s complement
signed integers. This instruction:
■ Optionally rotates the halfwords of the second operand.
■ Performs two signed 16 × 16-bit multiplications.
■ Subtracts the result of the top halfword multiplication from the result of the bottom halfword
multiplication.
■ Writes the result of the subtraction to the destination register.
November 04, 2011
123
Texas Instruments Incorporated
Multiply and Divide Instructions
4.8.3
Restrictions
In these instructions:
■ Do not use SP and do not use PC.
4.8.4
Condition flags
Sets the Q flag if the addition overflows. The multiplications cannot overflow.
4.8.5
Examples
SMUAD
R0, R4, R5
; Multiplies bottom halfword of R4 with the bottom
; halfword of R5, adds multiplication of top halfword
; of R4 with top halfword of R5, writes to R0
SMUADX
R3, R7, R4
; Multiplies bottom halfword of R7 with top halfword
; of R4, adds multiplication of top halfword of R7
; with bottom halfword of R4, writes to R3
SMUSD
R3, R6, R2
; Multiplies bottom halfword of R4 with bottom halfword
; of R6, subtracts multiplication of top halfword of R6
; with top halfword of R3, writes to R3
SMUSDX
R4, R5, R3
; Multiplies bottom halfword of R5 with top halfword of
; R3, subtracts multiplication of top halfword of R5
; with bottom halfword of R3, writes to R4
124
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
4.9
SMUL and SMULW
Signed Multiply (halfwords) and Signed Multiply (word by halfword).
Applies to...
4.9.1
M3
M4
M4F
✓
✓
Syntax
SMUL{X}{Y}{cond} Rd,Rn, Rm
SMULW{Y}{cond} Rd. Rn, Rm
For SMULXY only:
op
is one of:
SMUL{X}{Y} Signed Multiply (halfwords)
X and Y specify which halfword of the source registers Rn and Rm is used as the first and second
multiply operand. If X is B, then the bottom halfword, bits [15:0] of Rn is used. If X is T, then the
top halfword, bits [31:16] of Rn is used.If Y is B, then the bottom halfword, bits [15:0], of Rm is
used. If Y is T, then the top halfword, bits [31:16], of Rm is used.
SMULW{Y} Signed Multiply (word by halfword)
Y specifies which halfword of the source register Rm is used as the second multiply operand. If
Y is B, then the bottom halfword (bits [15:0]) of Rm is used. If Y is T, then the top halfword (bits
[31:16]) of Rm is used.
cond
is an optional condition code, see Table 1-2 on page 33.
Rd
is the destination register.
Rn, Rm
are registers holding the first and second operands.
4.9.2
Operation
The SMULBB, SMULTB, SMULBT and SMULTT instructions interprets the values from Rn and Rm as
four signed 16-bit integers. These instructions:
■ Multiplies the specified signed halfword, Top or Bottom, values from Rn and Rm.
■ Writes the 32-bit result of the multiplication in Rd.
The SMULWT and SMULWB instructions interprets the values from Rn as a 32-bit signed integer and
Rm as two halfword 16-bit signed integers. These instructions:
■ Multiplies the first operand and the top, T suffix, or the bottom, B suffix, halfword of the second
operand.
November 04, 2011
125
Texas Instruments Incorporated
Multiply and Divide Instructions
■ Writes the signed most significant 32 bits of the 48-bit result in the destination register.
4.9.3
Restrictions
In these instructions:
■ Do not use SP and do not use PC.
■ RdHi and RdLo must be different registers.
4.9.4
Examples
SMULBT
R0, R4, R5
; Multiplies the bottom halfword of R4 with the
; top halfword of R5, multiplies results and
; writes to R0
SMULBB
R0, R4, R5
; Multiplies the bottom halfword of R4 with the
; bottom halfword of R5, multiplies results and
; writes to R0
SMULTT
R0, R4, R5
; Multiplies the top halfword of R4 with the top
; halfword of R5, multiplies results and writes
SMULTB
R0, R4, R5
; to R0
; Multiplies the top halfword of R4 with the
; bottom halfword of R5, multiplies results and
; and writes to R0
SMULWT
R4, R5, R3
; Multiplies R5 with the top halfword of R3,
; extracts top 32 bits and writes to R4
SMULWB
R4, R5, R3
; Multiplies R5 with the bottom halfword of R3,
126
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
; extracts top 32 bits and writes to R4
November 04, 2011
127
Texas Instruments Incorporated
Multiply and Divide Instructions
4.10
UMULL, UMAAL, UMLAL, SMULL, and SMLAL
Signed and Unsigned Long Multiply, with optional Accumulate, using 32-bit operands and producing
a 64-bit result.
UMULL, UMLAL,
SMULL, SMLAL
Applies to...
4.10.1
M3
M4
M4F
✓
✓
✓
UMAAL
M3
M4
M4F
✓
✓
Syntax
{cond} RdLo, RdHi, Rn, Rm
where:
op
is one of:
UMULL
Unsigned Long Multiply.
UMAAL
Unsigned Long Multiply with Accumulate Accumulate.
UMLAL
Unsigned Long Multiply, with Accumulate.
SMULL
Signed Long Multiply.
SMLAL
Signed Long Multiply, with Accumulate.
cond
is an optional condition code, see Table 1-2 on page 33.
RdHi, RdLo
are the destination registers. For UMLAL and SMLAL they also hold the accumulating value.
Rn, Rm
are registers holding the operands.
4.10.2
Operation
The UMULL instruction interprets the values from Rn and Rm as unsigned integers. It multiplies these
integers and places the least significant 32 bits of the result in RdLo, and the most significant 32
bits of the result in RdHi.
The UMAAL instruction interprets the values from Rn and Rm as unsigned integers. It multiplies the
two unsigned integers in the first and second operands and adds the unsigned 32-bit integer in RdHi
to the 64-bit result of the multiplication. It adds the unsigned 32-bit integer in RdLo to the 64-bit
result of the addition, writes the top 32-bits of the result to RdHi, and writes the lower 32-bits of the
result to RdLo.
128
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
The UMLAL instruction interprets the values from Rn and Rm as unsigned integers. It multiplies these
integers, adds the 64-bit result to the 64-bit unsigned integer contained in RdHi and RdLo, and
writes the result back to RdHi and RdLo.
The SMULL instruction interprets the values from Rn and Rm as two’s complement signed integers.
It multiplies these integers and places the least significant 32 bits of the result in RdLo, and the most
significant 32 bits of the result in RdHi.
The SMLAL instruction interprets the values from Rn and Rm as two’s complement signed integers.
It multiplies these integers, adds the 64-bit result to the 64-bit signed integer contained in RdHi and
RdLo, and writes the result back to RdHi and RdLo.
4.10.3
Restrictions
In these instructions:
■ do not use SP and do not use PC
■ RdHi and RdLo must be different registers.
4.10.4
Condition flags
These instructions do not affect the condition code flags.
4.10.5
Examples
UMULL
SMLAL
UMAAL
R0, R4, R5, R6
R4, R5, R3, R8
R3, R6, R2, R7
;
;
;
;
Unsigned (R4,R0) = R5 x R6
Signed (R5,R4) = (R5,R4) + R3 x R8
Multiplies R2 and R7, adds R6, adds R3, writes t
top 32 bits to R6, and the bottom 32 bits to R3.
November 04, 2011
129
Texas Instruments Incorporated
Multiply and Divide Instructions
4.11
SDIV and UDIV
Signed Divide and Unsigned Divide.
Applies to...
4.11.1
M3
M4
M4F
✓
✓
✓
Syntax
SDIV{cond} {Rd,} Rn, Rm
UDIV{cond} {Rd,} Rn, Rm
where:
cond
Is an optional condition code. See Table 1-2 on page 33.
Rd
Is the destination register. If Rd is omitted, the destination register is Rn.
Rn
Is the register holding the value to be divided.
Rm
Is a register holding the divisor.
4.11.2
Operation
SDIV performs a signed integer division of the value in Rn by the value in Rm.
UDIV performs an unsigned integer division of the value in Rn by the value in Rm.
For both instructions, if the value in Rn is not divisible by the value in Rm, the result is rounded
towards zero.
4.11.3
Restrictions
Do not use SP and do not use PC.
4.11.4
Condition Flags
These instructions do not change the flags.
4.11.5
Examples
SDIV
UDIV
R0, R2, R4
R8, R8, R1
; Signed divide, R0 = R2/R4.
; Unsigned divide, R8 = R8/R1.
130
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
5
Saturating Instructions
Table 5-1 on page 131 shows the saturating instructions:
Table 5-1. Saturating Instructions
Mnemonic
Brief Description
SSAT
Signed saturate
132
SSAT16
Signed saturate halfword
134
USAT
Unsigned saturate
132
USAT16
Unsigned saturate halfword
134
QADD
Saturating add
136
QADD8
Saturating add 8
136
QADD16
Saturating add 16
136
QSUB
Saturating subtract
136
QSUB8
Saturating subtract 8
136
QSUB16
Saturating subtract 16
136
QASX
Saturating add and subtract with exchange
138
QSAX
Saturating subtract and add with exchange
138
QDADD
Saturating double and add
140
QDSUB
Saturating double and subtract
140
UQADD16
Unsigned saturating add 16
144
UQADD8
Unsigned saturating add 8
144
UQASX
Unsigned saturating add and subtract with exchange
142
UQSAX
Unsigned saturating subtract and add with exchange
142
UQSUB16
Unsigned saturating subtract 16
144
UQSUB8
Unsigned saturating subtract 8
144
November 04, 2011
See Page
131
Texas Instruments Incorporated
Saturating Instructions
5.1
SSAT and USAT
Signed Saturate and Unsigned Saturate to any bit position, with optional shift before saturating.
Applies to...
5.1.1
M3
M4
M4F
✓
✓
✓
Syntax
op{cond} Rd, #n, Rm {, shift #s}
where:
op
Is one of:
SSAT
Saturates a signed value to a signed range.
USAT
Saturates a signed value to an unsigned range.
cond
Is an optional condition code. See Table 1-2 on page 33.
Rd
Is the destination register.
n
Specifies the bit position to saturate to:
■ n ranges from 1 to 32 for SSAT
■ n ranges from 0 to 31 for USAT
Rm
Is the register containing the value to saturate.
shift #s
Is an optional shift applied to Rm before saturating. It must be one of the following:
ASR #s
Where s is in the range 1 to 31.
LSL #s
Where s is in the range 0 to 31.
5.1.2
Operation
These instructions saturate to a signed or unsigned n-bit value.
The SSAT instruction applies the specified shift, then saturates to the signed range −2n–1 ≤ x ≤ 2n–1−1.
The USAT instruction applies the specified shift, then saturates to the unsigned range 0 ≤ x ≤ 2n−1.
For signed n-bit saturation using SSAT, this means that:
■ If the value to be saturated is less than −2n−1, the result returned is −2n-1.
132
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
■ If the value to be saturated is greater than 2n−1−1, the result returned is 2n-1−1.
