L6986
38 V 2 A synchronous step-down switching regulator with 30 μA
quiescent current
Datasheet - production data
Description
HTSSOP16 (RTH = 40 °C/W)
Features
2 A DC output current
4 V to 38 V operating input voltage
Low consumption mode or low noise mode
30 A IQ at light load (LCM VOUT = 3.3 V)
8 A IQ-SHTDWN
Adjustable fSW (250 kHz - 2 MHz)
Output voltage adjustable from 0.85 V to VIN
Embedded output voltage supervisor
Synchronization
Adjustable soft-start time
Internal current limiting
Overvoltage protection
The L6986 device is a step-down monolithic
switching regulator able to deliver up to 2 A DC.
The output voltage adjustability ranges from
0.85 V to VIN. Thanks to the P-channel MOSFET
high-side power element, the device features
100% duty cycle operation. The wide input
voltage range meets the specification for the 5 V,
12 V and 24 V power supplies. The “Low
Consumption Mode” (LCM) is designed for
applications active during idle mode, so it
maximizes the efficiency at light load with
controlled output voltage ripple. The “Low Noise
Mode” (LNM) makes the switching frequency
constant overload current range, meeting the low
noise application specification. The output voltage
supervisor manages the reset phase for any
digital load (C, FPGA, etc.). The RST open
collector output can also implement output
voltage sequencing during the power-up phase.
The synchronous rectification, designed for high
efficiency at medium - heavy load, and the high
switching frequency capability make the size of
the application compact. Pulse by pulse current
sensing on both power elements implements an
effective constant current protection.
Output voltage sequencing
Peak current mode architecture
RDSON HS = 180 m, RDSON LS = 150 m
Thermal shutdown
Applications
Designed for 12 V and 24 V buses
Programmable logic controllers (PLCs)
Decentralized intelligent nodes
Sensors and low noise applications (LNM)
February 2015
This is information on a product in full production.
DocID025376 Rev 5
1/66
www.st.com
Contents
L6986
Contents
1
Application schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2
Pin settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1
Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.3
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.4
Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.5
ESD protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4
Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.1
Power supply and voltage reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Switchover feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2
Voltages monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.3
Soft-start and inhibit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.3.1
Ratiometric startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.3.2
Output voltage sequencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.4
Error amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.5
Light load operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.6
4.7
4.5.1
Low noise mode (LNM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.5.2
Low consumption mode (LCM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Switchover feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.6.1
LCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.6.2
LNM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Overcurrent protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
OCP and switchover feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2/66
4.8
Overvoltage protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.9
Thermal shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
DocID025376 Rev 5
L6986
5
6
Contents
Closing the loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
5.1
GCO(s) control to output transfer function . . . . . . . . . . . . . . . . . . . . . . . . 33
5.2
Error amplifier compensation network . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
5.3
Voltage divider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
5.4
Total loop gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
5.5
Compensation network design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Application notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
6.1
Output voltage adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
6.2
Switching frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
6.3
MLF pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
6.4
Voltage supervisor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
6.5
Synchronization (LNM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
6.6
Design of the power components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
6.6.1
Input capacitor selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
6.6.2
Inductor selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
6.6.3
Output capacitor selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
7
Application board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
8
Efficiency curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
9
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
10
Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
11
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
DocID025376 Rev 5
3/66
66
Application schematic
1
L6986
Application schematic
Figure 1. Application schematic
9,1
&
9%,$6
3:5*1'
*1'
9
Q)
567
&
9
&
9,1
&
Q)
&
Q)
3*1'
/;
3*1'
0/)
/;
5
9287
/
5
/
&
9&&
66,1+
)%
'(/$<
&203
)6:
6*1' (3
6<1&+
5
&
5
*1'
6LJQDO*1'
S)
3:5*1'
$09
4/66
DocID025376 Rev 5
L6986
Pin settings
2
Pin settings
2.1
Pin connection
Figure 2. Pin connection (top view)
2.2
567
9%,$6
9&&
9,1
66,1+
/;
6<1&+
/;
)6:
3*1'
0/)
3*1'
&203
6*1'
'(/$<
(;326('
3$'72
6*1'
)%
Pin description
Table 1. Pin description
No.
Pin
Description
1
RST
The RST open collector output is driven low when the output voltage is out of regulation. The RST
is released after an adjustable time DELAY once the output voltage is over the active delay
threshold.
2
VCC
Connect a ceramic capacitor (≥ 470 nF) to filter internal voltage reference. This pin supplies the
embedded analog circuitry.
3
SS/INH
An open collector stage can disable the device clamping this pin to GND (INH mode). An internal
current generator (2 A typ.) charges the external capacitor to implement the soft-start.
4
SYNCH
Master / slave synchronization
5
FSW
A pull up resistor (E24 series only) to VCC or pull down to GND selects the switching frequency.
Pinstrapping is active only before the soft-start phase to minimize the IC consumption.
6
MLF
A pull up resistor (E24 series only) to VCC or pull down to GND selects the low noise mode/low
consumption mode and the active RST threshold. Pinstrapping is active only before the soft-start
phase to minimize the IC consumption.
7
COMP
Output of the error amplifier. The designed compensation network is connected at this pin.
8
DELAY
An external capacitor connected at this pin sets the time DELAY to assert the rising edge of the
RST o.c. after the output voltage is over the reset threshold. If this pin is left floating, RST is like
a power good.
9
FB
10
SGND
Signal GND
11
PGND
Power GND
Inverting input of the error amplifier
DocID025376 Rev 5
5/66
66
Pin settings
L6986
Table 1. Pin description (continued)
No.
Pin
12
PGND
13
LX
Switching node
14
LX
Switching node
15
VIN
DC input voltage
16
VBIAS
Typically connected to the regulated output voltage. An external voltage reference can be used to
supply part of the analog circuitry to increase the efficiency at light load. Connect to GND if not
used.
E. p.
Exposed pad must be connected to SGND
2.3
Description
Power GND
Maximum ratings
Table 2. Absolute maximum ratings
Symbol
Description
Min.
Max.
VIN
40
V
DELAY
-0.3
VCC + 0.3
V
PGND
SGND - 0.3
SGND + 0.3
V
SGND
Unit
V
VCC
-0.3
(VIN + 0.3) OR [max. 4]
V
SS / INH
-0.3
VIN + 0.3
V
-0.3
VCC + 0.3
V
-0.3
VCC + 0.3
V
FB
-0.3
VCC + 0.3
V
FSW
-0.3
VCC + 0.3
V
SYNCH
-0.3
VIN + 0.3
V
VBIAS
-0.3
(VIN + 0.3) OR [max. 6]
V
RST
-0.3
VIN + 0.3
V
LX
-0.3
VIN + 0.3
V
-40
150
°C
MLF
COMP
See Table 1
TJ
Operating temperature range
TSTG
Storage temperature range
-65 to 150
°C
TLEAD
Lead temperature (soldering 10 sec.)
260
°C
IHS, ILS
High-side / low-side switch current
2
A
6/66
DocID025376 Rev 5
L6986
2.4
Pin settings
Thermal data
Table 3. Thermal data
Symbol
Rth JA
2.5
Parameter
Value
Unit
40
C/W
Value
Unit
HBM
2
KV
MM
200
V
CDM
500
V
Thermal resistance junction ambient (device soldered on the
STMicroelectronics® demonstration board)
ESD protection
Table 4. ESD protection
Symbol
ESD
Test condition
DocID025376 Rev 5
7/66
66
Electrical characteristics
3
L6986
Electrical characteristics
TJ = 25 °C, VIN = 12 V unless otherwise specified.
Table 5. Electrical characteristics
Symbol
Parameter
VIN
Operating input voltage range
VINH
VCC UVLO rising threshold
VIN
Operating input voltage range
VINH
Test condition
Note
Min.
Typ.
Max. Unit
4
38
2.7
3.5
4
38
VCC UVLO rising threshold
2.7
3.5
VINL
VCC UVLO falling threshold
2.5
3.5
IPK
Peak current limit
IVY
Valley current limit
ISKIP
IVY_SNK
Duty cycle < 40%
2.6
Duty cycle = 100%
closed loop operation
2.1
A
(1)
LNM or VOUT overvoltage
0.5
0.6
0.8
1
2
RDSON HS High-side RDSON
ISW = 1 A
0.18
0.360
RDSON LS Low-side RDSON
ISW = 1 A
0.15
0.300
fSW
Selected switching frequency
FSW pinstrapping before SS
IFSW
FSW biasing current
SS ended
Low noise mode /
Low consumption mode selection
MLF pinstrapping before SS
MLF biasing current
SS ended
LCM/LNM
IMLF
D
TON MIN
V
2.7
Skip current limit
Reverse current limit
V
see Table 6: fSW selection
0
500
nA
see Table 7: LNM / LCM
selection on page 11
0
(2)
Duty cycle
0
Minimum On time
500
nA
100
%
100
ns
VCC regulator
VCC
SWO
LDO output voltage
VBIAS threshold
VBIAS = GND (no switchover)
2.9
3.3
3.6
VBIAS = 5 V (switchover)
2.9
3.3
3.6
Switch internal supply from VIN
to VBIAS
2.85
3.2
Switch internal supply from
VBIAS to VIN
2.8
3.15
V
Power consumption
ISHTDWN
8/66
Shutdown current from VIN
VSS/INH = GND
DocID025376 Rev 5
4
8
15
A
L6986
Electrical characteristics
Table 5. Electrical characteristics (continued)
Symbol
Parameter
Test condition
LCM - SWO
VREF < VFB < VOVP (SLEEP)
VBIAS = 3.3 V
IQ OPVIN
Quiescent current from VIN
IQ OPVBIAS Quiescent current from VBIAS
LCM - NO SWO
VREF < VFB < VOVP (SLEEP)
VBIAS = GND
Note
Min.
