Technical Data Sheet

LD1117
Adjustable and fixed low drop positive voltage regulator
Datasheet - production data
flows mostly into the load. Only a very common
10 µF minimum capacitor is needed for stability.
On chip trimming allows the regulator to reach a
very tight output voltage tolerance, within ± 1 % at
25 °C. The adjustable LD1117 is pin to pin
compatible with the other standard. Adjustable
voltage regulators maintaining the better
performances in terms of drop and tolerance.
DPAK
TO-220
SOT-223
SO-8
Features
• Low dropout voltage (1 V typ.)
• 2.85 V device performances are suitable for
SCSI-2 active termination
• Output current up to 800 mA
• Fixed output voltage of: 1.2 V, 1.8 V, 2.5 V,
3.3 V, 5.0 V
• Adjustable version availability (VREF = 1.25 V)
• Internal current and thermal limit
• Available in ± 1 % (at 25 °C) and 2 % in full
temperature range
• Supply voltage rejection: 75 dB (typ.)
Description
The LD1117 is a low drop voltage regulator able
to provide up to 800 mA of output current,
available even in adjustable version (VREF =
1.25 V). Concerning fixed versions, are offered
the following output voltages: 1.2 V, 1.8 V, 2.5 V,
2.85 V, 3.3 V and 5.0 V. The device is supplied in:
SOT-223, DPAK, SO-8 and TO-220. The SOT223 and DPAK surface mount packages optimize
the thermal characteristics even offering a
relevant space saving effect. High efficiency is
assured by NPN pass transistor. In fact in this
case, unlike than PNP one, the quiescent current
November 2013
This is information on a product in full production.
DocID2572 Rev 33
1/44
www.st.com
44
Contents
LD1117
Contents
1
Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2
Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4
Schematic application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6
Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7
LD1117 adjustable: application note . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
8
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
9
Packing mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
10
Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
11
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
2/44
DocID2572 Rev 33
LD1117
List of tables
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Table 17.
Table 18.
Table 19.
Table 20.
Table 21.
Table 22.
Table 23.
Table 24.
Table 25.
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Electrical characteristics of LD1117#12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Electrical characteristics of LD1117#18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Electrical characteristics of LD1117#25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Electrical characteristics of LD1117#33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Electrical characteristics of LD1117#50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Electrical characteristics of LD1117 (adjustable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Electrical characteristics of LD1117#12C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Electrical characteristics of LD1117#18C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Electrical characteristics of LD1117#25C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Electrical characteristics of LD1117#33C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Electrical characteristics of LD1117#50C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Electrical characteristics of LD1117C (adjustable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
TO-220 mechanical data (type STD-ST Dual Gauge) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
TO-220 mechanical data (type STD-ST Single Gauge) . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
SOT-223 mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
SO-8 mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
DPAK mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Footprint data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
SOT-223 tape and reel mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
SO-8 tape and reel mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
DPAK tape and reel mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
DocID2572 Rev 33
3/44
List of figures
LD1117
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
Figure 19.
Figure 20.
Figure 21.
Figure 22.
Figure 23.
Figure 24.
Figure 25.
Figure 26.
Figure 27.
4/44
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pin connections (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Application circuit (for 1.2 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Application circuit (for other fixed output voltages) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Negative supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Circuit for increasing output voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Voltage regulator with reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Battery backed-up regulated supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Post-regulated dual supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Adjustable output voltage application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Adjustable output voltage application with improved ripple rejection . . . . . . . . . . . . . . . . . 24
Drawing dimension TO-220 (type STD-ST Dual Gauge) . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Drawing dimension TO-220 (type STD-ST Single Gauge) . . . . . . . . . . . . . . . . . . . . . . . . . 28
Drawing dimension SOT-223 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Drawing dimension SO-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Drawing dimension DPAK (type STD-ST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Drawing dimension DPAK (type Fujitsu-subcon.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Drawing dimension DPAK (type IDS-subcon.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
DPAK footprint recommended data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Drawing dimension tube for TO-220 Dual Gauge (mm.) . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Drawing dimension tube for TO-220 Single Gauge (mm.) . . . . . . . . . . . . . . . . . . . . . . . . . 36
Tape for SOT-223 (dimensions are in mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Reel for STO-223 (dimensions are in mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
SO-8 tape and reel dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
DPAK footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Tape for DPAK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Reel for DPAK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
DocID2572 Rev 33
LD1117
1
Diagram
Diagram
Figure 1. Block diagram
DocID2572 Rev 33
5/44
Pin configuration
2
LD1117
Pin configuration
Figure 2. Pin connections (top view)
SO-8
SOT-223
TO-220
DPAK
Note:
6/44
The TAB is connected to the VOUT.