■ Otherwise, the result returned is the same as the value to be saturated.
For unsigned n-bit saturation using USAT, this means that:
■ If the value to be saturated is less than 0, the result returned is 0.
■ If the value to be saturated is greater than 2n−1, the result returned is 2n−1.
■ Otherwise, the result returned is the same as the value to be saturated.
If the returned result is different from the value to be saturated, it is called saturation. If saturation
occurs, the instruction sets the Q flag to 1 in the APSR. Otherwise, it leaves the Q flag unchanged.
To clear the Q flag to 0, you must use the MSR instruction. See “MSR” on page 215.
To read the state of the Q flag, use the MRS instruction. See “MRS” on page 214.
5.1.3
Restrictions
Do not use SP and do not use PC.
5.1.4
Condition Flags
These instructions do not affect the condition code flags.
If saturation occurs, these instructions set the Q flag to 1.
5.1.5
Examples
SSAT
R7, #16, R7, LSL #4
USATNE
R0, #7, R5
;
;
;
;
;
Logical shift left value in R7 by 4, then
saturate it as a signed 16-bit value and
write it back to R7.
Conditionally saturate value in R5 as an
unsigned 7 bit value and write it to R0.
November 04, 2011
133
Texas Instruments Incorporated
Saturating Instructions
5.2
SSAT16 and USAT16
Signed Saturate and Unsigned Saturate to any bit position for two halfwords.
Applies to...
5.2.1
M3
M4
M4F
✓
✓
Syntax
op{cond} Rd, #n, Rm
where:
op
is one of:
SSAT16
Saturates a signed halfword value to a signed range.
USAT16
Saturates a signed halfword value to an unsigned range.
cond
is an optional condition code, see Table 1-2 on page 33.
Rd
is the destination register.
n
specifies the bit position to saturate to:
■ n ranges from 1 to 16 for SSAT.
■ n ranges from 0 to 15 for USAT.
Rm
is the register containing the value to saturate.
5.2.2
Operation
The SSAT16 instruction:
1. Saturates two signed 16-bit halfword values of the register with the value to saturate from
selected by the bit position in n.
2. Writes the results as two signed 16-bit halfwords to the destination register.
The USAT16 instruction:
1. Saturates two unsigned 16-bit halfword values of the register with the value to saturate from
selected by the bit position in n.
2. Writes the results as two unsigned halfwords in the destination register.
5.2.3
Restrictions
Do not use SP and do not use PC.
134
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
5.2.4
Condition flags
These instructions do not affect the condition code flags.
If saturation occurs, these instructions set the Q flag to 1.
5.2.5
Examples
SSAT16
R7, #9, R2
; Saturates the top and bottom highwords of R2
; as 9-bit values, writes to corresponding halfword
; of R7
USAT16NE
R0, #13, R5
; Conditionally saturates the top and bottom
; halfwords of R5 as 13-bit values, writes to
; corresponding halfword of R0
November 04, 2011
135
Texas Instruments Incorporated
Saturating Instructions
5.3
QADD and QSUB
Saturating Add and Saturating Subtract, signed.
Applies to...
5.3.1
M3
M4
M4F
✓
✓
Syntax
op{cond} {Rd}, Rn, Rm
op{cond} {Rd}, Rn, Rm
where:
op
is one of:
QADD
Saturating 32-bit add.
QADD8
Saturating four 8-bit integer additions.
QADD16
Saturating two 16-bit integer additions.
QSUB
Saturating 32-bit subtraction.
QSUB8
Saturating four 8-bit integer subtraction.
QSUB16
Saturating two 16-bit integer subtraction.
cond
is an optional condition code, see Table 1-2 on page 33.
Rd
is the destination register.
Rn, Rm
are registers holding the first and second operands.
5.3.2
Operation
These instructions add or subtract two, four or eight values from the first and second operands and
then writes a signed saturated value in the destination register.
The QADD and QSUB instructions apply the specified add or subtract, and then saturate the result
to the signed range −2n–1 ≤ x ≤ 2n–1−1, where x is given by the number of bits applied in the
instruction, 32, 16 or 8.
136
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
If the returned result is different from the value to be saturated, it is called saturation. If saturation
occurs, the QADD and QSUB instructions set the Q flag to 1 in the APSR. Otherwise, it leaves the Q
flag unchanged. The 8-bit and 16-bit QADD and QSUB instructions always leave the Q flag unchanged.
To clear the Q flag to 0, you must use the MSR instruction, see 215.
To read the state of the Q flag, use the MRS instruction, see 214.
5.3.3
Restrictions
Do not use SP and do not use PC.
5.3.4
Condition flags
These instructions do not affect the condition code flags.
If saturation occurs, these instructions set the Q flag to 1.
5.3.5
Examples
QADD16
R7, R4, R2
; Adds halfwords of R4 with corresponding halfword of
; R2, saturates to 16 bits and writes to corresponding
; halfword of R7
QADD8
R3, R1, R6
; Adds bytes of R1 to the corresponding bytes of R6,
; saturates to 8 bits and writes to corresponding byte of
; R3
QSUB16
R4, R2, R3
; Subtracts halfwords of R3 from corresponding halfword
; of R2, saturates to 16 bits, writes to corresponding
; halfword of R4
QSUB8
R4, R2, R5
; Subtracts bytes of R5 from the corresponding byte in
; R2, saturates to 8 bits, writes to corresponding byte of
; R4
November 04, 2011
137
Texas Instruments Incorporated
Saturating Instructions
5.4
QASX and QSAX
Saturating Add and Subtract with Exchange and Saturating Subtract and Add with Exchange, signed.
Applies to...
5.4.1
M3
M4
M4F
✓
✓
Syntax
op{cond} {Rd}, Rm, Rn
where:
op
is one of:
QASX
Add and Subtract with Exchange and Saturate.
QSAX
Subtract and Add with Exchange and Saturate.
cond
is an optional condition code, see Table 1-2 on page 33.
Rd
is the destination register.
Rn, Rm
are registers holding the first and second operands.
5.4.2
Operation
The QASX instruction:
1. Adds the top halfword of the source operand with the bottom halfword of the second operand.
2. Subtracts the top halfword of the second operand from the bottom highword of the first operand.
3. Saturates the result of the subtraction and writes a 16-bit signed integer in the range –215 ≤ x
≤ 215 – 1, where x equals 16, to the bottom halfword of the destination register.
4. Saturates the results of the sum and writes a 16-bit signed integer in the range –215 ≤ x ≤ 215
– 1, where x equals 16, to the top halfword of the destination register.
The QSAX instruction:
1. Subtracts the bottom halfword of the second operand from the top highword of the first operand.
2. Adds the bottom halfword of the source operand with the top halfword of the second operand.
3. Saturates the results of the sum and writes a 16-bit signed integer in the range –215 ≤ x ≤ 215
– 1, where x equals 16, to the bottom halfword of the destination register.
4. Saturates the result of the subtraction and writes a 16-bit signed integer in the range –215 ≤ x
≤ 215 – 1, where x equals 16, to the top halfword of the destination register.
5.4.3
Restrictions
Do not use SP and do not use PC.
138
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
5.4.4
Condition flags
These instructions do not affect the condition code flags.
5.4.5
Examples
QASX
R7, R4, R2
; Adds top halfword of R4 to bottom halfword of R2,
; saturates to 16 bits, writes to top halfword of R7
; Subtracts top highword of R2 from bottom halfword of
; R4, saturates to 16 bits and writes to bottom halfword
; of R7
QSAX
R0, R3, R5
; Subtracts bottom halfword of R5 from top halfword of
; R3, saturates to 16 bits, writes to top halfword of R0
; Adds bottom halfword of R3 to top halfword of R5,
; saturates to 16 bits, writes to bottom halfword of R0
November 04, 2011
139
Texas Instruments Incorporated
Saturating Instructions
5.5
QDADD and QDSUB
Saturating Double and Add and Saturating Double and Subtract, signed.
Applies to...
5.5.1
M3
M4
M4F
✓
✓
Syntax
op{cond} {Rd}, Rm, Rn
where:
op
is one of:
QDADD
Saturating Double and Add.
QDSUB
Saturating Double and Subtract.
cond
is an optional condition code, see Table 1-2 on page 33.
Rd
is the destination register.
Rm, Rn
are registers holding the first and second operands.
5.5.2
Operation
The QDADD instruction:
■ Doubles the second operand value.
■ Adds the result of the doubling to the signed saturated value in the first operand.
■ Writes the result to the destination register.
The QDSUB instruction:
■ Doubles the second operand value.
■ Subtracts the doubled value from the signed saturated value in the first operand.
■ Writes the result to the destination register.
Both the doubling and the addition or subtraction have their results saturated to the 32-bit signed
integer range –231 ≤ x ≤ 231– 1. If saturation occurs in either operation, it sets the Q flag in the
APSR.
5.5.3
Restrictions
Do not use SP and do not use PC.
140
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
5.5.4
Condition flags
If saturation occurs, these instructions set the Q flag to 1.
5.5.5
Examples
QDADD
R7, R4, R2
; Doubles and saturates R4 to 32 bits, adds R2,
; saturates to 32 bits, writes to R7.
QDSUB
R0, R3, R5
; Subtracts R3 doubled and saturated to 32 bits
; from R5, saturates to 32 bits, writes to R0.
November 04, 2011
141
Texas Instruments Incorporated
Saturating Instructions
5.6
UQASX and UQSAX
Saturating Add and Subtract with Exchange and Saturating Subtract and Add with Exchange,
unsigned.
Applies to...
5.6.1
M3
M4
M4F
✓
✓
Syntax
op{cond} {Rd}, Rm, Rn
where:
type
is one of:
UQASX
Add and Subtract with Exchange and Saturate.
UQSAX
Subtract and Add with Exchange and Saturate.
cond
is an optional condition code, see Table 1-2 on page 33.
Rd
is the destination register.
Rn, Rm
are registers holding the first and second operands.
5.6.2
Operation
The UQASX instruction:
1. Adds the bottom halfword of the source operand with the top halfword of the second operand.
2. Subtracts the bottom halfword of the second operand from the top highword of the first operand.
3. Saturates the results of the sum and writes a 16-bit unsigned integer in the range 0 ≤ x ≤ 216
– 1, where x equals 16, to the top halfword of the destination register.
4. Saturates the result of the subtraction and writes a 16-bit unsigned integer in the range 0 ≤ x ≤
216 – 1, where x equals 16, to the bottom halfword of the destination register.
The UQSAX instruction:
1. Subtracts the bottom halfword of the second operand from the top highword of the first operand.
2. Adds the bottom halfword of the first operand with the top halfword of the second operand.
3. Saturates the result of the subtraction and writes a 16-bit unsigned integer in the range 0 ≤ x ≤
216 – 1, where x equals 16, to the top halfword of the destination register.
4. Saturates the results of the addition and writes a 16-bit unsigned integer in the range 0 ≤ x ≤
216 – 1, where x equals 16, to the bottom halfword of the destination register.