Typ.
(3)
4
10
Max. Unit
15
A
(3)
45
70
100
LNM - SWO
VFB = GND (NO SLEEP)
VBIAS = 3.3 V
0.5
1.5
5
LNM - NO SWO
VFB = GND (NO SLEEP)
VBIAS = GND
2
2.8
6
30
50
90
A
LNM - SWO
VFB = GND (NO SLEEP)
VBIAS = 3.3 V
0.5
1.2
5
mA
SS rising
200
460
700
LCM - SWO
VREF < VFB < VOVP (SLEEP)
VBIAS = 3.3 V
mA
(3)
Soft-start
VINH
VSS threshold
VINH HYST VSS hysteresis
ISS CH
CSS charging current
60
VSS < VINH OR
t < TSS SETUP OR
VEA+ > VFB
t > TSS SETUP AND
VEA+ < VFB
VSS CLMP SS discharge voltage
VSS START
(2)
mV
1
A
(2)
VCC < VCCH OR
t < TSS SETUPOR
thermal fail
Start of internal error amplifier
ramp
4
855
900
945
mV
0.995
1.1
1.150
V
SSGAIN
SS/INH to internal error amplifier
gain
3
VSS END
SS/INH voltage at the end of SS
phase
2.5
3.6
V
0.85
0.859
V
50
500
nA
155
210
S
Error amplifier
VFB
Voltage feedback
IFB
FB biasing current
Gm
Transconductance
AV
Error amplifier gain
0.841
85
(2)
DocID025376 Rev 5
100
dB
9/66
66
Electrical characteristics
L6986
Table 5. Electrical characteristics (continued)
Symbol
ICOMP
Parameter
Test condition
Note
EA output current capability
Min.
Typ.
Max. Unit
±6
±12
±25
A
Inner current loop
gCS
Current sense transconductance
(VCOMP to inductor current gain)
Ipk = 1 A
(4)
(4)
V PP g CS Slope compensation
2.5
A/V
0.4
0.75
1.0
A
Overvoltage protection
VOVP
Overvoltage trip (VOVP/VREF)
1.15
1.2
1.25
VOVP
Overvoltage hysteresis
0.5
2
5
HYST
%
Synchronization (fan out: 6 slave devices typ.)
fSYN MIN
VSYN TH
Synchronization frequency
LNM; fSW = VCC
266.5
SYNCH input threshold
LNM, SYNCH rising
0.70
VSYN HYST SYNCH input threshold hysteresis LNM
ISYN
VSYN OUT
SYNCH pulldown current
LNM, VSYN = 1.2 V
high level output
LNM, 5 mA sinking load
low level output
LNM, 0.7 mA sourcing load
Selected RST threshold
MLF pinstrapping before SS
kHz
1.2
V
20
mV
0.7
mA
1.40
0.6
V
Reset
VTHR
(2)
VTHR HYST RST hysteresis
VRST
RST open collector output
see Table 7: LNM / LCM
selection
2
VIN > VINH AND
VFB < VTH
4 mA sinking load
%
0.4
V
2 < VIN < VINH
4 mA sinking load
0.8
Delay
VTHD
RST open collector released as
soon as VDELAY > VTHD
VFB > VTHR
1.19
ID CH
CDELAY charging current
VFB > VTHR
1
1.234 1.258
2
3
V
A
Thermal shutdown
TSHDWN
Thermal shutdown temperature
(2)
165
THYS
Thermal shutdown hysteresis
(2)
30
C
1. Parameter tested in static condition during testing phase. Parameter value may change over dynamic application condition.
2. Not tested in production.
3. LCM enables SLEEP mode at light load.
4. Measured at fSW = 250 kHz.
10/66
DocID025376 Rev 5
L6986
Electrical characteristics
All the population tested at TJ = 25 °C, VIN = 12 V unless otherwise specified.
Table 6. fSW selection
Symbol
RVCC (E24 series)
fSW
RGND (E24 series)
fSW min.
fSW typ.
fSW max.
Note
275
(1)
0
NC
1.8 k
NC
285
3.3 k
NC
330
5.6 k
NC
380
10 k
NC
435
NC
0
18 k
NC
575
33 k
NC
660
56 k
NC
755
NC
1.8 k
870
NC
3.3 k
NC
5.6 k
1150
NC
10 k
1310
NC
18 k
1500
NC
33 k
1575
1750
1925
NC
56 k
1800
2000
2200
225
250
450
500
900
1000
Unit
(2)
(1)
550
(2)
kHz
1100
(2)
1. Preferred codifications don't require any external resistor.
2. Not tested in production.
All the population tested at TJ = 25 °C, VIN = 12 V unless otherwise specified.
Table 7. LNM / LCM selection
Symbol
VRST
RVCC
(E24 series)
RGND
(E24 series)
0
NC
8.2 k ± 1%
NC
18 k ± 1%
NC
39 k ± 1%
Operating
mode
VRST/VOUT
(tgt value)
VRST min. VRST typ. VRST max. Unit
93%
0.779
0.791
0.802
80%
0.670
0.680
0.690
87%
0.728
0.740
0.751
NC
96%
0.804
0.816
0.828
NC
0
93%
0.779
0.791
0.802
NC
8.2 k ± 1%
80%
0.670
0.680
0.690
NC
18 k ± 1%
87%
0.728
0.740
0.751
NC
39 k ± 1%
96%
0.804
0.816
0.828
LCM
LNM
V
VRST = 0.791 V typical, LNM and LCM preferred codifications don't require any external
resistor.
DocID025376 Rev 5
11/66
66
Functional description
4
L6986
Functional description
The L6986 device is based on a “peak current mode”, constant frequency control. As
a consequence, the intersection between the error amplifier output and the sensed inductor
current generates the PWM control signal to drive the power switch.
The device features LNM (low noise mode) that is forced PWM control, or LCM (low
consumption mode) to increase the efficiency at light load.
The main internal blocks shown in the block diagram in Figure 3 are:
12/66
Embedded power elements. Thanks to the P-channel MOSFET as high-side switch the
device features low dropout operation
A fully integrated sawtooth oscillator with adjustable frequency
A transconductance error amplifier
The high-side current sense amplifier to sense the inductor current
A “Pulse Width Modulator” (PWM) comparator and the driving circuitry of the
embedded power elements
The soft-start blocks to ramp the error amplifier reference voltage and so decreases the
inrush current at power-up. The SS/INH pin inhibits the device when driven low.
The switchover capability of the internal regulator to supply a portion of the quiescent
current when the VBIAS pin is connected to an external output voltage
The synchronization circuitry to manage master / slave operation and the
synchronization to an external clock
The current limitation circuit to implement the constant current protection, sensing
pulse by pulse high-side / low-side switch current. In case of heavy short-circuit the
current protection is fold back to decrease the stress of the external components
A circuit to implement the thermal protection function
The OVP circuitry to discharge the output capacitor in case of overvoltage event
MLF pin strapping sets the LNM/LCM mode and the thresholds of the RST comparator
FSW pinstrapping sets the switching frequency
The RST open collector output
DocID025376 Rev 5
L6986
Functional description
Figure 3. Internal block diagram
&203 6<1& )6: 9,1
66,1+
66,1+
766
3($.
&/
($
)%
293
32:(5
30266
6(16(
3026
26&,//$ 725
95()
/223
/223
&21752/
&21752/
6/23( *1'
'5,9(5
'5,9(5
/;
'(/$<
/1/&
5677+
6(16( 9FF
1026
=(52
&5266,1*
32:(5
1026
*1'
567
9$ //(<
&/
'(/ $< 0/)
*1'
$0
4.1
Power supply and voltage reference
The internal regulator block consists of a start-up circuit, the voltage pre-regulator that
provides current to all the blocks and the bandgap voltage reference. The starter supplies
the startup current when the input voltage goes high and the device is enabled (SS/INH pin
over the inhibits threshold).
The pre-regulator block supplies the bandgap cell and the rest of the circuitry with
a regulated voltage that has a very low supply voltage noise sensitivity.
Switchover feature
The switchover scheme of the pre-regulator block features to derive the main contribution of
the supply current for the internal circuitry from an external voltage (3 V < VBIAS < 5.5 V is
typically connected to the regulated output voltage). This helps to decrease the equivalent
quiescent current seen at VIN. (please refer to Section 4.6: Switchover feature on page 26).
4.2
Voltages monitor
An internal block continuously senses the VCC, VBIAS and VBG. If the monitored voltages are
good, the regulator starts operating. There is also a hysteresis on the VCC (UVLO).
DocID025376 Rev 5
13/66
66
Functional description
L6986
Figure 4. Internal circuit
9&&
67$57(5
35(5(*8/$725
95(*
%$1'*$3
,&%,$6
95()
',1
4.3
Soft-start and inhibit
The soft-start and inhibit features are multiplexed on the same pin. An internal current
source charges the external soft-start capacitor to implement a voltage ramp on the SS/INH
pin. The device is inhibited as long as the SS/INH pin voltage is lower than the VINH
threshold and the soft-start takes place when SS/INH pin crosses VSS START. (see Figure 5:
Soft-start phase).
The internal current generator sources 1 A typ. current when the voltage of the VCC pin
crosses the UVLO threshold. The current increases to 4 A typ. as soon as the SS/INH
voltage is higher than the VINH threshold. This feature helps to decrease the current
consumption in inhibit mode. An external open collector can be used to set the inhibit
operation clamping the SS/INH voltage below VINH threshold.
