Application Note AN_199 Vinculum-II SPI Slave to USB HID Class Device Bridge Version 1.0 Issue Date: 2011-12-13 This application note forms part of a series of application notes detailing the new simplified ROM images for Vinculum-II (VNC2). It details the implementation and use of a VNC2 ROM file for bridging a SPI Slave interface to a HID class USB device port. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. Future Technology Devices International Limited (FTDI) Unit 1, 2 Seaward Place, Glasgow G41 1HH, United Kingdom Tel.: +44 (0) 141 429 2777 Fax: + 44 (0) 141 429 2758 Web Site: http://ftdichip.com Copyright © 2011 Future Technology Devices International Limited Application Note AN_199 Vinculum-II SPI Slave to USB HID Class Device Bridge Version 1.0 Document Reference No.: FT_000551 Clearance No.: FTDI# 241 Table of Contents 1 Introduction .................................................................................................................................... 2 1.1 Overview ................................................................................................................................. 2 2 Using the Sample Code ................................................................................................................... 3 3 Default Pin-Out ............................................................................................................................... 4 4 Building and Loading the Firmware into the VNC2......................................................................... 6 5 4.1 Build ........................................................................................................................................ 6 4.2 Load ......................................................................................................................................... 6 4.3 Loading with FT_Prog.............................................................................................................. 7 Source Code for the VNC2 Application ........................................................................................... 8 5.1 6 SPISlave2USBHIDkbd.C ........................................................................................................... 8 5.1.1 main() .............................................................................................................................. 8 5.1.2 Iomux_setup() ................................................................................................................. 8 5.1.3 Open drivers/close drivers .............................................................................................. 8 5.1.4 Attach_drivers() .............................................................................................................. 8 5.1.5 ASCIItoKey ....................................................................................................................... 9 5.1.6 NonAlphaNumeric........................................................................................................... 9 5.1.7 Setup ............................................................................................................................... 9 5.1.8 SPI.................................................................................................................................... 9 Contact Information...................................................................................................................... 10 Appendix A – References ...................................................................................................................... 11 Document References....................................................................................................................... 11 Acronyms and Abbreviations ............................................................................................................ 11 Appendix B – List of Tables & Figures ................................................................................................... 12 List of Tables ..................................................................................................................................... 12 List of Figures .................................................................................................................................... 12 Appendix C – Revision History .............................................................................................................. 