142
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
5.6.3
Restrictions
Do not use SP and do not use PC.
5.6.4
Condition flags
These instructions do not affect the condition code flags.
5.6.5
Examples
UQASX
R7, R4, R2
; Adds top halfword of R4 with bottom halfword of R2,
; saturates to 16 bits, writes to top halfword of R7
; Subtracts top halfword of R2 from bottom halfword of
; R4, saturates to 16 bits, writes to bottom halfword of R7
UQSAX
R0, R3, R5
; Subtracts bottom halfword of R5 from top halfword of R3,
; saturates to 16 bits, writes to top halfword of R0
; Adds bottom halfword of R4 to top halfword of R5
; saturates to 16 bits, writes to bottom halfword of R0.
November 04, 2011
143
Texas Instruments Incorporated
Saturating Instructions
5.7
UQADD and UQSUB
Saturating Add and Saturating Subtract Unsigned.
Applies to...
5.7.1
M3
M4
M4F
✓
✓
Syntax
op{cond} {Rd}, Rn, Rm
op{cond} {Rd}, Rn, Rm
where:
op
is one of:
UQADD8
Saturating four unsigned 8-bit integer additions.
UQADD16
Saturating two unsigned 16-bit integer additions.
UDSUB8
Saturating four unsigned 8-bit integer subtractions.
UQSUB16
Saturating two unsigned 16-bit integer subtractions.
cond
is an optional condition code, see Table 1-2 on page 33.
Rd
is the destination register.
Rn, Rm
are registers holding the first and second operands.
5.7.2
Operation
These instructions add or subtract two or four values and then writes an unsigned saturated value
in the destination register.
The UQADD16 instruction:
■ Adds the respective top and bottom halfwords of the first and second operands.
■ Saturates the result of the additions for each halfword in the destination register to the unsigned
range 0 ≤ x ≤ 216−1, where x is 16.
The UQADD8 instruction:
■ Adds each respective byte of the first and second operands.
144
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
■ Saturates the result of the addition for each byte in the destination register to the unsigned range
0 ≤ x ≤ 28−1, where x is 8.
The UQSUB16 instruction:
■ Subtracts both halfwords of the second operand from the respective halfwords of the first operand.
■ Saturates the result of the differences in the destination register to the unsigned range
0 ≤ x ≤ 216−1, where x is 16.
The UQSUB8 instructions:
■ Subtracts the respective bytes of the second operand from the respective bytes of the first
operand.
■ Saturates the results of the differences for each byte in the destination register to the unsigned
range 0 ≤ x ≤ 28−1, where x is 8.
5.7.3
Restrictions
Do not use SP and do not use PC.
5.7.4
Condition flags
These instructions do not affect the condition code flags.
5.7.5
Examples
UQADD16
R7, R4, R2
; Adds halfwords in R4 to corresponding halfword in R2,
; saturates to 16 bits, writes to corresponding halfword
; of R7
UQADD8
R4, R2, R5
; Adds bytes of R2 to corresponding byte of R5, saturates
; to 8 bits, writes to corresponding bytes of R4
UQSUB16
R6, R3, R0
; Subtracts halfwords in R0 from corresponding halfword
; in R3, saturates to 16 bits, writes to corresponding
; halfword in R6
UQSUB8
R1, R5, R6
; Subtracts bytes in R6 from corresponding byte of R5,
; saturates to 8 bits, writes to corresponding byte of R1
November 04, 2011
145
Texas Instruments Incorporated
Saturating Instructions
146
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
6
Packing and Unpacking Instructions
Table 6-1 on page 147 shows the packing and unpacking instructions:
Table 6-1. Packing and Unpacking Instructions
Mnemonic
Brief Description
PKH
Pack halfword
148
SXTAB
Extend 8 bits to 32 and add
154
SXTAB16
Dual extend 8 bits to 16 and add
154
SXTAH
Extend 16 bits to 32 and add
154
SXTB
Sign extend a byte
150
SXTB16
Dual extend 8 bits to 16 and add
150
SXTH
Sign extend a halfword
150
UXTAB
Extend 8 bits to 32 and add
154
UXTAB16
Dual extend 8 bits to 16 and add
154
UXTAH
Extend 16 bits to 32 and add
154
UXTB
Zero extend a byte
150
UXTB16
Dual zero extend 8 bits to 16 and add
150
UXTH
Zero extend a halfword
150
November 04, 2011
See Page
147
Texas Instruments Incorporated
Packing and Unpacking Instructions
6.1
PKHBT and PKHTB
Pack Halfword.
Applies to...
6.1.1
M3
M4
M4F
✓
✓
✓
Syntax
op{cond} {Rd}, Rn, Rm {, LSL #imm}
op{cond} {Rd}, Rn, Rm {, ASR #imm}
where:
op
is one of:
PKHBT
Pack Halfword, bottom and top with shift.
PKHTB
Pack Halfword, top and bottom with shift.
cond
is an optional condition code, see 33.
Rd
is the destination register.
Rn
is the first operand register.
Rm
is the second operand register holding the value to be optionally shifted.
imm
is the shift length. The type of shift length depends on the instruction:For PKHBT
:
LSL
a left shift with a shift length from 1 to 31, 0 means no shift.
For PKHTB:
ASR
an arithmetic shift right with a shift length from 1 to 32, a shift of 32-bits is encoded as
0b00000.
6.1.2
Operation
The PKHBT instruction:
148
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
1. Writes the value of the bottom halfword of the first operand to the bottom halfword of the
destination register.
2. If shifted, the shifted value of the second operand is written to the top halfword of the destination
register.
The PKHTB instruction:
1. Writes the value of the top halfword of the first operand to the top halfword of the destination
register.
2. If shifted, the shifted value of the second operand is written to the bottom halfword of the
destination register.
6.1.3
Restrictions
Rd must not be SP and must not be PC.
6.1.4
Condition flags
This instruction does not change the flags.
6.1.5
Examples
PKHBT
R3, R4, R5 LSL #0
; Writes bottom halfword of R4 to bottom halfword of
; R3, writes top halfword of R5, unshifted, to top
; halfword of R3
PKHTB
R4, R0, R2 ASR #1
; Writes R2 shifted right by 1 bit to bottom halfword
; of R4, and writes top halfword of R0 to top
; halfword of R4
November 04, 2011
149
Texas Instruments Incorporated
Packing and Unpacking Instructions
6.2
SXT and UXT
Sign extend and Zero extend.
Applies to...
6.2.1
M3
M4
M4F
✓
✓
✓
Syntax
op{cond} {Rd,} Rm {, ROR #n}
op{cond} {Rd}, Rm {, ROR #n}
where:
op
is one of:
SXTB
Sign extends an 8-bit value to a 32-bit value.
SXTH
Sign extends a 16-bit value to a 32-bit value.
SXTB16
Sign extends two 8-bit values to two 16-bit values.
UXTB
Zero extends an 8-bit value to a 32-bit value.
UXTH
Zero extends a 16-bit value to a 32-bit value.
UXTB16
Zero extends two 8-bit values to two 16-bit values.
cond
is an optional condition code, see 33.
Rd
is the destination register.
Rm
is the register holding the value to extend.
ROR #n
is one of:
ROR #8
Value from Rm is rotated right 8 bits.
ROR #16
Value from Rm is rotated right 16 bits.
150
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
ROR #24
Value from Rm is rotated right 24 bits.
If ROR #n is omitted, no rotation is performed.
6.2.2
Operation
These instructions do the following:
1. Rotate the value from Rm right by 0, 8, 16 or 24 bits.
2. Extract bits from the resulting value:
■
■
■
■
■
SXTB extracts bits[7:0] and sign extends to 32 bits.
UXTB extracts bits[7:0] and zero extends to 32 bits.
SXTH extracts bits[15:0] and sign extends to 32 bits.
UXTH extracts bits[15:0] and zero extends to 32 bits.
SXTB16 extracts bits[7:0] and sign extends to 16 bits, and extracts bits [23:16] and sign
extends to 16 bits.
■ UXTB16 extracts bits[7:0] and zero extends to 16 bits, and extracts bits [23:16] and zero
extends to 16 bits.
6.2.3
Restrictions
Do not use SP and do not use PC.
6.2.4
Condition flags
These instructions do not affect the flags.
6.2.5
Examples
SXTH
R4, R6, ROR #16
UXTB
R3, R10
;
;
;
;
Rotates R6 right by 16 bits, obtains bottom halfword of
of result, sign extends to 32 bits and writes to R4
Extracts lowest byte of value in R10, zero extends, and
writes to R3
November 04, 2011
151
Texas Instruments Incorporated
Packing and Unpacking Instructions
6.3
SXTB16 and UXTB16
Sign extend and Zero extend byte 16.
Applies to...
6.3.1
M3
M4
M4F
✓
✓
Syntax
op{cond} {Rd,} Rm {, ROR #n}
op{cond} {Rd}, Rm {, ROR #n}
where:
op
is one of:
SXTB16
Sign extends two 8-bit values to two 16-bit values.
UXTB16
Zero extends two 8-bit values to two 16-bit values.
cond
is an optional condition code, see 33.
Rd
is the destination register.
Rm
is the register holding the value to extend.
ROR #n
is one of:
ROR #8
Value from Rm is rotated right 8 bits.
ROR #16
Value from Rm is rotated right 16 bits.
ROR #24
Value from Rm is rotated right 24 bits.
If ROR #n is omitted, no rotation is performed.
6.3.2
Operation
These instructions do the following:
1. Rotate the value from Rm right by 0, 8, 16 or 24 bits.
152
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
2. Extract bits from the resulting value:
■ SXTB16 extracts bits[7:0] and sign extends to 16 bits, and extracts bits [23:16] and sign
extends to 16 bits.
■ UXTB16 extracts bits[7:0] and zero extends to 16 bits, and extracts bits [23:16] and zero
extends to 16 bits.
6.3.3
Restrictions
Do not use SP and do not use PC.
6.3.4
Condition flags
These instructions do not affect the flags.
6.3.5
Examples
SXTH
R4, R6, ROR #16
UXTB
R3, R10
;
;
;
;
Rotates R6 right by 16 bits, obtains bottom halfword of
of result, sign extends to 32 bits and writes to R4
Extracts lowest byte of value in R10, zero extends, and
writes to R3
November 04, 2011
153
Texas Instruments Incorporated
Packing and Unpacking Instructions
6.4
SXTA and UXTA
Signed and Unsigned Extend and Add.
Applies to...
6.4.1
M3
M4
M4F
✓
✓
Syntax
op{cond} {Rd,} Rn, Rm {, ROR #n}
op{cond} {Rd,} Rn, Rm {, ROR #n}
where:
op
is one of:
SXTAB
Sign extends an 8-bit value to a 32-bit value and add.
SXTAH
Sign extends a 16-bit value to a 32-bit value and add.
SXTAB16
Sign extends two 8-bit values to two 16-bit values and add.
UXTAB
Zero extends an 8-bit value to a 32-bit value and add.
UXTAH
Zero extends a 16-bit value to a 32-bit value and add.