The startup feature minimizes the inrush current and decreases the stress of the power
components during the power-up phase. The ramp implemented on the reference of the
error amplifier has a gain three times higher (SSGAIN) than the external ramp present at
SS/INH pin.
14/66
DocID025376 Rev 5
L6986
Functional description
Figure 5. Soft-start phase
The CSS is dimensioned accordingly with Equation 1:
Equation 1
I SSCH T SS
4A T SS
C SS = SS GAIN -------------------------------- = 3 --------------------------V FB
0.85V
where TSS is the soft-start time, ISS CH the charging current and VFB the reference of the
error amplifier.
The soft-start block supports the precharged output capacitor.
DocID025376 Rev 5
15/66
66
Functional description
L6986
Figure 6. Soft-start phase with precharged COUT
During normal operation a new soft-start cycle takes place in case of:
Thermal shutdown event
UVLO event
The device is driven in INH mode
The soft-start capacitor is discharged with a 0.6 mA typ. current capability for 1 msec time
max. For complete and proper capacitor discharge in case of fault condition, a maximum
CSS = 67 nF value is suggested.
The application example in Figure 7 shows how to enable the L6986 and perform the softstart phase driven by an external voltage step, for example the signal from the ignition
switch in automotive applications.
Figure 7. Enable the device with external voltage step
ISS CH
Ignition switch
RUP
1PA typ in INHIBIT
4PA typ in SS
SS/INH
UVLO
VSTEP
16/66
RDWN
DocID025376 Rev 5
CSS
Thermal shutdown
ISS DISCH = 600PA typ
L6986
Functional description
The maximum capacitor value has to be limited to guarantee the device can discharge it in
case of thermal shutdown and UVLO events (see Figure 9), so restart the switching activity
ramping the error amplifier reference voltage.
Equation 2
– 1 msec
C SS ------------------------------------------------------------------------------------------V SS_FINAL – 0.9 V
R SS_EQ ln 1 – ----------------------------------------------
600 A – R SS_EQ
where:
Equation 3
R UP R DWN
R SS_EQ = --------------------------------R UP + R DWN
R DWN
V SS_FINAL = V STEP – V DIODE ---------------------------------R UP + R DWN
The optional diode prevents to disable the device if the external source drops to ground.
RUP value is selected in order to make the capacitor charge at first approximation
independent from the internal current generator (4 A typ. current capability, see Table 5 on
page 8), so:
Equation 4
V STEP – V DIODE – V SS END
----------------------------------------------------------------------- » I SS CHARGE 4 A
R UP
where:
Equation 5
V FB
V SS END = V SS START + --------------------SS GAIN
represents the SS/INH voltage correspondent to the end of the ramp on the error amplifier
(see Figure 5); refer to Table 5 for VSS START, VFB and SSGAIN parameters.
As a consequence the voltage across the soft-start capacitor can be written as:
Equation 6
1
v SS t = V SS_FINAL ----------------------------------------t
1–e
– --------------------------------C SS R SS_EQ
RSS_DOWN is selected to guarantee the device stays in inhibit mode when the internal
generator sources 1 A typ. out of the SS/INH pin and VSTEP is not present:
Equation 7
R DWN I SS INHIBIT R DWN 1 A « V INH 200 mV
so:
Equation 8
R DWN 100 k
DocID025376 Rev 5
17/66
66
Functional description
L6986
RUP and RDWN are selected to guarantee:
Equation 9
V SS_FINAL 2 V V SS_END
The time to ramp the internal voltage reference can be calculated from Equation 10:
Equation 10
V SS_FINAL – V SS START
T SS = C SS R SS_EQ ln -----------------------------------------------------------
V SS_FINAL – V SS END
that is the equivalent soft-start time to ramp the output voltage.
Figure 8 shows the soft-start phase with the following component selection: RUP = 180 k,
RDWN = 33 k, CSS = 200 nF, the 1N4148 is a small signal diode and VSTEP = 13 V.
Figure 8. External soft-start network VSTEP driven
The circuit in Figure 7 introduces a time delay between VSTEP and the switching activity that
can be calculated as:
Equation 11
V SS_FINAL
T SS DELAY = C SS R SS_EQ ln -----------------------------------------------------------
V SS_FINAL – V SS START
18/66
DocID025376 Rev 5
L6986
Functional description
Figure 9 shows how the device discharges the soft-start capacitor after an UVLO or thermal
shutdown event in order to restart the switching activity ramping the error amplifier reference
voltage.
Figure 9. External soft-start after UVLO or thermal shutdown
4.3.1
Ratiometric startup
The ratiometric startup is implemented sharing the same soft-start capacitor for a set of the
L6986 device.
DocID025376 Rev 5
19/66
66
Functional description
L6986
Figure 10. Ratiometric startup
9
9287
9287
9287
W
$0
As a consequence all the internal current generators charge in parallel the external
capacitor. The capacitor value is dimensioned accordingly with Equation 12:
Equation 12
I SSCH T SS
4A T SS
C SS = n L6986 SS GAIN -------------------------------- = n L6986 3 --------------------------0.85V
V FB
where nL6986 represents the number of devices connected in parallel.
For better tracking of the different output voltages the synchronization of the set of
regulators is suggested.
20/66
DocID025376 Rev 5
L6986
Functional description
Figure 11. Ratiometric startup operation
4.3.2
Output voltage sequencing
The L6986 device implements sequencing connecting the RST pin of the master device to
the SS/INH of the slave. The slave is inhibited as long as the master output voltage is
outside regulation so implementing the sequencing (see Figure 12).
DocID025376 Rev 5
21/66
66
Functional description
L6986
Figure 12. Output voltage sequencing
9
9287
9287
9287
W
W'(/$<
W'(/$<
W'(/$<
$0
High flexibility is achieved thanks to the programmable RST thresholds (see Table 7: LNM /
LCM selection on page 11) and programmable delay time. To minimize the component
count the DELAY pin capacitor can be also omitted so the pin works as a normal power
good.
4.4
Error amplifier
The voltage error amplifier is the core of the loop regulation. It is a transconductance
operational amplifier whose non inverting input is connected to the internal voltage
reference (0.85 V), while the inverting input (FB) is connected to the external divider or
directly to the output voltage.
Table 8. Uncompensated error amplifier characteristics
Description
Values
Transconductance
155 µS
Low frequency gain
100 dB
The error amplifier output is compared with the inductor current sense information to
perform PWM control. The error amplifier also determines the burst operation at light load
when the LCM is active.
4.5
Light load operation
The MLF pinstrapping during the power-up phase determines the light load operation (refer
to Table 7: LNM / LCM selection).
22/66
DocID025376 Rev 5
L6986
4.5.1
Functional description
Low noise mode (LNM)
The low noise mode implements a forced PWM operation over the different loading
conditions. The LNM features a constant switching frequency to minimize the noise in the
final application and a constant voltage ripple at fixed VIN. The regulator in steady loading
condition never skip pulses and it operates in continuous conduction mode (CCM) over the
different loading conditions.
Figure 13. Low noise mode operation
Typical applications for the LNM operation are car audio, sensors.
4.5.2
Low consumption mode (LCM)
The low consumption mode maximizes the efficiency at light load. The regulator prevents
the switching activity whenever the switch peak current request is lower than the ISKIP
threshold (700 mA typical). As a consequence the L6986 device works in bursts and it
minimizes the quiescent current request in the meantime between the switching operation.
DocID025376 Rev 5
23/66
66
Functional description
L6986
Figure 14. LCM operation at zero load
Given the energy stored in the inductor during a burst, the voltage ripple depends on the
capacitor value:
Equation 13
T
BURST
Q IL
0 iL t dt
V OUT RIPPLE = -------------- = -------------------------------------------C OUT
C OUT
24/66
DocID025376 Rev 5
L6986
Functional description
Figure 15. LCM operation over loading condition (part 1)
Figure 16. LCM operation over loading condition (part 2)
DocID025376 Rev 5
25/66
66
Functional description
L6986
Figure 17. The regulator works in CCM
4.6
Switchover feature
The switchover maximizes the efficiency at light load that is crucial for LCM applications.
4.6.1
LCM
The LCM operation satisfies the high efficiency requirements of the battery powered
applications. In order to minimize the regulator quiescent current request from the input
voltage, the VBIAS pin can be connected to an external voltage source in the range
3 V < VBIAS < 5.5 V (see Section 4.1: Power supply and voltage reference on page 13).
In case the VBIAS pin is connected to the regulated output voltage (VOUT), the total current
drawn from the input voltage can be calculated as:
Equation 14
V BIAS
1
I QVIN = I QOPVIN + ----------------- --------------- I QOPVBIAS
V IN
L6986
where IQ OP VIN, IQ OP VBIAS are defined in Table 5: Electrical characteristics on page 8
and L6986 is the efficiency of the conversion in the working point.
4.6.2
LNM
Equation 14 is also valid when the device works in LNM and it can increase the efficiency at
medium load since the regulator always operates in continuous conduction mode.
26/66
DocID025376 Rev 5
L6986
4.7
Functional description
Overcurrent protection
The current protection circuitry features a constant current protection, so the device limits
the maximum peak current (see Table 5: Electrical characteristics on page 8) in overcurrent
condition.
The L6986 device implements a pulse by pulse current sensing on both power elements
(high-side and low-side switches) for effective current protection over the duty cycle range.
The high-side current sensing is called “peak” the low-side sensing “valley”.
