SRBE Encoder and Push Operation Type Switch A compact multifunctional operating device that can be utilized on the side of the set device ■ Typical Specifications Items Specifications Ratings(max.)/(min.) (Resistive load) Output voltage 1mA 5V DC/50μA 3V DC Jog portion Push portion 1V max. at 1mA 5V DC (Resistive load) Operating force(Push portion) 3.5±1.5N Travel(Push operation) Operating life 0.2mm Jog portion Push portion 100,000 cycles Product Line SRBE110301 Number of detent Number of pulse Operating direction 12 6 Horizontal Mounting method Rotational torque (Jog portion) Standard SRBE210200 Minimum order unit(pcs.) Japan Export Drawing No. 1,500 6,000 1 1,300 5,200 2 3±2mN・m Low-profile Unit:mm Product No. Number of packages(pcs.) Tape width Export package (mm) measurements(mm) 1 reel 1 case / Japan 1 case / export packing SRBE110301 1,500 3,000 6,000 SRBE210200 1,300 2,600 5,200 428×413×172 Switch Type 24 Reel size Variable Resistor Type Packing Specifications Taping Multi Control Devices Product No. Refer to P.461 for soldering conditions. 455 SRBE Encoder and Push Operation Type Switch Dimensions Unit:mm No. PC board mounting hole dimensions (Viewed from direction A) Style ① ⑥ ⑤ 1 ④ ③ ② Multi Control Devices Variable Resistor Type ④ ① Switch Type 2 ③ ② Output Signal(Encoder) Circuit Diagram ① ② ② ④ 456 ② ③ Multi Control Devices List of Varieties Switch type Type SLLB5 SRBE SLLB Small type W ー 11.8 9.5 D ー 8.7 5.5 H ー 3 2.2 Series Photo Dimensions (typical value) (mm) Number of operating shafts Single-shaft Shaft material Resin Multi Control Devices Directional resolution ー 2-direction Directional operating feeling (tactile feeling) With Without Lever return mechanism Without With Center-push switch With Encoder With Operating temperature range Variable Resistor Type Operating life Operating life without load Operating life with load (at max. rated load) Automotive use With/Without With Without −10℃ to +60℃ −40℃ to +85℃ −10℃ to +60℃ 100,000 cycles 100,000 cycles 100,000 cycles ー 100,000 cycles 100,000 cycles ー ー ー Life cycle (availability) Rating(max.)(Resistive load) Switch Type Output voltage Electrical performance Mechanical performance 1V max. at 1mA 5V DC (Resistive load) 10mA 5V DC 1V max. at Measuring 1mA 5V DC circuit (Resistive load) + 5V 5K ー Measuring terminal Encoder resolution 6 pluses/360° ー Insulation resistance 10MΩ min. 50V DC 100MΩ min. 100V DC Voltage proof 50V AC for 1min. 100V AC for 1min. Push operating force ー 0.65±0.3N Encoder detent torque 3.5±1.5N 2±1N 2.5±1N Terminal strength 3±2mN・m ー ー Terminal strength ー Actuator strength Push / pull directions Operating direction Cold Environmental performance 1mA 5V DC 3N for 1min. 50N ー −30℃ 96h 10N −40℃ 96h Dry heat 85℃ 96h Damp heat 40℃, 90 to 95%RH 96h Page 455 457 −20℃ 96h 459 Switch Type Multi Control Devices Soldering Conditions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 461 Switch Type Multi Control Devices Cautions・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 462 436 Switch Type / Soldering Conditions Reference for Manual Soldering Series Tip temperature Soldering time No. of solders RKJXT1F, RKJXM, RKJXL, SLLB, SLLB5, SRBE, SKRV, SKRH 350±5℃ 3s max. 1 time RKJXS 350±10℃ 3 −0 s +1 2 time max. Reference for Dip Soldering Preheating Soldering surface temperature Heating time Series Dip soldering No. of solders Soldering temperature Soldering time RKJXT1F, RKJXM 100℃ max. 2 min. max. 260±5℃ 5±1s 2 time max. RKJXL 120℃ max. 70s max. 260℃ max. 6s max. 2 time max. Multi Control Devices Example of Reflow Soldering Condition 300 A B 200 Variable Resistor Type Temperature(℃) Temperature profile C D 100 Switch Type Room temperature Time(s) Pre-heating E max. G max. H max. F max. I max. Series A B C D E F G H I No. of reflows RKJXS 260℃ 230℃ 150℃ 150℃ 2 min. ー 10s 40s 4 min. 1 time SLLB5 250℃ 230℃ 150℃ 150℃ ー 2 min. ー 30s ー 1 time SKRV, SKRH, SLLB, SRBE 260℃ 230℃ 180℃ 150℃ 2 min. ー ー 40s ー 1 time Notes 1.The above temperature shall be measured on the mounting surface of a PC board. There are cases where the PC board’ s temperature greatly differs from that of the switch, depending on the material, size thickness of PC boards and others. The above-stated conditions shall also apply to switch surface temperatures. 2.Soldering conditions differ depending on reflow soldering machines. Prior verification of soldering condition is highly recommended. 461