Features • 80C52 Compatible • • • • • • • • • • • • • • • • • • • • – 8051 Pin and Instruction Compatible – Four 8-bit I/O Ports – Three 16-bit timer/counters – 256 Bytes Scratch Pad RAM – 10 Interrupt Sources with 4 Priority Levels – Dual Data Pointer Variable Length MOVX for slow RAM/Peripherals ISP (In-System Programming) using Standard VCC Power Supply Boot ROM Contains Low Level FLASH Programming Routines and a Default Serial Loader High-Speed Architecture – 40 MHz in Standard Mode – 20 MHz in X2 Mode (6 clocks/machine cycle) 16K/32K Bytes on-chip FLASH Program/Data Memory – Byte and Page (128 Bytes) Erase and Write – 10k Write Cycles On-chip 1024 Bytes Expanded RAM (XRAM) – Software Selectable Size (0, 256, 512, 768, 1024 bytes) – 256 Bytes Selected at Reset for TS87C51RB2/RC2 Compatibility Keyboard Interrupt Interface on port P1 SPI Interface (Master / Slave Mode) 8-bit Clock Prescaler Improved X2 Mode with Independent Selection for CPU and each Peripheral Programmable Counter Array 5 Channels with: – High Speed Output – Compare / Capture – Pulse Width Modulator – Watchdog Timer Capabilities Asynchronous Port Reset Full Duplex Enhanced UART Dedicated Baud Rate Generator for UART Low EMI (Inhibit ALE) Hardware Watchdog Timer (One-time enabled with Reset-Out) Power Control Modes: – Idle Mode – Power-down mode – Power-off Flag Power supply: 4.5 to 5.5V or 2.7 to 3.6V Temperature ranges: Commercial (0 to +70°C) and Industrial (-40°C to +85°C) Packages: PDIL40, PLCC44, VQFP44 8-bit Microcontroller with 16K/ 32K byte Flash T89C51RB2 T89C51RC2 Description T89C51RB2/RC2 is a high-performance FLASH version of the 80C51 8-bit microcontrollers. It contains a 16K or 32K byte Flash memory block for program and data. The Flash memory can be programmed either in parallel mode or in serial mode with the ISP capability or with software. The programming voltage is internally generated from the standard VCC pin. The T89C51RB2/RC2 retains all features of the 80C52 with 256 bytes of internal RAM, a 7-source 4-level interrupt controller and three timer/counters. In addition, the T89C51RB2/RC2 has a Programmable Counter Array, an XRAM of 1024 bytes, a Hardware Watchdog Timer, a Keyboard Interface, an SPI Interface, Rev. 4105E–8051–02/08 1 a more versatile serial channel that facilitates multiprocessor communication (EUART) and a speed improvement mechanism (X2 mode). Pinout is the standard 40/44 pins of the C52. The fully static design reduces system power consumption of the T89C51RB2/RC2 by allowing it to bring the clock frequency down to any value, even DC, without loss of data. The T89C51RB2/RC2 has 2 software-selectable modes of reduced activity and 8-bit clock prescaler for further reduction in power consumption. In Idle mode, the CPU is frozen while the peripherals and the interrupt system are still operating. In power-down mode, the RAM is saved and all other functions are inoperative. The added features of the T89C51RB2/RC2 make it more powerful for applications that need pulse width modulation, high speed I/O and counting capabilities such as alarms, motor control, corded phones, and smart card readers. Table 1. Memory Size Part Number Flash (bytes) XRAM (bytes) TOTAL RAM (bytes) I/O T89C51RB2 16K 1024 1280 32 T89C51RC2 32K 1024 1280 32 Block Diagram (2) (2) XTAL1 XTAL2 (1) EUART + BRG ALE/ PROG RAM 256x8 C51 CORE PSEN Flash 32Kx8 or 16Kx8 XRAM 1Kx8 Boot ROM 2Kx8 (1) (1) PCA T2 T2EX PCA ECI Vss VCC TxD RxD Figure 1. Block Diagram (1) Timer2 IB-bus CPU EA Timer 0 Timer 1 (2) INT Ctrl Parallel I/O Ports & Ext. Bus Watch Key Dog Board SPI Note: SS MOSI SCK MISO P3 P2 P1 (1) (1) (1) (1) P0 INT1 (2) (2) T1 (2) (2) INT0 Port 0 Port 1 Port 2 Port 3 RESET WR (2) T0 RD 1. Alternate function of Port 1 2. Alternate function of Port 3 2 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 SFR Mapping The Special Function Registers (SFRs) of the T89C51RB2/RC2 fall into the following categories: • C51 core registers: ACC, B, DPH, DPL, PSW, SP • I/O port registers: P0, P1, P2, P3 • Timer registers: T2CON, T2MOD, TCON, TH0, TH1, TH2, TMOD, TL0, TL1, TL2, RCAP2L, RCAP2H • Serial I/O port registers: SADDR, SADEN, SBUF, SCON • PCA (Programmable Counter Array) registers: CCON, CCAPMx, CL, CH, CCAPxH, CCAPxL (x: 0 to 4) • Power and clock control registers: PCON • Hardware Watchdog Timer registers: WDTRST, WDTPRG • Interrupt system registers: IE0, IPL0, IPH0, IE1, IPL1, IPH1 • Keyboard Interface registers: KBE, KBF, KBLS • SPI registers: SPCON, SPSTR, SPDAT • BRG (Baud Rate Generator) registers: BRL, BDRCON • Flash register: FCON • Clock Prescaler register: CKRL • Others: AUXR, AUXR1, CKCON0, CKCON1 3 4105E–8051–02/08 The table below shows all SFRs with their address and their reset value. Table 2. SFR Mapping Bit addressable 0/8 F8h F0h 1/9 2/A 3/B 4/C 5/D 6/E CH CCAP0H CCAP1H CCAPL2H CCAPL3H CCAPL4H 0000 0000 XXXX XXXX XXXX XXXX XXXX CL CCAP0L CCAP1L CCAPL2L CCAPL3L CCAPL4L 0000 0000 XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX E7h CMOD CCAPM0 CCAPM1 CCAPM2 CCAPM3 CCAPM4 00XX X000 X000 0000 X000 0000 X000 0000 X000 0000 X000 0000 D0h PSW 0000 0000 FCON (a) XXXX 0000 C8h T2CON 0000 0000 T2MOD XXXX XX00 A8h A0h 98h 90h 88h 80h IPL0 SADEN X000 000 0000 0000 RCAP2L 0000 0000 RCAP2H 0000 0000 TL2 0000 0000 TH2 0000 0000 SPCON SPSTA SPDAT 0001 0100 0000 0000 XXXX XXXX CFh C7h BFh P3 IE1 IPL1 IPH1 IPH0 1111 1111 XXXXX 000 XXXXX000 XXXX X111 X000 0000 IE0 SADDR CKCON1 0000 0000 0000 0000 XXXX XXX0 P2 AUXR1 WDTRST WDTPRG 1111 1111 XXXXX0X0 XXXX XXXX XXXX X000 SCON SBUF BRL BDRCON KBLS KBE KBF 0000 0000 XXXX XXXX 0000 0000 XXX0 0000 0000 0000 0000 0000 0000 0000 P1 CKRL 1111 1111 TCON TMOD TL0 TL1 TH0 TH1 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 P0 1111 1111 SP 0000 0111 DPL 0000 0000 DPH 0000 0000 0/8 1/9 2/A 3/B FCON access is reserved for the FLASH API and ISP software Note: Reserved AUXR XX0X 0000 CKCON0 0000 0000 PCON 00X1 0000 4/C 5/D 6/E B7h AFh A7h 9Fh 1111 1111 a. 4 DFh D7h C0h B0h EFh ACC 0000 0000 CCON B8h FFh F7h 00X0 0000 D8h 7/F B 0000 0000 E8h E0h Non Bit addressable 97h 8Fh 87h 7/F T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Pin Configurations 5 36 35 P0.3/AD3 P0.4/AD4 P1.5/CEX2/MISO P0.2/AD2 P0.3/AD3 6 P0.1/AD1 P0.2/AD2 P0.1/AD1 P1.5/CEX2/MISO P1.6/CEX3/SCK 37 P0.0/AD0 3 4 VCC P1.2/ECI P1.3CEX0 P1.4/CEX1 NIC* P0.0/AD0 P1.0/T2 VCC 39 38 P1.1/T2EX/SS 40 2 P1.2/ECI 1 P1.3/CEX0 P1.0/T2 P1.1/T2EX/SS P1.4/CEX1 Figure 2. Pin Configurations 6 5 4 3 2 1 44 43 42 41 40 39 38 P0.4/AD4 7 8 34 P0.5/AD5 P1.6/CEX3/SCK 7 8 33 P0.6/AD6 P1.7/CEx4/MOSI 9 37 P0.6/AD6 9 32 P0.7/AD7 RST 10 36 P0.7/AD7 10 31 30 EA ALE/PROG P3.0/RxD 35 34 EA NIC* 11 12 13 33 ALE/PROG P3.2/INT0 32 31 P3.5/T1 27 26 14 15 PSEN 14 15 PSEN P2.7/A15 P2.6/A14 P2.5/A13 P3.1/TxD 13 29 28 16 30 P2.6/A14 P3.6/WR 16 25 17 29 P2.5/A13 P3.7/RD XTAL2 17 18 24 23 P2.2/A10 XTAL1 19 20 22 21 P2.1/A9 P3.4/T0 P3.5/T1 P2.4/A12 P2.3/A11 PLCC44 P0.5/AD5 NIC* P2.7/A15 P2.3/A11 P2.4/A12 P2.2/A10 P2.1/A9 NIC* P2.0/A8 VSS XTAL1 XTAL2 P0.3/AD3 P0.2/AD2 P0.1/AD1 P0.0/AD0 VCC NIC* P2.0/A8 P3.7/RD P3.6/WR 18 19 20 21 22 23 24 25 26 27 28 P1.4/CEX1 VSS P3.3/INT1 P1.0/T2 P3.4/T0 PDIL40 P1.1/T2EX/SS P3.2/INT0 P3.3/INT1 11 12 P1.2/ECI P3.0/RxD P3.1/TxD P1.3/CEX0 P1.7CEX4/MOSI RST 44 43 42 41 40 39 38 37 36 35 34 33 32 P0.4/AD4 31 P0.6/AD6 30 P0.7/AD7 29 28 27 EA PSEN 9 26 25 10 24 P2.6/A14 11 23 P2.5/A13 P1.5/CEX2/MISO 1 P1.6/CEX3/SCK P1.7/CEX4/MOSI 2 RST 3 4 P3.0/RxD 5 NIC* P3.1/TxD P3.2/INT0 P3.3/INT1 P3.4/T0 P3.5/T1 VQFP44 1.4 6 7 8 P0.5/AD5 NIC* ALE/PROG P2.7/A15 P2.3/A11 P2.4/A12 P2.2/A10 P2.1/A9 NIC* P2.0/A8 VSS XTAL1 XTAL2 P3.6/WR P3.7/RD 12 13 14 15 16 17 18 19 20 21 22 *NIC: No Internal Connection 5 4105E–8051–02/08 Table 3. Pin Description for 40 - 44 Pin Packages Pin Number Mnemonic DIL LCC VQFP44 1.4 Type Name and Function VSS 20 22 16 I Ground: 0V reference VCC 40 44 38 I Power Supply: This is the power supply voltage for normal, idle and power - down operation P0.0 - P0.7 39 - 32 43 - 36 37 - 30 I/O Port 0: Port 0 is an open-drain, bidirectional I/O port. Port 0 pins that have 1s written to them float and can be used as high impedance inputs. Port 0 must be polarized to VCC or VSS in order to prevent any parasitic current consumption. Port 0 is also the multiplexed low - order address and data bus during access to external program and data memory. In this application, it uses strong internal pull - up when emitting 1s. Port 0 also inputs the code bytes during FLASH programming. External pull - ups are required during program verification during which P0 outputs the code bytes. P1.0 - P1.7 1-8 2-9 40 - 44 1-3 I/O Port 1: Port 1 is an 8 - bit bidirectional I/O port with internal pull - ups. Port 1 pins that have 1s written to them are pulled high by the internal pull - ups and can be used as inputs. As inputs, Port 1 pins that are externally pulled low will source current because of the internal pull - ups. Port 1 also receives the low - order address byte during memory programming and verification. Alternate functions for T89C51RB2/RC2 Port 1 include: 1 2 3 2 3 4 40 41 42 I/O P1.0: Input / Output I/O T2 (P1.0): Timer/Counter 2 external count input/Clockout I/O P1.1: Input / Output I T2EX: Timer/Counter 2 Reload/Capture/Direction Control I SS: SPI Slave Select I/O I 4 5 6 5 6 7 43 44 1 P1.2: Input / Output ECI: External Clock for the PCA I/O P1.3: Input / Output I/O CEX0: Capture/Compare External I/O for PCA module 0 I/O P1.4: Input / Output I/O CEX1: Capture/Compare External I/O for PCA module 1 I/O P1.5: Input / Output I/O CEX2: Capture/Compare External I/O for PCA module 2 I/O MISO: SPI Master Input Slave Output line When SPI is in master mode, MISO receives data from the slave peripheral. When SPI is in slave mode, MISO outputs data to the master controller. 7 8 2 I/O P1.6: Input / Output I/O CEX3: Capture/Compare External I/O for PCA module 3 I/O SCK: SPI Serial Clock SCK outputs clock to the slave peripheral 8 6 9 3 I/O P1.7: Input / Output: T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Table 3. Pin Description for 40 - 44 Pin Packages (Continued) Pin Number Mnemonic DIL LCC VQFP44 1.4 P1.0 - P1.7 Type Name and Function I/O CEX4: Capture/Compare External I/O for PCA module 4 I/O MOSI: SPI Master Output Slave Input line When SPI is in master mode, MOSI outputs data to the slave peripheral. When SPI is in slave mode, MOSI receives data from the master controller. XTAL1 19 21 15 I Crystal 1: Input to the inverting oscillator amplifier and input to the internal clock generator circuits. XTAL2 18 20 14 O Crystal 2: Output from the inverting oscillator amplifier 21 - 28 24 - 31 18 - 25 I/O Port 2: Port 2 is an 8 - bit bidirectional I/O port with internal pull - ups. Port 2 pins that have 1s written to them are pulled high by the internal pull - ups and can be used as inputs. As inputs, Port 2 pins that are externally pulled low will source current because of the internal pull - ups. Port 2 emits the high - order address byte during fetches from external program memory and during accesses to external data memory that use 16 - bit addresses (MOVX @DPTR). In this application, it uses strong internal pull - ups emitting 1s. During accesses to external data memory that use 8 - bit addresses (MOVX @Ri), port 2 emits the contents of the P2 SFR. Some Port 2 pins receive the high order address bits during EPROM programming and verification: P2.0 - P2.7 P2.0 to P2.5 for 16 KB devices P2.0 to P2.6 for 32KB devices P3.0 - P3.7 Port 3: Port 3 is an 8 - bit bidirectional I/O port with internal pull - ups. Port 3 pins that have 1s written to them are pulled high by the internal pull - ups and can be used as inputs. As inputs, Port 3 pins that are externally pulled low will source current because of the internal pull - ups. Port 3 also serves the special features of the 80C51 family, as listed below. 10 - 17 11, 13 - 19 5, 7 - 13 I/O 10 11 5 I RXD (P3.0): Serial input port 11 13 7 O TXD (P3.1): Serial output port 12 14 8 I INT0 (P3.2): External interrupt 0 13 15 9 I INT1 (P3.3): External interrupt 1 14 16 10 I T0 (P3.4): Timer 0 external input 15 17 11 I T1 (P3.5): Timer 1 external input 16 18 12 O WR (P3.6): External data memory write strobe 17 19 13 O RD (P3.7): External data memory read strobe Reset: A high on this pin for two machine cycles while the oscillator is running, resets the device. An internal diffused resistor to VSS permits a power - on reset using only an external capacitor to VCC. This pin is an output when the hardware watchdog forces a system reset. RST 9 10 4 I/O ALE/PROG 30 33 27 O (I) Address Latch Enable/Program Pulse: Output pulse for latching the low byte of the address during an access to external memory. In normal operation, ALE is emitted at a constant rate of 1/6 (1/3 in X2 mode) the oscillator frequency, and can be used for external timing or clocking. Note that one ALE pulse is skipped during each access to external data memory. This pin is also the program pulse input (PROG) during Flash programming. ALE can be disabled by setting SFR’s AUXR. 0 bit. With this bit set, ALE will be inactive during internal fetches. 7 4105E–8051–02/08 Table 3. Pin Description for 40 - 44 Pin Packages (Continued) Pin Number Mnemonic DIL LCC VQFP44 1.4 Type Name and Function PSEN 29 32 26 O Program Strobe ENable: The read strobe to external program memory. When executing code from the external program memory, PSEN is activated twice each machine cycle, except that two PSEN activations are skipped during each access to external data memory. PSEN is not activated during fetches from internal program memory. EA 31 35 29 I External Access Enable: EA must be externally held low to enable the device to fetch code from external program memory locations 0000H to FFFFH (RD). If security level 1 is programmed, EA will be internally latched on Reset. 8 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Oscillator In order to optimize the power consumption and execution time needed for a specific task, an internal, prescaler feature has been implemented between oscillator and the CPU and peripherals. Registers Table 4. CKRL Register CKRL – Clock Reload Register (97h) 7 6 5 4 3 2 1 0 - - - - - - - - Bit Number Mnemonic 7:0 CKRL Description Clock Reload Register: Prescaler value Reset Value = 1111 1111b Not bit addressable Table 5. PCON Register PCON – Power Control Register (87h) 7 6 5 4 3 2 1 0 SMOD1 SMOD0 - POF GF1 GF0 PD IDL Bit Number Bit Mnemonic Description 7 SMOD1 Serial port Mode bit 1 Set to select double baud rate in mode 1, 2 or 3. 6 SMOD0 Serial port Mode bit 0 Cleared to select SM0 bit in SCON register. Set to select FE bit in SCON register. 5 - Reserved The value read from this bit is indeterminate. Do not set this bit. 4 POF Power-Off Flag Cleared to recognize next reset type. Set by hardware when VCC rises from 0 to its nominal voltage. Can also be set by software. 3 GF1 General Purpose Flag Cleared by software for general purpose usage. Set by software for general purpose usage. 2 GF0 General Purpose Flag Cleared by software for general purpose usage. Set by software for general purpose usage. 1 PD Power-Down mode bit Cleared by hardware when reset occurs. Set to enter power-down mode. 0 IDL Idle mode bit Cleared by hardware when interrupt or reset occurs. Set to enter idle mode. Reset Value = 00X1 0000b Not bit addressable 9 4105E–8051–02/08 Functional Block Diagram Figure 3. Functional Oscillator Block Diagram Reload Reset CKRL FOSC Xtal1 Osc 1 Xtal2 :2 0 8-bit Prescaler-Divider CLK PERIPH CLK CPU X2 • A hardware RESET puts the prescaler divider in the following state: • • CPU clock Idle CKCON0 Prescaler Divider Peripheral Clock CKRL = FFh: FCLK CPU = FCLK PERIPH = FOSC/2 (Standard C51 feature) Any value between FFh down to 00h can be written by software into CKRL register in order to divide frequency of the selected oscillator: • CKRL = 00h: minimum frequency FCLK CPU = FCLK PERIPH = FOSC/1020 (Standard Mode) FCLK CPU = FCLK PERIPH = FOSC/510 (X2 Mode) • CKRL = FFh: maximum frequency FCLK CPU = FCLK PERIPH = FOSC/2 (Standard Mode) FCLK CPU = FCLK PERIPH = FOSC (X2 Mode) FCLK CPU and FCLK PERIPH In X2 Mode: F OSC F CPU = F CLKPERIPH = ---------------------------------------------- 2 × ( 255 – CKRL ) In X1 Mode: F OSC F CPU = F CLKPERIPH = ---------------------------------------------- 4 × ( 255 – CKRL ) 10 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Enhanced Features X2 Feature In comparison to the original 80C52, the T89C51RB2/RC2 implements some new features, which are: • the X2 option • the Dual Data Pointer • the extended RAM • the Programmable Counter Array (PCA) • the Hardware Watchdog • the SPI interface • the 4-level interrupt priority system • the power-off flag • the ONCE mode • the ALE disabling • some enhanced features are also located in the UART and the timer 2 The T89C51RB2/RC2 core needs only 6 clock periods per machine cycle. This feature called ‘X2’ provides the following advantages: • Divide frequency crystals by 2 (cheaper crystals) while keeping same CPU power. • Save power consumption while keeping same CPU power (oscillator power saving). • Save power consumption by dividing dynamically the operating frequency by 2 in operating and idle modes. • Increase CPU power by 2 while keeping same crystal frequency. In order to keep the original C51 compatibility, a divider by 2 is inserted between the XTAL1 signal and the main clock input of the core (phase generator). This divider may be disabled by software. Description The clock for the whole circuit and peripherals is first divided by two before being used by the CPU core and the peripherals. This allows any cyclic ratio to be accepted on XTAL1 input. In X2 mode, as this divider is bypassed, the signals on XTAL1 must have a cyclic ratio between 40 to 60%. Figure 4 shows the clock generation block diagram. X2 bit is validated on the rising edge of the XTAL1÷2 to avoid glitches when switching from X2 to STD mode. Figure 5 shows the switching mode waveforms. Figure 4. Clock Generation Diagram CKRL 2 XTAL1 FXTAL FOSC XTAL1:2 0 1 8 bit Prescaler FCLK CPU FCLK PERIPH X2 CKCON0 11 4105E–8051–02/08 Figure 5. Mode Switching Waveforms XTAL1 XTAL1:2 X2 bit FOSC CPU clock STD Mode X2 Mode STD Mode The X2 bit in the CKCON0 register (see Table 6) allows a switch from 12 clock periods per instruction to 6 clock periods and vice versa. At reset, the speed is set according to X2 bit of Hardware Security Byte (HSB). By default, Standard mode is active. Setting the X2 bit activates the X2 feature (X2 mode). The T0X2, T1X2, T2X2, UartX2, PcaX2, and WdX2 bits in the CKCON0 register (See Table 6.) and SPIX2 bit in the CKCON1 register (see Table 7) allows a switch from standard peripheral speed (12 clock periods per peripheral clock cycle) to fast peripheral speed (6 clock periods per peripheral clock cycle). These bits are active only in X2 mode. 12 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Table 6. CKCON0 Register CKCON0 - Clock Control Register (8Fh) 7 6 5 4 3 2 1 0 - WDX2 PCAX2 SIX2 T2X2 T1X2 T0X2 X2 Bit Number 7 Bit Mnemonic Description Reserved Watchdog Clock 6 WDX2 (This control bit is validated when the CPU clock X2 is set; when X2 is low, this bit has no effect). Cleared to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. Programmable Counter Array Clock 5 PCAX2 (This control bit is validated when the CPU clock X2 is set; when X2 is low, this bit has no effect). Cleared to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. Enhanced UART Clock (Mode 0 and 2) 4 SIX2 (This control bit is validated when the CPU clock X2 is set; when X2 is low, this bit has no effect). Cleared to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. Timer2 Clock 3 T2X2 (This control bit is validated when the CPU clock X2 is set; when X2 is low, this bit has no effect). Cleared to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. Timer1 Clock 2 T1X2 (This control bit is validated when the CPU clock X2 is set; when X2 is low, this bit has no effect). Cleared to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. Timer0 Clock 1 T0X2 (This control bit is validated when the CPU clock X2 is set; when X2 is low, this bit has no effect). Cleared to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. CPU Clock 0 X2 Cleared to select 12 clock periods per machine cycle (STD mode) for CPU and all the peripherals. Set to select 6clock periods per machine cycle (X2 mode) and to enable the individual peripherals’X2’ bits. Programmed by hardware after Power-up regarding Hardware Security Byte (HSB), Default setting, X2 is cleared. Reset Value = 0000 000’HSB. X2’b (See Table 70 “Hardware Security Byte”) Not bit addressable 13 4105E–8051–02/08 Table 7. CKCON1 Register CKCON1 - Clock Control Register (AFh) 7 6 5 4 3 2 1 0 - - - - - - - SPIX2 Bit Number Bit Mnemonic Description 7 - Reserved 6 - Reserved 5 - Reserved 4 - Reserved 3 - Reserved 2 - Reserved 1 - Reserved 0 SPIX2 SPI (This control bit is validated when the CPU clock X2 is set; when X2 is low, this bit has no effect). Clear to select 6 clock periods per peripheral clock cycle. Set to select 12 clock periods per peripheral clock cycle. Reset Value = XXXX XXX0b Not bit addressable 14 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Dual Data Pointer Register DPTR The additional data pointer can be used to speed up code execution and reduce code size. The dual DPTR structure is a way by which the chip will specify the address of an external data memory location. There are two 16-bit DPTR registers that address the external memory, and a single bit called DPS = AUXR1.0 (see Table 8) that allows the program code to switch between them (Refer to Figure 6). Figure 6. Use of Dual Pointer External Data Memory 7 0 DPS AUXR1(A2H) DPTR1 DPTR0 DPH(83H) DPL(82H) 15 4105E–8051–02/08 Table 8. AUXR1 register AUXR1- Auxiliary Register 1(0A2h) 7 6 5 4 3 2 1 0 - - ENBOOT - GF3 0 - DPS Bit Bit Number Mnemonic Description 7 - Reserved The value read from this bit is indeterminate. Do not set this bit. 6 - Reserved The value read from this bit is indeterminate. Do not set this bit. 5 ENBOOT Enable Boot Flash Cleared to disable boot ROM. Set to map the boot ROM between F800h - 0FFFFh. Reserved The value read from this bit is indeterminate. Do not set this bit. 4 - 3 GF3 2 0 Always cleared. 