6-position Horizontal Type SRBM Series1001KB

SRBM
6-position Horizontal Type
■ Typical Specifications
Specifications
Rotary switch
Pulse switch
Items
0.1A 16V DC / 50BA 3V DC
Contact resistance
(Initial / After operating life)
Slide
Rating(max.)(
/ min.)
(Resistive load)
Detector
Pulse switching (20 pulses) model
available in same shape
50mΩ max. / 150mΩ max.
Without load
40±20 mN・m
15±7 mN・m
10,000 cycles
30,000 cycles
Push
Rotational torque
Operating life
With load
10,000 cycles(0.1A 16V DC)
Rotary
Product Line
Changeover
timing
Actuator
configuration
Minimum order unit(pcs.)
Actuator
length(mm)
Japan
Export
18-tooth
serration
2
1,600
SRBM131300
2
18-tooth
serration
30±3°
L=20
150
1,200
SRBM131400
L=15
200
1,600
SRBM140700
Non shorting
4
1
L=20
5
6
20
pulses
SRBM121300
Dual-in-line
Package Type
200
3
1
Drawing
No.
SRBM120700
L=15
Flat
Product No.
1,200
SRBM149501
18-tooth
serration
SRBM150500
Flat
SRBM154002
L=15
200
1,600
SRBM160700
SRBM1L0800
—
1
SRBM140800
Flat
18-tooth
serration
18±3°
150
Power
Number
Changeover
Poles Positions
of wafers
angle
2
SRBM1L1400
Flat
Note
All the axis are die casting shafts.
Packing Specifications
Tray
Product No.
Number of packages(pcs.)
1 case / Japan 1 case /export packing
SRBM120700
SRBM121300
SRBM131300
SRBM140700
SRBM150500
SRBM154002
SRBM160700
SRBM1L0800
SRBM1L1400
200
SRBM131400
SRBM140800
SRBM149501
150
Export package
measurements(mm)
1,600
400×270×290
1,200
Refer to P.147 for shaft configurations.
Refer to P.156 for soldering conditions.
145
SRBM
6-position Horizontal Type
Dimensions
Single-shaft Type
Unit:mm
No.
PC board mounting hole dimensions
(Viewed from direction A)
Style
Slide
Rotary switch
A
12.5 max.
L ± 0.3
10-ø0.9
10
Mounting face
+0.1
0 hole
0.7
5
P=2.5
3
0.6
PC board
mounting face
0
0.8 -0.2
5
0
1-0.2
Rotary
M7G0.75
0.35
6
6.5
5.5
5.8
1
ø6
Push
5
6
5.5
Detector
Dimensions
Terminal
No. 1
2
5
5
Center of shaft
P=2.5
Pulse switch
A
Power
12.9 max.
Mounting face
L ± 0.3
2-ø1.5 +0.1
0 hole
10
0.7
4-ø0.9 +0.1
0 hole
0
0.8 -0.2
6.45
PC board
mounting face
3.95
Terminal
No. 1
0.3
2.5
6.45 3.95
Center of shaft
Rotary Switch Circuit Diagram
(Viewed from Direction A of Below Diagram)
C.C.W.
C.W.
(Counter-clockwise)
(Clockwise)
Front (Front circuit viewed from shaft direction)
Rear (Rear circuit viewed from shaft direction)
21
5
2 to 4-position
A
3
4
5
C.W. : ①② ON during changeover only
C.C.W. : ③④ ON during changeover only
Rear
5
7
6
5.5
2
5
7
Pulse Switch Circuit Diagram
43
0
0.2
2.5
2.5
0.4
1-0.2
3
M7G0.75
0.6
6.5
5.5
5.8
2
ø6
Dual-in-line
Package Type
5
2.5
6
5-position ※ 1
Front
5
1
4321
5 432
Rear
Front
5
4
1
3 2
6-position ※ 2
Rear
5
1
5
4 3
Front
2
4
1
3 2
1
5
4 3
2
Notes
1. For position 2 to 4, 1section consists of 2-pole.
2. For position 5 and 6, 1 section consists of 1-pole.
※ 1: Circuit steps are position 2 to 5 at front and position 1 to 4 at rear.(External wiring to common terminal is required.)