The internal noise generated during the switching activity makes the current sensing
circuitry ineffective for a minimum conduction time of the power element. This time is called
“masking time” because the information from the analog circuitry is masked by the logic to
prevent an erroneous detection of the overcurrent event. As a consequence, the peak
current protection is disabled for a masking time after the high-side switch is turned on, the
valley for a masking time after the low-side switch is turned on. In other words, the peak
current protection can be ineffective at extremely low duty cycles, the valley current
protection at extremely high duty cycles.
The L6986 device assures an effective overcurrent protection sensing the current flowing in
both power elements. In case one of the two current sensing circuitry is ineffective because
of the masking time, the device is protected sensing the current on the opposite switch.
Thus, the combination of the “peak” and “valley” current limits assure the effectiveness of
the overcurrent protection even in extreme duty cycle conditions.
The valley current threshold is designed higher than the peak to guarantee a proper
operation. In case the current diverges because of the high-side masking time, the low-side
power element is turned on until the switch current level drops below the valley current
sense threshold. The low-side operation is able to prevent the high-side turn on, so the
device can skip pulses decreasing the swathing frequency.
DocID025376 Rev 5
27/66
66
Functional description
L6986
Figure 18. Valley current sense operation in overcurrent condition
Figure 18 shows the switching frequency reduction during the valley current sense
operation in case of extremely low duty cycle (VIN 38 V, fSW = 500 kHz short-circuit
condition).
In worst case scenario (like Figure 18) of the overcurrent protection the switch current is
limited to:
Equation 15
V IN – V OUT
I MAX = I VALLEYTH + ------------------------------ T MASKHS
L
where IVALLEY_TH is the current threshold of the valley sensing circuitry (see Table 5:
Electrical characteristics on page 8) and TMASK_HS is the masking time of the high-side
switch 100 nsec. typ.).
In most of the overcurrent conditions the conduction time of the high-side switch is higher
than the masking time and so the peak current protection limits the switch current.
Equation 16
IMAX = IPEAK_TH
28/66
DocID025376 Rev 5
L6986
Functional description
Figure 19. Peak current sense operation in overcurrent condition
The DC current flowing in the load in overcurrent condition is:
Equation 17
I RIPPLE V OUT
V IN – V OUT
I DCOC V OUT = I MAX – ---------------------------------------- = I MAX – ------------------------------ T ON
2
2L
OCP and switchover feature
Output capacitor discharging the current flowing to ground during heavy short-circuit events
is only limited by parasitic elements like the output capacitor ESR and short-circuit
impedance.
Due to parasitic inductance of the short-circuit impedance, negative output voltage
oscillations can be generated with huge discharging current levels (see Figure 20).
DocID025376 Rev 5
29/66
66
Functional description
L6986
Figure 20. Output voltage oscillations during heavy short-circuit
inductor current
short-circuit current
switching node
regulated output voltage
Figure 21. Zoomed waveform
inductor current
short-circuit current
switching node
regulated output voltage
The VBIAS pin absolute maximum ratings (see Table 2: Absolute maximum ratings on
page 6) must be satisfied over the different dynamic conditions.
If VBIAS is connected to GND there are no issues (see Figure 20 and Figure 21).
30/66
DocID025376 Rev 5
L6986
Functional description
A small resistor value (few ohms) in series with VBIAS can help to limit the pin negative
voltage (see Figure 22) during heavy short-circuit events if it is connected to the regulated
output voltage.
Figure 22. VBIAS in heavy short-circuit event
inductor current
switching node
VBIAS pin voltage
(cyan)
regulated output voltage
(purple)
4.8
Overvoltage protection
The overvoltage protection monitors the FB pin and enables the low-side MOSFET to
discharge the output capacitor if the output voltage is 20% over the nominal value.
This is a second level protection and should never be triggered in normal operating
conditions if the system is properly dimensioned. In other words, the selection of the
external power components and the dynamic performance determined by the compensation
network should guarantee an output voltage regulation within the overvoltage threshold
even during the worst case scenario in term of load transitions.
The protection is reliable and also able to operate even during normal load transitions for
a system whose dynamic performance is not in line with the load dynamic request. As
a consequence the output voltage regulation would be affected.
Figure 23 shows the overvoltage operation during a negative steep load transient for
a system designed with huge inductor value and small output capacitor. The inductor value
limits the switch current slew rate and the extra charge flowing into the small capacitor value
generates an overvoltage event. This can be considered as an example for a system with
dynamic performance not in line with the load request.
The L6986 device implements a 1 A typ. negative current limitation to limit the maximum
reversed switch current during the overvoltage operation.
DocID025376 Rev 5
31/66
66
Functional description
L6986
Figure 23. Overvoltage operation
OVP
negative current limitation in OVP
4.9
Thermal shutdown
The shutdown block disables the switching activity if the junction temperature is higher than
a fixed internal threshold (165 °C typical). The thermal sensing element is close to the
power elements, ensuring fast and accurate temperature detection. A hysteresis of
approximately 30 °C prevents the device from turning ON and OFF continuously. When the
thermal protection runs away a new soft-start cycle will take place.
32/66
DocID025376 Rev 5
L6986
5
Closing the loop
Closing the loop
Figure 24. Block diagram of the loop
9,1
3:0FRQWURO
&XUUHQWVHQVH
+6
VZ LWFK
/&ILOWHU
5HVLVWRUGLYLGHU
/
,+6 J &6
/6
&287
VZ LWFK
5
&RPSHQVDWLRQ QHWZRUN
3:0FRPSDUDWRU
&3
5&
)%
5/2$'
95()
5
(UURUDPSOLILHU
&&
$0
5.1
GCO(s) control to output transfer function
The accurate control to output transfer function for a buck peak current mode converter can
be written as:
Equation 18
G CO s
s
1 + ----
R LOAD
1
z
= ------------------ -------------------------------------------------------------------------------------------------------- ---------------------- F H s
R LOAD T SW
Ri
s
------
1 + ----------------------------------- m C 1 – D – 0.5 1 +
L
p
where RLOAD represents the load resistance, Ri the equivalent sensing resistor of the
current sense circuitry,p the single pole introduced by the power stage and z the zero
given by the ESR of the output capacitor.
FH(s) accounts the sampling effect performed by the PWM comparator on the output of the
error amplifier that introduces a double pole at one half of the switching frequency.
DocID025376 Rev 5
33/66
66
Closing the loop
L6986
Equation 19
1
z = --------------------------------ESR C OUT
Equation 20
m c 1 – D – 0.5
1
p = --------------------------------------- + ---------------------------------------------L C OUT f SW
R LOAD C OUT
where:
Equation 21
Se
m C = 1 + -----Sn
S = V g f
PP
CS SW
e
V
–
V
IN
OUT
S = --------------------------- n
L
Sn represents the on time slope of the sensed inductor current, Se the on time slope of the
external ramp (VPP peak-to-peak amplitude) that implements the slope compensation to
avoid sub-harmonic oscillations at duty cycle over 50%.
Se can be calculated from the parameter VPP gCS given in Table 5 on page 8.
The sampling effect contribution FH(s) is:
Equation 22
1
F H s = --------------------------------------------2
s
s
1 + -------------------- + --------2n Qp
n
where:
Equation 23
1
Q p = ----------------------------------------------------------- m c 1 – D – 0.5
34/66
DocID025376 Rev 5
L6986
5.2
Closing the loop
Error amplifier compensation network
The typical compensation network required to stabilize the system is shown in Figure 25.
Figure 25. Transconductance embedded error amplifier
95()
)%
($
&203
5&
&3
&&
9
5
G9
*P G9
&
5&
&3
&&
9
$0
RC and CC introduce a pole and a zero in the open loop gain. CP does not significantly affect
system stability but it is useful to reduce the noise at the output of the error amplifier.
The transfer function of the error amplifier and its compensation network is:
Equation 24
A V0 1 + s R c C c
A 0 s = --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------2
s R0 C0 + Cp Rc Cc + s R0 Cc + R0 C0 + Cp + Rc Cc + 1
Where Avo = Gm · Ro
The poles of this transfer function are (if Cc >> C0 + CP):
Equation 25
1
f PLF = ------------------------------------2 R0 Cc
DocID025376 Rev 5
35/66
66
Closing the loop
L6986
Equation 26
whereas the zero is defined as:
1
f PHF = -------------------------------------------------------2 R0 C0 + Cp
Equation 27
1
f Z = ------------------------------------2 Rc Cc
5.3
Voltage divider
The contribution of a simple voltage divider is:
Equation 28
R2
G DIV s = -------------------R1 + R2
A small signal capacitor in parallel to the upper resistor (see Figure 26) of the voltage divider
implements a leading network (fzero < fpole), sometimes necessary to improve the system
phase margin:
Figure 26. Leading network example
9,1
9,1
567
9%,$6
*1'
3:5JQG
3*1'
/;
3*1'
/;
0/)
9287
&U
/
5
9&&
66,1+
)%
'(/$<
&203
)6:
6*1' (3
6<1&+
5F
&S
&F
5
3:5JQG
*1'
VLJQDO*1'
$0
Laplace transformer of the leading network:
Equation 29
1 + s + R 1 C R1
R2
G DIV s = -------------------- ------------------------------------------------------------R1 + R2
R1 R2
1 + s -------------------- C R1
R1 + R2
36/66
DocID025376 Rev 5
L6986
Closing the loop
where:
Equation 30
1
f Z = ----------------------------------------2 R 1 C R1
1
f p = ------------------------------------------------------R1 R2
2 -------------------- C R1
R1 + R2
fZ fp
5.4
Total loop gain
In summary, the open loop gain can be expressed as:
Equation 31
G s = G DIV s G CO s A 0 s
Example 1
VIN = 12 V, VOUT = 3.3 V, ROUT = 2.2
Selecting L = 6.8 µH, COUT = 15 µF and ESR = 1 m, RC= 68 k, CC= 180 pF,
CP = 6.8 pF (please refer to Example 2), the gain and phase bode diagrams are plotted
respectively in Figure 27 and Figure 28.