DocID2572 Rev 33
LD1117
Maximum ratings
3
Maximum ratings
Table 1. Absolute maximum ratings
Symbol
Value
Unit
DC input voltage
15
V
PTOT
Power dissipation
12
W
TSTG
Storage temperature range
-40 to +150
°C
-40 to +125
°C
TOP
Operating junction temperature range
0 to +125
°C
VIN
(1)
Parameter
for C version
for standard version
1. Absolute maximum rating of VIN = 18 V, when IOUT is lower than 20 mA.
Table 2. Thermal data
Symbol
Parameter
SOT-223
SO-8
DPAK
TO-220
Unit
RthJC
Thermal resistance junction-case
15
20
8
5
°C/W
RthJA
Thermal resistance junction-ambient
110
55
100
50
°C/W
DocID2572 Rev 33
7/44
Schematic application
4
LD1117
Schematic application
Figure 3. Application circuit (for 1.2 V)
Figure 4. Application circuit (for other fixed output voltages)
8/44
DocID2572 Rev 33
LD1117
5
Electrical characteristics
Electrical characteristics
Refer to the test circuits, TJ = 0 to 125 °C, CO = 10 µF, R = 120 Ω between GND and OUT
pins, unless otherwise specified.
Table 3. Electrical characteristics of LD1117#12
Symbol
Parameter
Test condition
Min.
Typ.
Max.
Unit
VO
Output voltage
Vin = 3.2 V, IO = 10 mA, TJ = 25 °C
1.188
1.20
1.212
V
VO
Output voltage
IO = 10 to 800 mA
Vin - VO = 1.4 to 10 V
1.140
1.20
1.260
V
ΔVO
Line regulation
Vin - VO = 1.5 to 13.75 V, IO = 10 mA
0.035
0.2
%
ΔVO
Load regulation
Vin - VO = 3 V, IO = 10 to 800 mA
0.1
0.4
%
ΔVO
Temperature stability
ΔVO
Long term stability
1000 hrs, TJ = 125 °C
Vin
Operating input voltage
Iadj
Adjustment pin current
Vin ≤ 15 V
Adjustment pin current change
0.5
%
0.3
%
15
V
60
120
µA
Vin - VO = 1.4 to 10 V
IO = 10 to 800 mA
1
5
µA
Minimum load current
Vin = 15 V
2
5
mA
IO
Output current
Vin - VO = 5 V, TJ = 25 °C
950
1300
mA
eN
Output noise (%VO)
B = 10 Hz to 10 kHz, TJ = 25 °C
Supply voltage rejection
IO = 40 mA, f = 120 Hz, TJ = 25 °C
Vin - VO = 3 V, Vripple = 1 VPP
ΔIadj
IO(min)
SVR
Vd
Dropout voltage
Thermal regulation
800
60
0.003
%
75
dB
IO = 100 mA
1
1.1
IO = 500 mA
1.05
1.15
IO = 800 mA
1.10
1.2
Ta = 25 °C, 30 ms Pulse
0.01
0.1
DocID2572 Rev 33
V
%/W
9/44
Electrical characteristics
LD1117
Refer to the test circuits, TJ = 0 to 125 °C, CO = 10 µF, unless otherwise specified.
Table 4. Electrical characteristics of LD1117#18
Symbol
Parameter
Test condition
Min.
Typ.
Max.
Unit
1.8
1.82
V
1.84
V
VO
Output voltage
Vin = 3.8 V, IO = 10 mA, TJ = 25 °C
1.78
VO
Output voltage
IO = 0 to 800 mA, Vin = 3.3 to 8 V
1.76
ΔVO
Line regulation
Vin = 3.3 to 8 V, IO = 0 mA
1
6
mV
ΔVO
Load regulation
Vin = 3.3 V, IO = 0 to 800 mA
1
10
mV
ΔVO
Temperature stability
ΔVO
Long term stability
1000 hrs, TJ = 125 °C
Vin
Operating input voltage
IO = 100 mA
Id
Quiescent current
Vin ≤ 8 V
IO
Output current
Vin = 6.8 V, TJ = 25 °C
eN
Output noise voltage
B = 10 Hz to 10 kHz, TJ = 25 °C
Supply voltage rejection
IO = 40 mA, f = 120 Hz, TJ = 25 °C
Vin = 5.5 V, Vripple = 1 VPP
SVR
Vd
Dropout voltage
Thermal regulation
10/44
800
60
0.5
%
0.3
%
15
V
5
10
mA
950
1300
mA
100
µV
75
dB
IO = 100 mA
1
1.1
IO = 500 mA
1.05
1.15
IO = 800 mA
1.10
1.2
Ta = 25 °C, 30 ms Pulse
0.01
0.1
DocID2572 Rev 33
V
%/W
LD1117
Electrical characteristics
Refer to the test circuits, TJ = 0 to 125 °C, CO = 10 µF, unless otherwise specified.
Table 5. Electrical characteristics of LD1117#25
Symbol
Parameter
Test condition
Min.
Typ.
Max.
Unit
2.5
2.525
V
2.55
V
VO
Output voltage
Vin = 4.5 V, IO = 10 mA, TJ = 25 °C
2.475
VO
Output voltage
IO = 0 to 800 mA, Vin = 3.9 to 10 V
2.45
ΔVO
Line regulation
Vin = 3.9 to 10 V, IO = 0 mA
1
6
mV
ΔVO
Load regulation
Vin = 3.9 V, IO = 0 to 800 mA
1
10
mV
ΔVO
Temperature stability
ΔVO
Long term stability
1000 hrs, TJ = 125 °C
Vin
Operating input voltage
IO = 100 mA
Id
Quiescent current
Vin ≤ 10 V
IO
Output current
Vin = 7.5 V TJ = 25 °C
eN
Output noise voltage
B = 10 Hz to 10 kHz, TJ = 25 °C
Supply voltage rejection
IO = 40 mA, f = 120 Hz, TJ = 25 °C
Vin = 5.5 V, Vripple = 1 VPP
SVR
Vd
Dropout voltage
Thermal regulation
800
60
0.5
%
0.3
%
15
V
5
10
mA
950
1300
mA
100
µV
75
dB
IO = 100 mA
1
1.1
IO = 500 mA
1.05
1.15
IO = 800 mA
1.10
1.2
Ta = 25 °C, 30 ms Pulse
0.01
0.1
DocID2572 Rev 33
V
%/W
11/44
Electrical characteristics
LD1117
Refer to the test circuits, TJ = 0 to 125 °C, CO = 10 µF, unless otherwise specified.