※ 2: Circuit steps are position 3 to 6 at front and position 1 to 4 at rear.(External wiring to common terminal is required.)
146
SRBM/6-position Horizontal Type
Detector
Dummy Terminals
Number of
positions
3
4
5
6
Front
④ ⑤
⑤
—
—
—
Rear
③ ④
④
—
—
—
Slide
2
Push
18-tooth Serration Shaft
The shaft shows the position in which it is turned fully counterclockwise.
8
20
12
ø6.1 Except serrated part
Testing jig
dimensions
0.07
Shaft dimensions
Dual-in-line
Package Type
Flat Shaft
The shaft shows the position in which it is turned fully counterclockwise.
Die Casting Shaft
L ±0.5
Unit:mm
Shaft
length L
±0.5 when R>10
0
ø6 -0.05
0
4.5 -0.05
R±0.3
R
15
7
20
12
Power
C1
15
98˚
90˚
20˚
ø6
ø6.08
ø5.06
ø5.3
ø6
0.7
R
R
Rotary
18 tooth serration
L±0.5
Details About Serration
(1)T
he mold dimensions of standard serration
and the dimensions of test jigs are as shown in the
figure at left.
(2)
Position of the serration bottom
When the shaft is turned fully counterclockwise, the
position of the serration bottom is on the AA line.
(3)
Slitting angle
The slitting angle(position)is not specified.
7
Unit:mm
Shaft
length L
ø6.1
Die Casting Shaft
Shaft flatten angle
C1
ø6.1±0.2 except for flat part
Note
SRBM Series are based on p(printed terminal direction)
.
Attached Parts
Unit:mm
Hexagonal nut
11
Flat washer
2
ø12
0.5
ø7.1
M7G0.75
147
Rotary Switches
List of Varieties
SRBQ
SRBD
Series
Detector
Insertion Reflow type
SRBM
Rotary
Pulse
SRBV
SRRM
SRRN
Photo
Slide
Angle of throw
36°
40±3°
Number of poles
Push
Rotational torque
W
30±3° 18±3°
1
6±3mN・m
13±5mN・m
13±5mN・m
30±3°
1, 2
1
1, 2 ,3, 4
2, 3, 4
40±20mN・m
15±7mN・m
30±15mN・m
80±30mN・m
(Shorting)
70±30mN・m
(Non shorting)
70±30mN・m
—
—
11.4
10
16.2
12.4
12.5
18.5
1.7
3.5
11
7.5
Operating
temperature range
−25℃ to +85℃
−10℃ to +60℃
−30℃ to +85℃
−10℃ to +85℃
−10℃ to +60℃
−30℃ to +65℃
Automotive use
—
—
●
—
—
—
0.3A 16V DC
50μA 3V DC
0.25A 30V DC
50μA 3V DC
0.15A 12V DC
50μA 3V DC
10,000 cycles
100mΩ max.
10,000 cycles
40mΩ max.
10,000 cycles
70mΩ max.
10,000 cycles
60mΩ max.
10,000 cycles
100mΩ max.
20mΩ max.
50mΩ max.
Dimensions
(mm)
D
Rotary
H
10
Power
Life cycle
Dual-in-line
Package Type
Rating (max.)/(min.)
(Resistive load)
Operating life
without load
Durability
Operating life with load
Load: as rating
Initial contact
resistance
Electrical
performance
1mA 5V DC
50μA 3V DC
0.1A 16V DC
50μA 3V DC
10,000 cycles
250mΩ max.
30,000
cycles
100mΩ
max.
10,000 cycles
100mΩ max.