DocID025376 Rev 5
37/66
66
Closing the loop
L6986
Figure 27. Module plot
0RGXOH>G%@
(;7(51$//22302'8/(
[
[
[
[
[
)UHTXHQF\>+]@
$0
Equation 32
BW = 67kHz
Phase margin = 53
38/66
DocID025376 Rev 5
0
L6986
Closing the loop
Figure 28. Phase plot
(;7(51$//223*$,13+$6(
[
[
[
[
[
$0
The blue solid trace represents the transfer function including the sampling effect term (see
Equation 21 on page 34), the dotted blue trace neglects the contribution.
5.5
Compensation network design
The maximum bandwidth of the system can be designed up to fSW/6 to guarantee a valid
small signal model.
Equation 33
f SW
BW = --------6
Equation 34
2 BW C OUT V OUT
R C = ---------------------------------------------------------------0.85V g CS g m TYP
where:
Equation 35
p
f POLE = ----------2
p is defined by Equation 20 on page 34, gCS represents the current sense
transconductance (see Table 5: Electrical characteristics on page 8) and gm TYP the error
amplifier transconductance.
DocID025376 Rev 5
39/66
66
Closing the loop
L6986
Equation 36
5
C C = -------------------------------------2 R C BW
Example 2
Considering VIN = 12 V, VOUT = 3.3 V, L = 6.8 H, COUT = 15 F, fSW = 500 kHz.
The maximum system bandwidth is 80 kHz. Assuming to design the compensation network
to achieve a system bandwidth of 70 kHz:
Equation 37
f POLE = 6kHz
Equation 38
V OUT
R LOAD = -------------- = 2.2
I OUT
so accordingly with Equation 34 and Equation 36:
Equation 39
R C = 68k
Equation 40
C C = 168pF 180pF
40/66
DocID025376 Rev 5
L6986
Application notes
6
Application notes
6.1
Output voltage adjustment
The error amplifier reference voltage is 0.85 V typical.
The output voltage is adjusted accordingly with Equation 41 (see Figure 29):
Equation 41
R1
V OUT = 0.85 1 + -------
R2
Cr1 capacitor is sometimes useful to increase the small signal phase margin (please refer to
Section 5.5: Compensation network design).
Figure 29. L6986 application circuit
9,1
9,1
567
9%,$6
*1'
3:5JQG
3*1'
/;
3*1'
/;
0/)
9287
&U
/
5
9&&
66,1+
)%
'(/$<
&203
)6:
6*1' (3
6<1&+
5F
&S
&F
5
*1'
VLJQDO*1'
3:5JQG
$0
6.2
Switching frequency
A resistor connected to the FSW pin features the selection of the switching frequency. The
pinstrapping is performed at power-up, before the soft-start takes place. The FSW pin is
pinstrapped and then driven floating in order to minimize the quiescent current from VIN.
Please refer toTable 6: fSW selection on page 11 to identify the pull-up / pull-down resistor
value. fSW = 250 kHz / fSW = 500 kHz preferred codifications don't require any external
resistor.
6.3
MLF pin
A resistor connected to the MLF pin features the selection of the between low noise mode /
low consumption mode and the different RST thresholds. The pinstrapping is performed at
power-up, before the soft-start takes place. The FSW pin is pinstrapped and then driven
floating in order to minimize the quiescent current from VIN.
DocID025376 Rev 5
41/66
66
Application notes
L6986
Please refer to Table 7: LNM / LCM selection on page 11 to identify the pull-up / pull-down
resistor value. (LNM, RST threshold 93%) / (LCM, RST threshold 93%) preferred
codifications don't require any external resistor.
6.4
Voltage supervisor
The embedded voltage supervisor (composed of the RST and the DELAY pins) monitors the
regulated output voltage and keeps the RST open collector output in low impedance as long
as the VOUT is out of regulation. In order to ensure a proper reset of digital devices with
a valid power supply, the device can delay the RST assertion with a programmable time.
Figure 30. Voltage supervisor operation
The comparator monitoring the FB voltage has four different programmable thresholds
(80%, 87%, 93%, 96% nominal output voltage) for high flexibility (see Section 6.3: MLF pin
and Table 7: LNM / LCM selection on page 11).
When the RST comparator detects the output voltage is in regulation, a 2 A internal current
source starts to charge an external capacitor to implement a voltage ramp on the DELAY
pin. The RST open collector is then released as soon as VDELAY = 1.234 V (see Figure 30).
The CDELAY is dimensioned accordingly with Equation 42:
Equation 42
I SSCH T DELAY
2A T DELAY
C DELAY = ------------------------------------------ = ------------------------------------V DELAY
1.234V
The maximum suggested capacitor value is 270 nF.
42/66
DocID025376 Rev 5
L6986
Synchronization (LNM)
Beating frequency noise is an issue when multiple switching regulators populate the same
application board. The L6986 synchronization circuitry features the same switching
frequency for a set of regulators simply connecting their SYNCH pin together, so preventing
beating noise. The master device provides the synchronization signal to the others since the
SYNCH pin is I/O able to deliver or recognize a frequency signal.
For proper synchronization of multiple regulators, all of them have to be configured with the
same switching frequency (see Table 6), so the same resistor connected at the FSW pin.
In order to minimize the RMS current flowing through the input filter, the L6986 device
provides a phase shift of 180° between the master and the SLAVES. If more than two
devices are synchronized, all slaves will have a common 180° phase shift with respect to
the master.
Considering two synchronized L6986 which regulates the same output voltage (i.e.
operating with the same duty cycle), the input filter RMS current is optimized and is
calculated as:
Equation 43
I RMS
I
OUT
----------- 2D 1 – 2D
2
=
I OUT
- 2D – 1 2 – 2D
---------- 2
if D < 0.5
if D > 0.5
The graphical representation of the input RMS current of the input filter in the case of two
devices with 0° phase shift (synchronized to an external signal) or 180° phase shift
(synchronized connecting their SYNCH pins) regulating the same output voltage is provided
in Figure 31. To dimension the proper input capacitor please refer to Chapter 6.6.1: Input
capacitor selection.
Figure 31. Input RMS current
506FXUUHQWQRUPDOL]HG,UPV,287
6.5
Application notes
WZR UHJXODWRUV RSHUDWLQJ LQ SKDVH
WZR UHJXODWRUV RSHUDWLQJ RXW RI SKDVH
DocID025376 Rev 5
43/66
66
Application notes
L6986
Figure 32 shows two regulators not synchronized.
Figure 32. Two regulators not synchronized
Figure 33 shows the same regulators working synchronized. The MASTER regulator (LX2
trace) delivers the synchronization signal (SYNCH1, SYNCH2 pins are connected together)
to the SLAVE device (LX1). The SLAVE regulator works in phase with the synchronization
signal which is out of phase with the MASTER switching operation.
Figure 33. Two regulators synchronized
44/66
DocID025376 Rev 5
L6986
Application notes
Multiple L6986 can be synchronized to an external frequency signal fed to the SYNCH pin.
In this case the regulator is phased to the reference and all the devices will work with 0°
phase shift.
The frequency range of the synchronization signal is 275 kHz - 2 MHz and the minimum
pulse width is 100 nsec (see Figure 34).
Figure 34. Synchronization pulse definition
275kHz < fSYNCHRO < 2MHz
fSYNCHRO
fSYNCHRO
100nsec min.
100nsec min.
Since the slope compensation contribution that is required to prevent subharmonic
oscillations in peak current mode architecture depends on the switching frequency, it is
important to select the same oscillator frequency for all regulators (all of them operate as
SLAVE) as close as possible to the frequency of the reference signal (please refer to
Table 6: fSW selection on page 11). As a consequence all the regulators have the same
resistor value connected to the FSW pin, so the slope compensation is optimized
accordingly with the frequency of the synchronization signal. The slope compensation
contribution is latched at power-up and so fixed during the device operation.
The L6986 normally operates in MASTER mode, driving the SYNCH line at the selected
oscillator frequency as shown in Figure 35 and Figure 36.
In SLAVE mode the L6986 sets the internal oscillator at 250 kHz typ. (see Table 6 on
page 11 - first row) and drives the line accordingly.
Figure 35. L6986 synchronization driving capability
VCC INT
5 mA
fOSC
150nsec typ.
HIGH LEVEL
LOW LEVEL
0.7 mA
In order to safely guarantee that each regulator recognizes itself in SLAVE mode during the
normal operation, the external master must drive the SYNCH pin with a clock signal
DocID025376 Rev 5
45/66
66
Application notes
L6986
frequency higher than the maximum oscillator spread (refer to Table 6 on page 11) for at
least 10 internal clock cycles.
For example: selecting RFSW = 0 to GND
Table 9. Example of oscillator frequency selection from Table 6
Symbol
RVCC (E24 series)
RGND (E24 series)
fSW min.
fSW typ.
fSW max.
fSW
NC
0
450
500
550
the device enters in slave mode after 10 pulses at frequency higher than 550 kHz and so it
is able to synchronize to a clock signal in the range 275 kHz - 2 MHz (see Figure 34).
Anyway it is suggested to limit the frequency range within ± 20% FSW resistor nominal
frequency (see details in text below). If not spread spectrum is required, all the regulators
synchronize to a frequency higher to the maximum oscillator spread (550 kHz in the
example).