1 - Reserved The value read from this bit is indeterminate. Do not set this bit. 0 DPS This bit is a general purpose user flag. * Data Pointer Selection Cleared to select DPTR0. Set to select DPTR1. Reset Value: XXXX XX0X0b Not bit addressable Note: *Bit 2 stuck at 0; this allows to use INC AUXR1 to toggle DPS without changing GF3. ASSEMBLY LANGUAGE ; Block move using dual data pointers ; Modifies DPTR0, DPTR1, A and PSW ; note: DPS exits opposite of entry state ; unless an extra INC AUXR1 is added ; 00A2 AUXR1 EQU 0A2H ; 0000 909000MOV DPTR,#SOURCE ; address of SOURCE 0003 05A2 INC AUXR1 ; switch data pointers 0005 90A000 MOV DPTR,#DEST ; address of DEST 0008 LOOP: 0008 05A2 INC AUXR1 ; switch data pointers 000A E0 MOVX A,@DPTR ; get a byte from SOURCE 000B A3 INC DPTR ; increment SOURCE address 000C 05A2 INC AUXR1 ; switch data pointers 000E F0 MOVX @DPTR,A ; write the byte to DEST 000F A3 INC DPTR ; increment DEST address 0010 70F6JNZ LOOP ; check for 0 terminator 0012 05A2 INC AUXR1 ; (optional) restore DPS 16 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 INC is a short (2 bytes) and fast (12 clocks) way to manipulate the DPS bit in the AUXR1 SFR. However, note that the INC instruction does not directly force the DPS bit to a particular state, but simply toggles it. In simple routines, such as the block move example, only the fact that DPS is toggled in the proper sequence matters, not its actual value. In other words, the block move routine works the same whether DPS is '0' or '1' on entry. Observe that without the last instruction (INC AUXR1), the routine will exit with DPS in the opposite state. 17 4105E–8051–02/08 Expanded RAM (XRAM) The T89C51RB2/RC2 provides additional Bytes of random access memory (RAM) space for increased data parameter handling and high level language usage. T89C51RB2/RC2 devices have expanded RAM in external data space; maximum size and location are described in Table 9. Table 9. Expanded RAM Address Part Number T89C51RB2/RC2 XRAM size Start End 1024 00h 3FFh The T89C51RB2/RC2 has internal data memory that is mapped into four separate segments. The four segments are: 1. The Lower 128 bytes of RAM (addresses 00h to 7Fh) are directly and indirectly addressable. 2. The Upper 128 bytes of RAM (addresses 80h to FFh) are indirectly addressable only. 3. The Special Function Registers, SFRs, (addresses 80h to FFh) are directly addressable only. 4. The expanded RAM bytes are indirectly accessed by MOVX instructions, and with the EXTRAM bit cleared in the AUXR register (see Table 9). The lower 128 bytes can be accessed by either direct or indirect addressing. The Upper 128 bytes can be accessed by indirect addressing only. The Upper 128 bytes occupy the same address space as the SFR. That means they have the same address, but are physically separate from SFR space. Figure 7. Internal and External Data Memory Address 0FFh or 3FFh 0FFh 0FFh Upper 128 bytes Internal Ram indirect accesses 80h XRAM 0FFFFh Special Function Register direct accesses External Data Memory 80h 7Fh Lower 128 bytes Internal Ram direct or indirect accesses 00 00 00FFh up to 03FFh 0000 When an instruction accesses an internal location above address 7Fh, the CPU knows whether the access is to the upper 128 bytes of data RAM or to SFR space by the addressing mode used in the instruction. • 18 Instructions that use direct addressing access SFR space. For example: MOV 0A0H, # data, accesses the SFR at location 0A0h (which is P2). T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 • Instructions that use indirect addressing access the Upper 128 bytes of data RAM. For example: MOV @R0, # data where R0 contains 0A0h, accesses the data byte at address 0A0h, rather than P2 (whose address is 0A0h). • The XRAM bytes can be accessed by indirect addressing, with EXTRAM bit cleared and MOVX instructions. This part of memory which is physically located on-chip, logically occupies the first bytes of external data memory. The bits XRS0 and XRS1 are used to hide a part of the available XRAM as explained in Table 9. This can be useful if external peripherals are mapped at addresses already used by the internal XRAM. • With EXTRAM = 0, the XRAM is indirectly addressed, using the MOVX instruction in combination with any of the registers R0, R1 of the selected bank or DPTR. An access to XRAM will not affect ports P0, P2, P3.6 (WR) and P3.7 (RD). For example, with EXTRAM = 0, MOVX @R0, # data where R0 contains 0A0H, accesses the XRAM at address 0A0H rather than external memory. An access to external data memory locations higher than the accessible size of the XRAM will be performed with the MOVX DPTR instructions in the same way as in the standard 80C51, with P0 and P2 as data/address busses, and P3.6 and P3.7 as write and read timing signals. Accesses to XRAM above 0FFH can only be done by the use of DPTR. • With EXTRAM = 1, MOVX @Ri and MOVX @DPTR will be similar to the standard 80C51.MOVX @ Ri will provide an eight-bit address multiplexed with data on Port0 and any output port pins can be used to output higher order address bits. This is to provide the external paging capability. MOVX @DPTR will generate a sixteen-bit address. Port2 outputs the high-order eight address bits (the contents of DPH) while Port0 multiplexes the low-order eight address bits (DPL) with data. MOVX @ Ri and MOVX @DPTR will generate either read or write signals on P3.6 (WR) and P3.7 (RD). The stack pointer (SP) may be located anywhere in the 256 bytes RAM (lower and upper RAM) internal data memory. The stack may not be located in the XRAM. The M0 bit allows to stretch the XRAM timings; if M0 is set, the read and write pulses are extended from 6 to 30 clock periods. This is useful to access external slow peripherals. 19 4105E–8051–02/08 Registers Table 10. AUXR Register AUXR - Auxiliary Register (8Eh) 7 6 5 4 3 2 1 0 - - M0 - XRS1 XRS0 EXTRAM AO Bit Number Bit Mnemonic Description 7 - 6 - Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Pulse length 5 M0 Cleared to stretch MOVX control: the RD/ and the WR/ pulse length is 6 clock periods (default). Set to stretch MOVX control: the RD/ and the WR/ pulse length is 30 clock periods. 4 - 3 XRS1 2 XRS0 Reserved The value read from this bit is indeterminate. Do not set this bit. XRAM Size XRS1 0 XRS0 0 XRAM size 256 bytes (default) 0 1 512 bytes 1 0 768 bytes 1 1 1024 bytes EXTRAM bit Cleared to access internal XRAM using movx @ Ri/ @ DPTR. 1 EXTRAM Set to access external memory. Programmed by hardware after Power-up regarding Hardware Security Byte (HSB), default setting, XRAM selected. 0 AO ALE Output bit Cleared, ALE is emitted at a constant rate of 1/6 the oscillator frequency (or 1/3 if X2 mode is used). (default) Set, ALE is active only during a MOVX or MOVC instruction is used. Reset Value = XX0X 00’HSB. XRAM’0b (See Table 70) Not bit addressable 20 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Timer 2 The Timer 2 in the T89C51RB2/RC2 is the standard C52 Timer 2. It is a 16-bit timer/counter: the count is maintained by two eight-bit timer registers, TH2 and TL2 are cascaded. It is controlled by T2CON (Table 11) and T2MOD (Table 12) registers. Timer 2 operation is similar to Timer 0 and Timer 1.C/T2 selects FOSC/12 (timer operation) or external pin T2 (counter operation) as the timer clock input. Setting TR2 allows TL2 to increment by the selected input. Timer 2 has 3 operating modes: capture, autoreload and Baud Rate Generator. These modes are selected by the combination of RCLK, TCLK and CP/RL2 (T2CON). Refer to the Atmel 8-bit Microcontroller Hardware description for the description of Capture and Baud Rate Generator Modes. Timer 2 includes the following enhancements: Auto-Reload Mode • Auto-reload mode with up or down counter • Programmable clock-output The auto-reload mode configures Timer 2 as a 16-bit timer or event counter with automatic reload. If DCEN bit in T2MOD is cleared, Timer 2 behaves as in 80C52 (refer to the Atmel C51 Microcontroller Hardware description). If DCEN bit is set, Timer 2 acts as an Up/down timer/counter as shown in Figure 8. In this mode the T2EX pin controls the direction of count. When T2EX is high, Timer 2 counts up. Timer overflow occurs at FFFFh which sets the TF2 flag and generates an interrupt request. The overflow also causes the 16-bit value in RCAP2H and RCAP2L registers to be loaded into the timer registers TH2 and TL2. When T2EX is low, Timer 2 counts down. Timer underflow occurs when the count in the timer registers TH2 and TL2 equals the value stored in RCAP2H and RCAP2L registers. The underflow sets TF2 flag and reloads FFFFh into the timer registers. The EXF2 bit toggles when Timer 2 overflows or underflows according to the direction of the count. EXF2 does not generate any interrupt. This bit can be used to provide 17-bit resolution. 21 4105E–8051–02/08 Figure 8. Auto-Reload Mode Up/Down Counter (DCEN = 1) FCLK PERIPH :6 0 1 T2 C/T2 TR2 T2CON T2CON T2EX: (DOWN COUNTING RELOAD VALUE) if DCEN=1, 1=UP FFh FFh if DCEN=1, 0=DOWN (8-bit) (8-bit) if DCEN = 0, up counting TOGGLE T2CON EXF2 TL2 TH2 (8-bit) (8-bit) TIMER 2 INTERRUPT TF2 T2CON RCAP2L (8-bit) RCAP2H (8-bit) (UP COUNTING RELOAD VALUE) Programmable ClockOutput In the clock-out mode, Timer 2 operates as a 50%-duty-cycle, programmable clock generator (See Figure 9). The input clock increments TL2 at frequency FCLK PERIPH/2.The timer repeatedly counts to overflow from a loaded value. At overflow, the contents of RCAP2H and RCAP2L registers are loaded into TH2 and TL2.In this mode, Timer 2 overflows do not generate interrupts. The formula gives the clock-out frequency as a function of the system oscillator frequency and the value in the RCAP2H and RCAP2L registers: F CLKPERIPH Clock – O utFrequency = --------------------------------------------------------------------------------------------4 × ( 65536 – RCAP2H ⁄ RCAP2L ) For a 16 MHz system clock, Timer 2 has a programmable frequency range of 61 Hz (FCLK PERIPH/216) to 4 MHz (FCLK PERIPH/4). The generated clock signal is brought out to T2 pin (P1.0). Timer 2 is programmed for the clock-out mode as follows: • Set T2OE bit in T2MOD register. • Clear C/T2 bit in T2CON register. • Determine the 16-bit reload value from the formula and enter it in RCAP2H/RCAP2L registers. • Enter a 16-bit initial value in timer registers TH2/TL2.It can be the same as the reload value or a different one depending on the application. • To start the timer, set TR2 run control bit in T2CON register. It is possible to use Timer 2 as a baud rate generator and a clock generator simultaneously. For this configuration, the baud rates and clock frequencies are not independent since both functions use the values in the RCAP2H and RCAP2L registers. 22 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Figure 9. Clock-Out Mode C/T2 = 0 FCLK PERIPH :6 TR2 T2CON TL2 (8-bit) TH2 (8-bit) OVERFLOW RCAP2L RCAP2H (8-bit) (8-bit) Toggle T2 Q D T2EX T2OE T2MOD EXF2 EXEN2 T2CON T2CON TIMER 2 INTERRUPT 23 4105E–8051–02/08 Registers Table 11. T2CON Register T2CON - Timer 2 Control Register (C8h) 7 6 5 4 3 2 1 0 TF2 EXF2 RCLK TCLK EXEN2 TR2 C/T2# CP/RL2# Bit Number 7 Bit Mnemonic Description TF2 Timer 2 overflow Flag Must be cleared by software. Set by hardware on Timer 2 overflow, if RCLK = 0 and TCLK = 0. 6 EXF2 Timer 2 External Flag Set when a capture or a reload is caused by a negative transition on T2EX pin if EXEN2=1. When set, causes the CPU to vector to Timer 2 interrupt routine when Timer 2 interrupt is enabled. Must be cleared by software. EXF2 doesn’t cause an interrupt in Up/down counter mode (DCEN = 1). 5 RCLK Receive Clock bit Cleared to use timer 1 overflow as receive clock for serial port in mode 1 or 3. Set to use Timer 2 overflow as receive clock for serial port in mode 1 or 3. 4 TCLK Transmit Clock bit Cleared to use timer 1 overflow as transmit clock for serial port in mode 1 or 3. Set to use Timer 2 overflow as transmit clock for serial port in mode 1 or 3. 3 EXEN2 2 TR2 1 0 Timer 2 External Enable bit Cleared to ignore events on T2EX pin for Timer 2 operation. Set to cause a capture or reload when a negative transition on T2EX pin is detected, if Timer 2 is not used to clock the serial port. Timer 2 Run control bit Cleared to turn off Timer 2. Set to turn on Timer 2. C/T2# Timer/Counter 2 select bit Cleared for timer operation (input from internal clock system: FCLK PERIPH). Set for counter operation (input from T2 input pin, falling edge trigger). Must be 0 for clock out mode. CP/RL2# Timer 2 Capture/Reload bit If RCLK=1 or TCLK=1, CP/RL2# is ignored and timer is forced to auto-reload on Timer 2 overflow. Cleared to auto-reload on Timer 2 overflows or negative transitions on T2EX pin if EXEN2=1. Set to capture on negative transitions on T2EX pin if EXEN2=1. Reset Value = 0000 0000b Bit addressable 24 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Table 12. T2MOD Register T2MOD - Timer 2 Mode Control Register (C9h) 7 6 5 4 3 2 1 0 - - - - - - T2OE DCEN Bit Number Bit Mnemonic Description 7 - Reserved The value read from this bit is indeterminate. Do not set this bit. 6 - Reserved The value read from this bit is indeterminate. Do not set this bit. 5 - Reserved The value read from this bit is indeterminate. Do not set this bit. 4 - Reserved The value read from this bit is indeterminate. Do not set this bit. 3 - Reserved The value read from this bit is indeterminate. Do not set this bit. 2 - Reserved The value read from this bit is indeterminate. Do not set this bit. 1 T2OE Timer 2 Output Enable bit Cleared to program P1.0/T2 as clock input or I/O port. Set to program P1.0/T2 as clock output. 0 DCEN Down Counter Enable bit Cleared to disable Timer 2 as up/down counter. Set to enable Timer 2 as up/down counter. Reset Value = XXXX XX00b Not bit addressable 25 4105E–8051–02/08 Programmable Counter Array PCA The PCA provides more timing capabilities with less CPU intervention than the standard timer/counters. Its advantages include reduced software overhead and improved accuracy. The PCA consists of a dedicated timer/counter which serves as the time base for an array of five compare/capture modules. Its clock input can be programmed to count any one of the following signals: ÷6 • Peripheral clock frequency (FCLK PERIPH) • Peripheral clock frequency (FCLK PERIPH) ÷ 2 • Timer 0 overflow • External input on ECI (P1.2) Each compare/capture modules can be programmed in any one of the following modes: • rising and/or falling edge capture • software timer • high-speed output • pulse width modulator Module 4 can also be programmed as a watchdog timer (See Section "PCA Watchdog Timer", page 37). When the compare/capture modules are programmed in the capture mode, software timer, or high speed output mode, an interrupt can be generated when the module executes its function. All five modules plus the PCA timer overflow share one interrupt vector. The PCA timer/counter and compare/capture modules share Port 1 for external I/O. These pins are listed below. If the port is not used for the PCA, it can still be used for standard I/O. PCA component External I/O Pin 16-bit Counter P1.2 / ECI 16-bit Module 0 P1.3 / CEX0 16-bit Module 1 P1.4 / CEX1 16-bit Module 2 P1.5 / CEX2 16-bit Module 3 P1.6 / CEX3 The PCA timer is a common time base for all five modules (See Figure 10). The timer count source is determined from the CPS1 and CPS0 bits in the CMOD register (Table 13) and can be programmed to run at: 26 • 1/6 the peripheral clock frequency (FCLK PERIPH) • 1/2 the peripheral clock frequency (FCLK PERIPH) • The Timer 0 overflow • The input on the ECI pin (P1.2) T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Figure 10. PCA Timer/Counter To PCA modules Fclk periph /6 overflow Fclk periph / 2 CH T0 OVF It CL 16 bit up/down counter P1.2 CIDL WDTE CF CR CPS1 CPS0 ECF CMOD 0xD9 CCF2 CCF1 CCF0 CCON 0xD8 Idle CCF4 CCF3 27 4105E–8051–02/08 Registers Table 13. CMOD Register CMOD - PCA Counter Mode Register (D9h) 7 6 5 4 3 2 1 0 CIDL WDTE - - - CPS1 CPS0 ECF Bit Number Bit Mnemonic Description Counter Idle Control 7 CIDL Cleared to program the PCA Counter to continue functioning during idle Mode. Set to program PCA to be gated off during idle. Watchdog Timer Enable 6 WDTE Cleared to disable Watchdog Timer function on PCA Module 4. Set to enable Watchdog Timer function on PCA Module 4. 5 - Reserved The value read from this bit is indeterminate. Do not set this bit. 4 - Reserved The value read from this bit is indeterminate. Do not set this bit. 3 - Reserved The value read from this bit is indeterminate. Do not set this bit. 2 CPS1 1 0 CPS0 ECF PCA Count Pulse Select CPS1 CPS0 0 0 Selected PCA input Internal clock fCLK PERIPH/6 0 1 Internal clock fCLK PERIPH/2 1 0 Timer 0 Overflow 1 1 External clock at ECI/P1.2 pin (max rate = fCLK PERIPH/ 4) PCA Enable Counter Overflow Interrupt Cleared to disable CF bit in CCON to inhibit an interrupt. Set to enable CF bit in CCON to generate an interrupt. Reset Value = 00XX X000b Not bit addressable The CMOD register includes three additional bits associated with the PCA (See Figure 10 and Table 13). • The CIDL bit which allows the PCA to stop during idle mode. • The WDTE bit which enables or disables the watchdog function on module 4. • The ECF bit which when set causes an interrupt and the PCA overflow flag CF (in the CCON SFR) to be set when the PCA timer overflows. The CCON register contains the run control bit for the PCA and the flags for the PCA timer (CF) and each module (Refer to Table 14). 28 • Bit CR (CCON. 6) must be set by software to run the PCA. The PCA is shut off by clearing this bit. • Bit CF: The CF bit (CCON. 7) is set when the PCA counter overflows and an interrupt will be generated if the ECF bit in the CMOD register is set. The CF bit can only be cleared by software. • Bits 0 through 4 are the flags for the modules (bit 0 for module 0, bit 1 for module 1, etc. ) and are set by hardware when either a match or a capture occurs. These flags also can only be cleared by software. T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Table 14. CCON Register CCON - PCA Counter Control Register (D8h) 7 6 5 4 3 2 1 0 CF CR - CCF4 CCF3 CCF2 CCF1 CCF0 Bit Number Bit Mnemonic Description PCA Counter Overflow flag 7 CF 6 CR Set by hardware when the counter rolls over. CF flags an interrupt if bit ECF in CMOD is set. CF may be set by either hardware or software but can only be cleared by software. PCA Counter Run control bit Must be cleared by software to turn the PCA counter off. Set by software to turn the PCA counter on. 5 - 4 CCF4 Reserved The value read from this bit is indeterminate. Do not set this bit. PCA Module 4 interrupt flag Must be cleared by software. Set by hardware when a match or capture occurs. PCA Module 3 interrupt flag 3 CCF3 Must be cleared by software. Set by hardware when a match or capture occurs. PCA Module 2 interrupt flag 2 CCF2 Must be cleared by software. Set by hardware when a match or capture occurs. PCA Module 1 interrupt flag 1 CCF1 Must be cleared by software. Set by hardware when a match or capture occurs. PCA Module 0 interrupt flag 0 CCF0 Must be cleared by software. Set by hardware when a match or capture occurs. Reset Value = 000X 0000b Not bit addressable The watchdog timer function is implemented in module 4 (See Figure 13). The PCA interrupt system is shown in Figure 11. 