UXTAB16
Zero extends two 8-bit values to two 16-bit values and add.
cond
is an optional condition code, see 33.
Rd
is the destination register.
Rn
is the first operand register.
Rm
is the register holding the value to rotate and extend.
ROR #n
is one of:
ROR #8
Value from Rm is rotated right 8 bits.
154
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
ROR #16
Value from Rm is rotated right 16 bits.
ROR #24
Value from Rm is rotated right 24 bits.
If ROR #n is omitted, no rotation is performed.
6.4.2
Operation
These instructions do the following:
1. Rotate the value from Rm right by 0, 8, 16 or 24 bits.
2. Extract bits from the resulting value:
■
■
■
■
■
SXTAB extracts bits[7:0] from Rm and sign extends to 32 bits.
UXTAB extracts bits[7:0] from Rm and zero extends to 32 bits.
SXTAH extracts bits[15:0] from Rm and sign extends to 32 bits.
UXTAH extracts bits[15:0] from Rm and zero extends to 32 bits.
SXTAB16 extracts bits[7:0] from Rm and sign extends to 16 bits, and extracts bits [23:16]
from Rm and sign extends to 16 bits.
■ UXTAB16 extracts bits[7:0] from Rm and zero extends to 16 bits, and extracts bits [23:16]
from Rm and zero extends to 16 bits.
3. Adds the signed or zero extended value to the word or corresponding halfword of Rn and writes
the result in Rd.
6.4.3
Restrictions
Do not use SP and do not use PC.
6.4.4
Condition flags
These instructions do not affect the flags.
6.4.5
Examples
SXTAH
UXTAB
R4, R8, R6, ROR #16 ;
;
;
R3, R4, R10
;
;
Rotates R6 right by 16 bits, obtains bottom
halfword, sign extends to 32 bits, adds R8,and
writes to R4
Extracts bottom byte of R10 and zero extends to 32
bits, adds R4, and writes to R3
November 04, 2011
155
Texas Instruments Incorporated
Bitfield Instructions
7
Bitfield Instructions
Table 7-1 on page 156 shows the instructions that operate on adjacent sets of bits in registers or
bitfields:
Table 7-1. Bitfield Instructions
Mnemonic
Brief Description
BFC
Bit field clear
157
BFI
Bit field insert
157
SBFX
Signed bit field extract
158
UBFX
Unsigned bit field extract
158
156
See Page
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
7.1
BFC and BFI
Bit Field Clear and Bit Field Insert.
Applies to...
7.1.1
M3
M4
M4F
✓
✓
✓
Syntax
BFC{cond} Rd, #lsb, #width
BFI{cond} Rd, Rn, #lsb, #width
where:
cond
Is an optional condition code. See Table 1-2 on page 33.
Rd
Is the destination register.
Rn
Is the source register.
lsb
Is the position of the least-significant bit of the bitfield. lsb must be in the range 0 to 31.
width
Is the width of the bitfield and must be in the range 1 to 32 lsb.
7.1.2
Operation
BFC clears a bitfield in a register. It clears width bits in Rd, starting at the low bit position lsb.
Other bits in Rd are unchanged.
BFI copies a bitfield into one register from another register. It replaces width bits in Rd starting at
the low bit position lsb, with width bits from Rn starting at bit[0]. Other bits in Rd are unchanged.
7.1.3
Restrictions
Do not use SP and do not use PC.
7.1.4
Condition Flags
These instructions do not affect the flags.
7.1.5
Examples
BFC
BFI
R4, #8, #12
R9, R2, #8, #12
; Clear bit 8 to bit 19 (12 bits) of R4 to 0.
; Replace bit 8 to bit 19 (12 bits) of R9 with
; bit 0 to bit 11 from R2.
November 04, 2011
157
Texas Instruments Incorporated
Bitfield Instructions
7.2
SBFX and UBFX
Signed Bit Field Extract and Unsigned Bit Field Extract.
Applies to...
7.2.1
M3
M4
M4F
✓
✓
✓
Syntax
SBFX{cond} Rd, Rn, #lsb, #width
UBFX{cond} Rd, Rn, #lsb, #width
where:
cond
Is an optional condition code. See Table 1-2 on page 33.
Rd
Is the destination register.
Rn
Is the source register.
lsb
Is the position of the least-significant bit of the bitfield. lsb must be in the range 0 to 31.
width
Is the width of the bitfield and must be in the range 1 to 32 lsb.
7.2.2
Operation
SBFX extracts a bitfield from one register, sign extends it to 32 bits, and writes the result to the
destination register.
UBFX extracts a bitfield from one register, zero extends it to 32 bits, and writes the result to the
destination register.
7.2.3
Restrictions
Do not use SP and do not use PC.
7.2.4
Condition Flags
These instructions do not affect the flags.
7.2.5
Examples
SBFX
UBFX
R0, R1, #20, #4
;
;
R8, R11, #9, #10 ;
;
Extract bit 20 to bit 23 (4 bits) from R1 and sign
extend to 32 bits and then write the result to R0.
Extract bit 9 to bit 18 (10 bits) from R11 and zero
extend to 32 bits and then write the result to R8.
158
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
8
Floating-Point
1
Table 8-1 on page 159 shows the floating-point instructions:
Table 8-1. Floating-Point Instructions
Mnemonic
Brief Description
VABS
Floating-point absolute
See Page
161
VADD
Floating-point add
162
VCMP
Compare two floating-point registers, or one floating-point
register and zero
163
VCMPE
Compare two floating-point registers, or one floating-point
register and zero with Invalid Operation check
163
VCVT
Convert between floating-point and integer
167
VCVT
Convert between floating-point and fixed point
167
VCVTR
Convert between floating-point and integer with rounding
167
VCVTB
Converts half-precision value to single-precision
169
VCVTT
Converts single-precision register to half-precision
169
VDIV
Floating-point divide
171
VFMA
Floating-point fused multiply accumulate
172
VFNMA
Floating-point fused negate multiply accumulate
173
VFMS
Floating-point fused multiply subtract
172
VFNMS
Floating-point fused negate multiply subtract
173
VLDM
Load multiple extension registers
174
VLDR
Loads an extension register from memory
176
VLMA
Floating-point multiply accumulate
178
VLMS
Floating-point multiply subtract
178
VMOV
Floating-point move immediate
179
VMOV
Floating-point move register
180
VMOV
Copy ARM core register to single precision
182
VMOV
Copy 2 ARM core registers to 2 single precision
183
VMOV
Copies between ARM core register to scalar
182
VMOV
Copies between scalar to ARM core register
182
VMRS
Move to ARM core register from floating-point system register
185
VMSR
Move to floating-point system register from ARM Core register
186
VMUL
Multiply floating-point
187
VNEG
Floating-point negate
188
VNMLA
Floating-point multiply and add
189
VNMLS
Floating-point multiply and subtract
189
VNMUL
Floating-point multiply
189
VPOP
Pop extension registers
191
VPUSH
Push extension registers
192
VSQRT
Floating-point square root
193
1
These instructions are only available if the FPU is included, and enabled, in the system.
November 04, 2011
159
Texas Instruments Incorporated
Floating-Point
Table 8-1. Floating-Point Instructions (continued)
Mnemonic
Brief Description
VSTM
Store multiple extension registers
194
VSTR
Stores an extension register to memory
196
VSUB
Floating-point subtract
197
160
See Page
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
8.1
VABS
Floating-point Absolute.
Applies to...
8.1.1
M3
M4
M4F
✓
Syntax
VABS{cond}.F32 Sd, Sm
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
Sd, Sm
are the destination floating-point value and the operand floating-point value.
8.1.2
Operation
This instruction:
1. Takes the absolute value of the operand floating-point register.
2. Places the results in the destination floating-point register.
8.1.3
Restrictions
There are no restrictions.
8.1.4
Condition flags
The floating-point instruction clears the sign bit.
8.1.5
Examples
VABS.F32 S4, S6
November 04, 2011
161
Texas Instruments Incorporated
Floating-Point
8.2
VADD
Floating-point Add.
Applies to...
8.2.1
M3
M4
M4F
✓
Syntax
VADD{cond}.F32 {Sd,} Sn, Sm
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
Sd
is the destination floating-point value.
Sn, Sm
are the operand floating-point values.
8.2.2
Operation
This instruction:
1. Adds the values in the two floating-point operand registers.
2. Places the results in the destination floating-point register.
8.2.3
Restrictions
There are no restrictions.
8.2.4
Condition flags
This instruction does not change the flags.
8.2.5
Examples
VADD.F32 S4, S6, S7
162
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
8.3
VCMP, VCMPE
Compares two floating-point registers, or one floating-point register and zero.
Applies to...
8.3.1
M3
M4
M4F
✓
Syntax
VCMP{E}{cond}.F32 Sd, Sm
VCMP{E}{cond}.F32 Sd, #0.0
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
E
If present, any NaN operand causes an Invalid Operation exception. Otherwise, only a
signaling NaN causes the exception.
Sd
is the floating-point operand to compare.
Sm
is the floating-point operand that is compared with.
8.3.2
Operation
This instruction:
1. Compares:
■ Two floating-point registers.
■ One floating-point register and zero.
2. Writes the result to the FPSCR flags.
8.3.3
Restrictions
This instruction can optionally raise an Invalid Operation exception if either operand is any
type of NaN. It always raises an Invalid Operation exception if either operand is a signaling
NaN.
8.3.4
Condition flags
When this instruction writes the result to the FPSCR flags, the values are normally transferred to the
ARM flags by a subsequent VMRS instruction, see “VMRS” on page 185.
November 04, 2011
163
Texas Instruments Incorporated
Floating-Point
8.3.5
Examples
VCMP.F32
S4, #0.0VCMP.F32
S4, S2
164
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
8.4
VCVT, VCVTR between floating-point and integer
Converts a value in a register from floating-point to a 32-bit integer.
Applies to...
8.4.1
M3
M4
M4F
✓
Syntax
VCVT{R}{cond}.Tm.F32 Sd, Sm
VCVT{cond}.F32.Tm Sd, Sm
where:
R
If R is specified, the operation uses the rounding mode specified by the FPSCR. If R is omitted.
the operation uses the Round towards Zero rounding mode.
cond
is an optional condition code, see “Conditional Execution” on page 32.
Tm
is the data type for the operand. It must be one of:
■ S32 signed 32-bit value.
■ U32 unsigned 32-bit value.
Sd, Sm
are the destination register and the operand register.
8.4.2
Operation
These instructions:
1. Either
■ Converts a value in a register from floating-point value to a 32-bit integer.
■ Converts from a 32-bit integer to floating-point value.
2. Places the result in a second register.
The floating-point to integer operation normally uses the Round towards Zero rounding mode,
but can optionally use the rounding mode specified by the FPSCR.
The integer to floating-point operation uses the rounding mode specified by the FPSCR.
8.4.3
Restrictions
There are no restrictions.
November 04, 2011
165
Texas Instruments Incorporated
Floating-Point
8.4.4
Condition flags
These instructions do not change the flags.