13 1 Copyright © 2011 Future Technology Devices International Limited Application Note AN_199 Vinculum-II SPI Slave to USB HID Class Device Bridge Version 1.0 Document Reference No.: FT_000551 Clearance No.: FTDI# 241 1 Introduction FTDI have introduced a new suite of simplified “bridging” ROM files to allow for fast interconnect between differing interfaces. These ROM images (and sample code) are targeted at those users who would like to implement Vinculum-II (VNC2) into a design without creating their own firmware. As well as providing the source code for users wishing to tweak setup parameters the default project will be supplied as a precompiled ROM file ready for installation into the VNC2. This application note forms part of a series of application notes detailing the new simplified ROM images for VNC2. This document will detail the implementation and use of a VNC2 ROM file for bridging a SPI Slave interface to a Human Interface Device (HID) class device on a USB port. This particular project may be used in 32, 48 or 64 pin packages. For users not intending to edit the code in any way the precompiled code may be loaded over the UART interface with FT_PROG as an alternative to using the IDE. Links for the project file SPISlave2USBSlaveHIDKbd.vproj and the precompiled ROM file SPISlave2USBSlaveHIDKbd.rom file may be found at the end of the document in Appendix A. 1.1 Overview Vinculum-II (VNC2) is the second of FTDI’s Vinculum family of embedded dual USB host controller devices. The VNC2 device provides USB Host interfacing capability for a variety of different USB device classes including support for BOMS (bulk only mass storage), Printer and HID (human interface devices). For mass storage devices such as USB Flash drives, VNC2 transparently handles the FAT file structure. Communication with non USB devices, such as a low cost microcontroller, is accomplished via either UART, SPI or parallel FIFO interfaces. VNC2 provides a new, cost effective solution for providing USB Host capability into products that previously did not have the hardware resources available. VNC2 allows customers to develop their own firmware using the Vinculum II software development tool suite. These development tools provide compiler, assembler, linker and debugger tools complete within an integrated development environment (IDE). The Vinculum-II VNC2 family of devices are available in Pb-free (RoHS compliant) 32-lead LQFP, 32-lead QFN, 48-lead LQFP, 48-lead QFN, 64-Lead LQFP and 64-lead QFN packages For more information on the ICs refer to http://www.ftdichip.com/Products/ICs/VNC2.htm. 2 Copyright © 2011 Future Technology Devices International Limited Application Note AN_199 Vinculum-II SPI Slave to USB HID Class Device Bridge Version 1.0 Document Reference No.: FT_000551 Clearance No.: FTDI# 241 2 Using the Sample Code 3V3 VREGOUT 1V8 PLL IN SPI DATA VNC2 XTIN XTOUT DEBUGGER I/F USB USB HOST SUPPORTING HID CLASS DEVICES TEST SPI MASTER DEVICE VCCIO 3V3VREGIN RESET PROG# 1V8 12MHz GND Figure 2.1 Connecting the Demo When the VNC2 is programmed, the user simply passes data from the SPI Master device to the VNC2. The VNC2 will process this data to pass it out to USB port 1 of the chip to the USB host. There are no additional commands required, it is a simple data bridge. The project default set the SPI to mode 0, MSB first, unmanaged mode. 3 Copyright © 2011 Future Technology Devices International Limited Application Note AN_199 Vinculum-II SPI Slave to USB HID Class Device Bridge Version 1.0 Document Reference No.: FT_000551 Clearance No.: FTDI# 241 3 Default Pin-Out The VNC2 can assign the same signal to a variety of pins. The default pins used for this ROM image are shown in Error! Reference source not found.. Signal 32-pin pkg 48-pin pkg 64-pin pkg Description GND 1, 16, 19, 27 1, 24, 27, 39 1, 30, 35, 53 Device ground supply pins 3V3 VREGIN 2 2 2 1V8 VCC PLL IN 3 3 3 GND PLL 6 6 6 VREG OUT 7 7* 7 +3.3VDC supply to the regulator +1.8VDC supply to internal clock multiplier Requires 100nF decoupling capacitor close to pin Device analog ground supply for internal clock multiplier +1.8VDC output from regulator to device core *Not used on 48-pin LQFP package VCCIO 13, 22, 28 17, 30, 40 21, 38, 54 +3.3VDC supply to I/O interface pins (IOBUS) VCCIO must be connected for proper operation Input to 12MHz Oscillator XTIN 4 4 4 Connect 12MHz crystal across pins 4 and 5 with proper loading capacitance Output from 12MHz Oscillator Connect 12MHz crystal across pins 4 and 5 with proper loading capacitance XTOUT 5 5 5 TEST 8 8 8 Test – Must be connected to GND for normal operation RESET# 10 9 9 Can be used by an external device to reset VNC2 PROG# 9 10 10 Asserting PROG# enables program mode DEBUGGER I/F 11 11 11 I/O for programming and in-circuit debugging USB DP1 17 25 33 USB Port 1 Data Plus USB DM1 18 26 34 USB Port 1 Data Minus SPI_S0_CLK 29 15 51 SPI Slave Clock input 4 Copyright © 2011 Future Technology Devices International Limited Application Note AN_199 Vinculum-II SPI Slave to USB HID Class Device Bridge Version 1.0 Document Reference No.: FT_000551 Clearance No.: FTDI# 241 Signal 32-pin pkg 48-pin pkg 64-pin pkg Description SPI_S0_MOSI 30 16 52 SPI MOSI input SPI_S0_MISO 31 18 55 SPI MISO output SPI_S0_SS# 32 19 56 SPI Slave select input Table 3.1 VNC2 Pin-Out Designers wanting to customize the design should refer to the iomux.c file for changing pin-out options. More information on pinout options are available in AN_139 Vinculum II IO MUX Explained. 