Table 6. Electrical characteristics of LD1117#33
Symbol
Parameter
Test condition
Min.
Typ.
Max.
Unit
3.3
3.333
V
3.365
V
VO
Output voltage
Vin = 5.3 V, IO = 10 mA, TJ = 25 °C
3.267
VO
Output voltage
IO = 0 to 800 mA, Vin = 4.75 to 10 V
3.235
ΔVO
Line regulation
Vin = 4.75 to 15 V, IO = 0 mA
1
6
mV
ΔVO
Load regulation
Vin = 4.75 V, IO = 0 to 800 mA
1
10
mV
ΔVO
Temperature stability
ΔVO
Long term stability
1000 hrs, TJ = 125 °C
Vin
Operating input voltage
IO = 100 mA
Id
Quiescent current
Vin ≤ 15 V
IO
Output current
Vin = 8.3 V, TJ = 25 °C
eN
Output noise voltage
B = 10 Hz to 10 kHz, TJ = 25 °C
Supply voltage rejection
IO = 40 mA, f = 120 Hz, TJ = 25 °C
Vin = 6.3 V, Vripple = 1 VPP
SVR
Vd
Dropout voltage
Thermal regulation
12/44
800
60
0.5
%
0.3
%
15
V
5
10
mA
950
1300
mA
100
µV
75
dB
IO = 100 mA
1
1.1
IO = 500 mA
1.05
1.15
IO = 800 mA
1.10
1.2
Ta = 25 °C, 30 ms Pulse
0.01
0.1
DocID2572 Rev 33
V
%/W
LD1117
Electrical characteristics
Refer to the test circuits, TJ = 0 to 125 °C, CO = 10 µF, unless otherwise specified.
Table 7. Electrical characteristics of LD1117#50
Symbol
Parameter
Test condition
Min.
Typ.
Max.
Unit
5
5.05
V
5.1
V
VO
Output voltage
Vin = 7 V, IO = 10 mA, TJ = 25 °C
4.95
VO
Output voltage
IO = 0 to 800 mA, Vin = 6.5 to 15 V
4.9
ΔVO
Line regulation
Vin = 6.5 to 15 V, IO = 0 mA
1
10
mV
ΔVO
Load regulation
Vin = 6.5 V, IO = 0 to 800 mA
1
15
mV
ΔVO
Temperature stability
ΔVO
Long term stability
1000 hrs, TJ = 125 °C
Vin
Operating input voltage
IO = 100 mA
Id
Quiescent current
Vin ≤ 15 V
IO
Output current
Vin = 10 V, TJ = 25 °C
eN
Output noise voltage
B = 10 Hz to 10 kHz, TJ = 25 °C
Supply voltage rejection
IO = 40 mA, f = 120 Hz, TJ = 25 °C
Vin = 8 V, Vripple = 1 VPP
SVR
Vd
Dropout voltage
Thermal regulation
800
60
0.5
%
0.3
%
15
V
5
10
mA
950
1300
mA
100
µV
75
dB
IO = 100 mA
1
1.1
IO = 500 mA
1.05
1.15
IO = 800 mA
1.10
1.2
Ta = 25 °C, 30 ms Pulse
0.01
0.1
DocID2572 Rev 33
V
%/W
13/44
Electrical characteristics
LD1117
Refer to the test circuits, TJ = 0 to 125 °C, CO = 10 µF, unless otherwise specified.
Table 8. Electrical characteristics of LD1117 (adjustable)
Symbol
Parameter
Test condition
Min.
Typ.
Max.
Unit
1.238
1.25
1.262
V
1.275
V
0.035
0.2
%
0.1
0.4
%
Vref
Reference voltage
Vin - VO = 2 V, IO = 10 mA, TJ = 25 °C
Vref
Reference voltage
IO = 10 to 800 mA, Vin - VO = 1.4 to 10 V 1.225
ΔVO
Line regulation
Vin - VO = 1.5 to 13.75 V, IO = 10 mA
ΔVO
Load regulation
Vin - VO = 3 V, IO = 10 to 800 mA
ΔVO
Temperature stability
ΔVO
Long term stability
Vin
Operating input voltage
Iadj
Adjustment pin current
1000 hrs, TJ = 125 °C
0.5
%
0.3
%
15
V
60
120
µA
Adjustment pin current change Vin - VO = 1.4 to 10 V, IO = 10 to 800 mA
1
5
µA
Minimum load current
Vin = 15 V
2
5
mA
IO
Output current
Vin - VO = 5 V, TJ = 25 °C
950
1300
mA
eN
Output noise (%VO)
B = 10 Hz to 10 kHz, TJ = 25 °C
Supply voltage rejection
IO = 40 mA, f = 120 Hz, TJ = 25 °C
Vin - VO = 3 V, Vripple = 1 VPP
ΔIadj
IO(min)
SVR
Vd
Dropout voltage
Thermal regulation
14/44
Vin ≤ 15 V
800
60
0.003
%
75
dB
IO = 100 mA
1
1.1
IO = 500 mA
1.05
1.15
IO = 800 mA
1.10
1.2
Ta = 25 °C, 30 ms Pulse
0.01
0.1
DocID2572 Rev 33
V
%/W
LD1117
Electrical characteristics
Refer to the test circuits, TJ = -40 to 125 °C, CO = 10 µF, R = 120 Ω between GND and OUT
pins, unless otherwise specified.