166
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
8.5
VCVT between floating-point and fixed-point
Converts a value in a register from floating-point to and from fixed-point.
Applies to...
8.5.1
M3
M4
M4F
✓
Syntax
VCVT{cond}.Td.F32 Sd, Sd, #fbits
VCVT{cond}.F32.Td Sd, Sd, #fbits
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
Td
is the data type for the fixed-point number. It must be one of:
■ S16 signed 16-bit value.
■ U16 unsigned 16-bit value.
■ S32 signed 32-bit value.
■ U32 unsigned 32-bit value.
Sd
is the destination register and the operand register.
fbits
is the number of fraction bits in the fixed-point number:
■ If Td is S16 or U16, fbits must be in the range 0-16.
■ I f Td is S32 or U32, fbits must be in the range 1-32.
8.5.2
Operation
These instructions:
1. Either
■ Converts a value in a register from floating-point to fixed-point.
■ Converts a value in a register from fixed-point to floating-point.
2. Places the result in a second register.
The floating-point values are single-precision.
November 04, 2011
167
Texas Instruments Incorporated
Floating-Point
The fixed-point value can be 16-bit or 32-bit. Conversions from fixed-point values take their operand
from the low-order bits of the source register and ignore any remaining bits.
Signed conversions to fixed-point values sign-extend the result value to the destination register
width.
Unsigned conversions to fixed-point values zero-extend the result value to the destination register
width.
The floating-point to fixed-point operation uses the Round towards Zero rounding mode. The
fixed-point to floating-point operation uses the Round to Nearest rounding mode.
8.5.3
Restrictions
There are no restrictions.
8.5.4
Condition flags
These instructions do not change the flags.
168
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
8.6
VCVTB, VCVTT
Converts between a half-precision value and a single-precision value.
Applies to...
8.6.1
M3
M4
M4F
✓
Syntax
VCVT{y}{cond}.F32.F16 Sd, Sm
VCVT{y}{cond}.F16.F32 Sd, Sm
where:
y
Specifies which half of the operand register Sm or destination register Sd is used for the operand
or destination:
■ If y is B, then the bottom half, bits [15:0], of Sm or Sd is used.
■ If y is T, then the top half, bits [31:16], of Sm or Sd is used.
cond
is an optional condition code, see “Conditional Execution” on page 32.
Sd
is the destination register.
Sm
is the operand register.
8.6.2
Operation
This instruction with the .F16.32 suffix:
1. Converts the half-precision value in the top or bottom half of a single-precision. register to
single-precision.
2. Writes the result to a single-precision register.
This instruction with the .F32.F16 suffix:
1. Converts the value in a single-precision register to half-precision.
2. Writes the result into the top or bottom half of a single-precision register, preserving the other
half of the target register.
8.6.3
Restrictions
There are no restrictions.
November 04, 2011
169
Texas Instruments Incorporated
Floating-Point
8.6.4
Condition flags
These instructions do not change the flags.
170
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
8.7
VDIV
Divides floating-point values.
Applies to...
8.7.1
M3
M4
M4F
✓
Syntax
VDIV{cond}.F32 {Sd,} Sn, Sm
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
Sd
is the destination register.
Sn, Sm
are the operand registers.
8.7.2
Operation
This instruction:
1. Divides one floating-point value by another floating-point value.
2. Writes the result to the floating-point destination register.
8.7.3
Restrictions
There are no restrictions.
8.7.4
Condition flags
These instructions do not change the flags.
November 04, 2011
171
Texas Instruments Incorporated
Floating-Point
8.8
VFMA, VFMS
Floating-point Fused Multiply Accumulate and Subtract.
Applies to...
8.8.1
M3
M4
M4F
✓
Syntax
VFMA{cond}.F32 {Sd,} Sn, Sm
VFMS{cond}.F32 {Sd,} Sn, Sm
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
Sd
is the destination register.
Sn, Sm
are the operand registers.
8.8.2
Operation
The VFMA instruction:
1. Multiplies the floating-point values in the operand registers.
2. Accumulates the results into the destination register.
The result of the multiply is not rounded before the accumulation.
The VFMS instruction:
1. Negates the first operand register.
2. Multiplies the floating-point values of the first and second operand registers.
3. Adds the products to the destination register.
4. Places the results in the destination register.
The result of the multiply is not rounded before the addition.
8.8.3
Restrictions
There are no restrictions.
8.8.4
Condition flags
These instructions do not change the flags.
172
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
8.9
VFNMA, VFNMS
Floating-point Fused Negate Multiply Accumulate and Subtract.
Applies to...
8.9.1
M3
M4
M4F
✓
Syntax
VFNMA{cond}.F32 {Sd,} Sn, Sm
VFNMS{cond}.F32 {Sd,} Sn, Sm
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
Sd
is the destination register.
Sn, Sm
are the operand registers.
8.9.2
Operation
The VFNMA instruction:
1. Negates the first floating-point operand register.
2. Multiplies the first floating-point operand with second floating-point operand.
3. Adds the negation of the floating -point destination register to the product
4. Places the result into the destination register.
The result of the multiply is not rounded before the addition.
The VFNMS instruction:
1. Multiplies the first floating-point operand with second floating-point operand.
2. Adds the negation of the floating-point value in the destination register to the product.
3. Places the result in the destination register.
The result of the multiply is not rounded before the addition.
8.9.3
Restrictions
There are no restrictions.
8.9.4
Condition flags
These instructions do not change the flags.
November 04, 2011
173
Texas Instruments Incorporated
Floating-Point
8.10
VLDM
Floating-point Load Multiple.
Applies to...
8.10.1
M3
M4
M4F
✓
Syntax
VLDM{mode}{cond}{.size} Rn{!}, list
where:
mode
is the addressing mode:
■ IA Increment After. The consecutive addresses start at the address specified in Rn.
■ DB Decrement Before. The consecutive addresses end just before
the address specified in Rn.
cond
is an optional condition code, see “Conditional Execution” on page 32.
size
is an optional data size specifier.
Rn
is the base register. The SP can be used.
!
is the command to the instruction to write a modified value back to Rn. This is required if mode
== DB, and is optional if mode == IA.
list
is the list of extension registers to be loaded, as a list of consecutively numbered doubleword
or singleword registers, separated by commas and surrounded by brackets.
8.10.2
Operation
This instruction loads:
■ Multiple extension registers from consecutive memory locations using an address from an ARM
core register as the base address.
8.10.3
Restrictions
The restrictions are:
■ If size is present, it must be equal to the size in bits, 32 or 64, of the registers in list.
■ For the base address, the SP can be used. In the ARM instruction set, if ! is not specified the
PC can be used.
174
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
■ list must contain at least one register. If it contains doubleword registers, it must not contain
more than 16 registers.
■ If using the Decrement Before addressing mode, the write back flag, !, must be appended
to the base register specification.
8.10.4
Condition flags
These instructions do not change the flags.
November 04, 2011
175
Texas Instruments Incorporated
Floating-Point
8.11
VLDR
Loads a single extension register from memory.
Applies to...
8.11.1
M3
M4
M4F
✓
Syntax
VLDR{cond}{.64} Dd, [Rn{#imm}]
VLDR{cond}{.64} Dd, label
VLDR{cond}{.64} Dd, [PC, #imm}]
VLDR{cond}{.32} Sd, [Rn {, #imm}]
VLDR{cond}{.32} Sd, label
VLDR{cond}{.32} Sd, [PC, #imm]
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
64, 32
are the optional data size specifiers.
Dd
is the destination register for a doubleword load.
Sd
is the destination register for a singleword load.
Rn
is the base register. The SP can be used.
imm
is the + or - immediate offset used to form the address. Permitted address values are multiples
of 4 in the range 0 to 1020.
label
is the label of the literal data item to be loaded.
8.11.2
Operation
This instruction:
176
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
■ Loads a single extension register from memory, using a base address from an ARM core register,
with an optional offset.
8.11.3
Restrictions
There are no restrictions.
8.11.4
Condition flags
These instructions do not change the flags.
November 04, 2011
177
Texas Instruments Incorporated
Floating-Point
8.12
VLMA, VLMS
Multiplies two floating-point values, and accumulates or subtracts the results.
Applies to...
8.12.1
M3
M4
M4F
✓
Syntax
VLMA{cond}.F32 Sd, Sn, Sm
VLMS{cond}.F32 Sd, Sn, Sm
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
Sd
is the destination floating-point value.
Sn, Sm
are the operand floating-point values.
8.12.2
Operation
The floating-point Multiply Accumulate instruction:
1. Multiplies two floating-point values.
2. Adds the results to the destination floating-point value.
The floating-point Multiply Subtract instruction:
1. Multiplies two floating-point values.
2. Subtracts the products from the destination floating-point value.
3. Places the results in the destination register.
8.12.3
Restrictions
There are no restrictions.
8.12.4
Condition flags
These instructions do not change the flags.
178
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
8.13
VMOV Immediate
Move floating-point Immediate.
Applies to...
8.13.1
M3
M4
M4F
✓
Syntax
VMOV{cond}.F32 Sd, #imm
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
Sd
is the branch destination.
imm
is a floating-point constant.
8.13.2
Operation
This instruction copies a constant value to a floating-point register.
8.13.3
Restrictions
There are no restrictions.
8.13.4
Condition flags
These instructions do not change the flags.
November 04, 2011
179
Texas Instruments Incorporated
Floating-Point
8.14
VMOV Register
Copies the contents of one register to another.
Applies to...
8.14.1
M3
M4
M4F
✓
Syntax
VMOV{cond}.F64 Dd, Dm
VMOV{cond}.F32 Sd, Sm
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
Dd
is the destination register, for a doubleword operation.
Dm
is the source register, for a doubleword operation.
Sd
is the destination register, for a singleword operation.
Sm
is the source register, for a singleword operation.
8.14.2
Operation
This instruction copies the contents of one floating-point register to another.
8.14.3
Restrictions
There are no restrictions
8.14.4
Condition flags
These instructions do not change the flags.
180
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
8.15
VMOV Scalar to ARM Core register
Transfers one word of a doubleword floating-point register to an ARM core register.
Applies to...
8.15.1
M3
M4
M4F
✓
Syntax
VMOV{cond} Rt, Dn[x]
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
Rt
is the destination ARM core register.
Dn
is the 64-bit doubleword register.
x
Specifies which half of the doubleword register to use:
■ If x is 0, use lower half of doubleword register
■ If x is 1, use upper half of doubleword register.
8.15.2
Operation
This instruction transfers:
■ one word from the upper or lower half of a doubleword floating-point register to an ARM core
register.
8.15.3
Restrictions
Rt cannot be PC or SP.
8.15.4
Condition flags
These instructions do not change the flags.
November 04, 2011
181
Texas Instruments Incorporated
Floating-Point
8.16
VMOV ARM Core register to single precision
Transfers a single-precision register to and from an ARM core register.
Applies to...