5 Copyright © 2011 Future Technology Devices International Limited Application Note AN_199 Vinculum-II SPI Slave to USB HID Class Device Bridge Version 1.0 Document Reference No.: FT_000551 Clearance No.: FTDI# 241 4 Building and Loading the Firmware into the VNC2 Everything can be controlled by the Vinculum-II IDE (part of the Vinculum-II Toolchain downloadable from the FTDI website). To access the application simply use the Project -> Open tab to browse to the UART2USBHIDkbd.vproj file for your project. Figure 4.1 Vinculum-II Project Open Button 4.1 Build This step is only necessary if you are not using the precompiled version of the ROM. Otherwise proceed to loading the ROM file. To build the application you simply press the Build button on the IDE ribbon bar under the build tab. Figure 4.2 Vinculum-II IDE Build Button 4.2 Load Loading the code is equally simple. Just click on the “Flash” button on the ribbon bar under the debug tab. The Flash button will automatically pick up the Rom file in your project but for reference the filename is UART2USBHIDkbd.ROM. Figure 4.3 Vinculum-II IDE Flash Button Note the Debugger Interface is listed as V2EVAL Board C. It is important that this box shows a device is connected before attempting to flash a device. 6 Copyright © 2011 Future Technology Devices International Limited Application Note AN_199 Vinculum-II SPI Slave to USB HID Class Device Bridge Version 1.0 Document Reference No.: FT_000551 Clearance No.: FTDI# 241 4.3 Loading with FT_Prog If the precompiled ROM file meets all the requirements of the end design then the IDE and source code are not required. The precompiled UART2USBHIDkbd.ROM file may be loaded into the VNC2 with FT_PROG over the UART interface. FT_Prog is used to program the VNC2 with a ROM file. FT_Prog is available from the FTDI website utilities page (version 1.12 or later supports VNC2). Select the flash ROM tab at the top of the window. Select VNC2 from the pull down tab. Select D2xx or VCP interface (either will work). Select the location where the ROM file resides. Press the program button. Perform a hard reset (power cycle) prior to running the firmware. Figure 4.4 is an example of programming the VNC2 Evaluation board revision 2 with the V2DAP firmware. Figure 4.4 FT_Prog Programming Utility For more information on loading ROM files onto a VNC2 device refer to: http://www.ftdichip.com/Support/Documents/AppNotes/AN_159%20VinculumII%20Firmware%20Flash%20Programming.pdf 7 Copyright © 2011 Future Technology Devices International Limited Application Note AN_199 Vinculum-II SPI Slave to USB HID Class Device Bridge Version 1.0 Document Reference No.: FT_000551 Clearance No.: FTDI# 241 5 Source Code for the VNC2 Application This section is aimed at those wanting to learn about coding VNC2 devices or modify the existing project. All VNC2 application firmware follows a similar format and most of the code can be “written” using the IDE application wizard. The basic steps are: 1. Initialise device drivers 2. Define pin-outs 3. Open ports to be used 4. Configure ports to be used 5. Read/write data 6. Close ports The VNC2 source code for this project can be viewed in appendix A and is available to download with the toolchain. 5.1 SPISlave2USBHIDkbd.C SPISlave2HIDkbd.c is the main firmware file. This file is split into multiple functions. void main(); void iomux_setup(void); void open_drivers(void); void close_drivers(void); void attach_drivers(void); unsigned char ASCIItoKey(unsinged char ascii, unsigned char *key, unsigned char *modifier); unsigned char NonAlphaNumeric(); void setup(void) void spi(void) 5.1.1 main() Main is where the application starts. It defines the VNC2 core clock speed, loads the drivers to be used and creates the threads to be used in the application. At the very end of main is the call vos_start_scheduler(); After this call there can be no further configuration of the device. 5.1.2 Iomux_setup() Iomux_setup actually refers to the other file in the project, UART2HIDkbd_iomux.c and is used to define the VNC2 pin-out. Most functions can be programmed to appear on different pins. The notable exceptions are power, GND and the USB ports. 5.1.3 Open drivers/close drivers The open drivers function call will provide a handle to each hardware block used in the project and this handle can be used by subsequent commands to control the hardware. Close drivers closes the handle at the end of the project. 5.1.4 Attach_drivers() This function is used to attach the HID class driver to the USB slave driver. 8 Copyright © 2011 Future Technology Devices International Limited Application Note AN_199 Vinculum-II SPI Slave to USB HID Class Device Bridge Version 1.0 Document Reference No.: FT_000551 5.1.5 Clearance No.: FTDI# 241 ASCIItoKey This is a function to convert ascii to a function key 5.1.6 NonAlphaNumeric This function will handle non-alpha numeric inputs. 