Table 9. Electrical characteristics of LD1117#12C
Symbol
Parameter
Test condition
Min.
Typ.
Max.
Unit
VO
Output voltage
Vin - VO = 2 V, IO = 10 mA, TJ = 25 °C
1.176
1.20
1.224
V
VO
Output voltage
IO = 10 to 800 mA, Vin - VO = 1.4 to 10 V
1.120
1.20
1.280
V
ΔVO
Line regulation
Vin - VO = 1.5 to 13.75 V, IO = 10 mA
1
%
ΔVO
Load regulation
Vin - VO = 3 V, IO = 10 to 800 mA
1
%
ΔVO
Temperature stability
ΔVO
Long term stability
1000 hrs, TJ = 125 °C
Vin
Operating input voltage
Iadj
Adjustment pin current
Vin ≤ 15 V
ΔIadj
Adjustment pin current
change
IO(min)
0.5
%
0.3
%
15
V
60
120
µA
Vin - VO = 1.4 to 10 V
IO = 10 to 800 mA
1
5
µA
Minimum load current
Vin = 15 V
2
5
mA
IO
Output current
Vin - VO = 5 V, TJ = 25 °C
950
1300
mA
eN
Output noise (%VO)
B = 10 Hz to 10 kHz, TJ = 25 °C
Supply voltage rejection
IO = 40 mA, f = 120 Hz, TJ = 25 °C
Vin - VO = 3 V, Vripple = 1 VPP
SVR
Vd
Dropout voltage
Thermal regulation
800
60
0.003
%
75
dB
IO = 100 mA, TJ = 0 to 125 °C
1
1.1
IO = 500 mA, TJ = 0 to 125 °C
1.05
1.2
IO = 800 mA, TJ = 0 to 125 °C
1.10
1.3
Ta = 25 °C, 30 ms Pulse
0.01
0.1
DocID2572 Rev 33
V
%/W
15/44
Electrical characteristics
LD1117
Refer to the test circuits, TJ = -40 to 125 °C, CO = 10 µF, unless otherwise specified.
Table 10. Electrical characteristics of LD1117#18C
Symbol
Parameter
Test condition
Min.
Typ.
Max.
Unit
1.8
1.84
V
1.87
V
VO
Output voltage
Vin = 3.8 V, IO = 10 mA, TJ = 25 °C
1.76
VO
Output voltage
IO = 0 to 800 mA, Vin = 3.9 to 10 V
1.73
ΔVO
Line regulation
Vin = 3.3 to 8 V, IO = 0 mA
1
30
mV
ΔVO
Load regulation
Vin = 3.3 V, IO = 0 to 800 mA
1
30
mV
ΔVO
Temperature stability
ΔVO
Long term stability
1000 hrs, TJ = 125 °C
Vin
Operating input voltage
IO = 100 mA
Id
Quiescent current
Vin ≤ 8 V
IO
Output current
Vin = 6.8 V TJ = 25 °C
eN
Output noise voltage
B = 10 Hz to 10 kHz, TJ = 25 °C
Supply voltage rejection
IO = 40 mA, f = 120 Hz, TJ = 25 °C
Vin = 5.5 V, Vripple = 1 VPP
SVR
Vd
Vd
Dropout voltage
Dropout voltage
Thermal regulation
16/44
800
60
0.5
%
0.3
%
15
V
5
10
mA
950
1300
mA
100
µV
75
dB
IO = 100 mA, TJ = 0 to 125 °C
1
1.1
IO = 500 mA, TJ = 0 to 125 °C
1.05
1.15
IO = 800 mA, TJ = 0 to 125 °C
1.10
1.2
IO = 100 mA
1.1
IO = 500 mA
1.2
IO = 800 mA
1.3
Ta = 25 °C, 30 ms Pulse
DocID2572 Rev 33
0.01
0.1
V
V
%/W
LD1117
Electrical characteristics
Refer to the test circuits, TJ = -40 to 125 °C, CO = 10 µF, unless otherwise specified.
Table 11. Electrical characteristics of LD1117#25C
Symbol
Parameter
Test condition
Min.
Typ.
Max.