8.16.1
M3
M4
M4F
✓
Syntax
VMOV{cond} Sn, Rt
VMOV{cond} Rt, Sn
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
Sn
is the single-precision floating-point register.
Rt
is the ARM core register.
8.16.2
Operation
This instruction transfers:
■ The contents of a single-precision register to an ARM core register.
■ The contents of an ARM core register to a single-precision register.
8.16.3
Restrictions
Rt cannot be PC or SP.
8.16.4
Condition flags
These instructions do not change the flags.
182
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
8.17
VMOV Two ARM Core registers to two single precision
Transfers two consecutively numbered single-precision registers to and from two ARM core registers.
Applies to...
8.17.1
M3
M4
M4F
✓
Syntax
VMOV{cond} Sm, Sm1, Rt, Rt2
VMOV{cond} Rt, Rt2, Sm, Sm
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
Sm
is the first single-precision register.
Sm1
is the second single-precision register. This is the next single-precision register after Sm.
Rt
is the ARM core register that Sm is transferred to or from.
Rt2
is the The ARM core register that Sm1 is transferred to or from.
8.17.2
Operation
This instruction transfers:
■ The contents of two consecutively numbered single-precision registers to two ARM core registers.
■ The contents of two ARM core registers to a pair of single-precision registers.
8.17.3
Restrictions
The restrictions are:
■ The floating-point registers must be contiguous, one after the other.
■ The ARM core registers do not have to be contiguous.
■ Rt cannot be PC or SP.
8.17.4
Condition flags
These instructions do not change the flags.
November 04, 2011
183
Texas Instruments Incorporated
Floating-Point
8.18
VMOV ARM Core register to scalar
Transfers one word to a floating-point register from an ARM core register.
Applies to...
8.18.1
M3
M4
M4F
✓
Syntax
VMOV{cond}{.32} Dd[x], Rt
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
32
is an optional data size specifier.
Dd[x]
is the destination, where [x] defines which half of the doubleword is transferred, as follows:
■ If x is 0, the lower half is extracted
■ If x is 1, the upper half is extracted.
Rt
is the source ARM core register.
8.18.2
Operation
This instruction transfers one word to the upper or lower half of a doubleword floating-point register
from an ARM core register.
8.18.3
Restrictions
Rt cannot be PC or SP.
8.18.4
Condition flags
These instructions do not change the flags.
184
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
8.19
VMRS
Move to ARM Core register from floating-point System Register.
Applies to...
8.19.1
M3
M4
M4F
✓
Syntax
VMRS{cond} Rt, FPSCR
VMRS{cond} APSR_nzcv, FPSCR
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
Rt
is the destination ARM core register. This register can be R0-R14.
APSR_nzcv
Transfer floating-point flags to the APSR flags.
8.19.2
Operation
This instruction performs one of the following actions:
■ Copies the value of the FPSCR to a general-purpose register.
■ Copies the value of the FPSCR flag bits to the APSR N, Z, C, and V flags.
8.19.3
Restrictions
Rt cannot be PC or SP.
8.19.4
Condition flags
These instructions optionally change the flags: N, Z, C, V
November 04, 2011
185
Texas Instruments Incorporated
Floating-Point
8.20
VMSR
Move to floating-point System Register from ARM Core register.
Applies to...
8.20.1
M3
M4
M4F
✓
Syntax
VMSR{cond} FPSCR, Rt
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
Rt
is the general-purpose register to be transferred to the FPSCR.
8.20.2
Operation
This instruction moves the value of a general-purpose register to the FPSCR. See the Floating Point
Status Control Register for more information.
8.20.3
Restrictions
The restrictions are:
■ Rt cannot be PC or SP.
8.20.4
Condition flags
This instruction updates the FPSCR.
186
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
8.21
VMUL
Floating-point Multiply.
Applies to...
8.21.1
M3
M4
M4F
✓
Syntax
VMUL{cond}.F32 {Sd,} Sn, Sm
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
Sd
is the destination floating-point value.
Sn, Sm
are the operand floating-point values.
8.21.2
Operation
This instruction:
1. Multiplies two floating-point values.
2. Places the results in the destination register.
8.21.3
Restrictions
There are no restrictions.
8.21.4
Condition flags
These instructions do not change the flags.
November 04, 2011
187
Texas Instruments Incorporated
Floating-Point
8.22
VNEG
Floating-point Negate.
Applies to...
8.22.1
M3
M4
M4F
✓
Syntax
VNEG{cond}.F32 Sd, Sm
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
Sd
is the destination floating-point value.
Sm
is the operand floating-point value.
8.22.2
Operation
This instruction:
1. Negates a floating-point value.
2. Places the results in a second floating-point register.
The floating-point instruction inverts the sign bit.
8.22.3
Restrictions
There are no restrictions.
8.22.4
Condition flags
These instructions do not change the flags.
188
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
8.23
VNMLA, VNMLS, VNMUL
Floating-point multiply with negation followed by add or subtract.
Applies to...
8.23.1
M3
M4
M4F
✓
Syntax
VNMLA{cond}.F32 Sd, Sn, Sm
VNMLS{cond}.F32 Sd, Sn, Sm
VNMUL{cond}.F32 {Sd,} Sn, Sm
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
Sd
is the destination floating-point register.
Sn, Sm
are the operand floating-point registers.
8.23.2
Operation
The VNMLA instruction:
1. Multiplies two floating-point register values.
2. Adds the negation of the floating-point value in the destination register to the negation of the
product.
3. Writes the result back to the destination register.
The VNMLS instruction:
1. Multiplies two floating-point register values.
2. Adds the negation of the floating-point value in the destination register to the product.
3. writes the result back to the destination register.
The VNMUL instruction:
1. Multiplies together two floating-point register values.
2. Writes the negation of the result to the destination register.
November 04, 2011
189
Texas Instruments Incorporated
Floating-Point
8.23.3
Restrictions
There are no restrictions.
8.23.4
Condition flags
These instructions do not change the flags.
190
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
8.24
VPOP
Floating-point extension register Pop.
Applies to...
8.24.1
M3
M4
M4F
✓
Syntax
VPOP{cond}{.size} list
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
size
is an optional data size specifier. If present, it must be equal to the size in bits, 32 or 64, of the
registers in list.
list
is a list of extension registers to be loaded, as a list of consecutively numbered doubleword or
singleword registers, separated by commas and
surrounded by brackets.
8.24.2
Operation
This instruction loads multiple consecutive extension registers from the stack.
8.24.3
Restrictions
The list must contain at least one register, and not more than sixteen registers.
8.24.4
Condition flags
These instructions do not change the flags.
November 04, 2011
191
Texas Instruments Incorporated
Floating-Point
8.25
VPUSH
Floating-point extension register Push.
Applies to...
8.25.1
M3
M4
M4F
✓
Syntax
VPUSH{cond}{.size} list
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
size
is an optional data size specifier. If present, it must be equal to the size in bits, 32 or 64, of the
registers in list.
list
is a list of the extension registers to be stored, as a list of consecutively numbered doubleword
or singleword registers, separated by commas and surrounded by brackets.
8.25.2
Operation
This instruction:
■ Stores multiple consecutive extension registers to the stack.
8.25.3
Restrictions
The restrictions are:
■ list must contain at least one register, and not more than sixteen.
8.25.4
Condition flags
These instructions do not change the flags.
192
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
8.26
VSQRT
Floating-point Square Root.
Applies to...
8.26.1
M3
M4
M4F
✓
Syntax
VSQRT{cond}.F32 Sd, Sm
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
Sd
is the destination floating-point value.
Sm
is the operand floating-point value.
8.26.2
Operation
This instruction:
■ Calculates the square root of the value in a floating-point register.
■ Writes the result to another floating-point register.
8.26.3
Restrictions
There are no restrictions.
8.26.4
Condition flags
These instructions do not change the flags.
November 04, 2011
193
Texas Instruments Incorporated
Floating-Point
8.27
VSTM
Floating-point Store Multiple.
Applies to...
8.27.1
M3
M4
M4F
✓
Syntax
VSTM{mode}{cond}{.size} Rn{!}, list
where:
mode
is the addressing mode:
■ IA Increment After. The consecutive addresses start at the address specified in Rn. This is
the default and can be omitted.
■ DB Decrement Before. The consecutive addresses end just before the address specified in
Rn.
cond
is an optional condition code, see “Conditional Execution” on page 32.
size
is an optional data size specifier. If present, it must be equal to the size in bits, 32 or 64, of
theregisters in list.
Rn
is the base register. The SP can be used.
!
is the function that causes the instruction to write a modified value back to Rn. Required if mode
== DB.
list
is a list of the extension registers to be stored, as a list of consecutively numbered doubleword
or singleword registers, separated by commas and surrounded by brackets.
8.27.2
Operation
This instruction:
■ Stores multiple extension registers to consecutive memory locations using a base address from
an ARM core register.
8.27.3
Restrictions
The restrictions are:
■ list must contain at least one register. If it contains doubleword registers it must not contain
more than 16 registers.
194
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
■ Use of the PC as Rn is deprecated.
8.27.4
Condition flags
These instructions do not change the flags.
November 04, 2011
195
Texas Instruments Incorporated
Floating-Point
8.28
VSTR
Floating-point Store.
Applies to...
8.28.1
M3
M4
M4F
✓
Syntax
VSTR{cond}{.32} Sd, [Rn{, #imm}]
VSTR{cond}{.64} Dd, [Rn{, #imm}]
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
32, 64
are the optional data size specifiers.
Sd
is the source register for a singleword store.
Dd
is the source register for a doubleword store.
Rn
is the base register. The SP can be used.
imm
is the + or - immediate offset used to form the address. Values are multiples of 4 in the range
0-1020. imm can be omitted, meaning an offset of +0.
8.28.2
Operation
This instruction:
■ Stores a single extension register to memory, using an address from an ARM core register, with
an optional offset, defined in imm.
8.28.3
Restrictions
The restrictions are:
■ The use of PC for Rn is deprecated.
8.28.4
Condition flags
These instructions do not change the flags.
196
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
8.29
VSUB
Floating-point Subtract.
Applies to...
8.29.1
M3
M4
M4F
✓
Syntax
VSUB{cond}.F32 {Sd,} Sn, Sm
where:
cond
is an optional condition code, see “Conditional Execution” on page 32.
Sd
is the destination floating-point value.
Sn, Sm
are the operand floating-point value.
8.29.2
Operation
This instruction:
1. Subtracts one floating-point value from another floating-point value.
2. Places the results in the destination floating-point register.
8.29.3
Restrictions
There are no restrictions.
8.29.4
Condition flags
These instructions do not change the flags.
8.29.5
Operation
WFI is a hint instruction that suspends execution until one of the following events occurs:
■ a non-masked interrupt occurs and is taken
■ an interrupt masked by PRIMASK becomes pending
■ a Debug Entry request.
8.29.6
Condition flags
This instruction does not change the flags.