29 4105E–8051–02/08 Figure 11. PCA Interrupt System CF CR CCF4 CCF3 CCF2 CCF1 CCF0 CCON 0xD8 PCA Timer/Counter Module 0 Module 1 To Interrupt priority decoder Module 2 Module 3 Module 4 CMOD. 0 ECF ECCFn CCAPMn. 0 IE. 6 EC IE. 7 EA PCA Modules: each one of the five compare/capture modules has six possible functions. It can perform: • 16-bit Capture, positive-edge triggered • 16-bit Capture, negative-edge triggered • 16-bit Capture, both positive and negative-edge triggered • 16-bit Software Timer • 16-bit High Speed Output • 8-bit Pulse Width Modulator In addition, module 4 can be used as a Watchdog Timer. Each module in the PCA has a special function register associated with it. These registers are: CCAPM0 for module 0, CCAPM1 for module 1, etc. (See Table 15). The registers contain the bits that control the mode that each module will operate in. • The ECCF bit (CCAPMn. 0 where n = 0, 1, 2, 3, or 4 depending on the module) enables the CCF flag in the CCON SFR to generate an interrupt when a match or compare occurs in the associated module. • PWM (CCAPMn. 1) enables the pulse width modulation mode. • The TOG bit (CCAPMn. 2) when set causes the CEX output associated with the module to toggle when there is a match between the PCA counter and the module's capture/compare register. • The match bit MAT (CCAPMn. 3) when set will cause the CCFn bit in the CCON register to be set when there is a match between the PCA counter and the module's capture/compare register. • The next two bits CAPN (CCAPMn. 4) and CAPP (CCAPMn. 5) determine the edge that a capture input will be active on. The CAPN bit enables the negative edge, and the CAPP bit enables the positive edge. If both bits are set both edges will be enabled and a capture will occur for either transition. • The last bit in the register ECOM (CCAPMn. 6) when set enables the comparator function. Table 15 shows the CCAPMn settings for the various PCA functions. 30 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Table 15. CCAPMn Registers (n = 0-4) CCAPM0 - PCA Module 0 Compare/Capture Control Register (0DAh) CCAPM1 - PCA Module 1 Compare/Capture Control Register (0DBh) CCAPM2 - PCA Module 2 Compare/Capture Control Register (0DCh) CCAPM3 - PCA Module 3 Compare/Capture Control Register (0DDh) CCAPM4 - PCA Module 4 Compare/Capture Control Register (0DEh) 7 6 5 4 3 2 1 0 - ECOMn CAPPn CAPNn MATn TOGn PWMn ECCFn Bit Number Bit Mnemonic Description 7 - 6 ECOMn Reserved The value read from this bit is indeterminate. Do not set this bit. Enable Comparator Cleared to disable the comparator function. Set to enable the comparator function. Capture Positive 5 CAPPn 4 CAPNn Cleared to disable positive edge capture. Set to enable positive edge capture. Capture Negative Cleared to disable negative edge capture. Set to enable negative edge capture. Match 3 MATn 2 TOGn 1 PWMn When MATn = 1, a match of the PCA counter with this module's compare/capture register causes the CCFn bit in CCON to be set, flagging an interrupt. Toggle When TOGn = 1, a match of the PCA counter with this module's compare/capture register causes theCEXn pin to toggle. Pulse Width Modulation Mode Cleared to disable the CEXn pin to be used as a pulse width modulated output. Set to enable the CEXn pin to be used as a pulse width modulated output. Enable CCF interrupt 0 CCF0 Cleared to disable compare/capture flag CCFn in the CCON register to generate an interrupt. Set to enable compare/capture flag CCFn in the CCON register to generate an interrupt. Reset Value = X000 0000b Not bit addressable 31 4105E–8051–02/08 Table 16. PCA Module Modes (CCAPMn Registers) ECOMn CAPPn CAPNn MATn TOGn PWMm ECCFn Module Function 0 0 0 0 0 0 0 No Operation X 1 0 0 0 0 X 16-bit capture by a positive-edge trigger on CEXn X 0 1 0 0 0 X 16-bit capture by a negative trigger on CEXn X 1 1 0 0 0 X 16-bit capture by a transition on CEXn 1 0 0 1 0 0 X 16-bit Software Timer / Compare mode. 1 0 0 1 1 0 X 16-bit High Speed Output 1 0 0 0 0 1 0 8-bit PWM 1 0 0 1 X 0 X Watchdog Timer (module 4 only) There are two additional registers associated with each of the PCA modules. They are CCAPnH and CCAPnL and these are the registers that store the 16-bit count when a capture occurs or a compare should occur. When a module is used in the PWM mode these registers are used to control the duty cycle of the output (See Table 17 & Table 18). Table 17. CCAPnH Registers (n = 0-4) CCAP0H - PCA Module 0 Compare/Capture Control Register High (0FAh) CCAP1H - PCA Module 1 Compare/Capture Control Register High (0FBh) CCAP2H - PCA Module 2 Compare/Capture Control Register High (0FCh) CCAP3H - PCA Module 3 Compare/Capture Control Register High (0FDh) CCAP4H - PCA Module 4 Compare/Capture Control Register High (0FEh) 7 6 5 4 3 2 1 0 - - - - - - - - Bit Number 7-0 Bit Mnemonic Description - PCA Module n Compare/Capture Control CCAPnH Value Reset Value = 0000 0000b Not bit addressable 32 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Table 18. CCAPnL Registers (n = 0-4) CCAP0L - PCA Module 0 Compare/Capture Control Register Low (0EAh) CCAP1L - PCA Module 1 Compare/Capture Control Register Low (0EBh) CCAP2L - PCA Module 2 Compare/Capture Control Register Low (0ECh) CCAP3L - PCA Module 3 Compare/Capture Control Register Low (0EDh) CCAP4L - PCA Module 4 Compare/Capture Control Register Low (0EEh) 7 6 5 4 3 2 1 0 - - - - - - - - Bit Number 7-0 Bit Mnemonic Description - PCA Module n Compare/Capture Control CCAPnL Value Reset Value = 0000 0000b Not bit addressable Table 19. CH Register CH - PCA Counter Register High (0F9h) 7 6 5 4 3 2 1 0 - - - - - - - - Bit Number 7-0 Bit Mnemonic Description - PCA counter CH Value Reset Value = 0000 0000b Not bit addressable Table 20. CL Register CL - PCA Counter Register Low (0E9h) 7 6 5 4 3 2 1 0 - - - - - - - - Bit Number 7-0 Bit Mnemonic Description - PCA Counter CL Value Reset Value = 0000 0000b Not bit addressable 33 4105E–8051–02/08 PCA Capture Mode To use one of the PCA modules in the capture mode either one or both of the CCAPM bits CAPN and CAPP for that module must be set. The external CEX input for the module (on port 1) is sampled for a transition. When a valid transition occurs the PCA hardware loads the value of the PCA counter registers (CH and CL) into the module's capture registers (CCAPnL and CCAPnH). If the CCFn bit for the module in the CCON SFR and the ECCFn bit in the CCAPMn SFR are set then an interrupt will be generated (Refer to Figure 12). Figure 12. PCA Capture Mode CF CR CCF4 CCF3 CCF2 CCF1 CCF0 CCON 0xD8 PCA IT PCA Counter/Timer Cex. n CH CL CCAPnH CCAPnL Capture ECOMn CAPPn CAPNn MATn TOGn PWMn ECCFn CCAPMn, n= 0 to 4 0xDA to 0xDE 34 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 16-bit Software Timer/ Compare Mode The PCA modules can be used as software timers by setting both the ECOM and MAT bits in the modules CCAPMn register. The PCA timer will be compared to the module's capture registers and when a match occurs, an interrupt will occur if the CCFn (CCON SFR) and the ECCFn (CCAPMn SFR) bits for the module are both set (See Figure 13). Figure 13. PCA Compare Mode and PCA Watchdog Timer CCON CF Write to CCAPnL CR CCF4 CCF3 CCF2 CCF1 CCF0 0xD8 Reset PCA IT Write to CCAPnH 1 CCAPnH 0 CCAPnL Enable Match 16 bit comparator CH RESET * CL PCA counter/timer ECOMn CAPPn CAPNn MATn TOGn PWMn ECCFn CIDL WDTE CPS1 CPS0 ECF CCAPMn, n = 0 to 4 0xDA to 0xDE CMOD 0xD9 * Only for Module 4 Before enabling ECOM bit, CCAPnL and CCAPnH should be set with a non zero value, otherwise an unwanted match could happen. Writing to CCAPnH will set the ECOM bit. Once ECOM set, writing CCAPnL will clear ECOM so that an unwanted match doesn’t occur while modifying the compare value. Writing to CCAPnH will set ECOM. For this reason, user software should write CCAPnL first, and then CCAPnH. Of course, the ECOM bit can still be controlled by accessing to CCAPMn register. 35 4105E–8051–02/08 High Speed Output Mode In this mode the CEX output (on port 1) associated with the PCA module will toggle each time a match occurs between the PCA counter and the module's capture registers. To activate this mode the TOG, MAT, and ECOM bits in the module's CCAPMn SFR must be set (See Figure 14). A prior write must be done to CCAPnL and CCAPnH before writing the ECOMn bit. Figure 14. PCA High Speed Output Mode CCON CF CR CCF4 CCF3 CCF2 CCF1 CCF0 0xD8 Write to CCAPnL Reset PCA IT Write to CCAPnH 1 CCAPnH 0 CCAPnL Enable 16 bit comparator CH Match CL CEXn PCA counter/timer ECOMn CAPPn CAPNn MATn TOGn PWMn ECCFn CCAPMn, n = 0 to 4 0xDA to 0xDE Before enabling ECOM bit, CCAPnL and CCAPnH should be set with a non zero value, otherwise an unwanted match could happen. Once ECOM set, writing CCAPnL will clear ECOM so that an unwanted match doesn’t occur while modifying the compare value. Writing to CCAPnH will set ECOM. For this reason, user software should write CCAPnL first, and then CCAPnH. Of course, the ECOM bit can still be controlled by accessing to CCAPMn register. 36 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Pulse Width Modulator Mode All of the PCA modules can be used as PWM outputs. Figure 15 shows the PWM function. The frequency of the output depends on the source for the PCA timer. All of the modules will have the same frequency of output because they all share the PCA timer. The duty cycle of each module is independently variable using the module's capture register CCAPLn. When the value of the PCA CL SFR is less than the value in the module's CCAPLn SFR the output will be low, when it is equal to or greater than the output will be high. When CL overflows from FF to 00, CCAPLn is reloaded with the value in CCAPHn. This allows updating the PWM without glitches. The PWM and ECOM bits in the module's CCAPMn register must be set to enable the PWM mode. Figure 15. PCA PWM Mode CCAPnH Overflow CCAPnL “0” CEXn Enable 8 bit comparator “1” CL PCA counter/timer ECOMn CAPPn CAPNn MATn TOGn PWMn ECCFn CCAPMn, n= 0 to 4 0xDA to 0xDE PCA Watchdog Timer An on-board watchdog timer is available with the PCA to improve the reliability of the system without increasing chip count. Watchdog timers are useful for systems that are susceptible to noise, power glitches, or electrostatic discharge. Module 4 is the only PCA module that can be programmed as a watchdog. However, this module can still be used for other modes if the watchdog is not needed. Figure 13 shows a diagram of how the watchdog works. The user pre-loads a 16-bit value in the compare registers. Just like the other compare modes, this 16-bit value is compared to the PCA timer value. If a match is allowed to occur, an internal reset will be generated. This will not cause the RST pin to be driven high. In order to hold off the reset, the user has three options: • periodically change the compare value so it will never match the PCA timer, • periodically change the PCA timer value so it will never match the compare values, or • disable the watchdog by clearing the WDTE bit before a match occurs and then reenable it. The first two options are more reliable because the watchdog timer is never disabled as in option #3.If the program counter ever goes astray, a match will eventually occur and 37 4105E–8051–02/08 cause an internal reset. The second option is also not recommended if other PCA modules are being used. Remember, the PCA timer is the time base for all modules; changing the time base for other modules would not be a good idea. Thus, in most applications the first solution is the best option. This watchdog timer won’t generate a reset out on the reset pin. 38 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Serial I/O Port The serial I/O port in the T89C51RB2/RC2 is compatible with the serial I/O port in the 80C52. It provides both synchronous and asynchronous communication modes. It operates as a Universal Asynchronous Receiver and Transmitter (UART) in three full-duplex modes (Modes 1, 2 and 3). Asynchronous transmission and reception can occur simultaneously and at different baud rates Serial I/O port includes the following enhancements: Framing Error Detection • Framing error detection • Automatic address recognition Framing bit error detection is provided for the three asynchronous modes (modes 1, 2 and 3). To enable the framing bit error detection feature, set SMOD0 bit in PCON register (See Figure 16). Figure 16. Framing Error Block Diagram SM0/FE SM1 SM2 REN TB8 RB8 TI RI SCON (98h) Set FE bit if stop bit is 0 (framing error) (SMOD0 = 1) SM0 to UART mode control (SMOD0 = 0) SMOD1SMOD0 - POF GF1 GF0 PD IDL PCON (87h) To UART framing error control When this feature is enabled, the receiver checks each incoming data frame for a valid stop bit. An invalid stop bit may result from noise on the serial lines or from simultaneous transmission by two CPUs. If a valid stop bit is not found, the Framing Error bit (FE) in SCON register (See Table 24.) bit is set. Software may examine FE bit after each reception to check for data errors. Once set, only software or a reset can clear FE bit. Subsequently received frames with valid stop bits cannot clear FE bit. When FE feature is enabled, RI rises on stop bit instead of the last data bit (See Figure 17. and Figure 18.). Figure 17. UART Timings in Mode 1 RXD D0 Start bit D1 D2 D3 D4 Data byte D5 D6 D7 Stop bit RI SMOD0=X FE SMOD0=1 39 4105E–8051–02/08 Figure 18. UART Timings in Modes 2 and 3 RXD D0 Start bit D1 D2 D3 D4 Data byte D5 D6 D7 D8 Ninth Stop bit bit RI SMOD0=0 RI SMOD0=1 FE SMOD0=1 Automatic Address Recognition The automatic address recognition feature is enabled when the multiprocessor communication feature is enabled (SM2 bit in SCON register is set). Implemented in hardware, automatic address recognition enhances the multiprocessor communication feature by allowing the serial port to examine the address of each incoming command frame. Only when the serial port recognizes its own address, the receiver sets RI bit in SCON register to generate an interrupt. This ensures that the CPU is not interrupted by command frames addressed to other devices. If desired, the user may enable the automatic address recognition feature in mode 1.In this configuration, the stop bit takes the place of the ninth data bit. Bit RI is set only when the received command frame address matches the device’s address and is terminated by a valid stop bit. To support automatic address recognition, a device is identified by a given address and a broadcast address. Note: Given Address The multiprocessor communication and automatic address recognition features cannot be enabled in mode 0 (i. e. setting SM2 bit in SCON register in mode 0 has no effect). Each device has an individual address that is specified in SADDR register; the SADEN register is a mask byte that contains don’t-care bits (defined by zeros) to form the device’s given address. The don’t-care bits provide the flexibility to address one or more slaves at a time. The following example illustrates how a given address is formed. To address a device by its individual address, the SADEN mask byte must be 1111 1111b. For example: SADDR0101 0110b SADEN1111 1100b Given0101 01XXb The following is an example of how to use given addresses to address different slaves: Slave A:SADDR1111 0001b SADEN1111 1010b Given1111 0X0Xb Slave B:SADDR1111 0011b SADEN1111 1001b Given1111 0XX1b Slave C:SADDR1111 0010b SADEN1111 1101b Given1111 00X1b 40 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 The SADEN byte is selected so that each slave may be addressed separately. For slave A, bit 0 (the LSB) is a don’t-care bit; for slaves B and C, bit 0 is a 1.To communicate with slave A only, the master must send an address where bit 0 is clear (e. g. 1111 0000b). For slave A, bit 1 is a 1; for slaves B and C, bit 1 is a don’t care bit. To communicate with slaves B and C, but not slave A, the master must send an address with bits 0 and 1 both set (e. g. 1111 0011b). To communicate with slaves A, B and C, the master must send an address with bit 0 set, bit 1 clear, and bit 2 clear (e. g. 1111 0001b). Broadcast Address A broadcast address is formed from the logical OR of the SADDR and SADEN registers with zeros defined as don’t-care bits, e. g. : SADDR0101 0110b SADEN1111 1100b Broadcast =SADDR OR SADEN1111 111Xb The use of don’t-care bits provides flexibility in defining the broadcast address, however in most applications, a broadcast address is FFh. The following is an example of using broadcast addresses: Slave A:SADDR1111 0001b SADEN1111 1010b Broadcast1111 1X11b, Slave B:SADDR1111 0011b SADEN1111 1001b Broadcast1111 1X11B, Slave C:SADDR=1111 0010b SADEN1111 1101b Broadcast1111 1111b For slaves A and B, bit 2 is a don’t care bit; for slave C, bit 2 is set. To communicate with all of the slaves, the master must send an address FFh. To communicate with slaves A and B, but not slave C, the master can send and address FBh. Reset Addresses On reset, the SADDR and SADEN registers are initialized to 00h, i. e. the given and broadcast addresses are XXXX XXXXb (all don’t-care bits). This ensures that the serial port will reply to any address, and so, that it is backwards compatible with the 80C51 microcontrollers that do not support automatic address recognition. 41 4105E–8051–02/08 Registers Table 21. SADEN Register SADEN - Slave Address Mask Register (B9h) 7 6 5 4 3 2 1 0 3 2 1 0 Reset Value = 0000 0000b Not bit addressable Table 22. SADDR Register SADDR - Slave Address Register (A9h) 7 6 5 4 Reset Value = 0000 0000b Not bit addressable Baud Rate Selection for UART for Mode 1 and 3 The Baud Rate Generator for transmit and receive clocks can be selected separately via the T2CON and BDRCON registers. Figure 19. Baud Rate Selection TIMER1 TIMER2 0 TIMER_BRG_RX 0 1 / 16 Rx Clock 1 RCLK RBCK INT_BRG TIMER1 TIMER2 0 1 TIMER_BRG_TX 0 1 / 16 Tx Clock TCLK INT_BRG 42 TBCK T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Table 23. Baud Rate Selection Table UART Internal Baud Rate Generator (BRG) TCLK RCLK TBCK RBCK Clock Source Clock Source (T2CON) (T2CON) (BDRCON) (BDRCON) UART Tx UART Rx 0 0 0 0 Timer 1 Timer 1 1 0 0 0 Timer 2 Timer 1 0 1 0 0 Timer 1 Timer 2 1 1 0 0 Timer 2 Timer 2 X 0 1 0 INT_BRG Timer 1 X 1 1 0 INT_BRG Timer 2 0 X 0 1 Timer 1 INT_BRG 1 X 0 1 Timer 2 INT_BRG X X 1 1 INT_BRG INT_BRG When the internal Baud Rate Generator is used, the Baud Rates are determined by the BRG overflow depending on the BRL reload value, the value of SPD bit (Speed Mode) in BDRCON register and the value of the SMOD1 bit in PCON register. Figure 20. Internal Baud Rate CLK PERIPH 0 /6 auto reload counter overflow BRG /2 1 SPD 0 INT_BRG 1 BRL SMOD1 BRR • The baud rate for UART is token by formula: Baud_Rate = 2SMOD1 x FCLK PERIPH 2 x 2 x 6(1-SPD) x 16 x [256 - (BRL)] (BRL) = 256 - 2SMOD1 x FCLK PERIPH 2 x 2 x 6(1-SPD) x 16 x Baud_Rate 43 4105E–8051–02/08 Table 24. SCON Register SCON - Serial Control Register (98h) 7 6 5 4 3 2 1 0 FE/SM0 SM1 SM2 REN TB8 RB8 TI RI Bit Bit Number Mnemonic Description Framing Error bit (SMOD0=1) 7 FE Clear to reset the error state, not cleared by a valid stop bit. Set by hardware when an invalid stop bit is detected. SMOD0 must be set to enable access to the FE bit. SM0 Serial port Mode bit 0 Refer to SM1 for serial port mode selection. SMOD0 must be cleared to enable access to the SM0 bit. 6 SM1 Serial port Mode bit 1 SM0 SM1 Mode Description Baud Rate 0 0 1 0 1 0 0 1 2 Shift Register 8-bit UART 9-bit UART FCPU PERIPH/6 Variable FCPU PERIPH /32 or /16 1 1 3 9-bit UART Variable Serial port Mode 2 bit / Multiprocessor Communication Enable bit 5 SM2 4 REN 3 TB8 Clear to disable multiprocessor communication feature. Set to enable multiprocessor communication feature in mode 2 and 3, and eventually mode 1.This bit should be cleared in mode 0. Reception Enable bit Clear to disable serial reception. Set to enable serial reception. Transmitter Bit 8 / Ninth bit to transmit in modes 2 and 3 2 RB8 Clear to transmit a logic 0 in the 9th bit. Set to transmit a logic 1 in the 9th bit. Receiver Bit 8 / Ninth bit received in modes 2 and 3 Cleared by hardware if 9th bit received is a logic 0. Set by hardware if 9th bit received is a logic 1. In mode 1, if SM2 = 0, RB8 is the received stop bit. In mode 0 RB8 is not used. 1 0 TI Transmit Interrupt flag Clear to acknowledge interrupt. Set by hardware at the end of the 8th bit time in mode 0 or at the beginning of the stop bit in the other modes. RI Receive Interrupt flag Clear to acknowledge interrupt. Set by hardware at the end of the 8th bit time in mode 0, see Figure 17. and Figure 18. in the other modes. Reset Value = 0000 0000b Bit addressable 44 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Table 25. Example of Computed Value When X2=1, SMOD1=1, SPD=1 Baud Rates FOSC = 16. 