SERIES Single Ear Rotary Position Sensor

500
SERIES
Single Ear Rotary Position Sensor
TYPICAL APPLICATIONS:
Small engine throttle plate position sensing and other similar applications
where available space for an external feedback sensor is limited.
Features/Benefits:
• Compact package with integral Yazaki® connector
Choice of mounting ear locations
Clockwise or counterclockwise rotation
• Highly resistant to fluid intrusion
Internal rotor seal
Optional external interface seal
• Tang drive, spring return rotor accepts 6mm shaft
TYPICAL SPECIFICATIONS:
ELECTRICAL
Total Resistance:
Linearity:
Rotation Maximum:
5.0 k Ω, ± 40%
± 2.0% (point slope linearity)
122º mechanical
105º typical electrical
≤ 1.0% applied voltage
0.8% / degree
6% of applied at mid-adjustment
0 - 20% of applied
5.11 N-cm
16 VDC
5 - 10 VDC
0.8 watts
Hysteresis:
Slope:
Normal Index Voltage:
Adjustable Index Range:
Torque Requirement:
Electrical Limit Maximum:
Typical Voltage:
Maximum Power Rating:
DURABILITY
Mechanical Cycling:
Standard Vibration:
Thermal Shock:
2x106 full strokes @ 1 Hz: 0.5 x 106 half strokes @ 0.5 Hz
24 hrs., 3 planes; random 33 to 2000 Hz; 1.36 - 25g; 0° to 80°C
100 Cycles, -40º to 120ºC; transition time less than 1 minute soak
at each temperature
Temperature Range
2SHUDWLQJžWRž&
-0º to 10ºC
6WRUDJH:
(NVIRONMENTAL
Water Resistance:
Solvent Exposure:
Dust Exposure:
JIS D0203
Brush on gasoline, engine oil brake fluid,
transmission fluid and antifreeze
JIS D0207-F2
NOTE: These standard specifications have been met by existing production-tooled units evaluated with precise test equipment and procedures.
Test results, including failure criteria, is available upon request. This data sheet does not constitute a warranty that the product will meet the above
specifications while used in specific applications or attached to specific test equipment
ctscorp.com
BCW
ACW
125°
Mech. Angle
CCW
125°
Mech. Angle
125°
Mech. Angle
Ø 6.3
105°
Elec. Angle
CW
105°
Elec. Angle
CW
CW
Ø 6.3
Ø 6.3
2.4
105°
Elec. Angle
2.4
2.4
Low End
Stop
Low End
Stop
Low End
Stop
DIMENSION : mm
BCCW
ACCW
125°
Mech. Angle
CCCW
125°
Mech. Angle
105°
Elec. Angle
105°
Elec. Angle
CCW
125°
105°
Mech. Angle
Elec. Angle
CCW
CCW
Ø6.3
2.4
2.4
Low End
Stop
Low End
Stop
Low End
Stop
2.4
Ø 6.3
Ø6.3
DIMENSION : mm
RECOMMENDATION OF CUSTOMER SUPPLIED HARDWARE AND O-RING
Connector
O-Ring
Bolt
Customer
supplied O-ring
5mm bolt
Dia.:10.8±0.15
Dia.:1±0.0.07
Nominal length 16mm - Pitch 0.8mm
Wave Washer 0.5mm approx. thick.
Flat Washer Ø8.9mm min. X 1.0mm thick.
Fastening Torque - 4.5Nm MAX.
Recommendation of connector:
Yazaki Dwg. SSD 3P Connector Male
P/N: 7283-8730-30 : A
2-3
CTS Electrocomponents
© 2014 CTS Corporation. All rights reserved. Information subject to change
09/16/14
Ordering Information
500
A
CCW
D
O
G
MOUNTING STYLE
SPRING
RESISTANCE TOL.
Optional O-ring
Optional Grease
D : ±40 %
O : O-ring installed
A – A TYPE
CW
B – B TYPE
CCW – Counter Clockwise
C – C TYPE
3-3
CTS Electrocomponents
– Clockwise
Blank : No O-ring
© 2014 CTS Corporation. All rights reserved. Information subject to change
G : Grease Inside
Connector Pocket
Blank : No Grease
09/16/14