5.1.7 Setup Setup will configure the SPI interface to be Vinculum I compatible mode. 5.1.8 SPI The SPI function will read data on the SPI slave port and write it out the USB port to the USB host. 9 Copyright © 2011 Future Technology Devices International Limited Application Note AN_199 Vinculum-II SPI Slave to USB HID Class Device Bridge Version 1.0 Document Reference No.: FT_000551 Clearance No.: FTDI# 241 6 Contact Information Head Office – Glasgow, UK Branch Office – Hillsboro, Oregon, USA Future Technology Devices International Limited Unit 1, 2 Seaward Place, Centurion Business Park Glasgow G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 Future Technology Devices International Limited (USA) 7235 NW Evergreen Parkway, Suite 600 Hillsboro, OR 97123-5803 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) [email protected] [email protected] [email protected] E-Mail (Sales) E-Mail (Support) E-Mail (General Enquiries) [email protected] [email protected] [email protected] Branch Office – Taipei, Taiwan Branch Office – Shanghai, China Future Technology Devices International Limited (Taiwan) 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan , R.O.C. Tel: +886 (0) 2 8791 3570 Fax: +886 (0) 2 8791 3576 Future Technology Devices International Limited (China) Room 408, 317 Xianxia Road, Shanghai, 200051 China Tel: +86 21 62351596 Fax: +86 21 62351595 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) E-mail (Sales) E-mail (Support) E-mail (General Enquiries) [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] Web Site http://ftdichip.com System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future Technology Devices International Ltd (FTDI) devices incorporated in their systems, meet all applicable safety, regulatory and system-level performance requirements. All application-related information in this document (including application descriptions, suggested FTDI devices and other materials) is provided for reference only. While FTDI has taken care to assure it is accurate, this information is subject to customer confirmation, and FTDI disclaims all liability for system designs and for any applications assistance provided by FTDI. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. This document is subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Neither the whole nor any part of the information contained in, or the product described in this document, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640 10 Copyright © 2011 Future Technology Devices International Limited Application Note AN_199 Vinculum-II SPI Slave to USB HID Class Device Bridge Version 1.0 Document Reference No.: FT_000551 Clearance No.: FTDI# 241 Appendix A – References Document References Application and Technical Notes available at http://www.ftdichip.com/Support/Documents/AppNotes.htm VNC2 Datasheet V2-EVAL datasheet Vinculum II Toolchain AN_139 IO_Mux explained AN_151 Vinculum II User Guide AN_159_Vinculum_II_Firmware_Flash_Programming.pdf Project source code download www.ftdichip.com/Firmware/Precompiled/SPISlave2USBSlaveHIDKbd.zip Project precompiled ROM file download www.ftdichip.com/Firmware/Precompiled/SPISlave2USBSlaveHIDKbd.ROM Acronyms and Abbreviations Terms Description HID Human Interface Device SPI Serial Peripheral Interface USB Universal Serial Bus USB-IF USB Implementers Forum NOTE – put terms in alphabetical order. 11 Copyright © 2011 Future Technology Devices International Limited Application Note AN_199 Vinculum-II SPI Slave to USB HID Class Device Bridge Version 1.0 Document Reference No.: FT_000551 Clearance No.: FTDI# 241 Appendix B – List of Tables & Figures List of Tables Table 3.1 VNC2 Pin-Out ....................................................................................................... 5 List of Figures Figure 2.1 Connecting the Demo ........................................................................................... 3 Figure 4.1 Vinculum-II Project Open Button ........................................................................... 6 Figure 4.2 Vinculum-II IDE Build Button ................................................................................ 6 Figure 4.3 Vinculum-II IDE Flash Button ................................................................................ 6 Figure 4.4 FT_Prog Programming Utility ................................................................................. 7 12 Copyright © 2011 Future Technology Devices International Limited Application Note AN_199 Vinculum-II SPI Slave to USB HID Class Device Bridge Version 1.0 Document Reference No.: FT_000551 Clearance No.: FTDI# 241 Appendix C – Revision History Document Title: AN_199 Vinculum-II SPI Slave to USB HID Class Device Bridge Document Reference No.: FT_000551 Clearance No.: FTDI# 241 Product Page: http://www.ftdichip.com/Products/ICs/VNC2.htm Document Feedback: Send Feedback Revision 1.0 Changes Initial Release Date 2011-12-13 13 Copyright © 2011 Future Technology Devices International Limited