384 MHz FOSC = 24MHz BRL Error (%) BRL Error (%) 115200 247 1.23 243 0.16 57600 238 1.23 230 0.16 38400 229 1.23 217 0.16 28800 220 1.23 204 0.16 19200 203 0.63 178 0.16 9600 149 0.31 100 0.16 4800 43 1.23 - - Table 26. Example of Computed Value When X2=0, SMOD1=0, SPD=0 FOSC = 16. 384 MHz Baud Rates FOSC = 24MHz BRL Error (%) BRL Error (%) 4800 247 1.23 243 0.16 2400 238 1.23 230 0.16 1200 220 1.23 202 3.55 600 185 0.16 152 0.16 The baud rate generator can be used for mode 1 or 3 (refer to Figure 19.), but also for mode 0 for UART, thanks to the bit SRC located in BDRCON register (Table 33.) UART Registers Table 27. SADEN Register SADEN - Slave Address Mask Register for UART (B9h) 7 6 5 4 3 2 1 0 2 1 0 Reset Value = 0000 0000b Table 28. SADDR Register SADDR - Slave Address Register for UART (A9h) 7 6 5 4 3 Reset Value = 0000 0000b 45 4105E–8051–02/08 Table 29. SBUF Register SBUF - Serial Buffer Register for UART (99h) 7 6 5 4 3 2 1 0 Reset Value = XXXX XXXXb Table 30. BRL Register BRL - Baud Rate Reload Register for the internal baud rate generator, UART (9Ah) 7 6 5 4 3 2 1 0 Reset Value = 0000 0000b 46 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Table 31. T2CON Register T2CON - Timer 2 Control Register (C8h) 7 6 5 4 3 2 1 0 TF2 EXF2 RCLK TCLK EXEN2 TR2 C/T2# CP/RL2# Bit Bit Number Mnemonic 7 TF2 Description Timer 2 overflow Flag Must be cleared by software. Set by hardware on timer 2 overflow, if RCLK = 0 and TCLK = 0. 6 EXF2 Timer 2 External Flag Set when a capture or a reload is caused by a negative transition on T2EX pin if EXEN2=1. When set, causes the CPU to vector to timer 2 interrupt routine when timer 2 interrupt is enabled. Must be cleared by software. EXF2 doesn’t cause an interrupt in Up/down counter mode (DCEN = 1) 5 RCLK Receive Clock bit for UART Cleared to use timer 1 overflow as receive clock for serial port in mode 1 or 3. Set to use timer 2 overflow as receive clock for serial port in mode 1 or 3. 4 TCLK Transmit Clock bit for UART Cleared to use timer 1 overflow as transmit clock for serial port in mode 1 or 3. Set to use timer 2 overflow as transmit clock for serial port in mode 1 or 3. 3 EXEN2 2 TR2 1 0 Timer 2 External Enable bit Cleared to ignore events on T2EX pin for timer 2 operation. Set to cause a capture or reload when a negative transition on T2EX pin is detected, if timer 2 is not used to clock the serial port. Timer 2 Run control bit Cleared to turn off timer 2. Set to turn on timer 2. C/T2# Timer/Counter 2 select bit Cleared for timer operation (input from internal clock system: FCLK PERIPH). Set for counter operation (input from T2 input pin, falling edge trigger). Must be 0 for clock out mode. CP/RL2# Timer 2 Capture/Reload bit If RCLK=1 or TCLK=1, CP/RL2# is ignored and timer is forced to auto-reload on timer 2 overflow. Cleared to auto-reload on timer 2 overflows or negative transitions on T2EX pin if EXEN2=1. Set to capture on negative transitions on T2EX pin if EXEN2=1. Reset Value = 0000 0000b Bit addressable 47 4105E–8051–02/08 Table 32. PCON Register PCON - Power Control Register (87h) 7 6 5 4 3 2 1 0 SMOD1 SMOD0 - POF GF1 GF0 PD IDL Bit Bit Number Mnemonic 7 SMOD1 6 SMOD0 5 - Description Serial port Mode bit 1 for UART Set to select double baud rate in mode 1, 2 or 3. Serial port Mode bit 0 for UART Cleared to select SM0 bit in SCON register. Set to select FE bit in SCON register. Reserved The value read from this bit is indeterminate. Do not set this bit. 4 POF Power-Off Flag Cleared to recognize next reset type. Set by hardware when VCC rises from 0 to its nominal voltage. Can also be set by software. 3 GF1 General purpose Flag Cleared by user for general purpose usage. Set by user for general purpose usage. 2 GF0 General purpose Flag Cleared by user for general purpose usage. Set by user for general purpose usage. 1 PD Power-Down mode bit Cleared by hardware when reset occurs. Set to enter power-down mode. 0 IDL Idle mode bit Cleared by hardware when interrupt or reset occurs. Set to enter idle mode. Reset Value = 00X1 0000b Not bit addressable Power-off flag reset value will be 1 only after a power on (cold reset). A warm reset doesn’t affect the value of this bit. 48 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Table 33. BDRCON Register BDRCON - Baud Rate Control Register (9Bh) 7 6 5 4 3 2 1 0 - - - BRR TBCK RBCK SPD SRC Bit Number Bit Mnemonic 7 - Reserved The value read from this bit is indeterminate. Do not set this bit 6 - Reserved The value read from this bit is indeterminate. Do not set this bit 5 - Reserved The value read from this bit is indeterminate. Do not set this bit. 4 BRR Baud Rate Run Control bit Cleared to stop the internal Baud Rate Generator. Set to start the internal Baud Rate Generator. 3 TBCK Transmission Baud rate Generator Selection bit for UART Cleared to select Timer 1 or Timer 2 for the Baud Rate Generator. Set to select internal Baud Rate Generator. 2 RBCK Reception Baud Rate Generator Selection bit for UART Cleared to select Timer 1 or Timer 2 for the Baud Rate Generator. Set to select internal Baud Rate Generator. 1 SPD Description Baud Rate Speed Control bit for UART Cleared to select the SLOW Baud Rate Generator. Set to select the FAST Baud Rate Generator. Baud Rate Source select bit in Mode 0 for UART 0 SRC Cleared to select FOSC/12 as the Baud Rate Generator (FCLK PERIPH/6 in X2 mode). Set to select the internal Baud Rate Generator for UARTs in mode 0. Reset Value = XXX0 0000b Not bit addressablef 49 4105E–8051–02/08 Interrupt System The T89C51RB2/RC2 has a total of 10 interrupt vectors: two external interrupts (INT0 and INT1), three timer interrupts (timers 0, 1 and 2), the serial port interrupt, SPI interrupt, Keyboard interrupt and the PCA global interrupt. These interrupts are shown in Figure 21. Figure 21. Interrupt Control System High priority interrupt IPH, IPL 3 INT0 IE0 0 3 TF0 0 3 INT1 IE1 0 3 TF1 Interrupt polling sequence, decreasing from high to low priority 0 3 PCA IT 0 RI TI 3 TF2 EXF2 3 0 0 3 KBD IT 0 3 SPI IT 0 Individual Enable Global Disable Low priority interrupt Each of the interrupt sources can be individually enabled or disabled by setting or clearing a bit in the Interrupt Enable register (Table 38 and Table 36). This register also contains a global disable bit, which must be cleared to disable all interrupts at once. Each interrupt source can also be individually programmed to one out of four priority levels by setting or clearing a bit in the Interrupt Priority register (Table 39) and in the Interrupt Priority High register (Table 37 and Table 38) shows the bit values and priority levels associated with each combination. 50 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Registers The PCA interrupt vector is located at address 0033H, the SPI interrupt vector is located at address 0043H and Keyboard interrupt vector is located at address 004BH. All other vectors addresses are the same as standard C52 devices. Table 34. Priority Level Bit Values IPH. x IPL. x Interrupt Level Priority 0 0 0 (Lowest) 0 1 1 1 0 2 1 1 3 (Highest) A low-priority interrupt can be interrupted by a high priority interrupt, but not by another low-priority interrupt. A high-priority interrupt can’t be interrupted by any other interrupt source. If two interrupt requests of different priority levels are received simultaneously, the request of higher priority level is serviced. If interrupt requests of the same priority level are received simultaneously, an internal polling sequence determines which request is serviced. Thus within each priority level there is a second priority structure determined by the polling sequence. 51 4105E–8051–02/08 Table 35. IEO Register IE0 - Interrupt Enable Register (A8h) 7 6 5 4 3 2 1 0 EA EC ET2 ES ET1 EX1 ET0 EX0 Bit Number Bit Mnemonic Description 7 EA 6 EC Enable All interrupt bit Cleared to disable all interrupts. Set to enable all interrupts. PCA interrupt enable bit Cleared to disable. Set to enable. 5 ET2 Timer 2 overflow interrupt Enable bit Cleared to disable timer 2 overflow interrupt. Set to enable timer 2 overflow interrupt. 4 ES Serial port Enable bit Cleared to disable serial port interrupt. Set to enable serial port interrupt. 3 ET1 Timer 1 overflow interrupt Enable bit Cleared to disable timer 1 overflow interrupt. Set to enable timer 1 overflow interrupt. 2 EX1 External interrupt 1 Enable bit Cleared to disable external interrupt 1. Set to enable external interrupt 1. 1 ET0 Timer 0 overflow interrupt Enable bit Cleared to disable timer 0 overflow interrupt. Set to enable timer 0 overflow interrupt. 0 EX0 External interrupt 0 Enable bit Cleared to disable external interrupt 0. Set to enable external interrupt 0. Reset Value = 0000 0000b Bit addressable 52 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Table 36. IPL0 Register IPL0 - Interrupt Priority Register (B8h) 7 6 5 4 3 2 1 0 - PPCL PT2L PSL PT1L PX1L PT0L PX0L Bit Number Bit Mnemonic Description Reserved The value read from this bit is indeterminate. Do not set this bit. 7 - 6 PPCL PCA interrupt Priority bit Refer to PPCH for priority level. 5 PT2L Timer 2 overflow interrupt Priority bit Refer to PT2H for priority level. 4 PSL Serial port Priority bit Refer to PSH for priority level. 3 PT1L Timer 1 overflow interrupt Priority bit Refer to PT1H for priority level. 2 PX1L External interrupt 1 Priority bit Refer to PX1H for priority level. 1 PT0L Timer 0 overflow interrupt Priority bit Refer to PT0H for priority level. 0 PX0L External interrupt 0 Priority bit Refer to PX0H for priority level. Reset Value = X000 0000b Bit addressable 53 4105E–8051–02/08 Table 37. IPH0 Register IPH0 - Interrupt Priority High Register (B7h) 7 6 5 4 3 2 1 0 - PPCH PT2H PSH PT1H PX1H PT0H PX0H Bit Number 7 6 5 4 3 2 1 0 Bit Mnemonic Description - Reserved The value read from this bit is indeterminate. Do not set this bit. PPCH PCA interrupt Priority high bit. PPCH PPCL Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest PT2H Timer 2 overflow interrupt Priority High bit PT2H PT2L Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest PSH Serial port Priority High bit PSH PSL Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest PT1H Timer 1 overflow interrupt Priority High bit PT1H PT1L Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest PX1H External interrupt 1 Priority High bit PX1H PX1L Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest PT0H Timer 0 overflow interrupt Priority High bit PT0H PT0L Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest PX0H External interrupt 0 Priority High bit PX0H PX0L Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest Reset Value = X000 0000b Not bit addressable 54 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Table 38. IE1 Register IE1 - Interrupt Enable Register (B1h) 7 6 5 4 3 2 1 0 - - - - - SPI - KBD Bit Number Bit Mnemonic Description 7 - Reserved 6 - Reserved 5 - Reserved 4 - Reserved 3 - Reserved 2 SPI SPI interrupt Enable bit Cleared to disable SPI interrupt. Set to enable SPI interrupt. 1 - 0 KBD Reserved Keyboard interrupt Enable bit Cleared to disable keyboard interrupt. Set to enable keyboard interrupt. Reset Value = XXXX X000b Bit addressable 55 4105E–8051–02/08 Table 39. IPL1 Register IPL1 - Interrupt Priority Register (B2h) 7 6 5 4 3 2 1 0 - - - - - SPIL - KBDL Bit Number Bit Mnemonic Description 7 - Reserved The value read from this bit is indeterminate. Do not set this bit. 6 - Reserved The value read from this bit is indeterminate. Do not set this bit. 5 - Reserved The value read from this bit is indeterminate. Do not set this bit. 4 - Reserved The value read from this bit is indeterminate. Do not set this bit. 3 - Reserved The value read from this bit is indeterminate. Do not set this bit. 2 SPIL 1 - 0 KBDL SPI interrupt Priority bit Refer to SPIH for priority level. Reserved The value read from this bit is indeterminate. Do not set this bit. Keyboard interrupt Priority bit Refer to KBDH for priority level. Reset Value = XXXX X000b Bit addressable 56 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Table 40. IPH1 Register IPH1 - Interrupt Priority High Register (B3h) 7 6 5 4 3 2 1 0 - - - - - SPIH - KBDH Bit Number Bit Mnemonic Description 7 - Reserved The value read from this bit is indeterminate. Do not set this bit. 6 - Reserved The value read from this bit is indeterminate. Do not set this bit. 5 - Reserved The value read from this bit is indeterminate. Do not set this bit. 4 - Reserved The value read from this bit is indeterminate. Do not set this bit. 3 - Reserved The value read from this bit is indeterminate. Do not set this bit. 2 SPIH 1 - 0 KBDH SPI interrupt Priority High bit SPIH SPIL Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest Reserved The value read from this bit is indeterminate. Do not set this bit. Keyboard interrupt Priority High bit KB DH KBDL Priority Level 0 0 Lowest 0 1 1 0 1 1 Highest Reset Value = XXXX X000b Not bit addressable 57 4105E–8051–02/08 Interrupt Sources and Vector Addresses 58 Table 41. Interrupt Sources and Vector Addresses Interrupt Request Vector Number Polling Priority Interrupt Source Address 0 0 Reset 1 1 INT0 IE0 0003h 2 2 Timer 0 TF0 000Bh 3 3 INT1 IE1 0013h 4 4 Timer 1 IF1 001Bh 5 6 UART RI+TI 0023h 6 7 Timer 2 TF2+EXF2 002Bh 7 5 PCA CF + CCFn (n = 0-4) 0033h 8 8 Keyboard KBDIT 003Bh 9 9 SPI SPIIT 004Bh 0000h T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Keyboard Interface The T89C51RB2/RC2 implements a keyboard interface allowing the connection of a 8 x n matrix keyboard. It is based on 8 inputs with programmable interrupt capability on both high or low level. These inputs are available as alternate function of P1 and allow to exit from idle and power down modes. The keyboard interface interfaces with the C51 core through 3 special function registers: KBLS, the Keyboard Level Selection register (Table 44), KBE, The Keyboard interrupt Enable register (Table 43), and KBF, the Keyboard Flag register (Table 42). Interrupt The keyboard inputs are considered as 8 independent interrupt sources sharing the same interrupt vector. An interrupt enable bit (KBD in IE1) allows global enable or disable of the keyboard interrupt (see Figure 22). As detailed in Figure 23 each keyboard input has the capability to detect a programmable level according to KBLS. x bit value. Level detection is then reported in interrupt flags KBF. x that can be masked by software using KBE. x bits. This structure allow keyboard arrangement from 1 by n to 8 by n matrix and allow usage of P1 inputs for other purpose. Figure 22. Keyboard Interface Block Diagram Vcc 0 P1:x KBF. x 1 Internal Pullup KBE. x KBLS. x Figure 23. Keyboard Input Circuitry P1.0 Input Circuitry P1.1 Input Circuitry P1.2 Input Circuitry P1.3 Input Circuitry P1.4 Input Circuitry P1.5 Input Circuitry P1.6 Input Circuitry P1.7 Input Circuitry KBDIT Power Reduction Mode KBD IE1 Keyboard Interface Interrupt Request P1 inputs allow exit from idle and power down modes as detailed in Section “Powerdown Mode”, page 76. 59 4105E–8051–02/08 Registers Table 42. KBF Register KBF-Keyboard Flag Register (9Eh) 7 6 5 4 3 2 1 0 KBF7 KBF6 KBF5 KBF4 KBF3 KBF2 KBF1 KBF0 Bit Number 7 6 5 4 3 2 1 0 Bit Mnemonic Description KBF7 Keyboard line 7 flag Set by hardware when the Port line 7 detects a programmed level. It generates a Keyboard interrupt request if the KBKBIE. 7 bit in KBIE register is set. Must be cleared by software. KBF6 Keyboard line 6 flag Set by hardware when the Port line 6 detects a programmed level. It generates a Keyboard interrupt request if the KBIE. 6 bit in KBIE register is set. Must be cleared by software. KBF5 Keyboard line 5 flag Set by hardware when the Port line 5 detects a programmed level. It generates a Keyboard interrupt request if the KBIE. 5 bit in KBIE register is set. Must be cleared by software. KBF4 Keyboard line 4 flag Set by hardware when the Port line 4 detects a programmed level. It generates a Keyboard interrupt request if the KBIE. 4 bit in KBIE register is set. Must be cleared by software. KBF3 Keyboard line 3 flag Set by hardware when the Port line 3 detects a programmed level. It generates a Keyboard interrupt request if the KBIE. 3 bit in KBIE register is set. Must be cleared by software. KBF2 Keyboard line 2 flag Set by hardware when the Port line 2 detects a programmed level. It generates a Keyboard interrupt request if the KBIE. 2 bit in KBIE register is set. Must be cleared by software. KBF1 Keyboard line 1 flag Set by hardware when the Port line 1 detects a programmed level. It generates a Keyboard interrupt request if the KBIE. 1 bit in KBIE register is set. Must be cleared by software. KBF0 Keyboard line 0 flag Set by hardware when the Port line 0 detects a programmed level. It generates a Keyboard interrupt request if the KBIE. 0 bit in KBIE register is set. Must be cleared by software. Reset Value= 0000 0000b 60 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Table 43. KBE Register KBE-Keyboard Input Enable Register (9Dh) 7 6 5 4 3 2 1 0 KBE7 KBE6 KBE5 KBE4 KBE3 KBE2 KBE1 KBE0 Bit Number Bit Mnemonic Description 7 KBE7 Keyboard line 7 Enable bit Cleared to enable standard I/O pin. Set to enable KBF. 7 bit in KBF register to generate an interrupt request. 6 KBE6 Keyboard line 6 Enable bit Cleared to enable standard I/O pin. Set to enable KBF. 6 bit in KBF register to generate an interrupt request. 5 KBE5 Keyboard line 5 Enable bit Cleared to enable standard I/O pin. Set to enable KBF. 5 bit in KBF register to generate an interrupt request. 4 KBE4 Keyboard line 4 Enable bit Cleared to enable standard I/O pin. Set to enable KBF. 4 bit in KBF register to generate an interrupt request. 3 KBE3 Keyboard line 3 Enable bit Cleared to enable standard I/O pin. Set to enable KBF. 3 bit in KBF register to generate an interrupt request. 2 KBE2 Keyboard line 2 Enable bit Cleared to enable standard I/O pin. Set to enable KBF. 2 bit in KBF register to generate an interrupt request. 1 KBE1 Keyboard line 1 Enable bit Cleared to enable standard I/O pin. Set to enable KBF. 1 bit in KBF register to generate an interrupt request. 0 KBE0 Keyboard line 0 Enable bit Cleared to enable standard I/O pin. Set to enable KBF. 0 bit in KBF register to generate an interrupt request. Reset Value= 0000 0000b 61 4105E–8051–02/08 Table 44. KBLS Register KBLS-Keyboard Level Selector Register (9Ch) 7 6 5 4 3 2 1 0 KBLS7 KBLS6 KBLS5 KBLS4 KBLS3 KBLS2 KBLS1 KBLS0 Bit Number Bit Mnemonic Description 7 KBLS7 Keyboard line 7 Level Selection bit Cleared to enable a low level detection on Port line 7. Set to enable a high level detection on Port line 7. 6 KBLS6 Keyboard line 6 Level Selection bit Cleared to enable a low level detection on Port line 6. Set to enable a high level detection on Port line 6. 5 KBLS5 Keyboard line 5 Level Selection bit Cleared to enable a low level detection on Port line 5. Set to enable a high level detection on Port line 5. 4 KBLS4 Keyboard line 4 Level Selection bit Cleared to enable a low level detection on Port line 4. Set to enable a high level detection on Port line 4. 3 KBLS3 Keyboard line 3 Level Selection bit Cleared to enable a low level detection on Port line 3. Set to enable a high level detection on Port line 3. 2 KBLS2 Keyboard line 2 Level Selection bit Cleared to enable a low level detection on Port line 2. Set to enable a high level detection on Port line 2. 1 KBLS1 Keyboard line 1 Level Selection bit Cleared to enable a low level detection on Port line 1. Set to enable a high level detection on Port line 1. 