10,000 cycles 250mΩ max.
10,000 cycles
100mΩ max.
200mΩ max.
10,000 cycles
150mΩ max.
50mΩ max.
Insulation
resistance
100MΩ min. 100V DC
100MΩ min. 500V DC
Voltage proof
100V AC for 1minute
500V AC for 1minute
Terminal
strength
Actuator
strength
3N for 1minute
5N for 1minute
Operating
direction
—
—
Pulling
direction
50N
20N
0.5N・m
—
10N for 1minute
0.6N・m
5N for 1minute
1N・m
100N
Load at the tip of shaft SRRM, SRBM, SRRN:5N, SRBQ, SRBV:1N The below table shows for
SRRM, SRBM, SRRN
Mechanical
performance
Wobble of
actuator
Environmental
performance
Measuring
position from
mounting surface
Shaft wobble
(max. value)
Applicable
mounting
dimension
The below table shows for
SRBQ
The below table shows for
SRBV
Distance from
mounting surface to
the tip of shaft
Shaft wobble
(max. value)
Measuring
position from
mounting surface
Shaft wobble
(max. value)
Applicable
mounting
dimension
10
0.17
15
below 5
0.5
10
0.2
15
15
0.25
20
above 5 and below 10
0.9
15
0.3
20
20
0.35
25
above 10 and below 15
1.2
20
0.4
25
25
0.42
30
30
0.5
above 35
Unit:mm
Cold
−40℃ 500h
Dry heat
85℃ 500h
85℃ 96h
Damp heat
60℃,
90 to 95%RH 500h
40℃, 90 to 95%RH 96h
Page
141
−20℃ 96h
143
−40℃ 96h
145
−20℃ 96h
148
−40℃ 96h
150
153
Rotary Switches Soldering Conditions・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 156
Rotary Switches Cautions・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 157
Note
● Indicates applicability to all products in the series.
140
Rotary Switches Soldering Conditions
Detector
Example of Reflow Soldering Condition
1.
2.
3.
Heating method: Double heating method with infrared heater.
Temperature measurement: Thermocouple φ0.1 to 0.2 CA(K)or CC(T)at soldering portion
(copper foil surface)
.
A heat resisting tape should be used for fixed measurement.
Temperature profile
Push
Temperature (˚C )
Slide
300
A max.
B
200
C
100
Rotary
Room
temperature
Time (s)
Pre-heating
D max.
25s max.
E max.
Power
F
Dual-in-line
Package Type
Series(Reflow type)
A(℃)
3s max.
B(℃)
C(℃)
D(s)
E(s)
F(s)
SRBQ
250
200
150±5
80 to 100
—
—
Temperature (˚C )
300
A max.
B
200
D
E
100
Room
temperature
Time (s)
Pre-heating
F max.
C
Series(Reflow type)
A(℃)
3s max.
B(℃)
C(s)
D(℃)
E(℃)
F(s)
SRBD
260
230
40
180
150
120
Notes 1.The condition mentioned above is the temperature on the mounting surface of a PC board. There are cases where the
PC board's temperature greatly differs from that of the switch, depending on the PC board's material, size, thickness, etc.
The above-stated conditions shall also apply to switch surface temperatures.
2. Soldering conditions differ depending on reflow soldering machines. Prior verification of soldering condition is highly recommended.
Reference for Hand Soldering
Series
Soldering temperature
Soldering time
SRBQ, SRBM, SRBV, SRRM, SRRN
350±10℃
3+1/0s
SRBQ(Reflow type)
350±5℃
3s max.
Reference for Dip Soldering
(For PC board terminal types)
Series
SRBM
156
Items
Preheating temperature
Preheating time
100℃ max.
60s max.
Dip soldering
Soldering temperature Duration of immersion
260±5℃
5s max.
SRBV, SRRM, SRRN
—
260±5℃
10±1s
SRBQ
—
260±5℃
5±1s