The device keeps operating in slave mode as far as the master is able to drive the SYNCH
pin faster than 275 kHz (maximum oscillator spread for 250 kHz oscillator), otherwise it goes
back into MASTER mode at the nominal oscillator frequency after successfully driving one
pulse at 250 kHz (see Figure 36) in the SYNCH line.
Figure 36. Slave to master mode transition
switching node
SLAVE mode
250kHz typ. stand alone operation at nominal fsw
SYNCH signal
The external master can force a latched SLAVE mode driving the SYNCH pin low at powerup, before the soft-start starts the switching activity. So the oscillator frequency is 250 kHz
typ. fixed until a new UVLO event is triggered regardless FSW resistor value, that otherwise
counts to design the slope compensation. The same considerations above are also valid.
The master driving capability must be able to provide the proper signal levels at the SYNCH
pin (see Table 5 on page 8 - Synchronization section):
46/66
DocID025376 Rev 5
L6986
Application notes
Low level < VSYN THL= 0.7 V sinking 5 mA
High level > VSYN THH = 1.2 V sourcing 0.7 mA
Figure 37. Master driving capability to synchronize the L6986
VCCM
5 mA
VSYN_TH_H
0.7 mA
VSYN_TH_L
RH
RL
As anticipated above, in SLAVE mode the internal oscillator operates at 250 kHz typ. but the
slope compensation is dimensioned accordingly with FSW resistors so, even if the L6986
supports synchronization over the 275 kHz - 2 MHz frequency range, it is important to limit
the switching operation around a working point close to the selected frequency (FSW
resistor).
As a consequence, to guarantee the full output current capability and to prevent the
subharmonic oscillations the master must limit the driving frequency range within ± 20% of
the selected frequency.
A wider frequency range may generate subharmonic oscillation for duty > 50% or limit the
peak current capability (see IPK parameter in Table 5) since the internal slope compensation
signal may be saturated.
Since the slope compensation contribution, that is required to prevent subharmonic
oscillations in peak current mode architecture, depends on the switching frequency, it is
important to select the same switching frequency for all regulators (all of them operate as
SLAVE) one step lower than the reference signal (please refer to Table 6: fSW selection on
page 11). As a consequence, all the regulators have the same resistor connected to the
FSW pin.
6.6
Design of the power components
6.6.1
Input capacitor selection
The input capacitor voltage rating must be higher than the maximum input operating voltage
of the application. During the switching activity a pulsed current flows into the input capacitor
and so its RMS current capability must be selected accordingly with the application
conditions. Internal losses of the input filter depends on the ESR value so usually low ESR
capacitors (like multilayer ceramic capacitors) have higher RMS current capability. On the
DocID025376 Rev 5
47/66
66
Application notes
L6986
other hand, given the RMS current value, lower ESR input filter has lower losses and so
contributes to higher conversion efficiency.
The maximum RMS input current flowing through the capacitor can be calculated as:
Equation 44
D D
I RMS = I OUT 1 – ---- ---
Where IO is the maximum DC output current, D is the duty cycles, is the efficiency. This
function has a maximum at D = 0.5 and, considering = 1, it is equal to Io/2.
In a specific application the range of possible duty cycles has to be considered in order to
find out the maximum RMS input current. The maximum and minimum duty cycles can be
calculated as:
Equation 45
V OUT + V LOWSIDE
D MAX = -----------------------------------------------------------------------------------------------V INMIN + V LOWSIDE – V HIGHSIDE
Equation 46
V OUT + V LOWSIDE
D MIN = -------------------------------------------------------------------------------------------------V INMAX + V LOWSIDE – V HIGHSIDE
Where VHIGH_SIDE and VLOW_SIDE are the voltage drops across the embedded switches.
The peak to peak voltage across the input filter can be calculated as:
Equation 47
I OUT
D D
V PP = ------------------------- 1 – ---- ---- + ESR I OUT + I L
C IN f SW
In case of negligible ESR (MLCC capacitor) the equation of CIN as a function of the target
VPP can be written as follows:
Equation 48
I OUT
D D
C IN = -------------------------- 1 – ---- ---V PP f SW
Considering this function has its maximum in D = 0.5:
Equation 49
I OUT
C INMIN = ---------------------------------------------4 V PPMAX f SW
Typically CIN is dimensioned to keep the maximum peak-peak voltage across the input filter
in the order of 5% VIN_MAX.
48/66
DocID025376 Rev 5
L6986
Application notes
Table 10. Input capacitors
Manufacturer
TDK
Taiyo Yuden
6.6.2
Series
Size
Cap value (F)
Rated voltage (V)
C3225X7S1H106M
1210
10
50
C3216X5R1H106M
1206
UMK325BJ106MM-T
1210
Inductor selection
The inductor current ripple flowing into the output capacitor determines the output voltage
ripple (please refer to Section 6.6.3). Usually the inductor value is selected in order to keep
the current ripple lower than 20% - 40% of the output current over the input voltage range.
The inductance value can be calculated by Equation 50:
Equation 50
V IN – V OUT
V OUT
I L = ------------------------------ T ON = -------------- T OFF
L
L
Where TON and TOFF are the on and off time of the internal power switch. The maximum
current ripple, at fixed VOUT, is obtained at maximum TOFF that is at minimum duty cycle
(see Section 6.6.1: Input capacitor selection to calculate minimum duty). So fixing IL = 20%
to 40% of the maximum output current, the minimum inductance value can be calculated:
Equation 51
V OUT 1 – D MIN
L MIN = ------------------- ----------------------F SW
I LMAX
where fSW is the switching frequency 1/(TON + TOFF).
For example for VOUT = 3.3 V, VIN = 12 V, IO = 2 A and FSW = 500 kHz the minimum
inductance value to have IL = 30% of IO is about 8.2 µH.
The peak current through the inductor is given by:
Equation 52
I L
I L PK = I OUT + -------2
So if the inductor value decreases, the peak current (that has to be lower than the current
limit of the device) increases. The higher is the inductor value, the higher is the average
output current that can be delivered, without reaching the current limit.
In Table 11 some inductor part numbers are listed.
Table 11. Inductors
Manufacturer
Series
Inductor value (H)
Saturation current (A)
Coilcraft
XAL50xx
2.2 to 22
6.5 to 2.7
XAL60xx
2.2 to 22
12.5 to 4
DocID025376 Rev 5
49/66
66
Application notes
6.6.3
L6986
Output capacitor selection
The triangular shape current ripple (with zero average value) flowing into the output
capacitor gives the output voltage ripple, that depends on the capacitor value and the
equivalent resistive component (ESR). As a consequence the output capacitor has to be
selected in order to have a voltage ripple compliant with the application requirements.
The voltage ripple equation can be calculated as:
Equation 53
I LMAX
V OUT = ESR I LMAX + --------------------------------------8 C OUT f SW
Usually the resistive component of the ripple can be neglected if the selected output
capacitor is a multi layer ceramic capacitor (MLCC).
The output capacitor is important also for loop stability: it determines the main pole and the
zero due to its ESR. (see Section 5: Closing the loop on page 33 to consider its effect in the
system stability).
For example with VOUT = 3.3 V, VIN = 12 V, IL = 0.6 A, fSW = 500 kHz (resulting by the
inductor value) and COUT = 10 F MLCC:
Equation 54
V OUT
I LMAX
1
1
0 6
15mV
------------------ -------------- ------------------------------ = ------ -------------------------------------------------- = ---------------- = 0.45%
33 8 10F 500kHz
V OUT V OUT C OUT f SW
3.3
The output capacitor value has a key role to sustain the output voltage during a steep load
transient. When the load transient slew rate exceeds the system bandwidth, the output
capacitor provides the current to the load. In case the final application specifies high slew
rate load transient, the system bandwidth must be maximized and the output capacitor has
to sustain the output voltage for time response shorter than the loop response time.
In Table 12 some capacitor series are listed.
Table 12. Output capacitors
Manufacturer
Series
Cap value (F)
Rated voltage (V)
ESR (m)
GRM32
22 to 100
6.3 to 25
<5
GRM31
10 to 47
6.3 to 25
<5
ECJ
10 to 22
6.3
<5
EEFCD
10 to 68
6.3
15 to 55
SANYO
TPA/B/C
100 to 470
4 to 16
40 to 80
TDK
C3225
22 to 100
6.3
<5
MURATA
PANASONIC
50/66
DocID025376 Rev 5
L6986
Application board
7
Application board
The reference evaluation board schematic is shown in Figure 38.
Figure 38. Evaluation board schematic
5
10
73
8
73
6<1&+
9,1B)/7
9
9
5
10
5
X)
10
X)
&
&
&
&
&
10
Q)
9
5
10
5
6<1&+
567
9,1
9%,$6
9&&
/;
/;
5
)%
/
'(/$<
Q)
Q)
9287
X+
&203
6*1'
&
66,1+
&
73
-
0/)
&
0
-
)6:
(3
-
567
/
5
&
3*1' 3*1'
N &
S
5
N
S
VLJQDO*1'
10
5
N
10
&
5
X) 9
5
&
73
66,1+
73
SRZHU*1'
3*1'
*1'
/
73
/
73
X+
9,1B)/7
9,1
10
VL]H
X)
X)
&
73
&
10
&
9,1B(0,
3*1'
*1'
$0
The additional input filter (C16, L3, C15, L2, C14) limits the conducted emission on the
power supply.
Table 13. Bill of material
Reference
Part number
Description
Manufacturer
C1
CGA5L3X5R1H106K
10 F - 1206 - 50 V - X7R - 10%
TDK
C2
C2012X7S2A105K
1 F - 0805 - 50 V - X7S - 10%
TDK
C3
470 nF - 50 V - 0603
C4
2.2 pF - 50 V - 0603
C5
68 nF - 50 V - 0603
C6
10 nF - 50 V - 0603
C8
120 pF - 50 V - 0603
C1
CGA5L3X5R1H106K
10 F - 1206 - 50 V - X7R - 10%
TDK
C9
C3216X5R1C476M
47 F - 1206 - 16 V - X5R - 20%
TDK
C14, C15, C16
C3216X7R1H475K160AC
4.7 F - 1206 - 50 V - X7R - 10%
TDK
C7, C10, C11, C13
Not mounted
R1, R4
0 R - 0603
DocID025376 Rev 5
51/66
66
Application board
L6986
Table 13. Bill of material (continued)
Reference
Part number
Description
R6
1 M - 1%- 0603
R7
180 k - 1% - 0603
R8
130 k - 1% - 0603
R9
62 k - 1% - 0603
R11
10 - 1% - 0603
R2, R3, R5, R10
Not mounted
Manufacturer
L1
XAL5050-103MEC
10 H
Coilcraft
L2
XAL5030-472MEC
4.7 H
Coilcraft
L3
MPZ2012S221A
EMC bead
TDK
J1
Open
J2
Open
J3
Closed
J4
Open
U1
L6986
Switchover
STM
Figure 39 and Figure 40 show the magnitude and phase margin Bode’s plots related to the
evaluation board presented in Figure 38.
The small signal dynamic performance of the demonstration board is:
Equation 55
BW = 67kHz
phase margin = 53
52/66
DocID025376 Rev 5
0
L6986
Application board
Figure 39. Magnitude Bode’s plot
0RGXOH>G%@
(;7(51$//22302'8/(
[
[
[
[
[
)UHTXHQF\>+]@
$0
Figure 40. Phase margin Bode’s plot
(;7(51$//223*$,13+$6(
3KDVH
X
[
[
[
[
)UHTXHQF\>+]@
$0
DocID025376 Rev 5
53/66
66
Application board
L6986
Figure 41. Top layer
Figure 42. Bottom layer
54/66
DocID025376 Rev 5
L6986
8
Efficiency curves
Efficiency curves
Figure 43. Efficiency curves over fsw: VIN = 13.5 V - VOUT = 3.3 V
90
85
80
75
70
65
60
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
VIN=13.5V VOUT=3.3V A6986 500kHz VBIAS PSKIP
VIN=13.5V VOUT=3.3VA6986 500kHz NOVBIAS PSKIP
VIN=13.5V VOUT=3.3V A6986 500kHz NOVBIAS NOPSKIP
VIN=13.5V VOUT=3.3V A6986 500kHz VBIAS NOPSKIP
VIN=13.5V VOUT=3.3V 1MHz VBIAS PSKIP
VIN=13.5V VOUT=3.3V 1MHz NOVBIAS PSKIP
VIN=13.5V VOUT=3.3V 1MHz NOVBIAS NOPSKIP
VIN=13.5V VOUT=3.3V 1MHz VBIAS NOPSKIP
VIN=13.5V VOUT=3.3V 2MHz VBIAS NOSPKIP
VIN=13.5V VOUT=3.3V 2MHz NOVBIAS NOSPKIP
VIN=13.5V VOUT=3.3V 2MHz NOVBIAS SPKIP
VIN=13.5V VOUT=3.3V 2MHz VBIAS SPKIP
2
Figure 44. Efficiency curves over fsw: VIN = 13.5 V - VOUT = 3.3 V (log scale)
90
85
80
75
70
65
60
0.0015
0.015
0.15
VIN=13.5V VOUT=3.3V A6986 500kHz VBIAS PSKIP
VIN=13.5V VOUT=3.3VA6986 500kHz NOVBIAS PSKIP
VIN=13.5V VOUT=3.3V A6986 500kHz NOVBIAS NOPSKIP
VIN=13.5V VOUT=3.3V A6986 500kHz VBIAS NOPSKIP
VIN=13.5V VOUT=3.3V 1MHz VBIAS PSKIP
VIN=13.5V VOUT=3.3V 1MHz NOVBIAS PSKIP
VIN=13.5V VOUT=3.3V 1MHz NOVBIAS NOPSKIP
VIN=13.5V VOUT=3.3V 1MHz VBIAS NOPSKIP
VIN=13.5V VOUT=3.3V 2MHz VBIAS NOSPKIP
VIN=13.5V VOUT=3.3V 2MHz NOVBIAS NOSPKIP
VIN=13.5V VOUT=3.3V 2MHz NOVBIAS SPKIP
VIN=13.5V VOUT=3.3V 2MHz VBIAS SPKIP
DocID025376 Rev 5
55/66
66
Efficiency curves
L6986
Figure 45. Efficiency curves over fsw: VIN = 13.5 V - VOUT = 5 V
95
90
85
80
75
70
65
60
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
VIN=13.5V VOUT=5V A6986 500kHz VBIAS NOPSKIP
VIN=13.5V VOUT=5V A6986 500kHz NOVBIAS NOPSKIP
VIN=13.5V VOUT=5V A6986 500kHz NOVBIAS PSKIP
VIN=13.5V VOUT=5V A6986 500kHz VBIAS PSKIP
VIN=13.5V VOUT=5V 1MHz VBIAS NOSPKIP
VIN=13.5V VOUT=5V 1MHz NOVBIAS NOSPKIP
VIN=13.5V VOUT=5V 1MHz NOVBIAS SPKIP
VIN=13.5V VOUT=5V 1MHz VBIAS SPKIP
VIN=13.5V VOUT=5V 2MHz VBIAS SPKIP
VIN=13.5V VOUT=5V 2MHz NOVBIAS SPKIP
VIN=13.5V VOUT=5V 2MHz NOVBIAS NOSPKIP
VIN=13.5V VOUT=5V 2MHz VBIAS NOSPKIP
Figure 46. Efficiency curves over fsw: VIN = 13.5 V - VOUT = 5 V (log scale)
95
90
85
80
75
70
65
60
0.0015
56/66
0.015
0.15
VIN=13.5V VOUT=5V A6986 500kHz VBIAS NOPSKIP
VIN=13.5V VOUT=5V A6986 500kHz NOVBIAS NOPSKIP
VIN=13.5V VOUT=5V A6986 500kHz NOVBIAS PSKIP
VIN=13.5V VOUT=5V A6986 500kHz VBIAS PSKIP
VIN=13.5V VOUT=5V 1MHz VBIAS NOSPKIP
VIN=13.5V VOUT=5V 1MHz NOVBIAS NOSPKIP
VIN=13.5V VOUT=5V 1MHz NOVBIAS SPKIP
VIN=13.5V VOUT=5V 1MHz VBIAS SPKIP
VIN=13.5V VOUT=5V 2MHz VBIAS SPKIP
VIN=13.5V VOUT=5V 2MHz NOVBIAS SPKIP
VIN=13.5V VOUT=5V 2MHz NOVBIAS NOSPKIP
VIN=13.5V VOUT=5V 2MHz VBIAS NOSPKIP
DocID025376 Rev 5
2
L6986
Efficiency curves
Figure 47. Efficiency curves over fsw: VIN = 24 V - VOUT = 3.3 V
85
80
75
70
65
60
55
50
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
VIN=24V VOUT=3.3V A6986 500kHz VBIAS PSKIP
VIN=24V VOUT=3.3V A6986 500kHz NOVBIAS PSKIP
VIN=24V VOUT=3.3V A6986 500kHz NOVBIAS NOPSKIP
VIN=24V VOUT=3.3V A6986 500kHz VBIAS NOPSKIP
VIN=24V VOUT=3.3V 1MHz VBIAS PSKIP
VIN=24V VOUT=3.3V 1MHz NOVBIAS PSKIP
VIN=24V VOUT=3.3V 1MHz NOVBIAS NOPSKIP
VIN=24V VOUT=3.3V 1MHz VBIAS NOPSKIP
VIN=24V VOUT=3.3V 2MHz VBIAS NOSPKIP
VIN=24V VOUT=3.3V 2MHz NOVBIAS NOSPKIP
VIN=24V VOUT=3.3V 2MHz NOVBIAS SPKIP
VIN=24V VOUT=3.3V 2MHz VBIAS SPKIP
2
Figure 48. Efficiency curves over fsw: VIN = 24 V - VOUT = 3.3 V (log scale)
85
80
75
70
65
60
55
50
0.0025
0.025
0.25
VIN=24V VOUT=3.3V A6986 500kHz VBIAS PSKIP
VIN=24V VOUT=3.3V A6986 500kHz NOVBIAS PSKIP
VIN=24V VOUT=3.3V A6986 500kHz NOVBIAS NOPSKIP
VIN=24V VOUT=3.3V A6986 500kHz VBIAS NOPSKIP
VIN=24V VOUT=3.3V 1MHz VBIAS PSKIP
VIN=24V VOUT=3.3V 1MHz NOVBIAS PSKIP
VIN=24V VOUT=3.3V 1MHz NOVBIAS NOPSKIP
VIN=24V VOUT=3.3V 1MHz VBIAS NOPSKIP
VIN=24V VOUT=3.3V 2MHz VBIAS NOSPKIP
VIN=24V VOUT=3.3V 2MHz NOVBIAS NOSPKIP
VIN=24V VOUT=3.3V 2MHz NOVBIAS SPKIP
VIN=24V VOUT=3.3V 2MHz VBIAS SPKIP
DocID025376 Rev 5
57/66
66
Efficiency curves
L6986
Figure 49. Efficiency curves over fsw: VIN = 24 V - VOUT = 5 V
90
85
80
75
70
65
60
55
50
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
VIN=24V VOUT=5V A6986 500kHz VBIAS NOPSKIP
VIN=24V VOUT=5V A6986 500kHz NOVBIAS NOPSKIP
VIN=24V VOUT=5V A6986 500kHz NOVBIAS PSKIP
VIN=24V VOUT=5V A6986 500kHz VBIAS PSKIP
VIN=24V VOUT=5V 1MHz VBIAS NOSPKIP
VIN=24V VOUT=5V 1MHz NOVBIAS NOSPKIP
VIN=24V VOUT=5V 1MHz NOVBIAS SPKIP