November 04, 2011
197
Texas Instruments Incorporated
Floating-Point
8.29.7
Examples
WFI ; Wait for interrupt
198
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
9
Branch and Control Instructions
Table 9-1 on page 199 shows the branch and control instructions:
Table 9-1. Branch and Control Instructions
Mnemonic
Brief Description
B
Branch
200
BL
Branch with link
200
BLX
Branch indirect with link
200
BX
Branch indirect
200
CBNZ
Compare and branch if non-zero
202
CBZ
Compare and branch if zero
202
IT
If-Then
203
TBB
Table branch byte
206
TBH
Table branch halfword
206
November 04, 2011
See Page
199
Texas Instruments Incorporated
Branch and Control Instructions
9.1
B, BL, BX, and BLX
Branch instructions.
Applies to...
9.1.1
M3
M4
M4F
✓
✓
✓
Syntax
B{cond} label
BL{cond} label
BX{cond} Rm
BLX{cond} Rm
where:
B
Is branch (immediate).
BL
Is branch with link (immediate).
BX
Is branch indirect (register).
BLX
Is branch indirect with link (register).
cond
Is an optional condition code. See Table 1-2 on page 33.
label
Is a PC-relative expression. See “PC-Relative Expressions” on page 32.
Rm
Is a register that indicates an address to branch to. Bit[0] of the value in Rm must be 1, but the
address to branch to is created by changing bit[0] to 0.
9.1.2
Operation
All these instructions cause a branch to label, or to the address indicated in Rm. In addition:
■ The BL and BLX instructions write the address of the next instruction to the Link Register (LR),
register R14. See the Stellaris® Data Sheet for more on LR.
■ The BX and BLX instructions cause a UsageFault exception if bit[0] of Rm is 0.
B cond label is the only conditional instruction that can be either inside or outside an IT block. All
other branch instructions must be conditional inside an IT block, and must be unconditional outside
the IT block. See 203.
Table 9-2 on page 201 shows the ranges for the various branch instructions.
200
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
Table 9-2. Branch Ranges
a
Instruction
Branch Range
B label
−16 MB to +16 MB
Bcond label (outside IT block)
−1 MB to +1 MB
Bcond label (inside IT block)
−16 MB to +16 MB
BL{cond} label
−16 MB to +16 MB
BX{cond} Rm
Any value in register
BLX{cond} Rm
Any value in register
a. You might have to use the .W suffix to get the maximum branch range. See “Instruction Width Selection” on page 34.
9.1.3
Restrictions
The restrictions are:
■ Do not use PC in the BLX instruction.
■ For BX and BLX, bit[0] of Rm must be 1 for correct execution but a branch occurs to the target
address created by changing bit[0] to 0.
■ When any of these instructions is inside an IT block, it must be the last instruction of the IT
block.
Note:
9.1.4
B cond is the only conditional instruction that is not required to be inside an IT block.
However, it has a longer branch range when it is inside an IT block.
Condition Flags
These instructions do not change the flags.
9.1.5
Examples
B
BLE
B.W
BEQ
BEQ.W
BL
loopA
ng
target
target
target
funC
BX
BXNE
BLX
LR
R0
R0
;
;
;
;
;
;
;
;
;
;
;
Branch to loopA.
Conditionally branch to label ng.
Branch to target within 16MB range.
Conditionally branch to target.
Conditionally branch to target within 1MB.
Branch with link (Call) to function funC, return address
stored in LR.
Return from function call.
Conditionally branch to address stored in R0.
Branch with link and exchange (Call) to a address stored
in R0.
November 04, 2011
201
Texas Instruments Incorporated
Branch and Control Instructions
9.2
CBZ and CBNZ
Compare and Branch if Zero, Compare and Branch if Non-Zero.
Applies to...
9.2.1
M3
M4
M4F
✓
✓
✓
Syntax
CBZ Rn, label
CBNZ Rn, label
where:
Rn
Is the register holding the operand.
label
Is the branch destination.
9.2.2
Operation
Use the CBZ or CBNZ instructions to avoid changing the condition code flags and to reduce the
number of instructions.
CBZ Rn, label does not change condition flags but is otherwise equivalent to:
CMP
BEQ
Rn, #0
label
CBNZ Rn, label does not change condition flags but is otherwise equivalent to:
CMP
BNE
9.2.3
Rn, #0
label
Restrictions
The restrictions are:
■ Rn must be in the range of R0 to R7.
■ The branch destination must be within 4 to 130 bytes after the instruction.
■ These instructions must not be used inside an IT block.
9.2.4
Condition Flags
These instructions do not change the flags.
9.2.5
Examples
CBZ
CBNZ
R5, target ; Forward branch if R5 is zero.
R0, target ; Forward branch if R0 is not zero.
202
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
9.3
IT
If-Then.
Applies to...
9.3.1
M3
M4
M4F
✓
✓
✓
Syntax
IT{x{y{z}}} cond
where:
x
Specifies the condition switch for the second instruction in the IT block.
y
Specifies the condition switch for the third instruction in the IT block.
z
Specifies the condition switch for the fourth instruction in the IT block.
cond
Specifies the condition for the first instruction in the IT block.
The condition switch for the second, third and fourth instruction in the IT block can be either:
T
Then. Applies the condition cond to the instruction.
E
Else. Applies the inverse condition of cond to the instruction.
Note:
9.3.2
It is possible to use AL (the always condition) for cond in an IT instruction. If this is done,
all of the instructions in the IT block must be unconditional, and each of x, y, and z must
be T or omitted but not E.
Operation
The IT instruction makes up to four following instructions conditional. The conditions can be all the
same, or some of them can be the logical inverse of the others. The conditional instructions following
the IT instruction form the IT block.
The instructions in the IT block, including any branches, must specify the condition in the {cond}
part of their syntax.
Note:
Your assembler might be able to generate the required IT instructions for conditional
instructions automatically, so that you do not need to write them yourself. See your assembler
documentation for details.
A BKPT instruction in an IT block is always executed, even if its condition fails.
Exceptions can be taken between an IT instruction and the corresponding IT block, or within an
IT block. Such an exception results in entry to the appropriate exception handler, with suitable
return information in LR and stacked PSR. See the PSR register in the Stellaris® Data Sheet for
more information.
November 04, 2011
203
Texas Instruments Incorporated
Branch and Control Instructions
Instructions designed for use for exception returns can be used as normal to return from the exception,
and execution of the IT block resumes correctly. This is the only way that a PC-modifying instruction
is permitted to branch to an instruction in an IT block.
9.3.3
Restrictions
The following instructions are not permitted in an IT block:
■ IT
■ CBZ and CBNZ
■ CPSID and CPSIE
Other restrictions when using an IT block are:
■ A branch or any instruction that modifies the PC must either be outside an IT block or must be
the last instruction inside the IT block. These are:
– ADD PC, PC, Rm
– MOV PC, Rm
– B, BL, BX, BLX
– any LDM, LDR, or POP instruction that writes to the PC
– TBB and TBH
■ Do not branch to any instruction inside an IT block, except when returning from an exception
handler.
■ All conditional instructions except Bcond must be inside an IT block. Bcond can be either outside
or inside an IT block but has a larger branch range if it is inside one.
■ Each instruction inside the IT block must specify a condition code suffix that is either the same
or the logical inverse.
Note:
9.3.4
Your assembler might place extra restrictions on the use of IT blocks, such as prohibiting
the use of assembler directives within them.
Condition Flags
This instruction does not change the flags.
9.3.5
Example
ITTE
ANDNE
ADDSNE
MOVEQ
NE
R0, R0, R1
R2, R2, #1
R2, R3
;
;
;
;
Next 3 instructions are conditional.
ANDNE does not update condition flags.
ADDSNE updates condition flags.
Conditional move.
CMP
R0, #9
ITE
ADDGT
ADDLE
GT
R1, R0, #55
R1, R0, #48
;
;
;
;
;
Convert R0 hex value (0 to 15) into ASCII
('0'-'9', 'A'-'F').
Next 2 instructions are conditional.
Convert 0xA -> 'A'.
Convert 0x0 -> '0'.
204
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
IT
ADDGT
GT
R1, R1, #1
; IT block with only one conditional instruction.
; Increment R1 conditionally.
ITTEE
MOVEQ
ADDEQ
ANDNE
BNE.W
EQ
R0, R1
R2, R2, #10
R3, R3, #1
dloop
;
;
;
;
;
;
IT
ADD
NE
R0, R0, R1
; Next instruction is conditional.
; Syntax error: no condition code used in IT block.
Next 4 instructions are conditional.
Conditional move.
Conditional add.
Conditional AND.
Branch instruction can only be used in the last
instruction of an IT block.
November 04, 2011
205
Texas Instruments Incorporated
Branch and Control Instructions
9.4
TBB and TBH
Table Branch Byte and Table Branch Halfword.
Applies to...
9.4.1
M3
M4
M4F
✓
✓
✓
Syntax
TBB [Rn, Rm]
TBH [Rn, Rm, LSL #1]
where:
Rn
Is the register containing the address of the table of branch lengths.
If Rn is the Program Counter (PC) register, R15, then the address of the table is the address
of the byte immediately following the TBB or TBH instruction.
Rm
Is the index register. This contains an index into the table. For halfword tables, LSL #1 doubles
the value in Rm to form the right offset into the table.
9.4.2
Operation
These instructions cause a PC-relative forward branch using a table of single byte offsets for TBB,
or halfword offsets for TBH. Rn provides a pointer to the table, and Rm supplies an index into the
table. For TBB the branch offset is twice the unsigned value of the byte returned from the table. For
TBH, the branch offset is twice the unsigned value of the halfword returned from the table. The
branch occurs to the address at that offset from the address of the byte immediately after the TBB
or TBH instruction.
9.4.3
Restrictions
The restrictions are:
■ Rn must not be SP.
■ Rm must not be SP and must not be PC.
■ When any of these instructions is used inside an IT block, it must be the last instruction of the
IT block.
9.4.4
Condition Flags
These instructions do not change the flags.
9.4.5
Examples
ADR.W R0, BranchTable_Byte
TBB
[R0, R1]
; R1 is the index, R0 is the base address of the
; branch table.
206
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
Case1
; an instruction sequence follows
Case2
; an instruction sequence follows
Case3
; an instruction sequence follows
BranchTable_Byte
DCB
DCB
DCB
0
((Case2-Case1)/2)
((Case3-Case1)/2)
; Case1 offset calculation.
; Case2 offset calculation.
; Case3 offset calculation.
TBH
[PC, R1, LSL #1]
; R1 is the index, PC is used as base of the
; branch table.
BranchTable_H
DCI
DCI
DCI
((CaseA - BranchTable_H)/2)
((CaseB - BranchTable_H)/2)
((CaseC - BranchTable_H)/2)
; CaseA offset calculation.
; CaseB offset calculation.
; CaseC offset calculation.