Unit
2.5
2.55
V
2.6
V
VO
Output voltage
Vin = 4.5 V, IO = 10 mA, TJ = 25 °C
2.45
VO
Output voltage
IO = 0 to 800 mA, Vin = 3.9 to 10 V
2.4
ΔVO
Line regulation
Vin = 3.9 to 10 V, IO = 0 mA
1
30
mV
ΔVO
Load regulation
Vin = 3.9 V, IO = 0 to 800 mA
1
30
mV
ΔVO
Temperature stability
ΔVO
Long term stability
1000 hrs, TJ = 125 °C
Vin
Operating input voltage
IO = 100 mA
Id
Quiescent current
Vin ≤ 10 V
IO
Output current
Vin = 7.5 V TJ = 25 °C
eN
Output noise voltage
B = 10 Hz to 10 kHz, TJ = 25 °C
Supply voltage rejection
IO = 40 mA, f = 120 Hz, TJ = 25 °C
Vin = 5.5 V, Vripple = 1 VPP
SVR
Vd
Vd
Dropout voltage
Dropout voltage
Thermal regulation
800
60
0.5
%
0.3
%
15
V
5
10
mA
950
1300
mA
100
µV
75
dB
IO = 100 mA, TJ = 0 to 125 °C
1
1.1
IO = 500 mA, TJ = 0 to 125 °C
1.05
1.15
IO = 800 mA, TJ = 0 to 125 °C
1.10
1.2
IO = 100 mA
1.1
IO = 500 mA
1.2
IO = 800 mA
1.3
Ta = 25 °C, 30 ms Pulse
DocID2572 Rev 33
0.01
0.1
V
V
%/W
17/44
Electrical characteristics
LD1117
Refer to the test circuits, TJ = -40 to 125 °C, CO = 10 µF, unless otherwise specified.
Table 12. Electrical characteristics of LD1117#33C
Symbol
Parameter
Test condition
Min.
Typ.
Max.
Unit
3.3
3.36
V
3.44
V
VO
Output voltage
Vin = 5.3 V, IO = 10 mA, TJ = 25 °C
3.24
VO
Output voltage
IO = 0 to 800 mA, Vin = 4.75 to 10 V
3.16
ΔVO
Line regulation
Vin = 4.75 to 15 V, IO = 0 mA
1
30
mV
ΔVO
Load regulation
Vin = 4.75 V, IO = 0 to 800 mA
1
30
mV
ΔVO
Temperature stability
ΔVO
Long term stability
1000 hrs, TJ = 125 °C
Vin
Operating input voltage
IO = 100 mA
Id
Quiescent current
Vin ≤ 15 V
IO
Output current
Vin = 8.3 V, TJ = 25 °C
eN
Output noise voltage
B = 10 Hz to 10 kHz, TJ = 25 °C
Supply voltage rejection
IO = 40 mA, f = 120 Hz, TJ = 25 °C
Vin = 6.3 V, Vripple = 1 VPP
SVR
Vd
Vd
Dropout voltage
Dropout voltage
Thermal regulation
18/44
800
60
0.5
%
0.3
%
15
V
5
10
mA
950
1300
mA
100
µV
75
dB
IO = 100 mA, TJ = 0 to 125 °C
1
1.1
IO = 500 mA, TJ = 0 to 125 °C
1.05
1.15
IO = 800 mA, TJ = 0 to 125 °C
1.10
1.2
IO = 100 mA
1.1
IO = 500 mA
1.2
IO = 800 mA
1.3
Ta = 25 °C, 30 ms Pulse
DocID2572 Rev 33
0.01
0.1
V
V
%/W
LD1117
Electrical characteristics
Refer to the test circuits, TJ = -40 to 125 °C, CO = 10 µF, unless otherwise specified.
Table 13. Electrical characteristics of LD1117#50C
Symbol
Parameter
Test condition
Min.
Typ.
Max.
Unit
5
5.1
V
5.2
V
VO
Output voltage
Vin = 7 V, IO = 10 mA, TJ = 25 °C
4.9
VO
Output voltage
IO = 0 to 800 mA, Vin = 6.5 to 15 V
4.8
ΔVO
Line regulation
Vin = 6.5 to 15 V, IO = 0 mA
1
50
mV
ΔVO
Load regulation
Vin = 6.5 V, IO = 0 to 800 mA
1
50
mV
ΔVO
Temperature stability
ΔVO
Long term stability
1000 hrs, TJ = 125 °C
Vin
Operating input voltage
IO = 100 mA
Id
Quiescent current
Vin ≤ 15 V
IO
Output current
Vin = 10 V, TJ = 25 °C
eN
Output noise voltage
B = 10 Hz to 10 kHz, TJ = 25 °C
Supply voltage rejection
IO = 40 mA, f = 120 Hz, TJ = 25 °C
Vin = 8 V, Vripple = 1 VPP
SVR
Vd
Vd
Dropout voltage
Dropout voltage
Thermal regulation
800
60
0.5
%
0.3
%
15
V
5
10
mA
950
1300
mA
100
µV
75
dB
IO = 100 mA, TJ = 0 to 125 °C
1
1.1
IO = 500 mA, TJ = 0 to 125 °C
1.05
1.15
IO = 800 mA, TJ = 0 to 125 °C
1.10
1.2
IO = 100 mA
1.1
IO = 500 mA
1.2
IO = 800 mA
1.3
Ta = 25 °C, 30 ms Pulse
DocID2572 Rev 33
0.01
0.1
V
V
%/W
19/44
Electrical characteristics
LD1117
Refer to the test circuits, TJ = -40 to 125 °C, CO = 10 µF, unless otherwise specified.
Table 14. Electrical characteristics of LD1117C (adjustable)
Symbol
Parameter
Test condition
Min.
Typ.
Max.
Unit
1.225
1.25
1.275
V
1.3
V
Vref
Reference voltage
Vin - VO = 2 V, IO = 10 mA, TJ = 25 °C
Vref
Reference voltage
IO = 10 to 800 mA, Vin - VO= 1.4 to 10 V
ΔVO
Line regulation
Vin - VO = 1.5 to 13.75 V, IO = 10 mA
1
%
ΔVO
Load regulation
Vin - VO = 3 V, IO = 10 to 800 mA
1
%
ΔVO
Temperature stability
ΔVO
Long term stability
Vin
Operating input voltage
Iadj
Adjustment pin current
1.2
1000 hrs, TJ = 125 °C
0.5
%
0.3
%
15
V
60
120
µA
Adjustment pin current change Vin - VO = 1.4 to 10 V, IO = 10 to 800 mA
1
10
µA
Minimum load current
Vin = 15 V
2
5
mA
IO
Output current
Vin - VO = 5 V, TJ = 25 °C
950
1300
mA
eN
Output noise (%VO)
B = 10 Hz to 10 kHz, TJ = 25 °C
Supply voltage rejection
IO = 40 mA, f = 120 Hz, TJ = 25 °C
Vin - VO = 3 V, Vripple = 1 VPP
ΔIadj
IO(min)
SVR
Vd
Vd
Dropout voltage
Dropout voltage
Thermal regulation
20/44
Vin ≤ 15 V
800
60
0.003
%
75
dB
IO = 100 mA, TJ = 0 to 125 °C
1
1.1
IO = 500 mA, TJ = 0 to 125 °C
1.05
1.15
IO = 800 mA, TJ = 0 to 125 °C
1.10
1.2
IO = 100 mA
1.1
IO = 500 mA
1.2
IO = 800 mA
1.3
Ta = 25 °C, 30 ms Pulse
DocID2572 Rev 33
0.01
0.1
V
V
%/W
LD1117
6
Typical application
Typical application
Figure 5. Negative supply
Figure 6. Circuit for increasing output voltage
Figure 7. Voltage regulator with reference
DocID2572 Rev 33
21/44
Typical application
LD1117
Figure 8. Battery backed-up regulated supply
22/44
DocID2572 Rev 33
LD1117
Typical application
Figure 9. Post-regulated dual supply
DocID2572 Rev 33
23/44
LD1117 adjustable: application note
7
LD1117
LD1117 adjustable: application note
The LD1117 adjustable has a thermal stabilized 1.25 ± 0.012 V reference voltage between
the OUT and ADJ pins. IADJ is 60 µA typ. (120 µA max.) and ΔIADJ is 1 µA typ. (5 µA max.).
R1 is normally fixed to 120 Ω. From Figure 9 we obtain:
VOUT = VREF + R2 (IADJ +IR1) = VREF + R2 (IADJ +VREF /R1) = VREF (1 + R2 / R1) + R2 x IADJ.
In normal application R2 value is in the range of few kΩ, so the R2 x IADJ product could not
be considered in the VOUT calculation; then the above expression becomes:
VOUT = VREF (1 + R2 / R1).
In order to have the better load regulation it is important to realize a good Kelvin connection
of R1 and R2 resistors. In particular R1 connection must be realized very close to OUT and
ADJ pin, while R2 ground connection must be placed as near as possible to the negative
Load pin. Ripple rejection can be improved by introducing a 10 µF electrolytic capacitor
placed in parallel to the R2 resistor (see Figure 10).
Figure 10. Adjustable output voltage application
Figure 11. Adjustable output voltage application with improved ripple rejection
24/44
DocID2572 Rev 33
LD1117
8
Package mechanical data
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
Table 15. TO-220 mechanical data (type STD-ST Dual Gauge)
mm
Dim.
Min.
Typ.
Max.
A
4.40
4.60
b
0.61
0.88
b1
1.14
1.70
c
0.48
0.70
D
15.25
15.75
D1
1.27
E
10
10.40
e
2.40
2.70
e1
4.95
5.15
F
1.23
1.32
H1
6.20
6.60
J1
2.40
2.72
L
13
14
L1
3.50
3.93
L20
16.40
L30
28.90
∅P
3.75
3.85
Q
2.65
2.95
DocID2572 Rev 33
25/44
Package mechanical data
LD1117
Figure 12. Drawing dimension TO-220 (type STD-ST Dual Gauge)
BW\SH$B5HYB7
26/44
DocID2572 Rev 33
LD1117
Package mechanical data
Table 16. TO-220 mechanical data (type STD-ST Single Gauge)
mm
Dim.
Min.
Typ.
Max.
A
4.40
4.60
b
0.61
0.88
b1
1.14
1.70
c
0.48
0.70
D
15.25
15.75
E
10
10.40
e
2.40
2.70
e1
4.95
5.15
F
0.51
0.60
H1
6.20
6.60
J1
2.40
2.72
L
13
14
L1
3.50
3.93
L20
16.40
L30
28.90
∅P
3.75
3.85
Q
2.65
2.95
DocID2572 Rev 33
27/44
Package mechanical data
LD1117
Figure 13. Drawing dimension TO-220 (type STD-ST Single Gauge)
BUHY'
28/44
DocID2572 Rev 33
LD1117
Package mechanical data
Table 17. SOT-223 mechanical data
mm
Dim.
Min.
Typ.
A
Max.
1.80
A1
0.02
0.1
B
0.60
0.70
0.85
B1
2.90
3.00
3.15
c
0.24
0.26
0.35
D
6.30
6.50
6.70
e
2.30
e1
4.60
E
3.30
3.50
3.70
H
6.70
7.00
7.30
V
10°
Figure 14. Drawing dimension SOT-223
0046067_M
DocID2572 Rev 33
29/44
Package mechanical data
LD1117
Table 18. SO-8 mechanical data
mm
Dim.
Min.
Typ.
A
Max.
1.75
A1
0.10
0.25
A2
1.25
b
0.28
0.48
c
0.17
0.23
D
4.80
4.90
5.00
E
5.80
6.00
6.20
E1
3.80
3.90
4.00
e
1.27
h
0.25
0.50
L
0.40
1.27
L1
k
1.04
0°
8°
ccc
0.10
Figure 15. Drawing dimension SO-8
0016023_Rev_G
30/44
DocID2572 Rev 33
LD1117
Package mechanical data
Table 19. DPAK mechanical data
Dim.
Min.
Type Fujitsu-subcon.
Type IDS-subcon
mm.
mm.
mm.
Typ.
Max.
Min.
Typ.
Max.
Min.
Typ.
Max.
2.30
2.35
2.19
2.38
A
2.20
2.40
2.25
A1
0.90
1.10
0.96
1.06
0.89
1.14
A2
0.03
0.23
0
0.10
0.03
0.23
b
0.64
0.90
0.76
0.86
0.64
0.88
b4
5.20
5.40
5.28
5.38
5.21
5.46
c
0.45
0.60
0.46
0.56
0.46
0.58
c2
0.48
0.60
0.46
0.56
0.46
0.58
D
6.00
6.20
6.05
6.15
5.97
6.22
5.27
5.47
D1
E
5.10
6.40
6.60
E1
4.70
e
2.28
2.23
4.40
4.60
H
9.35
10.10
L
1.00
L1
2.80
L2
0.80
0.60
R
V2
6.55
6.65
6.35
1.00
2.28
2.33
2.28
4.51
4.61
10.42
10.30
9.40
1.40
1.60
0.90
2.50
2.65
1.03
1.13
0.89
1.27
0.70
0.90
0.64
1.02
0.40
8°
6.73
4.70
9.90
0.20
0°
6.60
5.20
4.77
e1
L4
Note:
Type STD-ST
0°
0.20
8°
0°
8°
The DPAK package coming from the two subcontractors (Fujitsu and IDS) are fully
compatible with the ST's package suggested footprint.
DocID2572 Rev 33
31/44
Package mechanical data
LD1117
Figure 16. Drawing dimension DPAK (type STD-ST)
0068772/G
Note:
32/44
1
Maximum resin gate protrusion: 0.5 mm.
2
Maximum resin protrusion: 0.25 mm.
DocID2572 Rev 33
LD1117
Package mechanical data
Figure 17. Drawing dimension DPAK (type Fujitsu-subcon.)
0068772/G
DocID2572 Rev 33
33/44
Package mechanical data
LD1117
Figure 18. Drawing dimension DPAK (type IDS-subcon.)
0068772/G
34/44
DocID2572 Rev 33
LD1117
Package mechanical data
Table 20. Footprint data
Values
mm.
inch.
A
6.70
0.264
B
6.70
0.64
C
1.8
0.070
D
3.0
0.118
E
1.60
0.063
F
2.30
0.091
G
2.30
0.091
Figure 19. DPAK footprint recommended data
DocID2572 Rev 33
35/44
Packaging mechanical data
9
LD1117
Packaging mechanical data
Figure 20. Drawing dimension tube for TO-220 Dual Gauge (mm.)
Figure 21. Drawing dimension tube for TO-220 Single Gauge (mm.)
36/44
DocID2572 Rev 33
LD1117
Packaging mechanical data
Table 21. SOT-223 tape and reel mechanical data
Tape
Reel
mm
mm
Dim.
Dim.
Min.
Typ.
Max.
Min.
Max.
A0
6.75
6.85
6.95
A
B0
7.30
7.40
7.50
N
K0
1.80
1.90
2.00
W1
12.4
F
5.40
5.50
5.60
W2
18.4
E
1.65
1.75
1.85
W3
W
11.7
12
12.3
P2
1.90
2
2.10
Base quantity pcs
1000
P0
3.90
4
4.10
Bulk quantity pcs
1000
P1
7.90
8
8.10
T
0.25
0.30
0.35
Dφ
1.50
1.55
1.60
D1φ
1.50
1.60
1.70
180
60
11.9
15.4
Figure 22. Tape for SOT-223 (dimensions are in mm)
*Cumulative tolerance of 10 sprocket holes is ±0.20 mm
DocID2572 Rev 33
37/44
Packaging mechanical data
LD1117
Figure 23. Reel for SOT-223 (dimensions are in mm)
38/44
DocID2572 Rev 33
LD1117
Packaging mechanical data
Table 22. SO-8 tape and reel mechanical data
mm
Dim.
Min.
Typ.
A
Max.
330
C
12.8
D
20.2
N
60
13.2
T
22.4
Ao
8.1
8.5
Bo
5.5
5.9
Ko
2.1
2.3
Po
3.9
4.1
P
7.9
8.1
Figure 24. SO-8 tape and reel dimensions
DocID2572 Rev 33
39/44
Packaging mechanical data
LD1117
Table 23. DPAK tape and reel mechanical data
Tape
Reel
mm
mm
Dim.
Dim.
Min.
Max.
A0
6.8
7
A
B0
10.4
10.6
B
1.5
12.1
C
12.8
1.6
D
20.2
G
16.4
50
B1
Min.
Max.
330
13.2
D
1.5
D1
1.5
E
1.65
1.85
N
F
7.4
7.6
T
K0
2.55
2.75
P0
3.9
4.1
Base qty.
2500
P1
7.9
8.1
Bulk qty.
2500
P2
1.9
2.1
R
40
T
0.25
0.35
W
15.7
16.3
18.4
22.4
Figure 25. DPAK footprint(a)
6.7
1.8
3
1.6
2.3
6.7
2.3
1.6
a. All dimensions are in millimeters
40/44
DocID2572 Rev 33
AM08850v1
LD1117
Packaging mechanical data
Figure 26. Tape for DPAK
10 pitches cumulative
tolerance on tape +/- 0.2 mm
T
P0
Top cover
tape
P2
D
E
F
B1
W
K0
B0
For machine ref. only
including draft and
radii concentric around B0
A0
P1
D1
User direction of feed
R
Bending radius
User direction of feed
AM08852v1
Figure 27. Reel for DPAK
T
REEL DIMENSIONS
40mm min.
Access hole
At sl ot location
B
D
C
N
A
Full radius
Tape slot
in core for
tape start 25 mm min.
width
G measured at hub
AM08851v2
DocID2572 Rev 33
41/44
Order codes
10
LD1117
Order codes
Table 24. Order codes
Packages
SOT-223
SO-8
DPAK
(Tape and reel)
TO-220
TO-220
(Dual Gauge)
Output
voltages
LD1117S12TR
LD1117DT12TR
1.2 V
LD1117S12CTR
LD1117DT12CTR
1.2 V
LD1117S18TR
LD1117DT18TR
LD1117S18CTR
LD1117DT18CTR
1.8 V
LD1117S25TR
LD1117DT25TR
2.5 V
LD1117S25CTR
LD1117DT25CTR
2.5 V
LD1117S33TR
LD1117S33CTR
LD1117S50TR
LD1117D33TR
LD1117D33CTR
LD1117DT33TR
LD1117V18
LD1117V33
LD1117DT33CTR
LD1117V33C
LD1117DT50TR
LD1117V50
1.8 V
LD1117V33-DG
3.3 V
LD1117V33C-DG
3.3 V
3.3 V
LD1117V50-DG
5V
5V
LD1117S50CTR
LD1117DT50CTR
LD1117V50C
LD1117STR
LD1117DTTR
LD1117V
5V
LD1117V-DG
ADJ from
1.25 to 15 V
ADJ from
1.25 to 15 V
LD1117SC-R
42/44
LD1117DTC-R
DocID2572 Rev 33
ADJ from
1.25 to 15 V
LD1117
11
Revision history
Revision history
Table 25. Document revision history
Date
Revision
22-Sep-2004
15
Add new part number #12C; typing error: note on table 2.
25-Oct-2004
16
Add Vref reference voltage on table 12.
18-Jul-2005
17
The DPAK mechanical data updated.
25-Nov-2005
18
The TO220FM package removed.
14-Dec-2005
19
The Top on table 2 updated.
06-Dec-2006
20
DPAK mechanical data updated and added footprint data.
05-Apr-2007
21
Order codes updated.
30-Nov-2007
22
Added Table 1.
16-Apr-2008
23
Modified: Table 24 on page 42.
08-Jul-2008
24
Added note 1. on page 7.
30-Mar-2009
25
Modified: VIN max value Table 4 on page 10 and Figure 9 on page 23.
29-Jul-2009
26
Modified: Table 24 on page 42.
03-Feb-2010
27
Modified Table 9 on page 15.
22-Mar-2010
28
Added: Table 16 on page 22, Figure 13 on page 23, Figure 14 on page 24,
Figure 17 and Figure 18 on page 33.
15-Nov-2010
29
Modified: RthJC value for TO-220 Table 2 on page 7.
30-Nov-2011
30
Added: order code LD1117V33-DG Table 24 on page 42.
13-Feb-2012
31
Added: order codes LD1117V50-DG and LD1117V-DG Table 24 on page 42.
19-Oct-2012
32
Added: RthJA value for DPAK, SOT-223 and SO-8Table 2 on page 7.
33
Part number LD1117xx changed to LD1117.
Updated the Description in cover page, Section 8: Package mechanical data
and Table 24: Order codes.
Cancelled Table 1: Device summary.
Added Section 9: Packaging mechanical data.
Minor text changes.
20-Nov-2013
Changes
DocID2572 Rev 33
43/44
LD1117
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE
SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B)
AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS
OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT
PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS
EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY
DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE
DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2013 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
44/44
DocID2572 Rev 33