0 KBLS0 Keyboard line 0 Level Selection bit Cleared to enable a low level detection on Port line 0. Set to enable a high level detection on Port line 0. Reset Value= 0000 0000b 62 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Serial Port Interface (SPI) The Serial Peripheral Interface module (SPI) allows full-duplex, synchronous, serial communication between the MCU and peripheral devices, including other MCUs. Features Features of the SPI module include the following: Signal Description • Full-duplex, three-wire synchronous transfers • Master or Slave operation • Eight programmable Master clock rates • Serial clock with programmable polarity and phase • Master Mode fault error flag with MCU interrupt capability • Write collision flag protection Figure 20 shows a typical SPI bus configuration using one Master controller and many Slave peripherals. The bus is made of three wires connecting all the devices: Figure 24. SPI Master/Slaves interconnection Slave 1 MISO MOSI SCK SS MISO MOSI SCK SS VDD Slave 4 Slave 3 MISO MOSI SCK SS 0 1 2 3 MISO MOSI SCK SS MISO MOSI SCK SS PORT Master Slave 2 The Master device selects the individual Slave devices by using four pins of a parallel port to control the four SS pins of the Slave devices. Master Output Slave Input (MOSI) This 1-bit signal is directly connected between the Master Device and a Slave Device. The MOSI line is used to transfer data in series from the Master to the Slave. Therefore, it is an output signal from the Master, and an input signal to a Slave. A byte (8-bit word) is transmitted most significant bit (MSB) first, least significant bit (LSB) last. Master Input Slave Output (MISO) This 1-bit signal is directly connected between the Slave Device and a Master Device. The MISO line is used to transfer data in series from the Slave to the Master. Therefore, it is an output signal from the Slave, and an input signal to the Master. A byte (8-bit word) is transmitted most significant bit (MSB) first, least significant bit (LSB) last. SPI Serial Clock (SCK) This signal is used to synchronize the data movement both in and out the devices through their MOSI and MISO lines. It is driven by the Master for eight clock cycles which allows to exchange one byte on the serial lines. Slave Select (SS) Each Slave peripheral is selected by one Slave Select pin (SS). This signal must stay low for any message for a Slave. It is obvious that only one Master (SS high level) can 63 4105E–8051–02/08 drive the network. The Master may select each Slave device by software through port pins (Figure 20). To prevent bus conflicts on the MISO line, only one slave should be selected at a time by the Master for a transmission. In a Master configuration, the SS line can be used in conjunction with the MODF flag in the SPI Status register (SPSTA) to prevent multiple masters from driving MOSI and SCK (See Error conditions). A high level on the SS pin puts the MISO line of a Slave SPI in a high-impedance state. The SS pin could be used as a general purpose if the following conditions are met: • The device is configured as a Master and the SSDIS control bit in SPCON is set. This kind of configuration can be found when only one Master is driving the network and there is no way that the SS pin could be pulled low. Therefore, the MODF flag in the SPSTA will never be set(1). • The Device is configured as a Slave with CPHA and SSDIS control bits set(2) This kind of configuration can happen when the system comprises one Master and one Slave only. Therefore, the device should always be selected and there is no reason that the Master uses the SS pin to select the communicating Slave device. Note: 1. Clearing SSDIS control bit does not clear MODF. 2. Special care should be taken not to set SSDIS control bit when CPHA =’0’ because in this mode, the SS is used to start the transmission. Baud rate In Master mode, the baud rate can be selected from a baud rate generator which is controlled by three bits in the SPCON register: SPR2, SPR1 and SPR0.The Master clock is chosen from one of seven clock rates resulting from the division of the internal clock by 2, 4, 8, 16, 32, 64 or 128. Table 45 gives the different clock rates selected by SPR2:SPR1:SPR0: Table 45. SPI Master Baud Rate Selection 64 SPR2 SPR1 SPR0 Clock Rate Baud rate divisor (BD) 0 0 0 FCLK PERIPH /2 2 0 0 1 FCLK PERIPH /4 4 0 1 0 FCLK PERIPH / 8 8 0 1 1 FCLK PERIPH /16 16 1 0 0 FCLK PERIPH /32 32 1 0 1 FCLK PERIPH /64 64 1 1 0 FCLK PERIPH /128 128 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Functional Description Figure 25 shows a detailed structure of the SPI module. Figure 25. SPI Module Block Diagram Internal Bus SPDAT FCLK PERIPH Clock Divider /2 /4 /8 /16 /32 /64 /128 Shift Register 7 6 5 4 3 2 1 0 Receive Data Register Pin Control Logic Clock Logic MOSI MISO M S Clock Select SCK SS SPR2 SPEN SSDIS MSTR CPOL CPHA SPR1 SPR0 SPCON SPI Interrupt Request SPI Control 8-bit bus 1-bit signal SPSTA SPIF WCOL Operating Modes - MODF - - - - The Serial Peripheral Interface can be configured as one of the two modes: Master mode or Slave mode. The configuration and initialization of the SPI module is made through one register: • The Serial Peripheral CONtrol register (SPCON) Once the SPI is configured, the data exchange is made using: • SPCON • The Serial Peripheral STAtus register (SPSTA) • The Serial Peripheral DATa register (SPDAT) During an SPI transmission, data is simultaneously transmitted (shifted out serially) and received (shifted in serially). A serial clock line (SCK) synchronizes shifting and sampling on the two serial data lines (MOSI and MISO). A Slave Select line (SS) allows individual selection of a Slave SPI device; Slave devices that are not selected do not interfere with SPI bus activities. When the Master device transmits data to the Slave device via the MOSI line, the Slave device responds by sending data to the Master device via the MISO line. This implies full-duplex transmission with both data out and data in synchronized with the same clock (Figure 26). 65 4105E–8051–02/08 Figure 26. Full-Duplex Master-Slave Interconnection 8-bit Shift register SPI Clock Generator MISO MISO MOSI MOSI SCK SS Master MCU 8-bit Shift register SCK VDD SS VSS Slave MCU Master mode The SPI operates in Master mode when the Master bit, MSTR (1), in the SPCON register is set. Only one Master SPI device can initiate transmissions. Software begins the transmission from a Master SPI module by writing to the Serial Peripheral Data Register (SPDAT). If the shift register is empty, the byte is immediately transferred to the shift register. The byte begins shifting out on MOSI pin under the control of the serial clock, SCK. Simultaneously, another byte shifts in from the Slave on the Master’s MISO pin. The transmission ends when the Serial Peripheral transfer data flag, SPIF, in SPSTA becomes set. At the same time that SPIF becomes set, the received byte from the Slave is transferred to the receive data register in SPDAT. Software clears SPIF by reading the Serial Peripheral Status register (SPSTA) with the SPIF bit set, and then reading the SPDAT. Slave mode The SPI operates in Slave mode when the Master bit, MSTR (2), in the SPCON register is cleared. Before a data transmission occurs, the Slave Select pin, SS, of the Slave device must be set to’0’. SS must remain low until the transmission is complete. In a Slave SPI module, data enters the shift register under the control of the SCK from the Master SPI module. After a byte enters the shift register, it is immediately transferred to the receive data register in SPDAT, and the SPIF bit is set. To prevent an overflow condition, Slave software must then read the SPDAT before another byte enters the shift register (3). A Slave SPI must complete the write to the SPDAT (shift register) at least one bus cycle before the Master SPI starts a transmission. If the write to the data register is late, the SPI transmits the data already in the shift register from the previous transmission. Transmission Formats Software can select any of four combinations of serial clock (SCK) phase and polarity using two bits in the SPCON: the Clock POLarity (CPOL (4) ) and the Clock PHAse (CPHA4). CPOL defines the default SCK line level in idle state. It has no significant effect on the transmission format. CPHA defines the edges on which the input data are sampled and the edges on which the output data are shifted (Figure 22 and Figure 23). The clock phase and polarity should be identical for the Master SPI device and the communicating Slave device. 1. The SPI module should be configured as a Master before it is enabled (SPEN set). Also the Master SPI should be configured before the Slave SPI. 2. 3. The SPI module should be configured as a Slave before it is enabled (SPEN set). The maximum frequency of the SCK for an SPI configured as a Slave is the bus clock speed. Before writing to the CPOL and CPHA bits, the SPI should be disabled (SPEN =’0’). 4. 66 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Figure 27. Data Transmission Format (CPHA = 0) SCK cycle number 1 2 3 4 5 6 7 8 MSB bit6 bit5 bit4 bit3 bit2 bit1 LSB bit6 bit5 bit4 bit3 bit2 bit1 LSB SPEN (internal) SCK (CPOL = 0) SCK (CPOL = 1) MOSI (from Master) MISO (from Slave) MSB SS (to Slave) Capture point Figure 28. Data Transmission Format (CPHA = 1) 1 2 3 4 5 6 7 8 MOSI (from Master) MSB bit6 bit5 bit4 bit3 bit2 bit1 LSB MISO (from Slave) MSB bit6 bit5 bit4 bit3 bit2 bit1 SCK cycle number SPEN (internal) SCK (CPOL = 0) SCK (CPOL = 1) LSB SS (to Slave) Capture point Figure 29. CPHA/SS Timing MISO/MOSI Byte 1 Byte 2 Byte 3 Master SS Slave SS (CPHA = 0) Slave SS (CPHA = 1) As shown in Figure 28, the first SCK edge is the MSB capture strobe. Therefore the Slave must begin driving its data before the first SCK edge, and a falling edge on the SS pin is used to start the transmission. The SS pin must be toggled high and then low between each byte transmitted (Figure 25). Figure 29 shows an SPI transmission in which CPHA is’1’. In this case, the Master begins driving its MOSI pin on the first SCK edge. Therefore the Slave uses the first SCK edge as a start transmission signal. The SS pin can remain low between transmissions (Figure 24). This format may be preferable in systems having only one Master and only one Slave driving the MISO data line. 67 4105E–8051–02/08 Error conditions The following flags in the SPSTA signal SPI error conditions: Mode Fault (MODF) Mode Fault error in Master mode SPI indicates that the level on the Slave Select (SS) pin is inconsistent with the actual mode of the device. MODF is set to warn that there may have a multi-master conflict for system control. In this case, the SPI system is affected in the following ways: • An SPI receiver/error CPU interrupt request is generated, • The SPEN bit in SPCON is cleared. This disable the SPI, • The MSTR bit in SPCON is cleared When SS DISable (SSDIS) bit in the SPCON register is cleared, the MODF flag is set when the SS signal becomes’0’. However, as stated before, for a system with one Master, if the SS pin of the Master device is pulled low, there is no way that another Master attempt to drive the network. In this case, to prevent the MODF flag from being set, software can set the SSDIS bit in the SPCON register and therefore making the SS pin as a general purpose I/O pin. Clearing the MODF bit is accomplished by a read of SPSTA register with MODF bit set, followed by a write to the SPCON register. SPEN Control bit may be restored to its original set state after the MODF bit has been cleared. Write Collision (WCOL) A Write Collision (WCOL) flag in the SPSTA is set when a write to the SPDAT register is done during a transmit sequence. WCOL does not cause an interruption, and the transfer continues uninterrupted. Clearing the WCOL bit is done through a software sequence of an access to SPSTA and an access to SPDAT. Overrun Condition An overrun condition occurs when the Master device tries to send several data bytes and the Slave devise has not cleared the SPIF bit issuing from the previous data byte transmitted. In this case, the receiver buffer contains the byte sent after the SPIF bit was last cleared. A read of the SPDAT returns this byte. All others bytes are lost. This condition is not detected by the SPI peripheral. Interrupts Two SPI status flags can generate a CPU interrupt requests: Table 46. SPI Interrupts Flag Request SPIF (SP data transfer) SPI Transmitter Interrupt request MODF (Mode Fault) SPI Receiver/Error Interrupt Request (if SSDIS =’0’) Serial Peripheral data transfer flag, SPIF: This bit is set by hardware when a transfer has been completed. SPIF bit generates transmitter CPU interrupt requests. Mode Fault flag, MODF: This bit becomes set to indicate that the level on the SS is inconsistent with the mode of the SPI. MODF with SSDIS reset, generates receiver/error CPU interrupt requests. Figure 30 gives a logical view of the above statements. 68 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Figure 30. SPI Interrupt Requests Generation SPIF SPI Transmitter CPU Interrupt Request SPI CPU Interrupt Request MODF SPI Receiver/error CPU Interrupt Request SSDIS Registers There are three registers in the module that provide control, status and data storage functions. These registers are describes in the following paragraphs. Serial Peripheral Control register (SPCON) • The Serial Peripheral Control Register does the following: • Selects one of the Master clock rates, • Configure the SPI module as Master or Slave, • Selects serial clock polarity and phase, • Enables the SPI module, • Frees the SS pin for a general purpose Table 47 describes this register and explains the use of each bit. Table 47. SPCON Register SPCON - Serial Peripheral Control Register (0C3H) 7 6 5 4 3 2 1 0 SPR2 SPEN SSDIS MSTR CPOL CPHA SPR1 SPR0 Bit Number Bit Mnemonic 7 SPR2 6 SPEN Description Serial Peripheral Rate 2 Bit with SPR1 and SPR0 define the clock rate. Serial Peripheral Enable Cleared to disable the SPI interface. Set to enable the SPI interface. SS Disable 5 SSDIS 5 MSTR Cleared to enable SS# in both Master and Slave modes. Set to disable SS# in both Master and Slave modes. In Slave mode, this bit has no effect if CPHA =’0’. Serial Peripheral Master Cleared to configure the SPI as a Slave. Set to configure the SPI as a Master. Clock Polarity 4 CPOL Cleared to have the SCK set to’0’ in idle state. Set to have the SCK set to’1’ in idle low. Clock Phase 3 CPHA Cleared to have the data sampled when the SCK leaves the idle state (see CPOL). Set to have the data sampled when the SCK returns to idle state (see CPOL). 69 4105E–8051–02/08 Bit Number Bit Mnemonic 2 SPR1 1 SPR0 Description SPR2 SPR1 0 0 SPR0 Serial Peripheral Rate 0 FCLK PERIPH /2 0 0 1 FCLK PERIPH /4 0 1 0 FCLK PERIPH /8 0 1 1 FCLK PERIPH /16 1 0 0 FCLK PERIPH /32 1 0 1 FCLK PERIPH /64 1 1 0 FCLK PERIPH /128 1 1 1 Invalid Reset Value= 0001 0100b Not bit addressable Serial Peripheral Status Register (SPSTA) The Serial Peripheral Status Register contains flags to signal the following conditions: • Data transfer complete • Write collision • Inconsistent logic level on SS pin (mode fault error) Table 48 describes the SPSTA register and explains the use of every bit in the register. Table 48. SPSTA Register SPSTA - Serial Peripheral Status and Control register (0C4H) 7 6 5 4 3 2 1 0 SPIF WCOL - MODF - - - - Bit Number Bit Mnemonic Description Serial Peripheral data transfer flag 7 SPIF Cleared by hardware to indicate data transfer is in progress or has been approved by a clearing sequence. Set by hardware to indicate that the data transfer has been completed. Write Collision flag 6 WCOL Cleared by hardware to indicate that no collision has occurred or has been approved by a clearing sequence. Set by hardware to indicate that a collision has been detected. 5 - Reserved The value read from this bit is indeterminate. Do not set this bit. Mode Fault 4 MODF Cleared by hardware to indicate that the SS pin is at appropriate logic level, or has been approved by a clearing sequence. Set by hardware to indicate that the SS pin is at inappropriate logic level. 70 3 - 2 - Reserved The value read from this bit is indeterminate. Do not set this bit Reserved The value read from this bit is indeterminate. Do not set this bit T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Bit Number Bit Mnemonic Description 1 - 0 - Reserved The value read from this bit is indeterminate. Do not set this bit. Reserved The value read from this bit is indeterminate. Do not set this bit. Reset Value= 00X0 XXXXb Not Bit addressable Serial Peripheral DATa register (SPDAT) The Serial Peripheral Data Register (Table 49) is a read/write buffer for the receive data register. A write to SPDAT places data directly into the shift register. No transmit buffer is available in this model. A Read of the SPDAT returns the value located in the receive buffer and not the content of the shift register. Table 49. SPDAT Register SPDAT - Serial Peripheral Data Register (0C5H) 7 6 5 4 3 2 1 0 R7 R6 R5 R4 R3 R2 R1 R0 Reset Value= Indeterminate R7:R0: Receive data bits SPCON, SPSTA and SPDAT registers may be read and written at any time while there is no on-going exchange. However, special care should be taken when writing to them while a transmission is on-going: • Do not change SPR2, SPR1 and SPR0 • Do not change CPHA and CPOL • Do not change MSTR • Clearing SPEN would immediately disable the peripheral • Writing to the SPDAT will cause an overflow 71 4105E–8051–02/08 Hardware Watchdog Timer The WDT is intended as a recovery method in situations where the CPU may be subjected to software upset. The WDT consists of a 14-bit counter and the WatchDog Timer ReSeT (WDTRST) SFR. The WDT is by default disabled from exiting reset. To enable the WDT, user must write 01EH and 0E1H in sequence to the WDTRST, SFR location 0A6H. When WDT is enabled, it will increment every machine cycle while the oscillator is running and there is no way to disable the WDT except through reset (either hardware reset or WDT overflow reset). When WDT overflows, it will drive an output RESET HIGH pulse at the RST-pin. Using the WDT To enable the WDT, user must write 01EH and 0E1H in sequence to the WDTRST, SFR location 0A6H. When WDT is enabled, the user needs to service it by writing to 01EH and 0E1H to WDTRST to avoid WDT overflow. The 14-bit counter overflows when it reaches 16383 (3FFFH) and this will reset the device. When WDT is enabled, it will increment every machine cycle while the oscillator is running. This means the user must reset the WDT at least every 16383 machine cycle. To reset the WDT the user must write 01EH and 0E1H to WDTRST. WDTRST is a write only register. The WDT counter cannot be read or written. When WDT overflows, it will generate an output RESET pulse at the RST-pin. The RESET pulse duration is 96 x TCLK PERIPH, where TCLK PERIPH= 1/FCLK PERIPH. To make the best use of the WDT, it should be serviced in those sections of code that will periodically be executed within the time required to prevent a WDT reset. To have a more powerful WDT, a 27 counter has been added to extend the Time-out capability, ranking from 16ms to 2s @ FOSCA = 12MHz. To manage this feature, refer to WDTPRG register description, Table 50. Table 50. WDTRST Register WDTRST - Watchdog Reset Register (0A6h) 7 6 5 4 3 2 1 0 - - - - - - - - Reset Value = XXXX XXXXb Write only, this SFR is used to reset/enable the WDT by writing 01EH then 0E1H in sequence. 72 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Table 51. WDTPRG Register WDTPRG - Watchdog Timer Out Register (0A7h) 7 6 5 4 3 2 1 0 - - - - - S2 S1 S0 Bit Number Bit Mnemonic Description 7 - 6 - 5 - 4 - 3 - 2 S2 WDT Time-out select bit 2 1 S1 WDT Time-out select bit 1 0 S0 WDT Time-out select bit 0 Reserved The value read from this bit is undetermined. Do not try to set this bit. S2 0 0 0 0 1 1 1 1 S1 0 0 1 1 0 0 1 1 S0 0 1 0 1 0 1 0 1 Selected Time-out (214 - 1) machine cycles, 16. 3 ms @ FOSCA =12 MHz (215 - 1) machine cycles, 32.7 ms @ FOSCA=12 MHz (216 - 1) machine cycles, 65. 5 ms @ FOSCA=12 MHz (217 - 1) machine cycles, 131 ms @ FOSCA=12 MHz (218 - 1) machine cycles, 262 ms @ FOSCA=12 MHz (219 - 1) machine cycles, 542 ms @ FOSCA=12 MHz (220 - 1) machine cycles, 1.05 s @ FOSCA=12 MHz (221 - 1) machine cycles, 2.09 s @ FOSCA=12 MHz Reset value XXXX X000 WDT During Power Down In Power Down mode the oscillator stops, which means the WDT also stops. While in Power Down mode the user does not need to service the WDT. There are 2 methods of and Idle exiting Power Down mode: by a hardware reset or via a level activated external interrupt which is enabled prior to entering Power Down mode. When Power Down is exited with hardware reset, servicing the WDT should occur as it normally should whenever the T89C51RB2/RC2 is reset. Exiting Power Down with an interrupt is significantly different. The interrupt is held low long enough for the oscillator to stabilize. When the interrupt is brought high, the interrupt is serviced. To prevent the WDT from resetting the device while the interrupt pin is held low, the WDT is not started until the interrupt is pulled high. It is suggested that the WDT be reset during the interrupt service routine. To ensure that the WDT does not overflow within a few states of exiting of powerdown, it is better to reset the WDT just before entering powerdown. In the Idle mode, the oscillator continues to run. To prevent the WDT from resetting the T89C51RB2/RC2 while in Idle mode, the user should always set up a timer that will periodically exit Idle, service the WDT, and re-enter Idle mode. 73 4105E–8051–02/08 ONCE™ Mode (ON Chip Emulation) The ONCE mode facilitates testing and debugging of systems using T89C51RB2/RC2 without removing the circuit from the board. The ONCE mode is invoked by driving certain pins of the T89C51RB2/RC2; the following sequence must be exercised: • Pull ALE low while the device is in reset (RST high) and PSEN is high. • Hold ALE low as RST is deactivated. While the T89C51RB2/RC2 is in ONCE mode, an emulator or test CPU can be used to drive the circuit. The following table shows the status of the port pins during ONCE mode. Normal operation is restored when normal reset is applied. Table 52. External Pin Status during ONCE Mode ALE PSEN Port 0 Port 1 Port 2 Port 3 XTAL1/2 Weak pull-up Weak pull-up Float Weak pull-up Weak pull-up Weak pull-up Active "Once" is a registered trademark of Intel Corporation. 74 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Power Management Two power reduction modes are implemented in the T89C51RB2/RC2: the Idle mode and the Power-Down mode. These modes are detailed in the following sections. In addition to these power reduction modes, the clocks of the core and peripherals can be dynamically divided by 2 using the X2 mode detailed in Section “Clock”. Reset A reset is required after applying power at turn-on. To achieve a valid reset, the reset signal must be maintained for at least 2 machine cycles (24 oscillator clock periods) while the oscillator is running and stabilized and VCC established within the specified operating ranges. A device reset initializes the T89C51RB2/RC2 and vectors the CPU to address 0000h. RST input has a pull-down resistor allowing power-on reset by simply connecting an external capacitor to VDD as shown in Figure 31. Resistor value and input c h a r a c te r i s ti c s a r e d i s c u s s e d i n th e S e c t i on “ D C Ch a r a c t er i s ti c s ” o f t h e T89C51RB2/RC2 datasheet. The status of the Port pins during reset is detailed in Table 53. Figure 31. Reset Circuitry and Power-On Reset VDD To CPU core and peripherals + R RST RST RST VSS a. RST input circuitry b. Power-on Reset Table 53. Pin Conditions in Special Operating Modes Reset Recommendation to Prevent Flash Corruption Mode Port 0 Port 1 Port 2 Port 3 Port 4 ALE PSEN# Reset Floating High High High High High High Idle Data Data Data Data Data High High PowerDown Data Data Data Data Data Low Low A bad reset sequence will lead to bad microcontroller initialization and system registers like SFR’s, Program Counter, etc. will not be correctly initialized. A bad initialization may lead to unpredictable behaviour of the C51 microcontroller. An example of this situation may occur in an instance where the bit ENBOOT in AUXR1 register is initialized from the hardware bit BLJB upon reset. Since this bit allows mapping of the bootloader in the code area, a reset failure can be critical. If one wants the ENBOOT cleared inorder to unmap the boot from the code area (yet due to a bad reset) the bit ENBOOT in SFR’s may be set. If the value of Program Counter is accidently in the range of the boot memory addresses then a flash access (write or erase) may corrupt the Flash on-chip memory . It is recommended to use an external reset circuitry featuring power supply monitoring to prevent system malfunction during periods of insufficient power supply voltage(power supply failure, power supply switched off). 75 4105E–8051–02/08 Idle Mode An instruction that sets PCON. 0 indicates that it is the last instruction to be executed before going into Idle mode. In Idle mode, the internal clock signal is gated off to the CPU, but not to the interrupt, Timer, and Serial Port functions. The CPU status is preserved in its entirety: the Stack Pointer, Program Counter, Program Status Word, Accumulator and all other registers maintain their data during idle. The port pins hold the logical states they had at the time Idle was activated. ALE and PSEN hold at logic high level. There are two ways to terminate the Idle mode. Activation of any enabled interrupt will cause PCON. 0 to be cleared by hardware, terminating the Idle mode. The interrupt will be serviced, and following RETI the next instruction to be executed will be the one following the instruction that put the device into idle. The flag bits GF0 and GF1 can be used to give an indication if an interrupt occurred during normal operation or during idle. For example, an instruction that activates idle can also set one or both flag bits. When idle is terminated by an interrupt, the interrupt service routine can examine the flag bits. The other way of terminating the Idle mode is with a hardware reset. Since the clock oscillator is still running, the hardware reset needs to be held active for only two machine cycles (24 oscillator periods) to complete the reset. Power-down Mode To save maximum power, a power-down mode can be invoked by software (refer to Table 5, PCON register). In power-down mode, the oscillator is stopped and the instruction that invoked powerdown mode is the last instruction executed. The internal RAM and SFRs retain their value until the power-down mode is terminated. VCC can be lowered to save further power. Either a hardware reset or an external interrupt can cause an exit from powerdown. To properly terminate power-down, the reset or external interrupt should not be executed before VCC is restored to its normal operating level and must be held active long enough for the oscillator to restart and stabilize. Only external interrupts INT0, INT1 and Keyboard Interrupts are useful to exit from power-down. For that, interrupt must be enabled and configured as level or edge sensitive interrupt input. When Keyboard Interrupt occurs after a power down mode, 1024 clocks are necessary to exit to power down mode and enter in operating mode. Holding the pin low restarts the oscillator but bringing the pin high completes the exit as detailed in Figure 32. When both interrupts are enabled, the oscillator restarts as soon as one of the two inputs is held low and power down exit will be completed when the first input will be released. In this case the higher priority interrupt service routine is executed. Once the interrupt is serviced, the next instruction to be executed after RETI will be the one following the instruction that put T89C51RB2/RC2 into power-down mode. 76 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Figure 32. Power-down Exit Waveform INT0 INT1 XTALA or XTALB Active phase Power-down phase Oscillator restart phase Active phase Exit from power-down by reset redefines all the SFRs, exit from power-down by external interrupt does no affect the SFRs. Exit from power-down by either reset or external interrupt does not affect the internal RAM content. Note: If idle mode is activated with power-down mode (IDL and PD bits set), the exit sequence is unchanged, when execution is vectored to interrupt, PD and IDL bits are cleared and idle mode is not entered. Table shows the state of ports during idle and power-down modes. Table 54. State of Ports Mode Program Memory ALE PSEN PORT0 PORT1 PORT2 PORT3 Idle Internal 1 1 Port Data* Port Data Port Data Port Data Idle External 1 1 Floating Port Data Address Port Data Power Down Internal 0 0 Port Dat* Port Data Port Data Port Data Power Down External 0 0 Floating Port Data Port Data Port Data * Port 0 can force a 0 level. A "one" will leave port floating. 77 4105E–8051–02/08 Power-off Flag The power-off flag allows the user to distinguish between a “cold start” reset and a “warm start” reset. A cold start reset is the one induced by VCC switch-on. A warm start reset occurs while VCC is still applied to the device and could be generated for example by an exit from power-down. The power-off flag (POF) is located in PCON register (Table 55). POF is set by hardware when VCC rises from 0 to its nominal voltage. The POF can be set or cleared by software allowing the user to determine the type of reset. Table 55. PCON Register PCON - Power Control Register (87h) 7 6 5 4 3 2 1 0 SMOD1 SMOD0 - POF GF1 GF0 PD IDL Bit Number Bit Mnemonic Description 7 SMOD1 Serial port Mode bit 1 Set to select double baud rate in mode 1, 2 or 3. 6 SMOD0 Serial port Mode bit 0 Cleared to select SM0 bit in SCON register. Set to select FE bit in SCON register. 5 - Reserved The value read from this bit is indeterminate. Do not set this bit. 4 POF Power-Off Flag Cleared to recognize next reset type. Set by hardware when VCC rises from 0 to its nominal voltage. Can also be set by software. 3 GF1 General purpose Flag Cleared by user for general purpose usage. Set by user for general purpose usage. 2 GF0 General purpose Flag Cleared by user for general purpose usage. Set by user for general purpose usage. 1 PD Power-Down mode bit Cleared by hardware when reset occurs. Set to enter power-down mode. 0 IDL Idle mode bit Cleared by hardware when interrupt or reset occurs. Set to enter idle mode. Reset Value = 00X1 0000b Not bit addressable 78 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Reduced EMI Mode The ALE signal is used to demultiplex address and data buses on port 0 when used with external program or data memory. Nevertheless, during internal code execution, ALE signal is still generated. In order to reduce EMI, ALE signal can be disabled by setting AO bit. The AO bit is located in AUXR register at bit location 0.As soon as AO is set, ALE is no longer output but remains active during MOVX and MOVC instructions and external fetches. During ALE disabling, ALE pin is weakly pulled high. Table 56. AUXR Register AUXR - Auxiliary Register (8Eh) 7 6 5 4 3 2 1 0 - - M0 - XRS1 XRS0 EXTRAM AO Bit Number Bit Mnemonic Description 7 - 6 - Reserved The value read from this bit is indeterminate. Do not set this bit Reserved The value read from this bit is indeterminate. Do not set this bit Pulse length 5 M0 Cleared to stretch MOVX control: the RD/ and the WR/ pulse length is 6 clock periods (default). Set to stretch MOVX control: the RD/ and the WR/ pulse length is 30 clock periods. 4 - 3 XRS1 2 XRS0 Reserved The value read from this bit is indeterminate. Do not set this bit XRAM Size XRS1 0 XRS0 0 XRAM size 256 bytes (default) 0 1 512 bytes 1 0 768 bytes 1 1 1024 bytes EXTRAM bit Cleared to access internal XRAM using movx @ Ri/ @ DPTR. 1 EXTRAM Set to access external memory. Programmed by hardware after Power-up regarding Hardware Security Byte (HSB), default setting, XRAM selected. 0 AO ALE Output bit Cleared, ALE is emitted at a constant rate of 1/6 the oscillator frequency (or 1/3 if X2 mode is used). (default) Set, ALE is active only during a MOVX or MOVC instruction is used. 79 4105E–8051–02/08 Electrical Characteristics Absolute Maximum Ratings(*) Operating Temperature Range ...... 0°C to 70°C (Commercial) ................................................... -40°C to 85°C (Industrial) Storage Temperature ................................... -65°C to +150°C Voltage on VCC to VSS...................................-0.5V to + 6. 5V Note: *Stresses at or above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions may affect device reliability. Voltage on Any Pin to VSS ...................... -0.5V to VCC + 0.5V Power Dissipation ........................................................... 1 W(1) Note: 80 1. This value is based on the maximum allowable die temperature and the thermal resistance of the package. T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 DC Parameters for Standard Voltage TA = 0°C to +70°C; VSS = 0V; VCC = 5V ± 10%; F = 0 to 40 MHz. TA = -40°C to +85°C; VSS = 0V; VCC = 5V ± 10%; F = 0 to 40 MHz. Table 57. DC Parameters in Standard Voltage Symbol Parameter Min VIL Input Low Voltage VIH Input High Voltage except RST, XTAL1, VIH1 Input High Voltage RST, XTAL1 VOL Output Low Voltage, ports 1, 2, 3, 4 and 5 (6) VOL1 VOH VOH1 RRST Output Low Voltage, port 0, ALE, PSEN Typ Max Unit -0.5 0.2 VCC - 0.1 V 0.2 VCC + 0.9 VCC + 0.5 V 0.7 VCC VCC + 0.5 V (6) Output High Voltage, ports 1, 2, 3, 4 and 5 Output High Voltage, port 0, ALE, PSEN RST Pulldown Resistor 0.3 V IOL = 100 µA(4) 0.45 V IOL = 1.6 mA(4) 1.0 V IOL = 3.5 mA(4) 0.3 V IOL = 200 µA(4) 0.45 V IOL = 3.2 mA(4) 1.0 V IOL = 7. 0 mA(4) VCC - 0.3 V VCC - 0.7 V VCC - 1.5 V VCC - 0.3 V VCC - 0.7 V VCC - 1.5 V 50 90 (5) Test Conditions 200 kΩ IOH = -10 µA IOH = -30 µA IOH = -60 µA VCC = 5V ± 10% IOH = -200 µA IOH = -3.2 mA IOH = -7. 0 mA VCC = 5V ± 10% IIL Logical 0 Input Current ports 1, 2, 3, 4 and 5 -50 µA Vin = 0.45 V ILI Input Leakage Current ±10 µA 0.45V < Vin < VCC ITL Logical 1 to 0 Transition Current, ports 1, 2, 3, 4 and 5 -650 µA Vin = 2.0 V CIO Capacitance of I/O Buffer 10 pF Fc = 1 MHz TA = 25°C IPD Power Down Current 150 µA 4. 5V < VCC < 5. 5 V(3) TBD mA Power Supply Current on normal mode (7) 0.4 Freq (Mhz) + 3 mA mA Power Supply Current Flash programming (7) 0.4 Freq (Mhz) + 20 mA mA ICCIDLE ICC ICCOP1 Power Supply Current on idle mode (7) 100 Note: 3. Power Down ICC is measured with all output pins disconnected; EA = VSS, PORT 0 = VCC; XTAL2 NC. ; RST = VSS 4. Capacitance loading on Ports 0 and 2 may cause spurious noise pulses to be superimposed on the VOLs of ALE and Ports 1 and 3.The noise is due to external bus capacitance discharging into the Port 0 and Port 2 pins when these pins make 1 to 0 transitions during bus operation. In the worst cases (capacitive loading 100pF), the noise pulse on the ALE line may exceed 0.45V with maxi VOL peak 0.6V. A Schmitt Trigger use is not necessary. 5. Typicals are based on a limited number of samples and are not guaranteed. The values listed are at room temperature and 5V. 6. Under steady state (non-transient) conditions, IOL must be externally limited as follows: Maximum IOL per port pin: 10 mA Maximum IOL per 8-bit port: Port 0: 26 mA 81 4105E–8051–02/08 Ports 1, 2 and 3: 15 mA Maximum total IOL for all output pins: 71 mA If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test conditions. 7. For other values, please contact your sales office. DC Parameters for Low Voltage TA = 0°C to +70°C; VSS = 0V; VCC = 2.7V to 3.3V; F = 0 to 20 MHz. TA = -40°C to +85°C; VSS = 0V; VCC = 2.7V to 3.3V; F = 0 to 20 MHz. Table 58. DC Parameters for Low Voltage Symbol Parameter Min Typ Max Unit -0.5 0.2 VCC - 0.1 V 0.2 VCC + 0.9 VCC + 0.5 V 0.7 VCC VCC + 0.5 V Test Conditions VIL Input Low Voltage VIH Input High Voltage except RST, XTAL1 VIH1 Input High Voltage, RST, XTAL1 VOL Output Low Voltage, ports 1, 2, 3, 4 and 5 (6) 0.45 V IOL = 0.8 mA(4) VOL1 Output Low Voltage, port 0, ALE, PSEN (6) 0.45 V IOL = 1.6 mA(4) VOH Output High Voltage, ports 1, 2, 3, 4 and 5 0.9 VCC V IOH = -10 µA VOH1 Output High Voltage, port 0, ALE, PSEN 0.9 VCC V IOH = -40 µA IIL Logical 0 Input Current ports 1, 2, 3 -50 µA Vin = 0.45 V ILI Input Leakage Current ±10 µA 0.45V < Vin < VCC ITL Logical 1 to 0 Transition Current, ports 1, 2, 3, -650 µA Vin = 2.0 V 200 kΩ 10 pF Fc = 1 MHz TA = 25°C 50 µA VCC = 2.5V to 3.5 V(3) mA mA VCC = 3.3 V(1) VCC = 3.3 V(2) RRST RST Pulldown Resistor CIO Capacitance of I/O Buffer IPD Power Down Current 10 (5) ICC Power Supply Current (7) TBD Note: 50 90 (5) 1. Operating ICC is measured with all output pins disconnected; XTALA1 driven with TCLCH, TCHCL = 5 ns (see Figure 36.), VIL = VSS + 0.5 V, VIH = VCC - 0.5V; XTAL2 N. C. ; EA = RST = Port 0 = VCC. ICC would be slightly higher if a crystal oscillator used. 2. Idle ICC is measured with all output pins disconnected; XTAL1 driven with TCLCH, TCHCL = 5 ns, VIL = VSS + 0.5 V, VIH = VCC 0.5V; XTAL2 N. C; Port 0 = VCC; EA = RST = VSS (see Figure 33). 3. Power Down ICC is measured with all output pins disconnected; EA = VSS, PORT 0 = VCC; XTAL2 NC. ; RST = VSS 4. Capacitance loading on Ports 0 and 2 may cause spurious noise pulses to be superimposed on the VOLs of ALE and Ports 1 and 3.The noise is due to external bus capacitance discharging into the Port 0 and Port 2 pins when these pins make 1 to 0 transitions during bus operation. In the worst cases (capacitive loading 100pF), the noise pulse on the ALE line may exceed 0.45V with maxi VOL peak 0.6V. A Schmitt Trigger use is not necessary. 5. Typicals are based on a limited number of samples and are not guaranteed. The values listed are at room temperature and 5V. 6. Under steady state (non-transient) conditions, IOL must be externally limited as follows: Maximum IOL per port pin: 10 mA Maximum IOL per 8-bit port: Port 0: 26 mA Ports 1, 2 and 3: 15 mA Maximum total IOL for all output pins: 71 mA If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test conditions. 82 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 7. For other values, please contact your sales office. Figure 33. ICC Test Condition, Idle Mode VCC ICC VCC VCC P0 VCC RST EA XTAL2 XTAL1 (NC) CLOCK SIGNAL VSS All other pins are disconnected. Figure 34. ICC Test Condition, Operating Mode VCC ICC VCC VCC P0 RST EA XTAL2 XTAL1 VSS (NC) CLOCK SIGNAL All other pins are disconnected. Figure 35. ICC Test Condition, Power-Down Mode VCC ICC VCC VCC P0 RST (NC) EA XTAL2 XTAL1 VSS All other pins are disconnected. 83 4105E–8051–02/08 Figure 36. Clock Signal Waveform for ICC Tests in Active and Idle Modes VCC-0.5V 0.45V TCLCH TCHCL TCLCH = TCHCL = 5ns. 0.7VCC 0.2VCC-0.1 AC Parameters Explanation of the AC Symbols Each timing symbol has 5 characters. The first character is always a “T” (stands for time). The other characters, depending on their positions, stand for the name of a signal or the logical status of that signal. The following is a list of all the characters and what they stand for. Example: TAVLL = Time for Address Valid to ALE Low. TLLPL = Time for ALE Low to PSEN Low. TA = 0 to +70°C; VSS = 0V; VCC = 5V ± 10%; M range. TA = -40°C to +85°C; VSS = 0V; VCC = 5V ± 10%; M range. TA = 0 to +70°C; VSS = 0V; 2.7V < VCC < 3.3V; L range. TA = -40°C to +85°C; VSS = 0V; 2.7V < VCC < 3.3V; L range. (Load Capacitance for port 0, ALE and PSEN = 100 pF; Load Capacitance for all other outputs = 80 pF. ) Table 59, Table 62 and Table 65 give the description of each AC symbols. Table 68, Table 65 and Table 67 give for each range the AC parameter. Table 68, Table 67 and Table 66 give the frequency derating formula of the AC parameter for each speed range description. To calculate each AC symbols. take the x value in the corresponding column (-M or -L) and use this value in the formula. Example: TLLIU for -M and 20 MHz, Standard clock. x = 35 ns T 50 ns TCCIV = 4T - x = 165 ns 84 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 External Program Memory Characteristics Table 59. Symbol Description Symbol T Parameter Oscillator clock period TLHLL ALE pulse width TAVLL Address Valid to ALE TLLAX Address Hold After ALE TLLIV ALE to Valid Instruction In TLLPL ALE to PSEN TPLPH PSEN Pulse Width TPLIV PSEN to Valid Instruction In TPXIX Input Instruction Hold After PSEN TPXIZ Input Instruction Float After PSEN TAVIV Address to Valid Instruction In TPLAZ PSEN Low to Address Float Table 60. AC Parameters for a Fix Clock Symbol -M Min -L Max Min Units Max T 25 25 ns TLHLL 35 35 ns TAVLL 5 5 ns TLLAX 5 5 ns TLLIV 65 65 ns TLLPL 5 5 ns TPLPH 50 50 ns TPLIV TPXIX 30 0 30 0 ns ns TPXIZ 10 10 ns TAVIV 80 80 ns TPLAZ 10 10 ns 85 4105E–8051–02/08 Table 61. AC Parameters for a Variable Clock Symbol Type Standard Clock X2 Clock X parameter for -M range X parameter for -L range Units TLHLL Min 2T-x T-x 15 15 ns TAVLL Min T-x 0.5 T - x 20 20 ns TLLAX Min T-x 0.5 T - x 20 20 ns TLLIV Max 4T-x 2T-x 35 35 ns TLLPL Min T-x 0.5 T - x 15 15 ns TPLPH Min 3T-x 1.5 T - x 25 25 ns TPLIV Max 3T-x 1.5 T - x 45 45 ns TPXIX Min x x 0 0 ns TPXIZ Max T-x 0.5 T - x 15 15 ns TAVIV Max 5T-x 2.5 T - x 45 45 ns TPLAZ Max x x 10 10 ns External Program Memory Read Cycle Figure 37. External Program Memory Read Cycle 12 TCLCL TLHLL TLLIV ALE TLLPL TPLPH PSEN PORT 0 TLLAX TAVLL INSTR IN TPLIV TPLAZ A0-A7 TPXAV TPXIZ TPXIX INSTR IN A0-A7 INSTR IN TAVIV PORT 2 86 ADDRESS OR SFR-P2 ADDRESS A8-A15 ADDRESS A8-A15 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 External Data Memory Characteristics Table 62. Symbol Description Symbol Parameter TRLRH RD Pulse Width TWLWH WR Pulse Width TRLDV RD to Valid Data In TRHDX Data Hold After RD TRHDZ Data Float After RD TLLDV ALE to Valid Data In TAVDV Address to Valid Data In TLLWL ALE to WR or RD TAVWL Address to WR or RD TQVWX Data Valid to WR Transition TQVWH Data set-up to WR High TWHQX Data Hold After WR TRLAZ RD Low to Address Float TWHLH RD or WR High to ALE high Table 63. AC Parameters for a Fix Clock -M -L Symbol Min TRLRH 125 125 ns TWLWH 125 125 ns TRLDV TRHDX Max Min 95 0 Max 95 0 Units ns ns TRHDZ 25 25 ns TLLDV 155 155 ns TAVDV 160 160 ns 105 ns TLLWL 45 105 TAVWL 70 70 ns TQVWX 5 5 ns TQVWH 155 155 ns TWHQX 10 10 ns TRLAZ 0 0 ns TWHLH 5 45 45 5 45 ns 87 4105E–8051–02/08 Table 64. AC Parameters for a Variable Clock X parameter for - X parameter for M range L range Symbol Type Standard Clock X2 Clock Units TRLRH Min 6T-x 3T-x 25 25 ns TWLWH Min 6T-x 3T-x 25 25 ns TRLDV Max 5T-x 2.5 T - x 30 30 ns TRHDX Min x x 0 0 ns TRHDZ Max 2T-x T-x 25 25 ns TLLDV Max 8T-x 4T -x 45 45 ns TAVDV Max 9T-x 4. 5 T - x 65 65 ns TLLWL Min 3T-x 1.5 T - x 30 30 ns TLLWL Max 3T+x 1.5 T + x 30 30 ns TAVWL Min 4T-x 2T-x 30 30 ns TQVWX Min T-x 0.5 T - x 20 20 ns TQVWH Min 7T-x 3.5 T - x 20 20 ns TWHQX Min T-x 0.5 T - x 15 15 ns TRLAZ Max x x 0 0 ns TWHLH Min T-x 0.5 T - x 20 20 ns TWHLH Max T+x 0.5 T + x 20 20 ns External Data Memory Write Cycle Figure 38. External Data Memory Write Cycle TWHLH ALE PSEN TLLWL TWLWH WR TLLAX PORT 0 A0-A7 TQVWX TQVWH TWHQX DATA OUT TAVWL PORT 2 88 ADDRESS OR SFR-P2 ADDRESS A8-A15 OR SFR P2 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 External Data Memory Read Cycle Figure 39. External Data Memory Read Cycle TWHLH TLLDV ALE PSEN TLLWL RD TRLRH TRHDZ TAVDV TLLAX PORT 0 TRHDX A0-A7 DATA IN TRLAZ TAVWL PORT 2 ADDRESS OR SFR-P2 Serial Port Timing – Shift Register Mode ADDRESS A8-A15 OR SFR P2 Table 65. Symbol Description Symbol Parameter TXLXL Serial port clock cycle time TQVHX Output data set-up to clock rising edge TXHQX Output data hold after clock rising edge TXHDX Input data hold after clock rising edge TXHDV Clock rising edge to input data valid Table 66. AC Parameters for a Fix Clock -M -L Symbol Min TXLXL 300 300 ns TQVHX 200 200 ns TXHQX 30 30 ns TXHDX 0 0 ns TXHDV Max 117 Min Max 117 Units ns 89 4105E–8051–02/08 Table 67. AC Parameters for a Variable Clock Symbol Type Standard Clock X2 Clock X parameter for -M range X parameter for -L range TXLXL Min 12 T 6T TQVHX Min 10 T - x 5T-x 50 50 ns TXHQX Min 2T-x T-x 20 20 ns TXHDX Min x x 0 0 ns TXHDV Max 10 T - x 5 T- x 133 133 ns Units ns Shift Register Timing Waveforms Figure 40. Shift Register Timing Waveforms 0 INSTRUCTION 1 2 3 4 5 6 7 8 ALE TXLXL CLOCK TXHQX TQVXH OUTPUT DATA INPUT DATA 0 1 2 4 5 6 7 TXHDX TXHDV VALID WRITE to SBUF 3 VALID VALID SET TI VALID VALID VALID VALID SET RI CLEAR RI Flash EEPROM Programming and Verification Characteristics Table 68. Flash Programming Parameters TA = 21°C to 27°C; VSS = 0V; VCC = 5V ± 10%. Symbol 1/TCLCL 90 VALID Parameter Oscillator Frequency Min Max Units 4 6 MHz TEHAZ Control to address float 48 TCLCL TAVGL Address Setup to PROG Low 48 TCLCL TGHAX Address Hold after PROG 48 TCLCL TDVGL Data Setup to PROG Low 48 TCLCL TGHDX Data Hold after PROG 48 TCLCL TGLGH PROG Width for PGMC and PGXC* TGLGH PROG Width for PGML TAVQV Address to Valid Data 48 TCLCL TELQV ENABLE Low to Data Valid 48 TCLCL TEHQZ Data Float after ENABLE 10 20 ms 48 TCLCL 0 48 TCLCL T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Flash EEPROM Programming and Verification Waveforms Figure 41. Flash EEPROM Programming and Verification Waveforms PROGRAMMING P1.0-P1.7 P2.0-P2.4 P3.4-P3.5 VERIFICATION ADDRESS ADDRESS TAVQV P0 DATA OUT DATA IN TGHDX TGHAX TDVGL TAVGL ALE/PROG TGLGH TEHAZ CONTROL SIGNALS (ENABLE) External Clock Drive Characteristics (XTAL1) Table 69. External Clock Drive Characteristics (XTAL1) Symbol Parameter Min Max Units TCLCL Oscillator Period 25 ns TCHCX High Time 3 ns TCLCX Low Time 3 ns TCLCH Rise Time 3 ns TCHCL Fall Time 3 ns 60 % TCHCX/TCLCX External Clock Drive Waveforms TEHQZ TELQV Cyclic ratio in X2 mode 40 Figure 42. External Clock Drive Waveforms VCC-0.5V 0.45V 0.7VCC 0.2VCC-0.1 TCHCX TCLCH TCLCX TCHCL TCLCL AC Testing Input/Output Waveforms Figure 43. AC Testing Input/Output Waveforms VCC -0.5V INPUT/OUTPUT 0.45V 0.2 VCC + 0.9 0.2 VCC - 0.1 AC inputs during testing are driven at VCC - 0.5 for a logic “1” and 0.45V for a logic “0”. Timing measurement are made at VIH min. for a logic “1” and VIL max for a logic “0”. 91 4105E–8051–02/08 Float Waveforms Figure 44. Float Waveforms FLOAT VOH - 0.1 V VOL + 0.1 V VLOAD VLOAD + 0.1 V VLOAD - 0.1 V For timing purposes as port pin is no longer floating when a 100 mV change from load voltage occurs and begins to float when a 100 mV change from the loaded VOH/VOL level occurs. IOL/IOH ≥ ± 20 mA. Clock Waveforms 92 Valid in normal clock mode. In X2 mode XTAL2 must be changed to XTAL2/2. T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Figure 45. Clock Waveforms INTERNAL CLOCK STATE4 STATE5 STATE6 STATE1 STATE2 STATE3 STATE4 STATE5 P1 P1 P1 P1 P1 P1 P1 P1 P2 P2 P2 P2 P2 P2 P2 P2 XTAL2 ALE THESE SIGNALS ARE NOT ACTIVATED DURING THE EXECUTION OF A MOVX INSTRUCTION EXTERNAL PROGRAM MEMORY FETCH PSEN P0 DATA SAMPLED FLOAT P2 (EXT) PCL OUT DATA SAMPLED FLOAT PCL OUT DATA SAMPLED FLOAT PCL OUT INDICATES ADDRESS TRANSITIONS READ CYCLE RD PCL OUT (IF PROGRAM MEMORY IS EXTERNAL) P0 DPL OR Rt OUT P2 DATA SAMPLED FLOAT INDICATES DPH OR P2 SFR TO PCH TRANSITION WRITE CYCLE WR P0 PCL OUT (EVEN IF PROGRAM MEMORY IS INTERNAL) DPL OR Rt OUT PCL OUT (IF PROGRAM MEMORY IS EXTERNAL) DATA OUT P2 INDICATES DPH OR P2 SFR TO PCH TRANSITION PORT OPERATION MOV PORT SRC OLD DATA NEW DATA P0 PINS SAMPLED P0 PINS SAMPLED MOV DEST P0 MOV DEST PORT (P1.P2.P3) (INCLUDES INTO. INT1.TO T1) SERIAL PORT SHIFT CLOCK P1, P2, P3 PINS SAMPLED RXD SAMPLED P1, P2, P3 PINS SAMPLED RXD SAMPLED TXD (MODE 0) This diagram indicates when signals are clocked internally. The time it takes the signals to propagate to the pins, however, ranges from 25 to 125 ns. This propagation delay is dependent on variables such as temperature and pin loading. Propagation also varies from output to output and component. Typically though (TA=25°C fully loaded) RD and WR propagation delays are approximately 50ns. The other signals are typically 85 ns. Propagation delays are incorporated in the AC specifications. 93 4105E–8051–02/08 Flash EEPROM Memory The Flash memory increases EPROM and ROM functionality with in-circuit electrical erasure and programming. It contains 16K or 32K bytes of program memory organized respectively in 128 or 256 pages of 128 bytes. This memory is both parallel and serial In-System Programmable (ISP). ISP allows devices to alter their own program memory in the actual end product under software control. A default serial loader (bootloader) program allows ISP of the Flash. The programming does not require 12V external programming voltage. The necessary high programming voltage is generated on-chip using the standard V CC pins of the microcontroller. Features Flash Programming and Erasure • Flash E2PROM internal program memory. • Boot vector allows user provided Flash loader code to reside anywhere in the Flash memory space. This configuration provides flexibility to the user. • Default loader in Boot ROM allows programming via the serial port without the need of a user provided loader. • Up to 64K byte external program memory if the internal program memory is disabled (EA = 0). • Programming and erase voltage with standard 5V or 3V VCC supply. • Read/Programming/Erase: • Byte-wise read without wait state • Byte or page erase and programming (10 ms) • Typical programming time (32K bytes) in 10s • Parallel programming with 87C51 compatible hardware interface to programmer • Programmable security for the code in the Flash • 10k write cycles • 10 years data retention The 16K or 32K bytes Flash is programmed by bytes or by pages of 128 bytes. It is not necessary to erase a byte or a page before programming. The programming of a byte or a page includes a self erase before programming. There are three methods of programming the Flash memory: 94 • First, the on-chip ISP bootloader may be invoked which will use low level routines to program the pages. The interface used for serial downloading of Flash is the UART. • Second, the Flash may be programmed or erased in the end-user application by calling low-level routines through a common entry point in the Boot ROM. • Third, the Flash may be programmed using the parallel method by using a conventional EPROM programmer. The parallel programming method used by these devices is similar to that used by EPROM 87C51 but it is not identical and the commercially available programmers need to have support for the T89C51RB2/RC2. The bootloader and the Application Programming Interface (API) routines are located in the BOOT ROM. T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Flash Registers and Memory Map Hardware Register The T89C51RB2/RC2 Flash memory uses several registers for his management: • Hardware registers can only be accessed through the parallel programming modes which are handled by the parallel programmer. • Software registers are in a special page of the Flash memory which can be accessed through the API or with the parallel programming modes. This page, called "Extra Flash Memory", is not in the internal Flash program memory addressing space. The only hardware register of the T89C51RB2/RC2 is called Hardware Security Byte (HSB). Table 70. Hardware Security Byte (HSB) 7 6 5 4 3 2 1 0 X2 BLJB - - XRAM LB2 LB1 LB0 Bit Number Bit Mnemonic 7 X2 Description X2 Mode Programmed to force X2 mode (6 clocks per instruction) Unprogrammed to force X1 mode, Standard Mode. (Default) Boot Loader Jump Bit 6 BLJB Unprogrammed this bit to start the user’s application on next reset at address 0000h. Programmed this bit to start the boot loader at address F800h (Default). 5 - Reserved 4 - Reserved 3 XRAM XRAM config bit (only programmable by programmer tools) Programmed to inhibit XRAM Unprogrammed, this bit to valid XRAM (Default) 2-0 LB2-0 User Memory Lock Bits (only programmable by programmer tools) See Table 71 Boot Loader Jump Bit (BLJB) One bit of the HSB, the BLJB bit, is used to force the boot address: Flash Memory Lock Bits • When this bit is set the boot address is 0000h. • When this bit is reset the boot address is F800h. By default, this bit is cleared and the ISP is enabled. The three lock bits provide different levels of protection for the on-chip code and data, when programmed as shown in Table 71. 95 4105E–8051–02/08 Table 71. Program Lock Bits Program Lock Bits Security level LB0 LB1 LB2 1 U U U No program lock features enabled. Protection description 2 P U U MOVC instruction executed from external program memory is disabled from fetching code bytes from internal memory, EA is sampled and latched on reset, and further parallel programming of the Flash is disabled. ISP and software programming with API are still allowed. 3 X P U Same as 2, also verify through parallel programming interface is disabled. 4 X X P Same as 3, also external execution is disabled. (Default) Note: U: unprogrammed or "one" level. P: programmed or "zero" level. X: do not care WARNING: Security level 2 and 3 should only be programmed after Flash and code verification. These security bits protect the code access through the parallel programming interface. They are set by default to level 4. The code access through the ISP is still possible and is controlled by the "software security bits" which are stored in the extra Flash memory accessed by the ISP firmware. To load a new application with the parallel programmer, a chip erase must first be done. This will set the HSB in its inactive state and will erase the Flash memory. The part reference can always be read using Flash parallel programming modes. Default Values Software Registers The default value of the HSB provides parts ready to be programmed with ISP: • BLJB: Programmed force ISP operation. • X2: Unprogrammed to force X1 mode (Standard Mode). • XRAM: Unprogrammed to valid XRAM • LB2-0: Security level four to protect the code from a parallel access with maximum security. Several registers are used, in factory and by parallel programmers, to make copies of hardware registers contents. These values are used by Atmel ISP (see Section "In-System Programming (ISP)", page 101). These registers are in the "Extra Flash Memory" part of the Flash memory. This block is also called "XAF" or eXtra Array Flash. They are accessed in the following ways: • Commands issued by the parallel memory programmer. • Commands issued by the ISP software. • Calls of API issued by the application software. Several software registers described in Table 72. 96 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Table 72. Default Values Mnemonic Definition Default value Description SBV Software Boot Vector FCh HSB Copy of the Hardware security byte BSB Boot Status Byte 0FFh SSB Software Security Byte FFh Copy of the Manufacturer Code 58h ATMEL Copy of the Device ID #1: Family Code D7h C51 X2, Electrically Erasable Copy of the Device ID #2: memories F7h T89C51RB2/RC2 32KB size and type FBh T89C51RB2/RC2 16 KB Copy of the Device ID #3: name and revision EFh T89C51RB2/RC2 32KB, Revision 0 FFh T89C51RB2/RC2 16 KB, Revision 0 101x 1011b After programming the part by ISP, the BSB must be cleared (00h) in order to allow the application to boot at 0000h. The content of the Software Security Byte (SSB) is described in Table 72 and Table 74. To assure code protection from a parallel access, the HSB must also be at the required level. Table 73. Software Security Byte 7 6 5 4 3 2 1 0 - - - - - - LB1 LB0 Bit Bit Number Mnemonic 7 - Reserved Do not clear this bit. 6 - Reserved Do not clear this bit. 5 - Reserved Do not clear this bit. 4 - Reserved Do not clear this bit. 3 - Reserved Do not clear this bit. 2 - Reserved Do not clear this bit. 1-0 LB1-0 Description User Memory Lock Bits See Table 74 The two lock bits provide different levels of protection for the on-chip code and data, when programmed as shown to Table 74. 97 4105E–8051–02/08 Table 74. Program Lock bits of the SSB Program Lock Bits Security level LB0 LB1 1 U U No program lock features enabled. 2 P U ISP programming of the Flash is disabled. 3 X P Same as 2, also verify through ISP programming interface is disabled. Note: Flash Memory Status Protection description U: unprogrammed or "one" level. P: programmed or "zero" level. X: do not care WARNING: Security level 2 and 3 should only be programmed after Flash and code verification. T89C51RB2/RC2 parts are delivered in standard with the ISP boot in the Flash memory. After ISP or parallel programming, the possible contents of the Flash memory are summarized on the figure below: Figure 46. Flash memory possible contents 7FFFh T89C51RC2 32KB 3FFFh T89C51RB2 16KB Virgin Application Virgin or application Application Dedicated ISP Virgin or application Virgin or application Dedicated ISP 0000h Default Memory Organization After ISP After ISP After parallel programming After parallel programming After parallel programming In the T89C51RB2/RC2, the lowest 16K or 32K of the 64Kb program memory address space is filled by internal Flash. When the EA pin high, the processor fetches instructions from internal program Flash. Bus expansion for accessing program memory from 16K or 32K upward automatic since external instruction fetches occur automatically when the program counter exceeds 3FFFh (16K) or 7FFFh (32K). If the EA pin is tied low, all program memory fetches are from external memory. 98 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Boot process Boot Flash When the user application programs its own Flash memory, all of the low level details are handled by a code that is permanently contained in a 2k byte “Boot ROM”. A user program simply calls the common entry point in the Boot ROM with appropriate parameters to accomplish the desired operation. Boot ROM operations include: erase block, program byte or page, verify byte or page, program security lock bit, etc. The Boot ROM is placed in the program memory space at the top of the address space from F800h to FFFFh. Figure 47. Boot ROM loader memory map FFF0 Entry point for API F800 ISP start Reset Code Execution At the falling edge of reset (unless the hardware conditions on PSEN, EA and ALE are set as described below), the T89C51RB2/RC2 reads the BLJB bit in the HSB byte. If this bit is set, it jumps to 0000h and if not, it jumps to F800h. At this address, the boot software reads a special Flash register: the Software Boot Vector (SBV). If the BSB is set to zero, power-up execution starts at location 0000h, which is the normal start address of the user’s application code. When the Boot Status Bit is set, the contents of the Boot Vector is used as the high byte of the execution address and the low byte is set to 00h. The factory default setting is FCh, corresponding to default ROM ISP boot loader. A custom boot loader can be written with the Boot Vector set to the custom boot loader address. Hardware Activation of the Boot Loader The default boot loader can also be executed by holding PSEN LOW, EA HIGH, and ALE HIGH (or not connected) at the falling edge of RESET. This allows an application to be built that will normally execute the end user’s code but can be manually forced into default ISP operation. As PSEN has the same structure as P1-P3, the current to force PSEN to 0 as ITL is defined in the DC parameters. User application should take care to release hardware conditions (PSEN LOW, EA HIGH) 24 clock cycles after falling edge of reset signal. If the factory default setting for the Boot Vector (FCh) is changed, it will no longer point to the ISP default Flash boot loader code. It can be restored: • With the default ISP activated with hardware conditions on PSEN, EA and ALE. • With a customized loader (in the end user application) that provides features for erasing and reprogramming of the Software Boot Vector and BSB. • Through the parallel programming method. 99 4105E–8051–02/08 After programming the Flash, the status byte should be programmed to zero in order to allow execution of the user’s application code beginning at address 0000h. Boot Process Summary The boot process is summarized on the following flowchart: Figure 48. Boot process flowchart RESET If BLJB=0 then ENBOOT bit (AUXR1) is set else ENBOOT bit (AUXR1) is cleared Yes (PSEN = 0, EA = 1, and ALE =1 or not connected) Hardware Hardware condition? FCON = 00h FCON = F0h BLJB=1 ENBOOT=0 BLJB!= 0 ? BLJB=0 ENBOOT=1 F800h Software FCON = 00h ? yes = hardware boot conditions BSB = 00h ? PC=0000h USER APPLICATION SBV = FCh ? USER BOOT LOADER Atmel BOOT LOADER PC= [SBV]00h 100 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 In-System Programming (ISP) The In-System Programming (ISP) is performed without removing the microcontroller from the system. The ISP facility consists of a series of internal hardware resources coupled with internal firmware to facilitate remote programming of theT89C51RB2/RC2 through the serial port. The Atmel ISP facility has made in-circuit programming in an embedded application possible with a minimum of additional expense in components and circuit board area. The ISP function through UART uses four pins: TxD, RxD, VSS, VCC. Only a small connector needs to be available to interface the application to an external circuit in order to use this feature. Using In-System Programming (ISP) The ISP feature allows a wide range of baud rates in the user application. It is also adaptable to a wide range of oscillator frequencies. This is accomplished by measuring the bit-time of a single bit in a received character. This information is then used to program the baud rate in terms of timer counts based on the oscillator frequency. The ISP featur e requir es that an initial char acter ( an uppercase U) be sent to the T89C51RB2/RC2 to establish the baud rate. The ISP firmware provides auto-echo of received characters. Once baud rate initialization has been performed, the ISP firmware will only accept Intel Hex-type records. Intel Hex records consist of ASCII characters used to represent hexadecimal values and are summarized below: :NNAAAARRDD. DDCC T89C51RB2/RC2 will accept up to 16 (10h) data bytes. The “AAAA” string represents the address of the first byte in the record. If there are zero bytes in the record, this field is often set to ‘‘0000’’. The “RR” string indicates the record type. A record type of “00” is a data record. A record type of “01” indicates the end-of-file mark. In this application, additional record types will be added to indicate either commands or data for the ISP facility. The “DD” string represents the data bytes. The maximum number of data bytes in a record is limited to 16 (decimal). The “CC” string represents the checksum byte. ISP commands are summarized in Table 75. As a record is received by the T89C51RB2/RC2, the information in the record is stored internally and a checksum calculation is performed and compared to ‘‘CC’’. The operation indicated by the record type is not performed until the entire record has been received. Should an error occur in the checksum, the T89C51RB2/RC2 will send an “X” out the serial port indicating a checksum error. If the checksum calculation is found to match the checksum in the record, then the command will be executed. In most cases, successful reception of the record will be indicated by transmitting a “. ” character out the serial port (displaying the contents of the internal program memory is an exception). In the case of a Data Record (record type ‘‘00’’), an additional check is made. A “. ” character will NOT be sent unless the record checksum matched the calculated checksum and all of the bytes in the record were successfully programmed. For a data record, an “X” indicates that the checksum failed to match, and an “R” character indicates that one of the bytes did not properly program. FLIP, a software utility to implement ISP programming with a PC, is available from the Atmel the web site. 101 4105E–8051–02/08 Table 75. Intel-Hex Records Used by In-system Programming RECORD TYPE COMMAND/DATA FUNCTION Data Record :nnaaaa00dd. . . . ddcc Where: Nn = number of bytes (hex) in record 00 aaaa = memory address of first byte in record dd. . . . dd = data bytes cc = checksum Example: :05008000AF5F67F060B6 End of File (EOF), no operation :xxxxxx01cc Where: 01 xxxxxx = required field, but value is a “don’t care” cc = checksum Example: :00000001FF Specify Oscillator Frequency (Not required, left for Philips compatibility) :01xxxx02ddcc Where: 02 xxxx = required field, but value is a “don’t care” dd = required field, but value is a “don’t care” cc = checksum Example: :0100000210ED 102 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 RECORD TYPE COMMAND/DATA FUNCTION Miscellaneous Write Functions :nnxxxx03ffssddcc Where: nn = number of bytes (hex) in record xxxx = required field, but value is a “don’t care” 03 = Write Function ff = subfunction code ss = selection code dd = data input (as needed) cc = checksum Subfunction Code = 01 (Erase Block) ff = 01 ss = block number in bits 7:5, Bits 4:0 = zeros Example: :0200000301A05A erase block 5 Subfunction Code = 04 (Reset Boot Vector and Status Byte) ff = 04 ss = don’t care dd = don’t care Example: :020000034500F8 Reset boot vector (FCh) and status byte (FFh) 03 Subfunction Code = 05 (Program Software Security Bits) ff = 05 ss = 00 program software security bit 1 (Level 2 inhibit writing to Flash) ss = 01 program software security bit 2 (Level 3 inhibit Flash verify) ss = 02 program security bit 3 (No effect, left for Philips compatibility; disable external memory is already set in the default hardware security byte) Example: :020000030501F6 program security bit 2 Subfunction Code = 06 (Program Boot Status Byte, Boot Vector,X2 bit,Osc bit or BLJB fuse bit) ff = 06 ss = 00 program Boot Status byte ss = 01 program Software Boot vector ss = 02 program X2 bit ss = 04 program BLJB Example: :03000003060100F5 program boot vector with 00 Subfunction Code = 07 (Full chip erase) ff = 07 ss = don’t care dd = don’t care Example: :03000007F5 program boot vector with 00 103 4105E–8051–02/08 RECORD TYPE COMMAND/DATA FUNCTION Display Device Data or Blank Check Record type 04 causes the contents of the entire Flash array to be sent out the serial port in a formatted display. This display consists of an address and the contents of 16 bytes starting with that address. No display of the device contents will occur if security bit 2 has been programmed. The dumping of the device data to the serial port is terminated by the reception of any character. General Format of Function 04 :05xxxx04sssseeeeffcc Where: 05 = number of bytes (hex) in record 04 xxxx = required field, but value is a “don’t care” 04 = “Display Device Data or Blank Check” function code ssss = starting address eeee = ending address ff = subfunction 00 = display data 01 = blank check cc = checksum Example: :0500000440004FFF0069 (display 4000–4FFF) Miscellaneous Read Functions General Format of Function 05 :02xxxx05ffsscc Where: 02 = number of bytes (hex) in record xxxx = required field, but value is a “don’t care” 05= “Miscellaneous Read” function code ffss = subfunction and selection code 05 0000 = read copy of the signature byte – manufacturer id (58H) 0001 = read copy of the signature byte – device ID# 1 (Family code) 0002 = read copy of the signature byte – device ID # 2 (Memories size and type) 0003 = read copy of the signature byte – device ID # 3 (Product name and revision) 0700 = read the software security bits 0701 = read BSB 0702 = read SBV 0704 = read HSB cc = checksum Example: :020000050001F0 read copy of the signature byte – device id # 1 In-application Programming Method Several Application Program Interface (API) calls are available for use by an application program to permit selective erasing and programming of Flash pages. All calls are made through a common interface, PGM_MTP. The programming functions are selected by setting up the microcontroller’s registers before making a call to PGM_MTP at FFF0h. Results are returned in the registers. The API calls are shown in Table . A set of Philips® compatible API calls is provided. When several bytes have to be programmed, it is highly recommended to use the Atmel API “PROGRAM DATA PAGE” call. Indeed, this API call writes up to 128 bytes in a single command. 104 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Table 76. API Calls API Call Parameter Input Parameters: R0 = osc freq (integer Not required, left for Philips compatibility) R1 = 02h PROGRAM DATA BYTE DPTR = address of byte to program ACC = byte to program Return Parameter ACC = 00 if pass,!00 if fail Input Parameters: R0 = osc freq (integer Not required) R1 = 09h DPTR0 = address of the first byte to program in the Flash memory PROGRAM DATA PAGE DPTR1 = address in XRAM of the first data to program (second data pointer) ACC = number of bytes to program Return Parameter ACC = 00 if pass,!00 if fail Remark: number of bytes to program is limited such as the Flash write remains in a single 128bytes page. Hence, when ACC is 128, valid values of DPL are 00h, or, 80h. Input Parameters: R0 = osc freq (integer Not required, left for Philips compatibility) R1 = 01h DPH = block number ERASE BLOCK Number 0 DPTR 0 Block 00h256 bytes (default) 1 20h 512 bytes 2 40h 768 bytes DPL = 00h Return Parameter None Remark: Command for Philips compatibility, as no erase is needed; the ISP firmware write FFh in the corresponding block. Input Parameters: R0 = osc freq (integer Not required, left for Philips compatibility) ERASE BOOT VECTOR R1 = 04h DPH = 00h DPL = don’t care Return Parameter none 105 4105E–8051–02/08 Table 76. API Calls (Continued) API Call Parameter Input Parameters: R0 = osc freq (integer Not required, left for Philips compatibility) R1 = 05h DPH = 00h PROGRAM SOFTWARE SECURITY BIT DPL = 00h – security bit # 1 (inhibit writing to Flash) 01h – security bit # 2 (inhibit Flash verify) 10h - allows ISP writing to Flash (see Note 1) 11h - allows ISP Flash verify (see Note 1) Return Parameter none Input Parameters: R0 = osc freq (integer Not required, left for Philips compatibility) R1 = 06h PROGRAM BOOT STATUS BYTE DPH = 00h DPL = 00h ACC = status byte Return Parameter ACC = status byte Input Parameters: R0 = osc freq (integer Not required, left for Philips compatibility) R1 = 06h PROGRAM BOOT VECTOR DPH = 00h DPL = 01h ACC = boot vector Return Parameter ACC = boot vector Input Parameters: R0 = osc freq (integer Not required, left for Philips compatibility) R1 = 0Ah PROGRAM X2 MODE DPH = 00h DPL = 08h ACC = value (00 or 01h) Return Parameter ACC = boot vector Input Parameters: R0 = osc freq (integer Not required, left for Philips compatibility) R1 = 0Ah PROGRAM BLJB DPH = 00h DPL = 04h ACC = value (00 or 01h) Return Parameter ACC = boot vector Input Parameters: R1 = 03h READ DEVICE DATA DPTR = address of byte to read Return Parameter ACC = value of byte read 106 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Table 76. API Calls (Continued) API Call Parameter Input Parameters: R0 = osc freq (integer Not required, left for Philips compatibility) R1 = 00h READ copy of the DPH = 00h MANUFACTURER ID DPL = 00h (manufacturer ID) Return Parameter ACC = value of byte read Input Parameters: R0 = osc freq (integer Not required, left for Philips compatibility) READ copy of the device ID # 1 R1 = 00h DPH = 00h DPL = 01h (device ID # 1) Return Parameter ACC = value of byte read Input Parameters: R0 = osc freq (integer Not required, left for Philips compatibility) READ copy of the device ID # 2 R1 = 00h DPH = 00h DPL = 02h (device ID # 2) Return Parameter ACC = value of byte read Input Parameters: R0 = osc freq (integer Not required, left for Philips compatibility) READ copy of the device ID # 3 R1 = 00h DPH = 00h DPL = 03h (device ID # 2) Return Parameter ACC = value of byte read Input Parameters: R0 = osc freq (integer Not required, left for Philips compatibility) READ SOFTWARE SECURITY BITS R1 = 07h DPH = 00h DPL = 00h (Software security bits) Return Parameter ACC = value of byte read Input Parameters: R0 = osc freq (integer Not required, left for Philips compatibility) READ HARDWARE SECURITY BITS R1 = 07h -> OBh DPH = 00h DPL = 04h (Hardware security bits) Return Parameter ACC = value of byte read 107 4105E–8051–02/08 Table 76. API Calls (Continued) API Call Parameter Input Parameters: R0 = osc freq (integer Not required, left for Philips compatibility) READ BOOT STATUS BYTE R1 = 07h DPH = 00h DPL = 01h (status byte) Return Parameter ACC = value of byte read Input Parameters: R0 = osc freq (integer Not required, left for Philips compatibility) READ BOOT VECTOR R1 = 07h DPH = 00h DPL = 02h (boot vector) Return Parameter ACC = value of byte read Note: 108 These functions can only be called by user’s code. The standard boot loader cannot decrease the security level. Number DPTR Block 0 00h 0 - 8 KB 1 20h 8 - 16 KB 2 40h 16 - 32 KB (Only on T89C51RC2) T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Ordering Information Table 77. Possible Order Entries Part-number Memory size Supply voltage Temperature range Package Packing T89C51RB2-3CSCM T89C51RB2-3CSIM T89C51RB2-SLSCM T89C51RB2-SLSIM T89C51RB2-SLSIL T89C51RB2-RLTIM T89C51RB2-RLTIL OBSOLETE T89C51RC2-3CSCM T89C51RC2-3CSIM T89C51RC2-SLSCM T89C51RC2-SLSIM T89C51RC2-SLSIL T89C51RC2-RLTIM T89C51RC2-RLTIL 109 4105E–8051–02/08 Package Information PDIL40 110 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Package Information VQFP44 Package Information PLC44 111 4105E–8051–02/08 112 T89C51RB2/RC2 4105E–8051–02/08 T89C51RB2/RC2 Document Revision History Changes from 4105C 02/02 to 4105D - 10-06 1. Correction to PDIL40 figure on page 5. Changes from 4105D 10-06 to 4105E - 02-08 1. Removed non-green part numbers from ordering information. 113 4105E–8051–02/08 Table of Contents Features ................................................................................................. 1 Description ............................................................................................ 1 Block Diagram ....................................................................................... 2 SFR Mapping ......................................................................................... 3 Pin Configurations ................................................................................ 5 Oscillator ............................................................................................... 9 Registers............................................................................................................... 9 Functional Block Diagram................................................................................... 10 Enhanced Features ............................................................................. 11 X2 Feature .......................................................................................................... 11 Dual Data Pointer Register DPTR ...................................................... 15 Expanded RAM (XRAM) ..................................................................... 18 Registers............................................................................................................. 20 Timer 2 ................................................................................................. 21 Auto-Reload Mode.............................................................................................. 21 Programmable Clock-Output .............................................................................. 22 Registers............................................................................................................. 24 Programmable Counter Array PCA ................................................... 26 Registers............................................................................................................. PCA Capture Mode............................................................................................. 16-bit Software Timer/ Compare Mode............................................................... High Speed Output Mode ................................................................................... Pulse Width Modulator Mode.............................................................................. PCA Watchdog Timer ......................................................................................... 28 34 35 36 37 37 Serial I/O Port ...................................................................................... 39 Framing Error Detection ..................................................................................... Automatic Address Recognition.......................................................................... Registers............................................................................................................. Baud Rate Selection for UART for Mode 1 and 3............................................... UART Registers.................................................................................................. 39 40 42 42 45 Interrupt System ................................................................................. 50 Registers............................................................................................................. 51 i 4105E–8051–02/08 Interrupt Sources and Vector Addresses............................................................ 58 Keyboard Interface ............................................................................. 59 Registers............................................................................................................. 60 Serial Port Interface (SPI) ................................................................... 63 Features.............................................................................................................. 63 Signal Description............................................................................................... 63 Functional Description ........................................................................................ 65 Hardware Watchdog Timer ................................................................ 72 Using the WDT ................................................................................................... 72 WDT During Power Down and Idle..................................................................... 73 ONCE™ Mode (ON Chip Emulation) .................................................. 74 Power Management ............................................................................ 75 Reset .................................................................................................................. Reset Recommendation to Prevent Flash Corruption ........................................ Idle Mode ............................................................................................................ Power-down Mode.............................................................................................. 75 75 76 76 Power-off Flag ..................................................................................... 78 Reduced EMI Mode ............................................................................. 79 Electrical Characteristics ................................................................... 80 Absolute Maximum Ratings(*) ................................................................................................................. 80 DC Parameters for Standard Voltage ................................................................. 81 DC Parameters for Low Voltage .........................................................................82 AC Parameters ................................................................................................... 84 Flash EEPROM Memory ..................................................................... 94 Features.............................................................................................................. 94 Flash Programming and Erasure........................................................................ 94 Flash Registers and Memory Map...................................................................... 95 Flash Memory Status.......................................................................................... 98 Memory Organization ......................................................................................... 98 Boot process....................................................................................................... 99 In-System Programming (ISP).......................................................................... 101 In-application Programming Method................................................................. 104 Ordering Information ........................................................................ 109 Package Information ........................................................................ 110 PDIL40.............................................................................................................. 110 ii 4105E–8051–02/08 Package Information ........................................................................ 111 VQFP44 ............................................................................................................ 111 Package Information ........................................................................ 111 PLC44............................................................................................................... 111 Document Revision History ............................................................. 113 Changes from 4105C - 02/02 to 4105D - 10-06 ............................................... 113 Changes from 4105D - 10-06 to 4105E - 02-08 ............................................... 113 Table of Contents .................................................................................. i iii 4105E–8051–02/08 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60 ASIC/ASSP/Smart Cards 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80 Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © Atmel Corporation 2008. All rights reserved. Atmel ®, logo and combinations thereof, are registered trademarks, and Everywhere You Are SM are the trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Printed on recycled paper. 4105E–8051–02/08