CaseA
; an instruction sequence follows
CaseB
; an instruction sequence follows
CaseC
; an instruction sequence follows
November 04, 2011
207
Texas Instruments Incorporated
Miscellaneous Instructions
10
Miscellaneous Instructions
Table 10-1 on page 208 shows the remaining Cortex-M3/M4F instructions:
Table 10-1. Miscellaneous Instructions
Mnemonic
Brief Description
BKPT
Breakpoint
209
CPSID
Change processor state, disable interrupts
210
CPSIE
Change processor state, enable interrupts
210
DMB
Data memory barrier
211
DSB
Data synchronization barrier
212
ISB
Instruction synchronization barrier
213
MRS
Move from special register to register
214
MSR
Move from register to special register
215
NOP
No operation
216
SEV
Send event
217
SVC
Supervisor call
218
WFE
Wait for event
219
WFI
Wait for interrupt
220
208
See Page
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
10.1
BKPT
Breakpoint.
Applies to...
10.1.1
M3
M4
M4F
✓
✓
✓
Syntax
BKPT #imm
where:
imm
Is an expression evaluating to an integer in the range 0-255 (8-bit value).
10.1.2
Operation
The BKPT instruction causes the processor to enter Debug state. Debug tools can use this to
investigate system state when the instruction at a particular address is reached.
imm is ignored by the processor. If required, a debugger can use it to store additional information
about the breakpoint.
The BKPT instruction can be placed inside an IT block, but it executes unconditionally, unaffected
by the condition specified by the IT instruction.
10.1.3
Condition Flags
This instruction does not change the flags.
10.1.4
Examples
BKPT 0xAB
; Breakpoint with immediate value set to 0xAB (debugger can
; extract the immediate value by locating it using the PC).
November 04, 2011
209
Texas Instruments Incorporated
Miscellaneous Instructions
10.2
CPS
Change Processor State.
Applies to...
10.2.1
M3
M4
M4F
✓
✓
✓
Syntax
CPSeffect iflags
where:
effect
Is one of:
IE
Clears the special-purpose register.
ID
Sets the special-purpose register.
iflags
Is a sequence of one or more flags:
i
Set or clear the Priority Mask Register (PRIMASK).
f
Set or clear the Fault Mask Register (FAULTMASK).
10.2.2
Operation
CPS changes the PRIMASK and FAULTMASK special register values. See the Stellaris® Data
Sheet for more information about these registers.
10.2.3
Restrictions
The restrictions are:
■ Use CPS only from privileged software; it has no effect if used in unprivileged software.
■ CPS cannot be conditional and so must not be used inside an IT block.
10.2.4
Condition Flags
This instruction does not change the flags.
10.2.5
Examples
CPSID
CPSID
CPSIE
CPSIE
i
f
i
f
;
;
;
;
Disable interrupts and configurable fault handlers (set PRIMASK).
Disable interrupts and all fault handlers (set FAULTMASK).
Enable interrupts and configurable fault handlers (clear PRIMASK).
Enable interrupts and fault handlers (clear FAULTMASK).
210
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
10.3
DMB
Data Memory Barrier.
Applies to...
10.3.1
M3
M4
M4F
✓
✓
✓
Syntax
DMB{cond}
where:
cond
Is an optional condition code. See Table 1-2 on page 33.
10.3.2
Operation
DMB acts as a data memory barrier. It ensures that all explicit memory accesses that appear before
the DMB instruction (in program order) are completed before any explicit memory accesses that
appear after the DMB instruction (in program order). DMB does not affect the ordering or execution
of instructions that do not access memory.
10.3.3
Condition Flags
This instruction does not change the flags.
10.3.4
Examples
DMB
; Data Memory Barrier
November 04, 2011
211
Texas Instruments Incorporated
Miscellaneous Instructions
10.4
DSB
Data Synchronization Barrier.
Applies to...
10.4.1
M3
M4
M4F
✓
✓
✓
Syntax
DSB{cond}
where:
cond
Is an optional condition code. See Table 1-2 on page 33.
10.4.2
Operation
DSB acts as a special data synchronization memory barrier. Instructions that come after DSB (in
program order) do not execute until the DSB instruction completes. The DSB instruction completes
when all explicit memory accesses before it complete.
10.4.3
Condition Flags
This instruction does not change the flags.
10.4.4
Examples
DSB ; Data Synchronization Barrier
212
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
10.5
ISB
Instruction Synchronization Barrier.
Applies to...
10.5.1
M3
M4
M4F
✓
✓
✓
Syntax
ISB{cond}
where:
cond
Is an optional condition code. See Table 1-2 on page 33.
10.5.2
Operation
ISB acts as an instruction synchronization barrier. It flushes the pipeline of the processor, so that
all instructions following the ISB are fetched from cache or memory again, after the ISB instruction
has been completed.
10.5.3
Condition Flags
This instruction does not change the flags.
10.5.4
Examples
ISB
; Instruction Synchronization Barrier
November 04, 2011
213
Texas Instruments Incorporated
Miscellaneous Instructions
10.6
MRS
Move the contents of a special register to a general-purpose register.
Applies to...
10.6.1
M3
M4
M4F
✓
✓
✓
Syntax
MRS{cond} Rd, spec_reg
where:
cond
Is an optional condition code. See Table 1-2 on page 33.
Rd
Is the destination register.
spec_reg
Can be any of the following special registers: APSR, IPSR, EPSR, IEPSR, IAPSR, EAPSR,
PSR, MSP, PSP, PRIMASK, BASEPRI, BASEPRI_MAX, FAULTMASK, or CONTROL.
10.6.2
Operation
Use MRS in combination with MSR as part of a read-modify-write sequence for updating a PSR, for
example to clear the Q flag.
In process swap code, the programmers model state of the process being swapped out must be
saved, including relevant PSR contents. Similarly, the state of the process being swapped in must
also be restored. These operations use MRS in the state-saving instruction sequence and MSR in
the state-restoring instruction sequence.
Note:
BASEPRI_MAX is an alias of BASEPRI when used with the MRS instruction.
See also “MSR” on page 215.
10.6.3
Restrictions
Rd must not be SP and must not be PC.
10.6.4
Condition Flags
This instruction does not change the flags.
10.6.5
Examples
MRS
R0, PRIMASK ; Read PRIMASK value and write it to R0.
214
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
10.7
MSR
Move the contents of a general-purpose register to a special register.
Applies to...
10.7.1
M3
M4
M4F
✓
✓
✓
Syntax
MSR{cond} spec_reg, Rn
where:
cond
Is an optional condition code. See Table 1-2 on page 33.
Rn
Is the source register.
spec_reg
Can be any of: APSR, IPSR, EPSR, IEPSR, IAPSR, EAPSR, PSR, MSP, PSP, PRIMASK, BASEPRI,
BASEPRI_MAX, FAULTMASK, or CONTROL.
10.7.2
Operation
The register access operation in MSR depends on the privilege level. Unprivileged software can only
access the Application Program Status Register (APSR) (see APSR in the Stellaris® Data Sheet).
Privileged software can access all special registers.
In unprivileged software writes to unallocated or execution state bits in the PSR are ignored.
Note:
When you write to BASEPRI_MAX, the instruction writes to BASEPRI only if either:
■ Rn is non-zero and the current BASEPRI value is 0.
■ Rn is non-zero and less than the current BASEPRI value.
See also “MRS” on page 214.
10.7.3
Restrictions
Rn must not be SP and must not be PC.
10.7.4
Condition Flags
This instruction updates the flags explicitly based on the value in Rn.
10.7.5
Examples
MSR
CONTROL, R1 ; Read R1 value and write it to the CONTROL register.
November 04, 2011
215
Texas Instruments Incorporated
Miscellaneous Instructions
10.8
NOP
No Operation.
Applies to...
10.8.1
M3
M4
M4F
✓
✓
✓
Syntax
NOP{cond}
where:
cond
Is an optional condition code. See Table 1-2 on page 33.
10.8.2
Operation
NOP does nothing. NOP is not necessarily a time-consuming NOP. The processor might remove it
from the pipeline before it reaches the execution stage.
Use NOP for padding, for example to place the following instruction on a 64-bit boundary.
10.8.3
Condition Flags
This instruction does not change the flags.
10.8.4
Examples
NOP
; No Operation
216
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
10.9
SEV
Send Event.
Applies to...
10.9.1
M3
M4
M4F
✓
✓
✓
Syntax
SEV{cond}
where:
cond
Is an optional condition code. See Table 1-2 on page 33.
10.9.2
Operation
SEV is a hint instruction that causes an event to be signaled to all processors within a multiprocessor
system. It also sets the one-bit event register to 1. See "Power Management" in the Stellaris® Data
Sheet.
10.9.3
Condition Flags
This instruction does not change the flags.
10.9.4
Examples
SEV ; Send Event
November 04, 2011
217
Texas Instruments Incorporated
Miscellaneous Instructions
10.10
SVC
Supervisor Call.
Applies to...
10.10.1
M3
M4
M4F
✓
✓
✓
Syntax
SVC{cond} #imm
where:
cond
Is an optional condition code. See Table 1-2 on page 33.
imm
Is an expression evaluating to an integer in the range 0-255 (8-bit value).
10.10.2
Operation
The SVC instruction causes the SVC exception.
imm is ignored by the processor. If required, it can be retrieved by the exception handler to determine
what service is being requested.
10.10.3
Condition Flags
This instruction does not change the flags.
10.10.4
Examples
SVC
0x32
; Supervisor Call (SVC handler can extract the immediate value
; by locating it via the stacked PC).
218
November 04, 2011
Texas Instruments Incorporated
Cortex-M3/M4F Instruction Set
10.11
WFE
Wait For Event.
Applies to...
10.11.1
M3
M4
M4F
✓
✓
✓
Syntax
WFE{cond}
where:
cond
Is an optional condition code. See Table 1-2 on page 33.
10.11.2
Operation
WFE is a hint instruction.
If the one-bit event register is 0, WFE suspends execution until one of the following events occurs:
■ An exception, unless masked by the exception mask registers (PRIMASK, FAULTMASK, and
BASEPRI) or the current priority level.
■ An exception enters the Pending state, if SEVONPEND in the System Control Register (SCR)
is set.
■ A Debug Entry request, if Debug is enabled.
■ An event signaled by a peripheral or another processor in a multiprocessor system using the
SEV instruction.
If the event register is 1, WFE clears it to 0 and returns immediately.
For more information, see "Power Management" in the Stellaris® Data Sheet.
10.11.3
Condition Flags
This instruction does not change the flags.
10.11.4
Examples
WFE
; Wait for Event
November 04, 2011
219
Texas Instruments Incorporated
Miscellaneous Instructions
10.12
WFI
Wait for Interrupt.
Applies to...
10.12.1
M3
M4
M4F
✓
✓
✓
Syntax
WFI{cond}
where:
cond
Is an optional condition code. See Table 1-2 on page 33.
10.12.2
Operation
WFI is a hint instruction that suspends execution until one of the following events occurs:
■ An exception.
■ A Debug Entry request, regardless of whether Debug is enabled.
10.12.3
Condition Flags
This instruction does not change the flags.
10.12.4
Examples
WFI ; Wait for Interrupt
220
November 04, 2011
Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and Automotive www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
www.ti.com/video
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated