LevelOne

LevelOne
Installation Guide
FCS-4020
Day & Night
Speed Dome Network Camera
Ver 1.0
Warning Before Installation
Power off the Network Camera as
soon as smoke or unusual odors are
detected.
Refer to your user’s manual for the
operating temperature.
Contact your distributor in the
event of occurrence.
Do not disassemble the Network
Camera.
Do not touch the Network Camera
during a lightning storm.
Do not insert sharp or tiny objects
into the Network Camera.
Do not drop the Network Camera.
Do not manually pan and tilt the
Network Camera when the power is
on.
1
1
Package Contents
FCS-4020
Black Cover / Dome Cover
Wall Mount Bracket
Power Adapter
or
Silica Gel / Metal Ring
O-ring and Screws /
Alignment Sticker
Silica gel
Silica gel
RJ45 Female/Female Coupler
Quick Installation Guide
Warranty Card
Software CD
2
2
Physical Description
Inner View
SD Card Slot
Status LED
Reset Button
Lens
Outer View
General I/O
Terminal Block
Ethernet 10/100
RJ45 Plug
Audio Out (green)
Microphone In (pink)
Power Cord Socket (black)
Ground
3
3
Hardware Installation
Mounting the Network Camera
1. Attach the alignment sticker to the wall.
2. Drill four pilot holes into the wall.
3. Attach the black cover to the Network Camera using the supplied four black
screws.
4. Stick the supplied two pieces of silica gel symmetrically to the inner side of the
dome cover. Then place the metal ring into the dome cover to fix the silica gel.
5. Fix the dome cover to the Network Camera and secure it by rotating it clockwise.
6. Loosen the three screws on the front opening of the wall mount bracket.
7. Place the O-ring on the front opening of the wall mount bracket.
8. Feed the cables through the front opening of the wall mount bracket and pull them
from wall outlet.
9. Attach the Network Camera to the wall mount bracket by tightening the three
screws on the front opening of the wall mount bracket.
10. Fasten the wall mount bracket to the wall.
10
1
7
8
2
3
5
6
4
Silica gel
Silica gel
4
9
4
Network Deployment
1. If you have external devices such as
sensors and alarms, connect them to
the general I/O terminal block.
G
D
D
D
D
ND:
I 4 :
I 3 :
I 2 :
I 1 :
GND:
N.O. :
COM. :
+12V :
Ground
Digital Input
Digital Input
Digital Input
Digital Input
Ground
RELAY_NO
RELAY_COM
Power, 12V DC
2. Use the supplied RJ45 female/female
coupler to connect the Network Camera
to a switch.
Use Category 5 Cross Cable when
Network Camera is directly connected
to PC.
POWER
COLLISION
1
2
3
4
5
LINK
RECEIVE
PARTITION
(AC 24V 2A)
3. Connect the power cable from the
Network Camera to a power outlet.
5
5
Assigning IP Address
1. Install "Installation Wizard " from the Software Utility directory on the software CD.
2. The program will search for LevelOne Network Cameras on the same LAN.
3. After searching, the main installer window will pop up. Click on the MAC that matches
the one labeled on the side of the camera lens or S/N number on the label of carton
to connect the Internet Explorer to the Network Camera.
F CS-4020
H/W Ve r :1 .0
S/N:YYMMDDXXXXX
00-11-6B-80-F1-3E
MAC:00116B80F13E
192.168.3.143
FCS-4020
00116B80F13E
Power : AC24V/2A
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
FCS-4020
H / W Ve r: 1 . 0
S/N:YYMMDDXXXXX
MAC:XXXXXXXXXXXX
N18085
Power : AC24V/2A
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
6
6
Ready to Use
1. Access the Network Camera from the Internet.
2. Retrieve live video through web browsers or recording software.
For further setup, please refer to the user's manual on the software CD.
7