Advanced Power Electronics Corp. APE1117A 1A LOW DROPOUT LINEAR REGULATOR FEATURES DESCRIPTION 1.5V Maximum Dropout at Full Load Current Fast Transient Response Output Current Limiting Built-in Thermal Shutdown Good Noise Rejection Need only 1uF Capacitor for Stability Low-ESR Ceramic Capacitor Required for Output Stability. APE1117A is a low dropout positive adjustable or fixed-mode regulator with minimum of 1A output current capability. The product is specifically designed to provide well-regulated supply for low voltage IC applications such as high-speed bus termination and low current 3.3V logic supply. APE1117A is also well suited for other applications such as VGA cards. APE1117A is guaranteed to have lower than 1.4V dropout at full load current making it ideal to provide well-regulated outputs of 1.25 to 5.0 with 6.4V to 12V input supply. 3-Terminal Adjustable or Fixed 1.5V, 1.8V, 2.5V, 3.3V, 5.0V Packages : SOT-223, TO-252, SOT-89. Halogen Free Product TYPICAL APPLICATION 5V 5V C1 1uF C1 1uF Vin Vin Vout GND 3.3V/1A C2 1uF Tab is Vout ( 5V/3.3V fixed output ) Vo Vout Adj R1 121Ω R2 121Ω C2 1uF Tab is Vout ( 5V/2.5V ADJ output ) Note : Vo = VREF x (1+ Data and specifications subject to change without notice 2.5V/1A R2 ) R1 1 20130104E Advanced Power Electronics Corp. APE1117A ABSOLUTE MAXIMUM RATINGS (at TA=25°C) DC Supply Voltage(VIN) ---------------------------------Power Dissipation(PD) Note o -0.3V to 15V o @TA=25 C, TJ=125 C SOT-223 ------ 850mW SOT-89 -------- 330mW TO-252 -------- 1050mW Storage Temperature Range(T ST) --------------------- -65°C To 150°C Operating Junction Temperature Range(T J) -------- -40°C To 125°C Maximum Junction Temperature(T MJ) ---------------- 150°C Thermal Resistance from Junction to Case(R thjc) SOT-223 ------ 15°C/W SOT-89 -------- 100°C/W TO-252 -------- 10°C/W Thermal Resistance from Junction to Ambient(R thja) Note SOT-223 ------ 117°C/W SOT-89 -------- 300°C/W TO-252 -------- 92°C/W Note. No heat sink; No air flow) ORDERING/PACKAGE INFORMATION APE1117 AX - XX (Top View) Tab is VOUT Package Type Output Voltage K : SOT-223 G(GR) : SOT-89 H : TO-252 Blank : ADJ 15 : 1.5V 18 : 1.8V 19 : 1.9V 25 : 2.5V 33 : 3.3V 50 : 5.0V SOT-223 1 2 SOT-89 (G) 3 1 2 3 (Top View) Tab is VOUT (Top View) Tab is VOUT (Top View) Tab is VOUT SOT-89 (GR) 1 2 TO-252 3 1 ADJ/ GND VOUT VIN ADJ/ GND VOUT VIN ADJ/ GND VIN VOUT 3 2 VOUT ADJ/ GND VIN ELECTRICAL SPECIFICATIONS (TA=25°C, unless otherwise specified) Parameter Operation Input Voltage TEST CONDITION Minimum Load Current APE1117AXADJ/15/18/25 IOUT = 1A , δVOUT=1%VOUT /33/50 APE1117AXADJ/15/18/25 (VIN-VOUT) = 3V /33/50 APE1117AX-XX 0°C≦TJ≦125°C Line Regulation APE1117AX-XX Dropout Voltage(VIN-VOUT) Current Limit IOUT=10mA, VOUT+1.5V<VIN<VOUT<12V, TJ=25°C (Note 1,2) MIN 2.75 TYP - MAX 12 UNITS - 1.3 1.5 V 1.1 - - A - 5 10 mA - 0.2 0.5 % V 2 Advanced Power Electronics Corp. APE1117A ELECTRICAL SPECIFICATIONS(Cont.) Parameter APE1117AX-ADJ APE1117AX-15 APE1117AX-18 Load Regulation APE1117AX-25 APE1117AX-33 APE1117AX-50 Reference Voltage APE1117AX-18 APE1117AX-25 APE1117AX-33 APE1117AX-50 Ripple Rejection Temperature Stability VIN=3V, 10mA≦IOUT≦1A, TJ=25°C (Note 1,2) VIN=3.3V, 0mA≦IOUT ≦ 1A, TJ=25° C (Note 1,2) VIN=4V, 10mA≦IOUT≦1A, TJ=25°C (Note 1,2) VIN=5V,10mA≦IOUT ≦1A, TJ=25°C (Note 1,2) VIN=6.5V,10mA≦IOUT ≦1A, TJ=25° C (Note 1,2) APE1117AX-ADJ IOUT = 10mA, TJ=25°C, (VIN-VOUT)=1.5V APE1117AX-15 Output Voltage TEST CONDITION VIN=3.3V,10mA≦IOUT≦1A, TJ=25°C IOUT = 10mA, TJ = 25°C, 3V≦VIN≦ 12V IOUT = 10mA, TJ = 25°C, 3.3V≦VIN ≦12V IOUT = 10mA, TJ = 25°C, 4V≦VIN≦ 12V IOUT = 10mA, TJ = 25°C, 4.8V≦VIN ≦12V IOUT = 10mA, TJ = 25°C, 6.5V≦VIN ≦12V F=120Hz,COUT=10uF, APE1117AXXX, (VIN-VOUT) = 3V, IOUT = 1A IOUT=10mA MIN - TYP 0.4 MAX 1 UNITS - 12 15 mV - 15 18 mV - 20 25 mV - 26 33 mV - 40 50 mV 1.225 1.25 1.275 V 1.47 1.5 1.53 V 1.764 1.8 1.836 V 2.45 2.5 2.55 V 3.235 3.3 3.365 V 4.9 5 5.1 V - 60 70 dB - 0.5 - % % Note1: See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant junction temperature by low duty cycle pulse testing. Load regulation is measured at the output lead = 1/18” from the package. Note2: Line and load regulation are guaranteed up to the maximum power dissipation of 15W. Power dissipation is determined by the difference between input and output differential and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range. Note3: Quiescent current is defined as the minimum output current required in maintaining regulation. At 12V input/output differential the device is guaranteed to regulate if the output current is greater than 10mA. 3 Advanced Power Electronics Corp. APE1117A PIN DESCRIPTIONS PIN SYMBOL ADJ/GND PIN DESCRIPTION A resistor divider from this pin to the VOUT pin and ground sets the output voltage. (Ground only for Fixed-Mode) VOUT The output of the regulator. A minimum of 1uF capacitor ( 10mΩ < ESR < 1Ω) must be connected from this pin to ground to insure stability. VIN The input pin of regulator. A minimum of 1uF capacitor is connected from this pin to ground to insure that the input voltage does not sag below the minimum dropout voltage during the load transient response. This pin must always be 1.5V higher than VOUT in order for the device to regulate properly. BLOCK DIAGRAM Vin 3 2 Vout + + - 1.25V CURRENT LIMIT 1 + Thermal Shutdown + - GND (FIXED) 1 Adj 4 Advanced Power Electronics Corp. APE1117A TYPICAL PERFORMANCE CHARACTERISTICS 0.20 1.6 1.4 Output Voltage Deviation (%) Tj=25℃ Dropout Voltage (V) 1.2 1 0.8 0.6 Tj= 125℃ 0.4 0.2 0 0.4 0.2 0 0.8 0.6 0 I load=800mA -0.20 -0.40 -0.80 1 -1 Output Current (A) -25 Dropout Voltage vs Output Current 25 0 50 75 100 125 Temperature (℃) Load Regulation vs Temperature 2 1 1.5 Output Voltage Deviation (%) Output Voltage Change (%) 0.8 1 0. 5 0 -0.5 -1 -1.5 -2 -50 -25 0 25 50 75 100 125 150 0.6 0.4 0.2 0 Temperature (℃) 2 4 6.5 Cin=1uF Cout= 10 uF Tantalum 5.5 40 20 0 -20 -40 0 20 40 60 80 100 120 140 160 180 200 TIME (us) Line Transient Response 8 10 12 Line Regulation Load Current (A) Output Voltage Deviation ( mV) Output VoltageDeviation (mV) Input Voltage (V) Percent Change in Output Voltage vs Temperature 7.5 6 Input Voltage (V) 30 C in =1uF C out= 10 uF Tantalum Preload= 100mA 20 10 0 - 10 - 20 2 1 0 -1 0 10 20 30 40 50 60 70 80 90 100 TIME (us) Load Transient Response 5 Advanced Power Electronics Corp. APE1117A MARKING INFORMATION SOT-223 Part Number : XXXXXX YWWSSS Part Number Marking APE1117AK 1117A APE1117AK-15 117A-15 APE1117AK-18 117A-18 APE1117AK-19 117A-19 APE1117AK-25 117A-25 APE1117AK-33 117A-33 APE1117AK-50 117A-50 Date Code (YWWSSS) Y:Year WW：Week SSS：Sequence SOT-89 Identification code : XXXX YWWS Date Code (YWWS) Y:Year WW：Week S：Sequence Part Number Identification code APE1117AG(GR) 17AA(R) APE1117AG(GR)-15 17AB(R) APE1117AG(GR)-18 17AC(R) APE1117AG(GR)-19 17AG(R) APE1117AG(GR)-25 17AD(R) APE1117AG(GR)-33 17AE(R) APE1117AG(GR)-50 17AF(R) TO-252 Part Number : XXXXXX Logo YWWSSS Part Number Marking APE1117AH 1117A APE1117AH-15 117A-15 APE1117AH-18 117A-18 APE1117AH-19 117A-19 APE1117AH-25 117A-25 APE1117AH-33 117A-33 APE1117AH-50 117A-50 Date Code (YWWSSS) Y：Last Digit Of The Year WW：Week SSS：Sequence 6