VIN=24V VOUT=5V 1MHz VBIAS SPKIP
VIN=24V VOUT=5V 2MHz VBIAS SPKIP
VIN=24V VOUT=5V 2MHz NOVBIAS SPKIP
VIN=24V VOUT=5V 2MHz NOVBIAS NOSPKIP
VIN=24V VOUT=5V 2MHz VBIAS NOSPKIP
Figure 50. Efficiency curves over fsw: VIN = 24 V - VOUT = 5 V (log scale)
90
85
80
75
70
65
60
55
50
0.0025
58/66
0.025
0.25
VIN=24V VOUT=5V A6986 500kHz VBIAS NOPSKIP
VIN=24V VOUT=5V A6986 500kHz NOVBIAS NOPSKIP
VIN=24V VOUT=5V A6986 500kHz NOVBIAS PSKIP
VIN=24V VOUT=5V A6986 500kHz VBIAS PSKIP
VIN=24V VOUT=5V 1MHz VBIAS NOSPKIP
VIN=24V VOUT=5V 1MHz NOVBIAS NOSPKIP
VIN=24V VOUT=5V 1MHz NOVBIAS SPKIP
VIN=24V VOUT=5V 1MHz VBIAS SPKIP
VIN=24V VOUT=5V 2MHz VBIAS SPKIP
VIN=24V VOUT=5V 2MHz NOVBIAS SPKIP
VIN=24V VOUT=5V 2MHz NOVBIAS NOSPKIP
VIN=24V VOUT=5V 2MHz VBIAS NOSPKIP
DocID025376 Rev 5
2
L6986
Efficiency curves
Figure 51. Efficiency curves: fsw = 500kHz - VIN = 24 V - VOUT = 3.3 V
95
90
85
80
75
VIN=13.5V VOUT=3.3V A6986 500kHz VBIAS PSKIP
VIN=13.5V VOUT=3.3V A6986 500kHz NOVBIAS PSKIP
70
VIN=13.5V VOUT=3.3V A6986 500kHz NOVBIAS NOPSKIP
65
VIN=13.5V VOUT=3.3V A6986 500kHz VBIAS NOPSKIP
60
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
Figure 52. Efficiency curves: fsw = 500 kHz - VIN = 13.5 V - VOUT = 3.3 V (log scale)
90
80
70
60
VIN=13.5V VOUT=3.3V A6986 500kHz VBIAS PSKIP
VIN=13.5V VOUT=3.3V A6986 500kHz NOVBIAS PSKIP
50
VIN=13.5V VOUT=3.3V A6986 500kHz NOVBIAS NOPSKIP
VIN=13.5V VOUT=3.3V A6986 500kHz VBIAS NOPSKIP
40
30
0.001
0.01
0.1
Figure 53. Efficiency curves: fsw = 500 kHz - VIN = 13.5 V - VOUT = 5 V
95
90
85
80
75
70
VIN=13.5V VOUT=5V A6986 500kHz VBIAS NOPSKIP
65
VIN=13.5V VOUT=5V A6986 500kHz NOVBIAS NOPSKIP
VIN=13.5V VOUT=5V A6986 500kHz NOVBIAS PSKIP
60
VIN=13.5V VOUT=5V A6986 500kHz VBIAS PSKIP
55
0
0.2
0.4
0.6
0.8
DocID025376 Rev 5
1
1.2
1.4
1.6
59/66
66
Efficiency curves
L6986
Figure 54. Efficiency curves: fsw = 500 kHz - VIN = 13.5 V - VOUT = 5 V (log scale)
90
80
70
60
VIN=13.5V VOUT=5V A6986 500kHz VBIAS NOPSKIP
50
VIN=13.5V VOUT=5V A6986 500kHz NOVBIAS NOPSKIP
VIN=13.5V VOUT=5V A6986 500kHz NOVBIAS PSKIP
40
VIN=13.5V VOUT=5V A6986 500kHz VBIAS PSKIP
30
20
0.001
0.01
0.1
Figure 55. Efficiency curves: fsw = 500 kHz - VIN = 24 V - VOUT = 3.3 V
90
85
80
75
70
VIN=24V VOUT=3.3V A6986 500kHz VBIAS PSKIP
65
VIN=24V VOUT=3.3V A6986 500kHz NOVBIAS PSKIP
60
VIN=24V VOUT=3.3V A6986 500kHz NOVBIAS NOPSKIP
55
VIN=24V VOUT=3.3V A6986 500kHz VBIAS NOPSKIP
50
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
Figure 56. Efficiency curves: fsw = 500 kHz - VIN = 24 V - VOUT = 3.3 V (log scale)
80
70
60
50
VIN=24V VOUT=3.3V A6986 500kHz VBIAS PSKIP
40
30
20
0.001
60/66
VIN=24V VOUT=3.3V A6986 500kHz NOVBIAS PSKIP
VIN=24V VOUT=3.3V A6986 500kHz NOVBIAS NOPSKIP
VIN=24V VOUT=3.3V A6986 500kHz VBIAS NOPSKIP
0.01
DocID025376 Rev 5
0.1
2
L6986
Efficiency curves
Figure 57. Efficiency curves: fsw = 500 kHz - VIN = 24 V - VOUT = 5 V (log scale)
90
85
80
75
70
65
60
VIN=24V VOUT=5V A6986 500kHz VBIAS NOPSKIP
55
VIN=24V VOUT=5V A6986 500kHz NOVBIAS NOPSKIP
VIN=24V VOUT=5V A6986 500kHz NOVBIAS PSKIP
50
VIN=24V VOUT=5V A6986 500kHz VBIAS PSKIP
45
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
Figure 58. Efficiency curves: fsw = 500 kHz - VIN = 24 V - VOUT = 5 V (log scale)
90
80
70
60
50
40
VIN=13.5V VOUT=5V A6986 500kHz VBIAS NOPSKIP
VIN=13.5V VOUT=5V A6986 500kHz NOVBIAS NOPSKIP
VIN=13.5V VOUT=5V A6986 500kHz NOVBIAS PSKIP
VIN=13.5V VOUT=5V A6986 500kHz VBIAS PSKIP
30
20
0.001
0.01
0.1
DocID025376 Rev 5
61/66
66
Package information
9
L6986
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK is an ST trademark.
62/66
DocID025376 Rev 5
L6986
Package information
Figure 59. HTSSOP16 package outline
.
Table 14. HTSSOP16 package mechanical data
Dimensions (mm)
Symbol
Min.
Typ.
Max.
A
1.20
A1
0.15
A2
0.80
b
0.19
0.30
c
0.09
0.20
D
4.90
5.00
5.10
D1
2.8
3
3.2
E
6.20
6.40
6.60
E1
4.30
4.40
4.50
E2
2.8
3
3.2
e
L
1.05
0.65
0.45
L1
k
1.00
0.60
0.75
1.00
0.00
aaa
8.00
0.10
DocID025376 Rev 5
63/66
66
Order codes
10
L6986
Order codes
Table 15. Order codes
Part numbers
L6986
L6986TR
64/66
Package
HTSSOP16
DocID025376 Rev 5
Packaging
Tube
Tape and reel
L6986
11
Revision history
Revision history
Table 16. Document revision history
Date
Revision
11-Oct-2013
1
Initial release.
17-Mar-2014
2
Several modifications throughout document.
3
Updated Section 3: Electrical characteristics (added sentence about testing above
Table 7 on page 11).
Updated Section 6.5: Synchronization (LNM) on page 43 (added “(LNM)” to title, updated
3 first paragraphs, updated second paragraph below Figure 33 on page 44).
Updated cross-reference in Section 6.6.2: Inductor selection on page 49.
Added Section 10: Order codes on page 64.
Minor modifications throughout document.
4
Updated Section : Features on page 1 (replaced 5 by 8 A IQ-SHTDWN).
Updated Equation 17 on page 29, Equation 18 on page 33, Equation 20 on page 34,
Equation 34 on page 39, Equation 44 on page 48, Equation 47 on page 48 to Equation 49
on page 48, Equation 51 on page 49 to Equation 54 on page 50.
Updated Section 5.1: GCO(s) control to output transfer function on page 33 (replaced “R0”
by “RLOAD” and “LC filter” by “power stage”).
Updated Figure 24 on page 33, Figure 25 on page 35, and Figure 31 on page 43.
Added Section 8: Efficiency curves on page 55.
03-Apr-2014
22-Aug-2014
23-Feb-2015
Changes
Updated Section : Features on page 1 (replaced 110 m by 150 m- RDSON LS).
Updated Section 4.3: Soft-start and inhibit on page 14 (added and updated text, added
Figure 7 to Figure 9, Equation 2 to Equation 11).
Updated Section 6.5: Synchronization (LNM) on page 43 (added and
updated text, Figure 31, added Figure 34 to Figure 37, Table 9).
Minor modifications throughout document.
DocID025376 Rev 5
65/66
66
L6986
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2015 STMicroelectronics – All rights reserved
66/66
DocID025376 Rev 5